Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- BootROM - 2.03
- Starting CP-1 IOROM 1.07
- Booting from SPI NOR flash 1 (0x32)
- Found valid image at boot postion 0x000
- lNOTICE: Starting binary extension
- NOTICE: SVC: SW Revision 0x0. SVC is not supported
- mv_ddr: mv_ddr-devel-18.09.0-g48de81a (Sep 28 2018 - 18:01:37)
- mv_ddr: completed successfully
- NOTICE: Cold boot
- NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.5(release):v1.5-210-ga388b2c (Marvell-devel-18.09.0)
- NOTICE: BL1: Built : 18:01:54, Sep 28 2018
- NOTICE: BL1: Booting BL2
- NOTICE: BL2: v1.5(release):v1.5-210-ga388b2c (Marvell-devel-18.09.0)
- NOTICE: BL2: Built : 18:02:02, Sep 28 2018
- BL2: Initiating SCP_BL2 transfer to SCP
- NOTICE: SCP_BL2 contains 5 concatenated images
- NOTICE: Skipping MSS CP3 related image
- NOTICE: Skipping MSS CP2 related image
- NOTICE: Load image to CP1 MSS AP0
- NOTICE: Loading MSS image from addr. 0x40265f4 Size 0x1ad8 to MSS at 0xf4280000
- NOTICE: Done
- NOTICE: Load image to CP0 MSS AP0
- NOTICE: Loading MSS image from addr. 0x40280cc Size 0x1ad8 to MSS at 0xf2280000
- NOTICE: Done
- NOTICE: Load image to AP0 MSS
- NOTICE: Loading MSS image from addr. 0x4029ba4 Size 0x4a40 to MSS at 0xf0580000
- NOTICE: Done
- NOTICE: BL1: Booting BL31
- lNOTICE: BL31: v1.5(release):v1.5-210-ga388b2c (Marvell-devel-18.09.0)
- NOTICE: BL31: Built : 18:02:14, Sep 28 2018
- Armada 8040 MachiatoBin Platform Init
- Comphy0-0: PCIE0 5 Gbps
- Comphy0-1: PCIE0 5 Gbps
- Comphy0-2: PCIE0 5 Gbps
- Comphy0-3: PCIE0 5 Gbps
- Comphy0-4: SFI 10.31 Gbps
- Comphy0-5: SATA1 5 Gbps
- Comphy1-0: SGMII1 1.25 Gbps
- Comphy1-1: SATA2 5 Gbps
- Comphy1-2: USB3_HOST0 5 Gbps
- Comphy1-3: SATA3 5 Gbps
- Comphy1-4: SFI 10.31 Gbps
- Comphy1-5: SGMII2 3.125 Gbps
- UTMI PHY 0 initialized to USB Host0
- UTMI PHY 1 initialized to USB Host1
- UTMI PHY 2 initialized to USB Host0
- Succesfully installed protocol interfaces
- Detected w25q32bv SPI NOR flash with page size 256 B, erase size 4 KB, total 4 MB
- ramdisk:blckio install. Status=Success
- Tianocore/EDK2 firmware version MARVELL UEFI 18.09.0
- Press ESCAPE for boot options ...
- CentOS Linux (4.14.0-49.13.1.el7a.aarch64) 7 (AltArch)
- CentOS Linux (4.14.0-49.el7a.aarch64) 7 (AltArch)
- CentOS Linux (0-rescue-611cf1f62af14dc09eeb3a3f9e36b19a) 7 (AltArch)
- Debian GNU/Linux (buster/sid) (on /dev/sdc2)
- Advanced options for Debian GNU/Linux (buster/sid) (on /dev/sdc2)
- Use the ^ and v keys to change the selection.
- Press 'e' to edit the selected item, or 'c' for a command prompt.
- The selected entry will be started automatically in 0s.
- EFI stub: Booting Linux Kernel...
- EFI stub: Using DTB from configuration table
- EFI stub: Exiting boot services and installing virtual address map...
- [ 0.000000] Booting Linux on physical CPU 0x0
- [ 0.000000] Linux version 4.14.0-49.13.1.el7a.aarch64 (mockbuild@aarch64-01.bsys.centos.org) (gcc version 4.8.5 20150623 (Red Hat 4.8.5-28) (GCC)) #1 SMP Thu Sep 27 14:45:52 UTC 2018
- [ 0.000000] Boot CPU: AArch64 Processor [410fd081]
- [ 0.000000] Machine model: Marvell 8040 MACCHIATOBin
- [ 0.000000] efi: Getting EFI parameters from FDT:
- [ 0.000000] efi: EFI v2.70 by EDK II
- [ 0.000000] efi: SMBIOS 3.0=0xbfde0000 ACPI 2.0=0xb6760000 MEMATTR=0xb764e018 RNG=0xbffdce98
- [ 0.000000] random: fast init done
- [ 0.000000] efi: seeding entropy pool
- [ 0.000000] crashkernel reserved: 0x0000000094200000 - 0x00000000b4200000 (512 MB)
- [ 0.000000] ACPI: Early table checksum verification disabled
- [ 0.000000] ACPI: RSDP 0x00000000B6760000 000024 (v02 MVEBU )
- [ 0.000000] ACPI: XSDT 0x00000000B6750000 000054 (v01 MVEBU ARMADA8K 00000000 01000013)
- [ 0.000000] ACPI: FACP 0x00000000B6730000 000114 (v06 MVEBU ARMADA8K 00000000 LNRO 00000000)
- [ 0.000000] ACPI: DSDT 0x00000000B6740000 000952 (v02 MVEBU ARMADA8K 00000003 INTL 20160108)
- [ 0.000000] ACPI: GTDT 0x00000000B6720000 00007C (v02 MVEBU ARMADA8K 00000000 LNRO 00000000)
- [ 0.000000] ACPI: APIC 0x00000000B6710000 0001E4 (v04 MVEBU ARMADA8K 00000000 LNRO 00000000)
- [ 0.000000] ACPI: MCFG 0x00000000B6700000 00003C (v01 MVEBU ARMADA8K 00000000 LNRO 00000000)
- [ 0.000000] ACPI: PPTT 0x00000000B66F0000 0001E4 (v01 MVEBU ARMADA8K 00000000 LNRO 00000000)
- [ 0.000000] ACPI: SPCR 0x00000000B66E0000 000050 (v02 MVEBU ARMADA8K 00000000 LNRO 00000000)
- [ 0.000000] ACPI: SPCR: console: uart,mmio32,0xf0512000,115200
- [ 0.000000] ACPI: NUMA: Failed to initialise from firmware
- [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000043fffffff]
- [ 0.000000] NUMA: NODE_DATA [mem 0x43fffe500-0x43fffffff]
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA [mem 0x0000000000000000-0x00000000ffffffff]
- [ 0.000000] Normal [mem 0x0000000100000000-0x000000043fffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] node 0: [mem 0x0000000005400000-0x00000000b66dffff]
- [ 0.000000] node 0: [mem 0x00000000b66e0000-0x00000000b676ffff]
- [ 0.000000] node 0: [mem 0x00000000b6770000-0x00000000bf80ffff]
- [ 0.000000] node 0: [mem 0x00000000bf810000-0x00000000bfbeffff]
- [ 0.000000] node 0: [mem 0x00000000bfbf0000-0x00000000bfc8ffff]
- [ 0.000000] node 0: [mem 0x00000000bfc90000-0x00000000bffdffff]
- [ 0.000000] node 0: [mem 0x00000000bffe0000-0x00000000bfffffff]
- [ 0.000000] node 0: [mem 0x0000000100000000-0x000000043fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000043fffffff]
- [ 0.000000] psci: probing for conduit method from ACPI.
- [ 0.000000] psci: PSCIv1.1 detected in firmware.
