U-Boot SPL 2018.03-34721-gb399abdade (Oct 21 2019 - 13:57:07 +0200)
Normal Boot
Trying to boot from MMC1


U-Boot 2018.03-34721-gb399abdade (Oct 21 2019 - 13:57:07 +0200)

CPU:   Freescale i.MX8MMQ rev1.0 1800 MHz (running at 1200 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 27C
Reset cause: POR
Model: Variscite DART-MX8MM board
I2C:   ready
DRAM:  2 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial

 BuildInfo:
  - ATF d6451cc
  - U-Boot 2018.03-34721-gb399abdade


Part number: VSM-DT8MM-102
Assembly: AS1904144564
Production date: 2019 Jun 02
Serial Number: f8:dc:7a:2c:90:84
switch to partitions #0, OK
mmc0 is current device
flash target is MMC:0
Net:
ethernet@30be0000 MAC address in ROM is 00:00:00:00:00:00
eth0: ethernet@30be0000
Fastboot: Normal
Normal Boot
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
** File not found /boot/boot.scr **
5250707 bytes read in 340 ms (14.7 MiB/s)
Uncompressed size: 11816968 = 0xB45008
Booting from mmc ...
43286 bytes read in 124 ms (340.8 KiB/s)
## Flattened Device Tree blob at 43000000
   Booting using the fdt blob at 0x43000000
   Using Device Tree in place at 0000000043000000, end 000000004300d915

Starting kernel ...

Booting Linux on physical CPU 0x0
Linux version 4.14.78-g09a8b5955516 (root@titan) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #2 SMP PREEMPT Mon Oct 21 13:57:32 CEST 2019
Boot CPU: AArch64 Processor [410fd034]
Machine model: Variscite DART-MX8MM board
earlycon: ec_imx6q0 at MMIO 0x0000000030860000 (options '115200')
bootconsole [ec_imx6q0] enabled
cma: Reserved 640 MiB at 0x0000000090000000
psci: probing for conduit method from DT.
psci: PSCIv1.1 detected in firmware.
psci: Using standard PSCI v0.2 function IDs
psci: MIGRATE_INFO_TYPE not supported.
psci: SMC Calling Convention v1.1
percpu: Embedded 20 pages/cpu @ffff80007ff6a000 s41752 r8192 d31976 u81920
Detected VIPT I-cache on CPU0
CPU features: enabling workaround for ARM erratum 845719
Speculative Store Bypass Disable mitigation not required
Built 1 zonelists, mobility grouping on.  Total pages: 515072
Kernel command line: console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200 root=/dev/mmcblk1p1 rootwait rw cma=640MB
log_buf_len individual max cpu contribution: 4096 bytes
log_buf_len total cpu_extra contributions: 12288 bytes
log_buf_len min size: 16384 bytes
log_buf_len: 32768 bytes
early log buf free: 14560(88%)
PID hash table entries: 4096 (order: 3, 32768 bytes)
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Memory: 1389312K/2093056K available (7358K kernel code, 852K rwdata, 2764K rodata, 512K init, 267K bss, 48384K reserved, 655360K cma-reserved)
Virtual kernel memory layout:
    modules : 0xffff000000000000 - 0xffff000008000000   (   128 MB)
    vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000   (129022 GB)
      .text : 0xffff000008080000 - 0xffff0000087b0000   (  7360 KB)
    .rodata : 0xffff0000087b0000 - 0xffff000008a70000   (  2816 KB)
      .init : 0xffff000008a70000 - 0xffff000008af0000   (   512 KB)
      .data : 0xffff000008af0000 - 0xffff000008bc5008   (   853 KB)
       .bss : 0xffff000008bc5008 - 0xffff000008c07ee0   (   268 KB)
    fixed   : 0xffff7dfffe7fb000 - 0xffff7dfffec00000   (  4116 KB)
    PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000   (    16 MB)
    vmemmap : 0xffff7e0000000000 - 0xffff800000000000   (  2048 GB maximum)
              0xffff7e0000000000 - 0xffff7e0002000000   (    32 MB actual)
    memory  : 0xffff800000000000 - 0xffff800080000000   (  2048 MB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Preemptible hierarchical RCU implementation.
	RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
	Tasks RCU enabled.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
GICv3: GIC: Using split EOI/Deactivate mode
GICv3: no VLPI support, no direct LPI support
ITS: No ITS available, not enabling LPIs
GICv3: CPU0: found redistributor 0 region 0:0x0000000038880000
i.MX8MM clock driver init done
arch_timer: cp15 timer(s) running at 8.00MHz (phys).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns
sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns
system counter timer init
sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns
clocksource: imx sysctr: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns
Console: colour dummy device 80x25
Calibrating delay loop (skipped), value calculated using timer frequency.. 16.00 BogoMIPS (lpj=32000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
ASID allocator initialised with 32768 entries
Hierarchical SRCU implementation.
Cannot find MU entry in device tree
CPU identified as i.MX8MM, silicon rev 1.0
smp: Bringing up secondary CPUs ...
Detected VIPT I-cache on CPU1
GICv3: CPU1: found redistributor 1 region 0:0x00000000388a0000
CPU1: Booted secondary processor [410fd034]
Detected VIPT I-cache on CPU2
GICv3: CPU2: found redistributor 2 region 0:0x00000000388c0000
CPU2: Booted secondary processor [410fd034]
Detected VIPT I-cache on CPU3
GICv3: CPU3: found redistributor 3 region 0:0x00000000388e0000
CPU3: Booted secondary processor [410fd034]
smp: Brought up 1 node, 4 CPUs
SMP: Total of 4 processors activated.
CPU features: detected feature: GIC system register CPU interface
CPU features: detected feature: 32-bit EL0 Support
CPU features: detected feature: Kernel page table isolation (KPTI)
CPU: All CPU(s) started at EL2
alternatives: patching kernel code
devtmpfs: initialized
random: get_random_u32 called from bucket_table_alloc+0xf8/0x280 with crng_init=0
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
futex hash table entries: 1024 (order: 5, 131072 bytes)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
cpuidle: using governor menu
vdso: 2 pages (1 code @ ffff0000087b6000, 1 data @ ffff000008af4000)
hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
DMA: preallocated 256 KiB pool for atomic allocations
imx8mm-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver
HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
vgaarb: loaded
bd71837 0-004b: Device ID=0xA0
bd71837 0-004b: gpio_intr = 40
bd71837 0-004b: chip_irq=104
bd71837-pmic bd71837-pmic: regulator register name 'buck1'
bd71837-pmic bd71837-pmic: regulator register name 'buck2'
bd71837-pmic bd71837-pmic: regulator register name 'buck3'
bd71837-pmic bd71837-pmic: regulator register name 'buck4'
bd71837-pmic bd71837-pmic: regulator register name 'buck5'
bd71837-pmic bd71837-pmic: regulator register name 'buck6'
bd71837-pmic bd71837-pmic: regulator register name 'buck7'
bd71837-pmic bd71837-pmic: regulator register name 'buck8'
bd71837-pmic bd71837-pmic: regulator register name 'ldo1'
bd71837-pmic bd71837-pmic: regulator register name 'ldo2'
bd71837-pmic bd71837-pmic: regulator register name 'ldo3'
bd71837-pmic bd71837-pmic: regulator register name 'ldo4'
bd71837-pmic bd71837-pmic: regulator register name 'ldo5'
ldo5: Bringing 3300000uV into 1800000-1800000uV
bd71837-pmic bd71837-pmic: regulator register name 'ldo6'
bd71837-pmic bd71837-pmic: regulator register name 'ldo7'
random: fast init done
i2c i2c-0: IMX I2C adapter registered
i2c i2c-0: can't use DMA, using PIO instead.
i2c i2c-1: IMX I2C adapter registered
i2c i2c-1: can't use DMA, using PIO instead.
i2c i2c-2: IMX I2C adapter registered
i2c i2c-2: can't use DMA, using PIO instead.
i2c i2c-3: IMX I2C adapter registered
i2c i2c-3: can't use DMA, using PIO instead.
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
MU is ready for cross core communication!
virtio_rpmsg_bus virtio0: rpmsg host is online
imx rpmsg driver is registered.
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arch_sys_counter
NET: Registered protocol family 2
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
UDP hash table entries: 1024 (order: 3, 32768 bytes)
UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
workingset: timestamp_bits=46 max_order=19 bucket_order=0
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
nfs4filelayout_init: NFSv4 File Layout Driver Registering...
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
io scheduler noop registered
io scheduler cfq registered (default)
io scheduler mq-deadline registered
io scheduler kyber registered
mxs-dma 33000000.dma-apbh: initialized
Bus freq driver module loaded
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 28, base_baud = 1500000) is a IMX
console [ttymxc0] enabled
console [ttymxc0] enabled
bootconsole [ec_imx6q0] disabled
bootconsole [ec_imx6q0] disabled
30880000.serial: ttymxc2 at MMIO 0x30880000 (irq = 29, base_baud = 1500000) is a IMX
30890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 30, base_baud = 1500000) is a IMX
30a60000.serial: ttymxc3 at MMIO 0x30a60000 (irq = 35, base_baud = 5000000) is a IMX
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[drm] No driver support for vblank timestamp query.
imx-drm display-subsystem: bound imx-lcdif-crtc.0 (ops lcdif_crtc_ops)
imx_sec_dsim_drv 32e10000.mipi_dsi: version number is 0x1060200
imx-drm display-subsystem: bound 32e10000.mipi_dsi (ops imx_sec_dsim_ops)
imx-drm display-subsystem: sn65dsi83_connector_mode_valid: mode: 800*480@33000 is valid
sn65dsi83 0-002c: DSI clock [ 396000000 ] Hz
sn65dsi83 0-002c: GeoMetry [ 800 x 480 ] Hz
Console: switching to colour frame buffer device 100x30
imx-drm display-subsystem: fb0:  frame buffer device
[drm] Initialized imx-drm 1.0.0 20120507 for display-subsystem on minor 0
spi_imx 30820000.ecspi: dma setup error -19, use pio
spi_imx 30820000.ecspi: probed
libphy: Fixed MDIO Bus: probed
CAN device driver interface
mcp25xxfd spi0.1: CRC read error: computed: ec03 received: 0000 - data: be 00 04 00 00 00 00
mcp25xxfd spi0.1: CRC read of clock register resulted in a bad CRC mismatch - hw not found
mcp25xxfd spi0.1: Probe failed, err=84
mcp25xxfd: probe of spi0.1 failed with error -84
input: 30370000.snvs:snvs-powerkey as /devices/platform/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0
edt_ft5x06 1-0038: touchscreen probe failed
i2c /dev entries driver
IR NEC protocol handler initialized
IR RC5(x/sz) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
IR SANYO protocol handler initialized
IR Sharp protocol handler initialized
IR MCE Keyboard/mouse protocol handler initialized
IR XMP protocol handler initialized
mxc_mipi-csi 32e30000.mipi_csi: 32e30000.mipi_csi supply mipi-phy not found, using dummy regulator
mxc_mipi-csi 32e30000.mipi_csi: mipi csi v4l2 device registered
CSI: Registered sensor subdevice: mxc_mipi-csi.0
mxc_mipi-csi 32e30000.mipi_csi: lanes: 2, hs_settle: 13, clk_settle: 2, wclk: 1, freq: 333000000
imx2-wdt 30280000.wdog: timeout 60 sec (nowayout=0)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA
sdhci-esdhc-imx 30b50000.mmc: Got CD GPIO
mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA
mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA
galcore: clk_get vg clock failed, disable vg!
Galcore version 6.2.4.163672
hantrodec 0 : module inserted. Major = 244
hantrodec 1 : module inserted. Major = 244
hx280enc: module inserted. Major <243>
mmc2: new HS400 MMC card at address 0001
ledtrig-cpu: registered to indicate activity on CPUs
mmcblk2: mmc2:0001 AJTD4R 14.6 GiB
mmcblk2boot0: mmc2:0001 AJTD4R partition 1 4.00 MiB
mmcblk2boot1: mmc2:0001 AJTD4R partition 2 4.00 MiB
mmcblk2rpmb: mmc2:0001 AJTD4R partition 3 4.00 MiB
 mmcblk2: p1
mmc1: host does not support reading read-only switch, assuming write-enable
caam 30900000.caam: ERA source: CCBVID.
caam 30900000.caam: device ID = 0x0a16040100000000 (Era 9)
caam 30900000.caam: job rings = 3, qi = 0, dpaa2 = no
caam_jr 30901000.jr0: Entropy delay = 3200
caam_jr 30901000.jr0: Entropy delay = 3600
caam_jr 30901000.jr0: Instantiated RNG4 SH0.
mmc1: new ultra high speed SDR104 SDHC card at address 59b4
mmcblk1: mmc1:59b4 USDU1 14.9 GiB
 mmcblk1: p1
caam_jr 30901000.jr0: Instantiated RNG4 SH1.
caam algorithms registered in /proc/crypto
caam_jr 30901000.jr0: registering rng-caam
caam 30900000.caam: caam pkc algorithms registered in /proc/crypto
wm8904 2-001a: revision A
fsl-asoc-card sound-wm8904: wm8904-hifi <-> 30030000.sai mapping ok
NET: Registered protocol family 17
can: controller area network core (rev 20170425 abi 9)
NET: Registered protocol family 29
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
cpu cpu0: registered imx8mq-cpufreq
imx6q-pcie 33800000.pcie: 33800000.pcie supply epdev_on not found, using dummy regulator
OF: PCI: host bridge /pcie@0x33800000 ranges:
OF: PCI:   No bus range found for /pcie@0x33800000, using [bus 00-ff]
OF: PCI:    IO 0x1ff80000..0x1ff8ffff -> 0x00000000
OF: PCI:   MEM 0x18000000..0x1fefffff -> 0x18000000
imx6q-pcie 33800000.pcie: Initialize PHY with EXT REfCLK!.
imx6q-pcie 33800000.pcie: PHY Initialization End!.
imx6q-pcie 33800000.pcie: pcie phy pll can't be locked.
imx6q-pcie 33800000.pcie: failed to initialize host
imx6q-pcie 33800000.pcie: unable to add pcie port.
hctosys: unable to open rtc device (rtc0)
eth_phy_pwr: disabling
WIFI_REG_ON: disabling
ALSA device list:
  #0: wm8904-audio
EXT4-fs (mmcblk1p1): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 179:129.
devtmpfs: mounted
Freeing unused kernel memory: 512K
systemd[1]: System time before build time, advancing clock.
systemd[1]: Inserted module 'autofs4'
NET: Registered protocol family 10
Segment Routing with IPv6
ip_tables: (C) 2000-2006 Netfilter Core Team
systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
systemd[1]: Detected architecture arm64.

Welcome to Debian GNU/Linux 10 (buster)!

systemd[1]: Set hostname to <imx8mm-var-dart>.
systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
systemd[1]: /lib/systemd/system/pulseaudio.service:5: PIDFile= references path below legacy directory /var/run/, updating /var/run/pulse/pid → /run/pulse/pid; please update the unit file accordingly.
random: systemd: uninitialized urandom read (16 bytes read)
random: systemd: uninitialized urandom read (16 bytes read)
systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[  OK  ] Started Dispatch Password …ts to Console Directory Watch.
random: systemd: uninitialized urandom read (16 bytes read)
systemd[1]: Listening on Syslog Socket.
[  OK  ] Listening on Syslog Socket.
systemd[1]: Listening on Journal Socket.
[  OK  ] Listening on Journal Socket.
systemd[1]: Starting Load Kernel Modules...
         Starting Load Kernel Modules...
         Mounting POSIX Message Queue File System...
         Starting Set the console keyboard layout...
         Mounting Huge Pages Filgpio_bb: loading out-of-tree module taints kernel.
e System...
gpio-bb: gpio bit-bang driver version 1.3 ready.
         Mounting RPC Pipe File System...
[  OK  ] Reached target System Time Synchronized.
[  OK  ] Listening on Journal Socket (/dev/log).
[  OK  ] Created slice User and Session Slice.
[  OK  ] Reached target Slices.
[  OK  ] Created slice system-getty.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
[  OK  ] Listening on initctl Compatibility Named Pipe.
         Starting Remount Root and Kernel File Systems...
         Mounting Kernel Debug File System...
[  OK  ] Listening on udev Control Socket.
         Starting Create list of re…odes for the current kernel...
[  OK  ] Listening on RPCbind Server Activation Socket.
[  OK  ] Reached target Swap.
         Starting Journal Service...
[  OK  ] Started Forward Password R…uests to Wall Directory Watch.
[  OK  ] Reached target Local Encrypted Volumes.
[  OK  ] Listening on udev Kernel Socket.
         Starting udev Coldplug all Devices...
[  OK  ] Started Journal Service.
[  OK  ] Started Load Kernel Modules.
[  OK  ] Mounted POSIX Message Queue File System.
[  OK  ] Started Set the console keyboard layout.
[  OK  ] Mounted Huge Pages File System.
[  OK  ] Mounted RPC Pipe File System.
[  OK  ] Started Remount Root and Kernel File Systems.
[  OK  ] Mounted Kernel Debug File System.
[  OK  ] Started Create list of req… nodes for the current kernel.
         Starting Load/Save Random Seed...
         Starting Create System Users...
         Mounting Kernel Configuration File System...
         Starting Apply Kernel Variables...
         Starting Flush Journal to Persistent Storage...
[  OK  ] Started udev Coldplug all Devices.
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Started Create System Users.
[  OK  ] Mounted Kernel Configuration File System.
[  OK  ] Started Apply Kernel Variables.
         Starting Create Static Device Nodes in /dev...
         Starting Helper to synchronize boot up for ifupdown...
systemd-journald[210]: Received request to flush runtime journal from PID 1
[  OK  ] Started Flush Journal to Persistent Storage.
[  OK  ] Started Create Static Device Nodes in /dev.
[  OK  ] Reached target Local File Systems (Pre).
[  OK  ] Reached target Local File Systems.
         Starting Set console font and keymap...
         Starting Create Volatile Files and Directories...
         Starting Preprocess NFS configuration...
         Starting udev Kernel Device Manager...
[  OK  ] Started Set console font and keymap.
[  OK  ] Started Preprocess NFS configuration.
[  OK  ] Reached target NFS client services.
[  OK  ] Started Create Volatile Files and Directories.
         Starting Update UTMP about System Boot/Shutdown...
         Starting RPC bind portmap service...
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[  OK  ] Started RPC bind portmap service.
[  OK  ] Reached target RPC Port Mapper.
[  OK  ] Reached target Remote File Systems (Pre).
[  OK  ] Reached target Remote File Systems.
[  OK  ] Started udev Kernel Device Manager.
[  OK  ] Reached target System Initialization.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Reached target Sockets.
[  OK  ] Started Daily apt download activities.
[  OK  ] Started Daily rotation of log files.
[  OK  ] Started local-apt-repository.pathimx-sdma 30bd0000.dma-controller: no iram assigned, using external mem
.
imx-sdma 302c0000.dma-controller: no iram assigned, using external mem
[  OK  ] Reached targetimx-sdma 302b0000.dma-controller: no iram assigned, using external mem
 Paths.
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Started Daily apt upgrade and clean activities.
[  OK  ] Reached target Timers.
[  OK  ] Reached target Basic System.
imx-sdma 30bd0000.dma-controller: loaded firmware 4.4
imx-sdma 302c0000.dma-controller: loaded firmware 4.4
imx-sdma 302b0000.dma-controller: loaded firmware 4.4
         Starting Bluetooth OBEX service...
         Starting Login Service...
         Starting Restore /etc/reso… the ppp link was shut down...
         Starting PulseAudio system server...
usbmisc_imx 32e40200.usbmisc: 32e40200.usbmisc supply vbus-wakeup not found, using dummy regulator
usbmisc_imx 32e50200.usbmisc: 32e50200.usbmisc supply vbus-wakeup not found, using dummy regulator
input: gpio-keys as /devices/platform/gpio-keys/input/input2
usb_phy_generic usbphynop1: usbphynop1 supply vcc not found, using dummy regulator
usb_phy_generic usbphynop2: usbphynop2 supply vcc not found, using dummy regulator
         Starting Modem Manager...
         Starting LSB: Start busybox udhcpd at boot time...
ov5640_mipi 1-003c: 1-003c supply DOVDD not found, using dummy regulator
pps pps0: new PPS source ptp0
[  OK  ] ov5640_mipi 1-003c: 1-003c supply DVDD not found, using dummy regulator
Started D-Bus System Mesov5640_mipi 1-003c: 1-003c supply AVDD not found, using dummy regulator
sage Bus.
libphy: fec_enet_mii_bus: probed
fec 30be0000.ethernet eth0: registered PHC device 0
         Starting Network Manager...
         Starting System Logging Service...
ov5640_mipi 1-003c: Read reg error: reg=300a
ov5640_mipi 1-003c: Camera is not found
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
[  OK  ] Started Regular background program processing daemon.
         Starting rng-tools.service...
         Starting WPA supplicant...
         Starting Variscite WIFI setup service...
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[  OK  ] Started Restore /etc/resol…re the ppp link was shut down.
[  OK  ] Found device /dev/ttymxc0.
random: crng init done
random: 7 urandom warning(s) missed due to ratelimiting
[  OK  ] Started rng-tools.service.
imx_usb 32e40000.usb: 32e40000.usb supply vbus not found, using dummy regulator
imx_usb 32e50000.usb: 32e50000.usb supply vbus not found, using dummy regulator
ci_hdrc ci_hdrc.1: EHCI Host Controller
ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
EXT4-fs (mmcblk2p1): mounted filesystem with ordered data mode. Opts: errors=remount-ro
[  OK  ] Started System Logging Service.
[  OK  ] Started LSB: Start busybox udhcpd at boot time.
[  OK  ] Started Manage Sound Card State (restore and store).
         Starting Save/Restore Sound Card State...
mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA
mmc0: queuing unknown CIS tuple 0x80 (2 bytes)
mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
[  OK  ] Started Login Service.
[  OK  ] Started Bluetooth OBEX service.
[  OK  ] Started WPA supplicant.
mmc0: new ultra high speed SDR104 SDIO card at address 0001
brcmfmac: brcmf_fw_map_chip_to_name: using brcm/brcmfmac4339-sdio.bin for chip 0x004339(17209) rev 0x000002
[  OK  ] Started Save/Restore Sound Card State.
         Starting Authorization Manager...
[  OK  ] Reached target Sound Card.
[  OK  ] Started Helper to synchronize boot up for ifupdown.
         Starting Raise network interfaces...
[  OK  ] Started Authorization Manager.
[  OK  ] Started Network Manager.
         Starting Hostname Service...
[  OK  ] Started Modem Manager.
brcmfmac mmc0:0001:1: Falling back to user helper
brcmfmac: brcmf_c_process_clm_blob: no clm_blob available(err=-11), device may have limited channels available
brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Jun 26 2018 01:58:05 version 6.37.39.94 (r692107 CY)
Atheros 8031 ethernet 30be0000.ethernet-1:00: attached PHY driver [Atheros 8031 ethernet] (mii_bus:phy_addr=30be0000.ethernet-1:00, irq=POLL)
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[  OK  ] Started Raise network interfaces.
[  OK  ] Started Hostname Service.
         Starting Network Manager Script Dispatcher Service...
[  OK  ] Started Network Manager Script Dispatcher Service.
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  OK  ] Started PulseAudio system server.
[  OK  ] Started Variscite WIFI setup service.
[  OK  ] Reached target Network.
         Starting Network Time Service...
         Starting OpenBSD Secure Shell server...
         Starting /etc/rc.local Compatibility...
         Starting Permit User Sessions...
         Starting Variscite Bluetooth setup service...
[  OK  ] Started Network Time Service.
[  OK  ] Started /etc/rc.local Compatibility.
[  OK  ] Started Permit User Sessions.
         Starting Weston Wayland Compositor (on tty7)...
[  OK  ] Started Pv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
;39mSerial Getty on ttymxc0.
[  OK  ] Started Getty on tty1.
[  OK  ] Reached target Login Prompts.
[  OK  ] Started Weston Wayland Compositor (on tty7).
[  OK  ] Started OpenBSD Secure Shell server.
[  OK  ] Created slice User Slice of UID 0.
         Starting User Runtime Directory /run/user/0...
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  OK  ] Started User Runtime Directory /run/user/0.
         Starting User Manager for UID 0...
[  OK  ] Started User Manager for UID 0.
[  OK  ] Started Session c1 of user root.
imx-drm display-subsystem: sn65dsi83_connector_mode_valid: mode: 800*480@33000 is valid
[  OK  ] Started Variscite Bluetooth setup service.
[  OK  ] Reached target Multi-User System.
[  OK  ] Reached target Graphical Interface.
         Starting Update UTMP about System Runlevel Changes...
[  OK  ] Started Update UTMP about System Runlevel Changes.

__      __        _          _ _
\ \    / /       (_)        (_) |
 \ \  / /_ _ _ __ _ ___  ___ _| |_ ___
  \ \/ / _` | '__| / __|/ __| | __/ _ \
   \  / (_| | |  | \__ \ (__| | ||  __/
    \/ \__,_|_|  |_|___/\___|_|\__\___|

          2019 Variscite, Ltd.

imx8mm-var-dart login: fec 30be0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Bluetooth: Core ver 2.22
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Bluetooth: HCI UART driver ver 2.3
Bluetooth: HCI UART protocol H4 registered
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: BNEP socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11