G12A:BL:0253b8:61aa2d;FEAT:E0F83180:2000;POC:F;RCY:0;EMMC:0;READ:0;CHK:1F;READ:0;CHK:1F;READ:0;CHK:1F;SD?:0;SD:0;READ:0;0.0
                                                                                                                           l2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0001 - pwm id 0x00
bl2_stage_init 0xc0
bl2_stage_init 0x02

no sdio debug board detected
L0:00000000
L1:00000703
L2:00008067
L3:04000000
S1:00000000
B2:00002000
B1:e0f83180

TE: 441964

BL2 Built : 15:21:48, Aug 28 2019. g12a g1bf2b53 - luan.yuan@droid15-sz

Board ID = 2
Set cpu clk to 24M
Set clk81 to 24M
CPU clk: 1200 MHz
Set clk81 to 166.6M
DDR driver_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 15:21:45
board id: 2
Load FIP HDR from SD, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
fw parse done
Load ddrfw from SD, src: 0x00060200, des: 0xfffd0000, size: 0x0000c000, part: 0
Load ddrfw from SD, src: 0x00038200, des: 0xfffd0000, size: 0x00004000, part: 0
PIEI prepare done
fastboot data load
fastboot data verify
verify result: 266
Cfg max: 2, cur: 1. Board id: 255. Force loop cfg
LPDDR4 probe
ddr clk to 792MHz
Load ddrfw from SD, src: 0x0003c200, des: 0xfffd0000, size: 0x0000c000, part: 0

dmc_version 0000
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of Write leveling coarse delay
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Load ddrfw from SD, src: 0x00048200, des: 0xfffd0000, size: 0x0000c000, part: 0
Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!

channel==0
RxClkDly_Margin_A0==236 ps 12
TxDqDly_Margin_A0==216 ps 11
RxClkDly_Margin_A1==216 ps 11
TxDqDly_Margin_A1==236 ps 12
TrainedVREFDQ_A0==74
TrainedVREFDQ_A1==74
VrefDac_Margin_A0==24
DeviceVref_Margin_A0==40
VrefDac_Margin_A1==23
DeviceVref_Margin_A1==40


channel==1
RxClkDly_Margin_A0==216 ps 11
TxDqDly_Margin_A0==236 ps 12
RxClkDly_Margin_A1==236 ps 12
TxDqDly_Margin_A1==236 ps 12
TrainedVREFDQ_A0==74
TrainedVREFDQ_A1==74
VrefDac_Margin_A0==23
DeviceVref_Margin_A0==40
VrefDac_Margin_A1==25
DeviceVref_Margin_A1==40

 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004

soc_vref_reg_value 0x 00000014 00000015 00000014 00000013 00000013 00000015 00000014 00000015 00000014 00000016 00000015 00000016 00000013 00000015 00000014 00000014 00000015 00000014 00000015 00000014 00000016 00000013 00000013 00000016 00000013 00000015 00000015 00000016 00000016 00000014 00000014 00000016 dram_vref_reg_value 0x 00000061
2D training succeed
aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 13:53:31
auto size-- 65535DDR cs0 size: 2048MB
DDR cs1 size: 2048MB
DMC_DDR_CTRL: 00e00024DDR size: 3928MB
cs0 DataBus test pass
cs1 DataBus test pass
cs0 AddrBus test pass
cs1 AddrBus test pass

100bdlr_step_size ps== 478
result report
boot times 0Enable ddr reg access
Load FIP HDR from SD, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
Load BL3X from SD, src: 0x0006c200, des: 0x0175c000, size: 0x00098000, part: 0
bl2z: ptr: 05129330, size: 00001e40
0.0;M3 CHK:0;cm4_sp_mode 0
MVN_1=0x00000000
MVN_2=0x00000000
[Image: g12a_v1.1.3390-6ac5299 2019-09-26 14:09:46 luan.yuan@droid15-sz]
OPS=0x30
ring efuse init
28 0b 30 00 01 21 15 00 00 09 38 38 34 55 30 50
[0.017150 Inits done]
secure task start!
high task start!
low task start!
run into bl31
NOTICE:  BL31: v1.3(release):4fc40b1
NOTICE:  BL31: Built : 15:57:33, May 22 2019
NOTICE:  BL31: G12A normal boot!
NOTICE:  BL31: BL33 decompress pass
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2022.01-meson-g12a (Mar 11 2022 - 20:14:10 +0200) radxa-zero

Model: Radxa Zero
SoC:   Amlogic Meson G12A (S905Y2) Revision 28:b (30:2)
DRAM:  3.8 GiB
MMC:   sd@ffe03000: 0, sd@ffe05000: 1, mmc@ffe07000: 2
Loading Environment from nowhere... OK
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found U-Boot script /boot/boot.scr
5655 bytes read in 3 ms (1.8 MiB/s)
## Executing script at 08000000
108 bytes read in 2 ms (52.7 KiB/s)
## Error: Can't overwrite "ethaddr"
himport_r: can't insert "ethaddr=00:50:43:84:fb:2f" into hash table
73474 bytes read in 6 ms (11.7 MiB/s)
26405376 bytes read in 1130 ms (22.3 MiB/s)
libfdt fdt_getprop(): FDT_ERR_NOTFOUND
Mainline bootargs: root=/dev/mmcblk1p1 ro rootwait rootfstype=ext4 init=/sbin/init console=ttyAML0,115200n8 console=tty1 consoleblank=0 coherent_pool=2M loglevel=8 usb-storage.quirks=
9355175 bytes read in 402 ms (22.2 MiB/s)
## Loading init Ramdisk from Legacy Image at 13000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    9355111 Bytes = 8.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 04080000
   Booting using the fdt blob at 0x4080000
   Loading Ramdisk to 3f714000, end 3fffff67 ... OK
   Loading Device Tree to 000000003f699000, end 000000003f713fff ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.16.14 (root@firefly-rk3399) (gcc (GCC) 11.2.0, GNU ld version 2.37-slack15) #1 SMP PREEMPT Fri Mar 11 20:17:10 EET 2022
[    0.000000] Machine model: Radxa Zero
[    0.000000] efi: UEFI not found.
[    0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'secmon@5000000': base 0x0000000005000000, size 3 MiB
[    0.000000] Reserved memory: created CMA memory pool at 0x00000000bcc00000, size 896 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000000f4d97fff]
[    0.000000] NUMA: NODE_DATA [mem 0xbc597040-0xbc598fff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x00000000f4d97fff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x00000000052fffff]
[    0.000000]   node   0: [mem 0x0000000005300000-0x00000000072fffff]
[    0.000000]   node   0: [mem 0x0000000007300000-0x00000000f4d97fff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000f4d97fff]
[    0.000000] On node 0, zone DMA: 12904 pages in unavailable ranges
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] percpu: Embedded 20 pages/cpu s43800 r8192 d29928 u81920
[    0.000000] pcpu-alloc: s43800 r8192 d29928 u81920 alloc=20*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] Fallback order for Node 0: 0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 987233
[    0.000000] Policy zone: DMA
[    0.000000] Kernel command line: root=/dev/mmcblk1p1 ro rootwait rootfstype=ext4 init=/sbin/init console=ttyAML0,115200n8 console=tty1 consoleblank=0 coherent_pool=2M loglevel=8 usb-storage.quirks=
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000] Memory: 2944472K/4011616K available (14912K kernel code, 1786K rwdata, 5648K rodata, 3328K init, 604K bss, 149640K reserved, 917504K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[    0.000000]  Trampoline variant of Tasks RCU enabled.
[    0.000000]  Rude variant of Tasks RCU enabled.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] random: get_random_bytes called from start_kernel+0x4c0/0x6b4 with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000186] Console: colour dummy device 80x25
[    0.000594] printk: console [tty1] enabled
[    0.000670] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.000695] pid_max: default: 32768 minimum: 301
[    0.000757] LSM: Security Framework initializing
[    0.000787] Yama: becoming mindful.
[    0.000891] AppArmor: AppArmor initialized
[    0.000947] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.000980] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.002605] rcu: Hierarchical SRCU implementation.
[    0.004650] EFI services will not be available.
[    0.005016] smp: Bringing up secondary CPUs ...
[    0.005549] Detected VIPT I-cache on CPU1
[    0.005618] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.006166] Detected VIPT I-cache on CPU2
[    0.006197] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.006690] Detected VIPT I-cache on CPU3
[    0.006718] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.006775] smp: Brought up 1 node, 4 CPUs
[    0.006835] SMP: Total of 4 processors activated.
[    0.006846] CPU features: detected: 32-bit EL0 Support
[    0.006856] CPU features: detected: 32-bit EL1 Support
[    0.006868] CPU features: detected: CRC32 instructions
[    0.013978] CPU: All CPU(s) started at EL2
[    0.014058] alternatives: patching kernel code
[    0.015981] devtmpfs: initialized
[    0.026444] Registered cp15_barrier emulation handler
[    0.026487] Registered setend emulation handler
[    0.026651] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.026694] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.050443] pinctrl core: initialized pinctrl subsystem
[    0.051105] DMI not present or invalid.
[    0.051538] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.053880] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations
[    0.054615] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.055962] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.056070] audit: initializing netlink subsys (disabled)
[    0.056278] audit: type=2000 audit(0.052:1): state=initialized audit_enabled=0 res=1
[    0.057659] thermal_sys: Registered thermal governor 'fair_share'
[    0.057666] thermal_sys: Registered thermal governor 'bang_bang'
[    0.057680] thermal_sys: Registered thermal governor 'step_wise'
[    0.057692] thermal_sys: Registered thermal governor 'user_space'
[    0.058370] cpuidle: using governor menu
[    0.058639] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.058747] ASID allocator initialised with 65536 entries
[    0.059850] Serial: AMBA PL011 UART driver
[    0.073733] platform ff900000.vpu: Fixing up cyclic dependency with ff600000.hdmi-tx
[    0.078179] platform hdmi-connector: Fixing up cyclic dependency with ff600000.hdmi-tx
[    0.087999] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.088038] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.088051] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.088064] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.088613] cryptd: max_cpu_qlen set to 1000
[    0.156972] raid6: neonx8   gen()  2144 MB/s
[    0.225036] raid6: neonx8   xor()  1585 MB/s
[    0.293092] raid6: neonx4   gen()  2199 MB/s
[    0.361156] raid6: neonx4   xor()  1558 MB/s
[    0.429226] raid6: neonx2   gen()  2042 MB/s
[    0.497277] raid6: neonx2   xor()  1431 MB/s
[    0.565361] raid6: neonx1   gen()  1782 MB/s
[    0.633426] raid6: neonx1   xor()  1214 MB/s
[    0.701488] raid6: int64x8  gen()  1364 MB/s
[    0.769559] raid6: int64x8  xor()   772 MB/s
[    0.837678] raid6: int64x4  gen()  1602 MB/s
[    0.905694] raid6: int64x4  xor()   849 MB/s
[    0.973776] raid6: int64x2  gen()  1397 MB/s
[    1.041832] raid6: int64x2  xor()   750 MB/s
[    1.109927] raid6: int64x1  gen()  1033 MB/s
[    1.177974] raid6: int64x1  xor()   517 MB/s
[    1.177986] raid6: using algorithm neonx4 gen() 2199 MB/s
[    1.177997] raid6: .... xor() 1558 MB/s, rmw enabled
[    1.178007] raid6: using neon recovery algorithm
[    1.178479] ACPI: Interpreter disabled.
[    1.179665] iommu: Default domain type: Translated
[    1.179687] iommu: DMA domain TLB invalidation policy: strict mode
[    1.179864] vgaarb: loaded
[    1.180526] SCSI subsystem initialized
[    1.180736] usbcore: registered new interface driver usbfs
[    1.180783] usbcore: registered new interface driver hub
[    1.180820] usbcore: registered new device driver usb
[    1.181032] pps_core: LinuxPPS API ver. 1 registered
[    1.181044] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.181070] PTP clock support registered
[    1.181203] EDAC MC: Ver: 3.0.0
[    1.182642] NetLabel: Initializing
[    1.182665] NetLabel:  domain hash size = 128
[    1.182676] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    1.182743] NetLabel:  unlabeled traffic allowed by default
[    1.183160] clocksource: Switched to clocksource arch_sys_counter
[    1.183437] VFS: Disk quotas dquot_6.6.0
[    1.183497] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.184039] AppArmor: AppArmor Filesystem Enabled
[    1.184126] pnp: PnP ACPI: disabled
[    1.189783] NET: Registered PF_INET protocol family
[    1.190044] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    1.191722] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[    1.191880] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    1.192209] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
[    1.192612] TCP: Hash tables configured (established 32768 bind 32768)
[    1.192852] MPTCP token hash table entries: 4096 (order: 4, 98304 bytes, linear)
[    1.192996] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[    1.193095] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[    1.193302] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    1.193343] PCI: CLS 0 bytes, default 64
[    1.193646] Trying to unpack rootfs image as initramfs...
[    1.199870] kvm [1]: IPA Size Limit: 40 bits
[    1.201004] kvm [1]: vgic interrupt IRQ9
[    1.201170] kvm [1]: Hyp mode initialized successfully
[    1.203041] Initialise system trusted keyrings
[    1.203123] Key type blacklist registered
[    1.203314] workingset: timestamp_bits=44 max_order=20 bucket_order=0
[    1.208261] zbud: loaded
[    1.209529] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.210262] fuse: init (API version 7.35)
[    1.211413] integrity: Platform Keyring initialized
[    1.247893] xor: measuring software checksum speed
[    1.252147]    8regs           :  2363 MB/sec
[    1.255739]    32regs          :  2798 MB/sec
[    1.260071]    arm64_neon      :  2320 MB/sec
[    1.260110] xor: using function: 32regs (2798 MB/sec)
[    1.260131] Key type asymmetric registered
[    1.260143] Asymmetric key parser 'x509' registered
[    1.260395] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[    1.260638] io scheduler mq-deadline registered
[    1.260655] io scheduler kyber registered
[    1.260849] io scheduler bfq registered
[    1.261844] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[    1.270703] EINJ: ACPI disabled.
[    1.278341] soc soc0: Amlogic Meson G12A (S905Y2) Revision 28:b (30:2) Detected
[    1.321979] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[    1.325228] Serial: AMBA driver
[    1.325659] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 21, base_baud = 1500000) is a meson_uart
[    1.599619] Freeing initrd memory: 9132K
[    1.605456] printk: console [ttyAML0] enabled
[    2.359883] ffd24000.serial: ttyAML6 at MMIO 0xffd24000 (irq = 26, base_baud = 1500000) is a meson_uart
[    2.368447] serial serial0: tty port ttyAML6 registered
[    2.382973] loop: module loaded
[    2.390794] tun: Universal TUN/TAP device driver, 1.6
[    2.391747] thunder_xcv, ver 1.0
[    2.393472] thunder_bgx, ver 1.0
[    2.396714] nicpf, ver 1.0
[    2.399835] e1000e: Intel(R) PRO/1000 Network Driver
[    2.404227] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    2.410146] igb: Intel(R) Gigabit Ethernet Network Driver
[    2.415433] igb: Copyright (c) 2007-2014 Intel Corporation.
[    2.421004] igbvf: Intel(R) Gigabit Virtual Function Network Driver
[    2.427163] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    2.433223] sky2: driver version 1.30
[    2.437157] VFIO - User Level meta-driver version: 0.3
[    2.443293] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.448242] ehci-pci: EHCI PCI platform driver
[    2.452664] ehci-platform: EHCI generic platform driver
[    2.458031] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.463918] ohci-pci: OHCI PCI platform driver
[    2.468351] ohci-platform: OHCI generic platform driver
[    2.473953] usbcore: registered new interface driver usb-storage
[    2.480914] mousedev: PS/2 mouse device common for all mice
[    2.485599] i2c_dev: i2c /dev entries driver
[    2.496845] sdhci: Secure Digital Host Controller Interface driver
[    2.497408] sdhci: Copyright(c) Pierre Ossman
[    2.501984] Synopsys Designware Multimedia Card Interface Driver
[    2.508338] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.508898] meson-gx-mmc ffe05000.sd: Got CD GPIO
[    2.518014] ledtrig-cpu: registered to indicate activity on CPUs
[    2.525239] meson-sm: secure-monitor enabled
[    2.528564] hid: raw HID events driver (C) Jiri Kosina
[    2.533335] usbcore: registered new interface driver usbhid
[    2.538730] usbhid: USB HID core driver
[    2.544324] NET: Registered PF_INET6 protocol family
[    2.547218] gpio irq setup: hwirq: 0x3B irqfirst: 0x35 irqlast: 0x3C pin[47]
[    2.548416] Segment Routing with IPv6
[    2.554563] genirq: Setting trigger mode 3 for irq 34 failed (meson_gpio_irq_set_type+0x0/0x100)
[    2.558064] In-situ OAM (IOAM) with IPv6
[    2.570705] NET: Registered PF_PACKET protocol family
[    2.575745] 8021q: 802.1Q VLAN Support v1.8
[    2.579829] Key type dns_resolver registered
[    2.584620] registered taskstats version 1
[    2.588074] Loading compiled-in X.509 certificates
[    2.594934] Loaded X.509 cert 'Build time autogenerated kernel key: 69f06163094b30e4d1e1afe58ceda55ca52a0360'
[    2.604777] zswap: loaded using pool zstd/z3fold
[    2.606606] mmc1: new high speed SDXC card at address 5048
[    2.613376] Key type ._fscrypt registered
[    2.613549] mmcblk1: mmc1:5048 SD64G 58.0 GiB
[    2.616622] Key type .fscrypt registered
[    2.623747]  mmcblk1: p1
[    2.624891] Key type fscrypt-provisioning registered
[    2.633995] Btrfs loaded, crc32c=crc32c-generic, zoned=yes, fsverity=yes
[    2.639339] Key type encrypted registered
[    2.642919] AppArmor: AppArmor sha1 policy hashing enabled
[    2.668320] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2
[    2.668391] dwc3-meson-g12a ffe09000.usb: USB3 ports: 1
[    2.676204] dwc2 ff400000.usb: supply vusb_d not found, using dummy regulator
[    2.680309] dwc2 ff400000.usb: supply vusb_a not found, using dummy regulator
[    2.687474] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM
[    2.695386] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    2.699741] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    2.707403] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000000000010010
[    2.716629] xhci-hcd xhci-hcd.0.auto: irq 36, io mem 0xff500000
[    2.722655] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.16
[    2.730654] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.737808] usb usb1: Product: xHCI Host Controller
[    2.742636] usb usb1: Manufacturer: Linux 5.16.14 xhci-hcd
[    2.748070] usb usb1: SerialNumber: xhci-hcd.0.auto
[    2.753260] hub 1-0:1.0: USB hub found
[    2.756638] hub 1-0:1.0: 2 ports detected
[    2.760853] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    2.766023] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    2.773610] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    2.780108] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.788173] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.16
[    2.796290] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.803445] usb usb2: Product: xHCI Host Controller
[    2.808273] usb usb2: Manufacturer: Linux 5.16.14 xhci-hcd
[    2.813707] usb usb2: SerialNumber: xhci-hcd.0.auto
[    2.818912] hub 2-0:1.0: USB hub found
[    2.822273] hub 2-0:1.0: 1 port detected
[    2.827906] meson-gx-mmc ffe03000.sd: allocated mmc-pwrseq
[    2.830497] meson-gx-mmc ffe07000.mmc: allocated mmc-pwrseq
[    2.864741] Freeing unused kernel memory: 3328K
[    2.895203] Run /init as init process
[    2.895295]   with arguments:
[    2.896235]     /init
[    2.898477]   with environment:
[    2.901595]     HOME=/
[    2.904065]     TERM=linux
[    2.982681] random: fast init done
[    2.989289] random: udevd: uninitialized urandom read (16 bytes read)
[    2.990373] random: udevd: uninitialized urandom read (16 bytes read)
[    2.996521] random: udevd: uninitialized urandom read (16 bytes read)
[    2.999872] mmc0: new ultra high speed SDR50 SDIO card at address 0001
[    3.014550] udevd[1189]: starting eudev-3.2.11
[    3.017714] mmc2: new HS200 MMC card at address 0001
[    3.020107] mmcblk2: mmc2:0001 SLD64G 57.6 GiB
[    3.030252] mmc1: card 5048 removed
[    3.032259] udevd[1191]: inotify_add_watch(5, /dev/mmcblk1, 10) failed: No such file or directory
[    3.038169] udevd[1208]: inotify_add_watch(5, /dev/mmcblk1p1, 10) failed: No such file or directory
[    3.052389] mmcblk2boot0: mmc2:0001 SLD64G 4.00 MiB
[    3.054654] mmcblk2boot1: mmc2:0001 SLD64G 4.00 MiB
[    3.058597] mmcblk2rpmb: mmc2:0001 SLD64G 4.00 MiB, chardev (242:0)
[    3.074863] SGI XFS with ACLs, security attributes, realtime, quota, no debug enabled
[    3.087809] device-mapper: uevent: version 1.0.3
[    3.088144] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com
[    5.124984] urandom_read: 4 callbacks suppressed
[    5.124998] random: vgchange: uninitialized urandom read (4 bytes read)