ZTE ZXHN H298A - Test Mode

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.08.18 02:37:15 =~=~=~=~=~=~=~=~=~=~=~=


DRAMC V2.0 (0)



DRAMC V2.3.0.2 (0)



MT751020 at Tue Jul 4 16:33:16 CST 2017 version 1.1 free bootbase

Memory size 128MB

NAND Page size:2048B,Total size 128MB

bmt pool size: 81

board ip address:192.168.1.254
reset DECT & SWITCH start.
..
reset DECT & SWITCH over.

*** Press 1 means entering boot mode***
*** Press 2 means entering testing mode***
*** Press 3 means entering norm mode***
.........
Entering test mode ...



Found image at 0x01680000

Found image at 0x01a80000
****Try the second image...
rootfs 1:addr:87700000--size:900000
decompress_addr 1a80100 decompress_addr_end 1e80000
Decompress to 80002000 free_mem_ptr=80600000 free_mem_ptr_end=80780000
75xx: 0x80
Uncompressing [LZMA] ...  done.
Linux version 2.6.36 ([email protected]) (gcc version 4.3.4 (GCC) ) #1 SMP Tue Jan 2 14:23:32 CST 2018
ISPRAM0: PA=00330000,Size=00008000,enabled
DSPRAM0: PA=1dff8000,Size=00001000,enabled
Check boot para cksum...
bde bdeboot para cksum OK!
Boot 2'th image
bootPara reserved_fs_size=900000
bootPara.runmode=2
pdt_verinfo_init: tcVerInfo->RunMode[2]
bootPara.bootWhichImg=2
bootPara.img_info_tbl[0].flashOffset=0x 1680000
hw_ver=00
sHardVersion=V1.0.00
memsize:128MB
Ralink MT751020 SOC prom init
bootconsole [early0] enabled
CPU revision is: 00019555 (MIPS 34Kc)
Determined physical RAM map:
 memory: 076e0000 @ 00020000 (usable)
Wasting 1024 bytes for tracking 32 unused pages
Zone PFN ranges:
  Normal   0x00000020 -> 0x00007700
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000020 -> 0x00007700
3 available secondary CPU TC(s)
PERCPU: Embedded 7 pages/cpu @810f3000 s7232 r8192 d13248 u65536
pcpu-alloc: s7232 r8192 d13248 u65536 alloc=16*4096
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 30194
Kernel command line:  es=1
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00021654
Readback ErrCtl register=00021654
nmi base is 8114c200
Memory: 114728k/121728k available (3288k kernel code, 7000k reserved, 791k data, 232k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
	RCU-based detection of stalled CPUs is disabled.
	Verbose stalled-CPUs detection is disabled.
NR_IRQS:64
CPU frequency 750.00 MHz
 Using 266.667 MHz high precision timer.
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
Calibrating delay loop... 498.07 BogoMIPS (lpj=2490368)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
34K sync es set to 1.
Config7: 0x80080500
Limit of 4 TCs set
TLB of 64 entry pairs shared by 2 VPEs
VPE 0: TC 0 1 2, VPE 1: TC 3
IPI buffer pool of 16 buffers
CPU revision is: 00019555 ((null))
TC 1 going on-line as CPU 1
CPU revision is: 00019555 ((null))
TC 2 going on-line as CPU 2
CPU revision is: 00019555 ((null))
TC 3 going on-line as CPU 3
Brought up 4 CPUs
NET: Registered protocol family 16
11930:22:53 [KMONITOR][Notice] [monitor.c(938)MonitorInit]  cspmonitor init... !
MT7510_pcie_init:1
check pcie link up status:
isRC0_LINKUP=1
isRC1_LINKUP=1
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
pci 0000:00:01.0: BAR 8: assigned [mem 0x20100000-0x201fffff]
pci 0000:00:01.0: BAR 9: assigned [mem 0x20200000-0x202fffff pref]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff] (PCI address [0x20000000-0x200fffff]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [io  disabled]
pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
pci 0000:00:00.0:   bridge window [mem pref disabled]
pci 0000:02:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff 64bit]
pci 0000:02:00.0: BAR 0: set to [mem 0x20100000-0x201fffff 64bit] (PCI address [0x20100000-0x201fffff]
pci 0000:02:00.0: BAR 6: assigned [mem 0x20200000-0x2020ffff pref]
pci 0000:00:01.0: PCI bridge to [bus 02-02]
pci 0000:00:01.0:   bridge window [io  disabled]
pci 0000:00:01.0:   bridge window [mem 0x20100000-0x201fffff]
pci 0000:00:01.0:   bridge window [mem 0x20200000-0x202fffff pref]
PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
11930:22:54 [KQOS][Info] [qos.c(4999)CSPKernel_QoS_I] Qos module init
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
TC3162 hardware watchdog module loaded.
spitest init OK!
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 224
cryptomgr_test used greatest stack depth: 15632 bytes left
io scheduler noop registered (default)
ttyS0 at I/O 0xbfbf0003 (irq = 1) is a TC3162
brd: module loaded
tc3162 mtd init: mt6573_nand_init enter
MediaTek MT6573 Nand driver init, version v2.0
tc3162: flash device 0x01000000 at 0x1c000000
tc3162 mtd init: nandflash_probe enter
Allocate 16 byte aligned buffer: 8044d4f0
Enable NFI Clock
# MT6573 NAND # : Use HW ECC
manu_id=c2, dev_id=f1
ext_id=809502,
Device found in MTK table, ID: c2f1
[NAND] pagesz:2048 eccsz: 32, oobsz: 128
Support this Device in MTK table! c2f1

NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit)
bmt pool size: 81
Init bmt table, size: 81
bmt count: 81, system count: 943
begin to search BMT from block 1023
Match bmt signature @ block: 1023
Valid BMT, version v1
bmt found at block: 1023, mapped block: 0
Load bmt data success @ block 1023
BMT v1.total 0 mapping
Match bbt signature
BBT Checksum is: 0xd7
Valid BBT, version v1
bbt found, bad block count: 1
init_bbt->badblock_table[0]: 468
Load bbt data success
[mt6573_nand] probe successfully!
Creating 8 MTD partitions on "MT6573-Nand":
0x000000000000-0x000008000000 : "Whole flash"
mtd: partition "Whole flash" extends beyond the end of device "MT6573-Nand" -- size truncated to 0x75c0000
0x000000000000-0x000000040000 : "Bootloader"
0x000000040000-0x000000080000 : "tag"
0x000000080000-0x000000280000 : "config"
0x000000280000-0x000001680000 : "rootfs1"
0x000001680000-0x000001a80000 : "kernel1"
0x000001a80000-0x000001e80000 : "kernel2"
0x000001e80000-0x000003280000 : "rootfs2"
physmap mtd driver register!!!
pkq map rom ram_flash:offset:87700000---size:900000
!!!! led bink!!!
RT3xxx EHCI/OHCI init.
nf_conntrack version 0.5.0 (1792 buckets, 7168 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
PPP generic driver version 2.4.2
NET: Registered protocol family 24
11930:22:55 [KSWETH][Notice] [sweth_core.c(2818)sweth_init] SW&ETH HAL driver initing!
11930:22:55 [KSWETH][Notice] [sweth_core.c(144)CreateSwEthObjs] Create SW & ETH objects
11930:22:55 [KSWETH][Notice] [sweth_core.c(160)CreateSwEthObjs] Failed to get SWITCH attr, iRet=-2
11930:22:55 [KSWETH][Info] [sweth_core.c(167)CreateSwEthObjs] nEmac = 1, nSw = 0, nEth=5.
11930:22:55 [KSWETH][Warn] [sweth_core.c(314)CreateSwEthObjs] Failed to get TAG_PARA_MAC1!
11930:22:55 [KSWETH][Info] [sweth_core.c(326)CreateSwEthObjs] ETH obj0: PhyType = 1, Is_assoc_sw = 0, Emac = 0, Phy = 0
11930:22:55 [KSWETH][Warn] [sweth_core.c(314)CreateSwEthObjs] Failed to get TAG_PARA_MAC1!
11930:22:55 [KSWETH][Info] [sweth_core.c(326)CreateSwEthObjs] ETH obj1: PhyType = 1, Is_assoc_sw = 0, Emac = 0, Phy = 1
11930:22:55 [KSWETH][Warn] [sweth_core.c(314)CreateSwEthObjs] Failed to get TAG_PARA_MAC1!
11930:22:55 [KSWETH][Info] [sweth_core.c(326)CreateSwEthObjs] ETH obj2: PhyType = 1, Is_assoc_sw = 0, Emac = 0, Phy = 2
11930:22:55 [KSWETH][Warn] [sweth_core.c(314)CreateSwEthObjs] Failed to get TAG_PARA_MAC1!
11930:22:55 [KSWETH][Info] [sweth_core.c(326)CreateSwEthObjs] ETH obj3: PhyType = 1, Is_assoc_sw = 0, Emac = 0, Phy = 3
11930:22:55 [KSWETH][Warn] [sweth_core.c(314)CreateSwEthObjs] Failed to get TAG_PARA_MAC1!
11930:22:55 [KSWETH][Info] [sweth_core.c(326)CreateSwEthObjs] ETH obj4: PhyType = 1, Is_assoc_sw = 0, Emac = 0, Phy = 4
11930:22:55 [LEDKEYDRV][Info] [ledkey_mod.c(1163)KeyModuleInit] Warning!The supplied protect time is less than 1000ms,so use the default protect time 1000ms
11930:22:55 [LEDKEYDRV][Info] [ledkey_mod.c(1163)KeyModuleInit] Warning!The supplied protect time is less than 1000ms,so use the default protect time 1000ms
11930:22:55 [LEDKEYDRV][Info] [ledkey_mod.c(1163)KeyModuleInit] Warning!The supplied protect time is less than 1000ms,so use the default protect time 1000ms
11930:22:55 [TAGPARAM][Info] [tagparam_mod.c(1348)TagaramodInit] Tagaram module Driver Version 0.0.1.
11930:22:55 [TAGPARAM][Info] [tagparam_mod.c(1381)TagaramodInit] parse tag param success
Jiffies_test Driver Init Successfully
logger: created 1024K log 'logger_main' major '99'
: success register character device for /dev/monitor
11930:22:55 [MIRROR][Notice] [cspmirror.c(1262)mirror_init] ***********mirror_init************
systools version:v0.7.0
errorEPC = 96229600
11930:22:55 [KIGMPSNP][Info] [br_multicast_se(7334)br_mcparam_init] info init!
11930:22:55 [KQOS][Info] [qp_meter_api.c(66)QoSPolicerMeter] Register Meter(stb)
11930:22:55 [KQOS][Info] [qp_meter_api.c(66)QoSPolicerMeter] Register Meter(srtc)
11930:22:55 [KQOS][Info] [qp_meter_api.c(66)QoSPolicerMeter] Register Meter(trtc)
11930:22:55 [KQOS][Info] [qp_meter_api.c(66)QoSPolicerMeter] Register Meter(hard)
11930:22:55 [KQOS][Info] [qp_act_api.c(66)QoSPolicerActRe] Register Action(null)
11930:22:55 [KQOS][Info] [qp_act_api.c(66)QoSPolicerActRe] Register Action(drop)
11930:22:55 [KQOS][Info] [qp_act_api.c(66)QoSPolicerActRe] Register Action(dscp_mark)
11930:22:55 [KQOS][Info] [qp_act_api.c(66)QoSPolicerActRe] Register Action(vlan_prio_mark)
11930:22:55 [KQOS][Info] [qp_act_api.c(66)QoSPolicerActRe] Register Action(dscp_vlan_prio_mark)
child_dev_init start
child_dev_ioctl_set set[8031b69c]
11930:22:55 [Kernm255][Info] [ver_info.c(406)ver_info_init] ver_info_init
11930:22:55 [Kernm255][Info] [ver_info.c(195)ReadInfoFromVer] ver_info_init
11930:22:55 [Kernm255][Info] [ver_info.c(202)ReadInfoFromVer] ver_info_init
11930:22:55 [Kernm255][Info] [ver_info.c(218)ReadInfoFromVer] wFirmwareForm is:0x1
11930:22:55 [KSWETH][Notice] [csp_ifinfo.c(221)csp_ifinfo_init] Initializing CSP IFinfo...
khelper used greatest stack depth: 14864 bytes left
kworker/u:1 used greatest stack depth: 14792 bytes left
register AF_INET filter failed
#######begin FDB_Notify Reg
#######after FDB_Notify Reg
#######begin FDB_Notify Reg
Shouldn't be in WHILE
#######after FDB_Notify Reg
11930:22:55 [LEDKEYDRV][Error] [ledkey_callback(26)keycallback_ini] Install WPS KEY Callback Failed!
VFS: Mounted root (squashfs filesystem) readonly on device 31:8.
Freeing unused kernel memory: 232k freed
busybox init and set aff
sched_setaffinity cpu all success
Algorithmics/MIPS FPU Emulator v1.5
mount used greatest stack depth: 14288 bytes left
init debug mode!!!
/etc/init.debug: line 74: can't create /proc/rtl_reg: nonexistent directory
/etc/init.debug: line 75: usleep: not found
/etc/init.debug: line 76: can't create /proc/rtl_reg: nonexistent directory
/etc/init.debug: line 77: usleep: not found
/etc/init.debug: line 78: can't create /proc/rtl_reg: nonexistent directory
/etc/init.debug: line 79: usleep: not found
/etc/init.debug: line 80: can't create /proc/rtl_reg: nonexistent directory
/etc/init.debug: line 81: usleep: not found
procfile used greatest stack depth: 14168 bytes left
/etc/init.debug: line 95: usleep: not found
/etc/init.debug: line 97: usleep: not found
interface eth0 does not exist!
interface eth1 does not exist!
interface eth2 does not exist!
interface eth3 does not exist!
interface eth4 does not exist!
/etc/init.debug: line 104: usleep: not found
device br0 entered promiscuous mode
########br's FDB_MAX[256]
bridge name	bridge id		STP enabled	interfaces
br0		8000.00d0d0112132	no
/etc/init.debug: line 116: /etc/sh used greatest stack depth: 14096 bytes left
Wireless/CL1800/host_insmod.sh: not found
/etc/init.debug: line 117: usleep: not found
/etc/init.debug: line 118: /etc/Wireless/CL1800/ce_prod.sh: not found


H168NV31

login: admin
Password:
Login incorrect
H168NV31

login: admin
Password:
Login incorrect
H168NV31

login: superadmin
Password:
Login inco

H168NV31

login: superadmin
Password:
Login incorrect
H168NV31

login: admin
Password:
Login incorrect
H168NV31

login: admin
Password:
Login inco

H168NV31

login: hyper     admin
Password:
Login incorrect
H168NV31

login: administrator
Password:
Login incorrect
H168NV31

login:
H168NV31

login: 

H168NV31

login:

H168NV31

login: :q
Password:
Login incorrect
H168NV31

login: root
Password:
Login incorrect
H168NV31

login:

Log

H168NV31

login: avanzado
Password:
Login incorrect
H168NV31

login: