Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- # hostapd -dd /etc/hostapd.conf
- random: Trying to read entropy from /dev/random
- Configuration file: /etc/hostapd.conf
- Line 49: DEPRECATED: 'dump_file' configuration variable is not used anymore
- ctrl_interface_group=0
- rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
- nl80211: Supported cipher 00-0f-ac:1
- nl80211: Supported cipher 00-0f-ac:5
- nl80211: Supported cipher 00-0f-ac:2
- nl80211: Supported cipher 00-0f-ac:4
- nl80211: Supported cipher 00-0f-ac:10
- nl80211: Supported cipher 00-0f-ac:8
- nl80211: Supported cipher 00-0f-ac:9
- nl80211: Supported cipher 00-0f-ac:6
- nl80211: Supported cipher 00-0f-ac:13
- nl80211: Supported cipher 00-0f-ac:11
- nl80211: Supported cipher 00-0f-ac:12
- nl80211: Using driver-based off-channel TX
- nl80211: interface wlx74da38e18cfb in phy phy0
- nl80211: Set mode ifindex 3 iftype 3 (AP)
- nl80211: Setup AP(wlx74da38e18cfb) - device_ap_sme=0 use_monitor=0
- nl80211: Subscribe to mgmt frames with AP handle 0x5556f1467100
- nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x5556f1467100 match=
- nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ) nl_handle=0x5556f1467100 match=
- nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ) nl_handle=0x5556f1467100 match=
- nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC) nl_handle=0x5556f1467100 match=
- nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH) nl_handle=0x5556f1467100 match=
- nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5556f1467100 match=
- nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ) nl_handle=0x5556f1467100 match=
- nl80211: Add own interface ifindex 3
- nl80211: if_indices[16]: 3
- phy: phy0
- BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
- wlx74da38e18cfb: interface state UNINITIALIZED->COUNTRY_UPDATE
- Previous country code 00, new country code DE
- Continue interface setup after channel list update
- ctrl_iface not configured!
- random: Got 20/20 bytes from /dev/random
- RTM_NEWLINK: ifi_index=3 ifname= operstate=0 linkmode=0 ifi_family=0 ifi_flags=0x1043 ([UP][RUNNING])
- RTM_NEWLINK: ifi_index=3 ifname= operstate=2 linkmode=0 ifi_family=0 ifi_flags=0x1003 ([UP])
- nl80211: Event message available
- nl80211: Drv Event 36 (NL80211_CMD_REG_CHANGE) received for wlx74da38e18cfb
- nl80211: Regulatory domain change
- * initiator=1
- * type=0
- * alpha2=DE
- wlx74da38e18cfb: Event CHANNEL_LIST_CHANGED (28) received
- Channel list updated - continue setup
- nl80211: Regulatory information - country=DE (DFS-ETSI)
- nl80211: 2400-2483 @ 40 MHz 20 mBm
- nl80211: 5150-5250 @ 80 MHz 20 mBm (no outdoor)
- nl80211: 5250-5350 @ 80 MHz 20 mBm (no outdoor) (DFS)
- nl80211: 5470-5725 @ 160 MHz 26 mBm (DFS)
- nl80211: 57000-66000 @ 2160 MHz 40 mBm
- nl80211: Added 802.11b mode based on 802.11g information
- Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=20 dBm
- Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=20 dBm
- Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=20 dBm
- Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=20 dBm
- Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=20 dBm
- Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=20 dBm
- Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=20 dBm
- Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=20 dBm
- Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=20 dBm
- Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=20 dBm
- Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=20 dBm
- Allowed channel: mode=1 chan=12 freq=2467 MHz max_tx_power=20 dBm
- Allowed channel: mode=1 chan=13 freq=2472 MHz max_tx_power=20 dBm
- Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=20 dBm
- Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=20 dBm
- Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=20 dBm
- Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=20 dBm
- Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=20 dBm
- Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=20 dBm
- Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=20 dBm
- Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=20 dBm
- Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=20 dBm
- Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=20 dBm
- Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=20 dBm
- Allowed channel: mode=0 chan=12 freq=2467 MHz max_tx_power=20 dBm
- Allowed channel: mode=0 chan=13 freq=2472 MHz max_tx_power=20 dBm
- hw vht capab: 0x0, conf vht capab: 0x0
- wlx74da38e18cfb: interface state COUNTRY_UPDATE->HT_SCAN
- Scan for neighboring BSSes prior to enabling 40 MHz channel
- 40 MHz affected channel range: [2397,2447] MHz
- wlx74da38e18cfb: nl80211: scan request
- nl80211: Scan frequency 2412 MHz
- nl80211: Scan frequency 2417 MHz
- nl80211: Scan frequency 2422 MHz
- nl80211: Scan frequency 2427 MHz
- nl80211: Scan frequency 2432 MHz
- nl80211: Scan frequency 2437 MHz
- nl80211: Scan frequency 2442 MHz
- nl80211: Scan frequency 2447 MHz
- Scan requested (ret=0) - scan timeout 10 seconds
- Interface initialization will be completed in a callback
- nl80211: Event message available
- nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlx74da38e18cfb
- wlx74da38e18cfb: nl80211: Scan trigger
- wlx74da38e18cfb: Event SCAN_STARTED (47) received
- Unknown event 47
- RTM_NEWLINK: ifi_index=3 ifname= wext ifi_family=0 ifi_flags=0x1003 ([UP])
- nl80211: Event message available
- nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlx74da38e18cfb
- wlx74da38e18cfb: nl80211: New scan results available
- nl80211: Scan included frequencies: 2412 2417 2422 2427 2432 2437 2442 2447
- wlx74da38e18cfb: Event SCAN_RESULTS (3) received
- nl80211: Received scan results (4 BSSes)
- 40 MHz affected channel range: [2397,2447] MHz
- Found overlapping 20 MHz HT BSS: 00:0e:8f:20:55:63 freq=2437
- Overlapping 20 MHz BSS is found
- 20/40 MHz operation not permitted on channel pri=1 sec=5 based on overlapping BSSes
- Completing interface initialization
- Mode: IEEE 802.11g Channel: 1 Frequency: 2412 MHz
- DFS 0 channels required radar detection
- nl80211: Set freq 2412 (ht_enabled=1, vht_enabled=0, bandwidth=20 MHz, cf1=2412 MHz, cf2=0 MHz)
- * freq=2412
- * vht_enabled=0
- * ht_enabled=1
- * sec_channel_offset=0
- * channel_type=1
- RATE[0] rate=10 flags=0x1
- RATE[1] rate=20 flags=0x1
- RATE[2] rate=55 flags=0x1
- RATE[3] rate=110 flags=0x1
- RATE[4] rate=60 flags=0x0
- RATE[5] rate=90 flags=0x0
- RATE[6] rate=120 flags=0x0
- RATE[7] rate=180 flags=0x0
- RATE[8] rate=240 flags=0x0
- RATE[9] rate=360 flags=0x0
- RATE[10] rate=480 flags=0x0
- RATE[11] rate=540 flags=0x0
- hostapd_setup_bss(hapd=0x5556f1467900 (wlx74da38e18cfb), first=1)
- wlx74da38e18cfb: Flushing old station entries
- nl80211: flush -> DEL_STATION wlx74da38e18cfb (all)
- wlx74da38e18cfb: Deauthenticate all stations
- nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
- nl80211: send_mlme -> send_frame
- nl80211: send_frame - Use bss->freq=2412
- nl80211: send_frame -> send_frame_cmd
- nl80211: CMD_FRAME freq=2412 wait=0 no_cck=0 no_ack=0 offchanok=0
- CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff 74 da 38 e1 8c fb 74 da 38 e1 8c fb 00 00 02 00
- nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2412 wait=0)
- wpa_driver_nl80211_set_key: ifindex=3 (wlx74da38e18cfb) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0
- wpa_driver_nl80211_set_key: ifindex=3 (wlx74da38e18cfb) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0
- wpa_driver_nl80211_set_key: ifindex=3 (wlx74da38e18cfb) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0
- wpa_driver_nl80211_set_key: ifindex=3 (wlx74da38e18cfb) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0
- Using interface wlx74da38e18cfb with hwaddr 74:da:38:e1:8c:fb and ssid "glotzklotz"
- Deriving WPA PSK based on passphrase
- SSID - hexdump_ascii(len=10):
- 67 6c 6f 74 7a 6b 6c 6f 74 7a glotzklotz
- PSK (ASCII passphrase) - hexdump_ascii(len=16): [REMOVED]
- PSK (from passphrase) - hexdump(len=32): [REMOVED]
- Get randomness: len=32 entropy=7
- GMK - hexdump(len=32): [REMOVED]
- Get randomness: len=32 entropy=0
- Key Counter - hexdump(len=32): [REMOVED]
- WPA: Delay group state machine start until Beacon frames have been configured
- RSN pre-auth interface 'wlan0'
- l2_packet_init: ioctl[SIOCGIFINDEX]: No such device
- Failed to open register layer 2 access to ETH_P_PREAUTH
- Initialization of RSN pre-authentication failed.
- wlx74da38e18cfb: Flushing old station entries
- nl80211: flush -> DEL_STATION wlx74da38e18cfb (all)
- wlx74da38e18cfb: Deauthenticate all stations
- nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
- nl80211: send_mlme -> send_frame
- nl80211: send_frame - Use bss->freq=2412
- nl80211: send_frame -> send_frame_cmd
- nl80211: CMD_FRAME freq=2412 wait=0 no_cck=0 no_ack=0 offchanok=0
- CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff 74 da 38 e1 8c fb 74 da 38 e1 8c fb 00 00 03 00
- nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2412 wait=0)
- wpa_driver_nl80211_set_key: ifindex=3 (wlx74da38e18cfb) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0
- wpa_driver_nl80211_set_key: ifindex=3 (wlx74da38e18cfb) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0
- wpa_driver_nl80211_set_key: ifindex=3 (wlx74da38e18cfb) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0
- wpa_driver_nl80211_set_key: ifindex=3 (wlx74da38e18cfb) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0
- hostapd_free_hapd_data(wlx74da38e18cfb)
- Interface initialization failed
- wlx74da38e18cfb: interface state HT_SCAN->DISABLED
- wlx74da38e18cfb: AP-DISABLED
- hostapd_interface_deinit_free(0x5556f1466710)
- hostapd_interface_deinit_free: num_bss=1 conf->num_bss=1
- hostapd_interface_deinit(0x5556f1466710)
- wlx74da38e18cfb: interface state DISABLED->DISABLED
- hostapd_bss_deinit: deinit bss wlx74da38e18cfb
- wlx74da38e18cfb: Deauthenticate all stations
- nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
- nl80211: send_mlme -> send_frame
- nl80211: send_frame - Use bss->freq=2412
- nl80211: send_frame -> send_frame_cmd
- nl80211: CMD_FRAME freq=2412 wait=0 no_cck=0 no_ack=0 offchanok=0
- CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff 74 da 38 e1 8c fb 74 da 38 e1 8c fb 00 00 03 00
- nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2412 wait=0)
- wlx74da38e18cfb: AP-DISABLED
- hostapd_cleanup(hapd=0x5556f1467900 (wlx74da38e18cfb))
- hostapd_free_hapd_data: Interface wlx74da38e18cfb wasn't started
- hostapd_interface_deinit_free: driver=0x5556efa8bd00 drv_priv=0x5556f146ae50 -> hapd_deinit
- nl80211: deinit ifname=wlx74da38e18cfb disabled_11b_rates=0
- nl80211: Remove monitor interface: refcount=0
- nl80211: Remove beacon (ifindex=3)
- netlink: Operstate: ifindex=3 linkmode=0 (kernel-control), operstate=6 (IF_OPER_UP)
- nl80211: Set mode ifindex 3 iftype 2 (STATION)
- nl80211: Teardown AP(wlx74da38e18cfb) - device_ap_sme=0 use_monitor=0
- nl80211: Unsubscribe mgmt frames handle 0x8888ddde79cef989 (AP teardown)
- hostapd_interface_free(0x5556f1466710)
- hostapd_interface_free: free hapd 0x5556f1467900
- hostapd_cleanup_iface(0x5556f1466710)
- hostapd_cleanup_iface_partial(0x5556f1466710)
- hostapd_cleanup_iface: free iface=0x5556f1466710
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement