Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- 00:00.0 Host bridge: Intel Corporation 82946GZ/PL/GL Memory Controller Hub (rev 02)
- Subsystem: Gigabyte Technology Co., Ltd Device 5000
- Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
- Latency: 0
- Capabilities: [e0] Vendor Specific Information: Len=09 <?>
- Kernel modules: intel_agp
- 00:01.0 PCI bridge: Intel Corporation 82946GZ/PL/GL PCI Express Root Port (rev 02) (prog-if 00 [Normal decode])
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 0, Cache Line Size: 32 bytes
- Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
- I/O behind bridge: 00009000-00009fff
- Memory behind bridge: f0000000-f3ffffff
- Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
- Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
- Capabilities: [88] Subsystem: Gigabyte Technology Co., Ltd Device 5000
- Capabilities: [80] Power Management version 3
- Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
- Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
- Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
- Address: fee0f00c Data: 4181
- Capabilities: [a0] Express (v1) Root Port (Slot+), MSI 00
- DevCap: MaxPayload 128 bytes, PhantFunc 0
- ExtTag- RBE+
- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
- MaxPayload 128 bytes, MaxReadReq 128 bytes
- DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
- LnkCap: Port #2, Speed 2.5GT/s, Width x16, ASPM L0s, Exit Latency L0s <256ns, L1 <64us
- ClockPM- Surprise- LLActRep- BwNot-
- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
- Slot #32, PowerLimit 75.000W; Interlock- NoCompl+
- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
- Control: AttnInd Off, PwrInd On, Power- Interlock-
- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
- Changed: MRL- PresDet+ LinkState-
- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
- RootCap: CRSVisible-
- RootSta: PME ReqID 0000, PMEStatus- PMEPending-
- Capabilities: [100 v1] Virtual Channel
- Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
- Arb: Fixed- WRR32- WRR64- WRR128-
- Ctrl: ArbSelect=Fixed
- Status: InProgress-
- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
- Status: NegoPending- InProgress-
- Capabilities: [140 v1] Root Complex Link
- Desc: PortNumber=02 ComponentID=01 EltType=Config
- Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB- LinkType=MemMapped LinkValid+
- Addr: 00000000fed19000
- Kernel driver in use: pcieport
- Kernel modules: shpchp
- 00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])
- Subsystem: Gigabyte Technology Co., Ltd GA-D525TUD
- Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 0
- Interrupt: pin A routed to IRQ 23
- Region 4: I/O ports at bc00 [size=32]
- Kernel driver in use: uhci_hcd
- Kernel modules: uhci_hcd
- 00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])
- Subsystem: Gigabyte Technology Co., Ltd GA-D525TUD
- Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 0
- Interrupt: pin B routed to IRQ 19
- Region 4: I/O ports at b000 [size=32]
- Kernel driver in use: uhci_hcd
- Kernel modules: uhci_hcd
- 00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])
- Subsystem: Gigabyte Technology Co., Ltd GA-D525TUD
- Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 0
- Interrupt: pin C routed to IRQ 18
- Region 4: I/O ports at b400 [size=32]
- Kernel driver in use: uhci_hcd
- Kernel modules: uhci_hcd
- 00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI])
- Subsystem: Gigabyte Technology Co., Ltd GA-D525TUD
- Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 0
- Interrupt: pin D routed to IRQ 16
- Region 4: I/O ports at b800 [size=32]
- Kernel driver in use: uhci_hcd
- Kernel modules: uhci_hcd
- 00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
- Subsystem: Gigabyte Technology Co., Ltd GA-D525TUD
- Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 0
- Interrupt: pin A routed to IRQ 23
- Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=1K]
- Capabilities: [50] Power Management version 2
- Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
- Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
- Kernel driver in use: ehci-pci
- Kernel modules: ehci_pci
- 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 0
- Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
- I/O behind bridge: 0000a000-0000afff
- Memory behind bridge: f4000000-f5ffffff
- Prefetchable memory behind bridge: 0000000080000000-00000000800fffff
- Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
- Capabilities: [50] Subsystem: Gigabyte Technology Co., Ltd Motherboard
- 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
- Subsystem: Gigabyte Technology Co., Ltd Device 5001
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 0
- Capabilities: [e0] Vendor Specific Information: Len=0c <?>
- Kernel driver in use: lpc_ich
- Kernel modules: intel_rng, lpc_ich, leds_ss4200
- 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])
- Subsystem: Gigabyte Technology Co., Ltd Device b001
- Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 0
- Interrupt: pin A routed to IRQ 18
- Region 0: I/O ports at 01f0 [size=8]
- Region 1: I/O ports at 03f4
- Region 2: I/O ports at 0170 [size=8]
- Region 3: I/O ports at 0374
- Region 4: I/O ports at f000 [size=16]
- Kernel driver in use: ata_piix
- Kernel modules: ata_piix, pata_acpi, ata_generic
- 00:1f.2 IDE interface: Intel Corporation NM10/ICH7 Family SATA Controller [IDE mode] (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
- Subsystem: Gigabyte Technology Co., Ltd Device b002
- Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 0
- Interrupt: pin B routed to IRQ 19
- Region 0: I/O ports at d000 [size=8]
- Region 1: I/O ports at d400 [size=4]
- Region 2: I/O ports at d800 [size=8]
- Region 3: I/O ports at dc00 [size=4]
- Region 4: I/O ports at e000 [size=16]
- Capabilities: [70] Power Management version 2
- Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
- Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
- Kernel driver in use: ata_piix
- Kernel modules: ata_piix, pata_acpi, ata_generic
- 00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 01)
- Subsystem: Gigabyte Technology Co., Ltd GA-8I945PG-RH/GA-D525TUD Mainboard
- Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Interrupt: pin B routed to IRQ 19
- Region 4: I/O ports at 0500 [size=32]
- Kernel driver in use: i801_smbus
- Kernel modules: i2c_i801
- 01:00.0 VGA compatible controller: NVIDIA Corporation G96 [GeForce 9400 GT] (rev a1) (prog-if 00 [VGA controller])
- Subsystem: Gigabyte Technology Co., Ltd Device 349b
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 0, Cache Line Size: 32 bytes
- Interrupt: pin A routed to IRQ 41
- Region 0: Memory at f2000000 (32-bit, non-prefetchable) [size=16M]
- Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
- Region 3: Memory at f0000000 (64-bit, non-prefetchable) [size=32M]
- Region 5: I/O ports at 9000 [size=128]
- [virtual] Expansion ROM at f3000000 [disabled] [size=512K]
- Capabilities: [60] Power Management version 3
- Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
- Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
- Capabilities: [68] MSI: Enable+ Count=1/1 Maskable- 64bit+
- Address: 00000000fee0f00c Data: 4191
- Capabilities: [78] Express (v1) Endpoint, MSI 00
- DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
- ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
- MaxPayload 128 bytes, MaxReadReq 512 bytes
- DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <512ns, L1 <1us
- ClockPM- Surprise- LLActRep- BwNot-
- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- CommClk+
- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
- Capabilities: [b4] Vendor Specific Information: Len=14 <?>
- Capabilities: [100 v1] Virtual Channel
- Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
- Arb: Fixed- WRR32- WRR64- WRR128-
- Ctrl: ArbSelect=Fixed
- Status: InProgress-
- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
- Status: NegoPending- InProgress-
- Capabilities: [128 v1] Power Budgeting <?>
- Capabilities: [600 v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
- Kernel driver in use: nouveau
- Kernel modules: nouveau
- 02:00.0 Network controller: Qualcomm Atheros AR9227 Wireless Network Adapter (rev 01)
- Subsystem: Qualcomm Atheros Device 0301
- Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 168, Cache Line Size: 32 bytes
- Interrupt: pin A routed to IRQ 20
- Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=64K]
- Capabilities: [44] Power Management version 2
- Flags: PMEClk- DSI- D1- D2- AuxCurrent=100mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
- Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
- Kernel driver in use: ath9k
- Kernel modules: ath9k
- 02:01.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 04)
- Subsystem: Creative Labs CT4850 SBLive! Value
- Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 32 (500ns min, 5000ns max)
- Interrupt: pin A routed to IRQ 19
- Region 0: I/O ports at a000 [size=32]
- Capabilities: [dc] Power Management version 1
- Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
- Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
- Kernel driver in use: snd_emu10k1
- Kernel modules: snd_emu10k1
- 02:01.1 Input device controller: Creative Labs SB Live! Game Port (rev 01)
- Subsystem: Creative Labs Gameport Joystick
- Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 32
- Region 0: I/O ports at a400 [size=8]
- Capabilities: [dc] Power Management version 1
- Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
- Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
- Kernel driver in use: Emu10k1_gameport
- Kernel modules: emu10k1_gp
- 02:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet (rev 10)
- Subsystem: Gigabyte Technology Co., Ltd GA-MA69G-S3H Motherboard
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
- Interrupt: pin A routed to IRQ 21
- Region 0: I/O ports at a800 [size=256]
- Region 1: Memory at f5010000 (32-bit, non-prefetchable) [size=256]
- [virtual] Expansion ROM at 80000000 [disabled] [size=128K]
- Capabilities: [dc] Power Management version 2
- Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
- Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
- Kernel driver in use: r8169
- Kernel modules: r8169
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement