installation of 18.06.2 serialprint

[04050C0A][04050C0C]
DDR Calibration DQS reg = 00008887


U-Boot 1.1.3 (Dec  6 2016 - 11:20:23)

Board: Ralink APSoC
DRAM:  128 MB
relocate_code Pointer at: 87f68000
flash manufacture id: c2, device id 20 19
find flash: MX25L25635E
============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 1024 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: SPI Flash
Date:Dec  6 2016  Time:11:20:23
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =128 Mbytes
RESET MT7628 PHY!!!!!!

GPIOMODE --> 50054404

GPIOMODE2 --> 5540551

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
 2
You choosed 5

 0


5: System Load Linux then write to Flash via USB Storage.
(Re)start USB...
USB0:   *********ehci_hcd_init**********
Mediatek/Ralink USB EHCI host init hccr b01c0000 and hcor b01c0010 hc_length 16
 6. u2phydcr0(0xb0120860)=0x00aaaa02
 FM_OUT value: u4FmOut = 0(0x00000000)
 FM_OUT value: u4FmOut = 133(0x00000085)
 FM detection done! loop = 1
 SR calibration value u1SrCalVal = 6


Register 1111 NbrPorts 1
USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
reading lks7688.img

......................................................................

3932351 bytes read
writing lks7688.img to flash
............................................................
............................................................
.
.
Done!
     [04050C0A][04050C0C]
DDR Calibration DQS reg = 00008887


U-Boot 1.1.3 (Dec  6 2016 - 11:20:23)

Board: Ralink APSoC
DRAM:  128 MB
relocate_code Pointer at: 87f68000
******************************
Software System Reset Occurred
******************************
flash manufacture id: c2, device id 20 19
find flash: MX25L25635E
============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 1024 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: SPI Flash
Date:Dec  6 2016  Time:11:20:23
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =128 Mbytes
RESET MT7628 PHY!!!!!!

GPIOMODE --> 50054404

GPIOMODE2 --> 5540551

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
 0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.95
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1438137 Bytes =  1.4 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 128

Starting kernel ...

[    0.000000] Linux version 4.14.95 (buildbot@builds-03.infra.lede-project.org) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7552-2f11a9e)) #0 Mon Jan 28 08:54:32 2019
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[    0.000000] MIPS: machine is MediaTek LinkIt Smart 7688
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from 0x8042672c with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS2,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=0004a9ec
[    0.000000] Readback ErrCtl register=0004a9ec
[    0.000000] Memory: 125224K/131072K available (3592K kernel code, 183K rwdata, 464K rodata, 168K init, 206K bss, 5848K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] intc: using register map from devicetree
[    0.000000] CPU Clock: 580MHz
[    0.000000] timer_probe: no matching timers found
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[    0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[    0.015381] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.087588] pid_max: default: 32768 minimum: 301
[    0.096960] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.109921] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.129652] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.149029] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.161132] pinctrl core: initialized pinctrl subsystem
[    0.172698] NET: Registered protocol family 16
[    0.186498] Can't analyze schedule() prologue at 8037dd78
[    0.215311] mt7621_gpio 10000600.gpio: registering 32 gpios
[    0.226524] mt7621_gpio 10000600.gpio: registering 32 gpios
[    0.237660] mt7621_gpio 10000600.gpio: registering 32 gpios
[    0.253542] clocksource: Switched to clocksource MIPS
[    0.264660] NET: Registered protocol family 2
[    0.274204] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.287907] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.300419] TCP: Hash tables configured (established 1024 bind 1024)
[    0.313113] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.324573] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.337188] NET: Registered protocol family 1
[    0.349115] Crashlog allocated RAM at address 0x3f00000
[    0.361011] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.379702] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.391139] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.421093] io scheduler noop registered
[    0.428767] io scheduler deadline registered (default)
[    0.439842] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.455261] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
[    0.473764] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A
[    0.491663] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud = 2500000) is a 16550A
[    0.509007] console [ttyS2] enabled
[    0.509007] console [ttyS2] enabled
[    0.522676] bootconsole [early0] disabled
[    0.522676] bootconsole [early0] disabled
[    0.539161] cacheinfo: Failed to find cpu0 device node
[    0.549373] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.562264] spi-mt7621 10000b00.spi: sys_freq: 193333333
[    0.581113] m25p80 spi0.0: mx25l25635e (32768 Kbytes)
[    0.591226] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.603811] Creating 4 MTD partitions on "spi0.0":
[    0.613300] 0x000000000000-0x000000030000 : "u-boot"
[    0.624155] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.635566] 0x000000040000-0x000000050000 : "factory"
[    0.646513] 0x000000050000-0x000002000000 : "firmware"
[    0.727145] 2 uimage-fw partitions found on MTD device firmware
[    0.738907] 0x000000050000-0x0000001af1f9 : "kernel"
[    0.749682] 0x0000001af1f9-0x000002000000 : "rootfs"
[    0.760376] mtd: device 5 (rootfs) set to be root filesystem
[    0.773140] 1 squashfs-split partitions found on MTD device rootfs
[    0.785446] 0x000000400000-0x000002000000 : "rootfs_data"
[    0.798020] libphy: Fixed MDIO Bus: probed
[    0.817264] rt3050-esw 10110000.esw: link changed 0x00
[    0.829090] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    0.847373] NET: Registered protocol family 10
[    0.860370] Segment Routing with IPv6
[    0.867806] NET: Registered protocol family 17
[    0.876663] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    0.902332] 8021q: 802.1Q VLAN Support v1.8
[    0.912508] mtk-linkit bootstrap: Version  : LINKITS7688
[    0.923094] mtk-linkit bootstrap: Revision : REV3
[    0.932409] mtk-linkit bootstrap: setting up bootstrap latch
[    0.950420] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    0.965368] Freeing unused kernel memory: 168K
[    0.974186] This architecture does not have kernel memory protection.
[    1.787211] init: Console is alive
[    1.794274] init: - watchdog -
[    2.433553] random: fast init done
[    2.770314] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.937420] usbcore: registered new interface driver usbfs
[    2.948447] usbcore: registered new interface driver hub
[    2.959101] usbcore: registered new device driver usb
[    2.975003] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.989637] ehci-platform: EHCI generic platform driver
[    3.010362] phy phy-10120000.usbphy.0: remote usb device wakeup disabled
[    3.023647] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz
[    3.034017] ehci-platform 101c0000.ehci: EHCI Host Controller
[    3.045433] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    3.061240] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    3.093560] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    3.107091] hub 1-0:1.0: USB hub found
[    3.114988] hub 1-0:1.0: 1 port detected
[    3.126041] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.139946] ohci-platform: OHCI generic platform driver
[    3.150659] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[    3.164191] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    3.179994] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    3.258564] hub 2-0:1.0: USB hub found
[    3.266500] hub 2-0:1.0: 1 port detected
[    3.278150] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.303004] init: - preinit -
[    3.827104] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    4.118535] random: procd: uninitialized urandom read (4 bytes read)
[    4.429668] rt3050-esw 10110000.esw: link changed 0x00
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    7.700321] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[    7.748695] urandom-seed: Seed file not found (/etc/urandom.seed)
[    7.904495] procd: - early -
[    7.910304] procd: - watchdog -
[    8.641531] procd: - watchdog -
[    8.648103] procd: - ubus -
[    8.863626] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.039527] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.052688] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.066405] procd: - init -
Please press Enter to activate this console.
[    9.429670] kmodloader: loading kernel modules from /etc/modules.d/*
[    9.531760] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    9.554741] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[    9.570661] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[    9.587140] ip_tables: (C) 2000-2006 Netfilter Core Team
[    9.607089] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[    9.686675] xt_time: kernel timezone is -0000
[    9.758434] mt76_wmac 10300000.wmac: ASIC revision: 76280001
[   10.785603] mt76_wmac 10300000.wmac: Firmware Version: 20151201
[   10.797411] mt76_wmac 10300000.wmac: Build Time: 20151201183641
[   10.823554] mt76_wmac 10300000.wmac: firmware init done
[   11.055372] PPP generic driver version 2.4.2
[   11.143930] NET: Registered protocol family 24
[   11.157055] kmodloader: done loading kernel modules from /etc/modules.d/*
[   12.426766] urandom_read: 5 callbacks suppressed
[   12.426777] random: jshn: uninitialized urandom read (4 bytes read)
[   26.168369] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   26.243194] jffs2_build_filesystem(): unlocking the mtd device...
[   26.243207] done.
[   26.259320] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   26.862355] br-lan: port 1(eth0) entered blocking state
[   26.887610] br-lan: port 1(eth0) entered disabled state
[   26.898319] device eth0 entered promiscuous mode
[   27.088431] br-lan: port 1(eth0) entered blocking state
[   27.098841] br-lan: port 1(eth0) entered forwarding state
[   27.109745] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   27.913672] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[  130.143607] random: crng init done
[  165.768629] done.
[  165.772480] jffs2: notice: (1130) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[  166.035244] overlayfs: upper fs does not support tmpfile.