- [ 0.000000] psci: Using standard PSCI v0.2 function IDs
- [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
- [ 0.000000] psci: SMC Calling Convention v1.1
- [ 0.000000] percpu: Embedded 3 pages/cpu @ffff80043fea0000 s124184 r8192 d64232 u196608
- [ 0.000000] Detected PIPT I-cache on CPU0
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 261568
- [ 0.000000] Policy zone: Normal
- [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-4.14.0-49.13.1.el7a.aarch64 root=/dev/mapper/centos-root ro crashkernel=auto rd.lvm.lv=centos/root rd.lvm.lv=centos/swap console=ttyS0,115200 LANG=en_US.UTF-8
- [ 0.000000] PID hash table entries: 4096 (order: -1, 32768 bytes)
- [ 0.000000] software IO TLB [mem 0xbb810000-0xbf810000] (64MB) mapped at [ffff8000bb810000-ffff8000bf80ffff]
- [ 0.000000] Memory: 16096192K/16756736K available (8060K kernel code, 1818K rwdata, 3392K rodata, 1280K init, 7738K bss, 660544K reserved, 0K cma-reserved)
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] modules : 0xffff000000000000 - 0xffff000008000000 ( 128 MB)
- [ 0.000000] vmalloc : 0xffff000008000000 - 0xffff7bdfffff0000 (126847 GB)
- [ 0.000000] .text : 0xffff000008080000 - 0xffff000008860000 ( 8064 KB)
- [ 0.000000] .rodata : 0xffff000008860000 - 0xffff000008bc0000 ( 3456 KB)
- [ 0.000000] .init : 0xffff000008bc0000 - 0xffff000008d00000 ( 1280 KB)
- [ 0.000000] .data : 0xffff000008d00000 - 0xffff000008ec6a00 ( 1819 KB)
- [ 0.000000] .bss : 0xffff000008ec6a00 - 0xffff000009655598 ( 7739 KB)
- [ 0.000000] fixed : 0xffff7fdffe790000 - 0xffff7fdffec00000 ( 4544 KB)
- [ 0.000000] PCI I/O : 0xffff7fdffee00000 - 0xffff7fdfffe00000 ( 16 MB)
- [ 0.000000] vmemmap : 0xffff7fe000000000 - 0xffff800000000000 ( 128 GB maximum)
- [ 0.000000] 0xffff7fe000000000 - 0xffff7fe001100000 ( 17 MB actual)
- [ 0.000000] memory : 0xffff800000000000 - 0xffff800440000000 ( 17408 MB)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
- [ 0.000000] ftrace: allocating 30104 entries in 8 pages
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] RCU restricting CPUs from NR_CPUS=4096 to nr_cpu_ids=4.
- [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
- [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
- [ 0.000000] GIC: Using split EOI/Deactivate mode
- [ 0.000000] GICv2m: range[mem 0xf0280000-0xf0280fff], SPI[160:191]
- [ 0.000000] GICv2m: range[mem 0xf0290000-0xf0290fff], SPI[192:223]
- [ 0.000000] GICv2m: range[mem 0xf02a0000-0xf02a0fff], SPI[224:255]
- [ 0.000000] GICv2m: range[mem 0xf02b0000-0xf02b0fff], SPI[256:287]
- [ 0.000000] Offload RCU callbacks from CPUs: .
- [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
- [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
- [ 0.000001] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
- [ 0.000042] Console: colour dummy device 80x25
- [ 0.000083] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
- [ 0.000088] pid_max: default: 32768 minimum: 301
- [ 0.000105] ACPI: Core revision 20170728
- [ 0.000507] ACPI: 1 ACPI AML tables successfully acquired and loaded
- [ 0.000539] Security Framework initialized
- [ 0.000544] SELinux: Initializing.
- [ 0.001882] Dentry cache hash table entries: 2097152 (order: 8, 16777216 bytes)
- [ 0.002523] Inode-cache hash table entries: 1048576 (order: 7, 8388608 bytes)
- [ 0.002552] Mount-cache hash table entries: 32768 (order: 2, 262144 bytes)
- [ 0.002575] Mountpoint-cache hash table entries: 32768 (order: 2, 262144 bytes)
- [ 0.003145] ASID allocator initialised with 32768 entries
- [ 0.003176] Hierarchical SRCU implementation.
- [ 0.003670] Remapping and enabling EFI services.
- [ 0.003695] EFI remap 0x00000000bf810000 => 0000000020000000
- [ 0.003701] EFI remap 0x00000000bfc90000 => 00000000203e0000
- [ 0.003704] EFI remap 0x00000000f4284000 => 0000000020734000
- [ 0.003706] EFI remap 0x00000000f4440000 => 0000000020740000
- [ 0.003709] EFI remap 0x00000000f4700000 => 0000000020750000
- [ 0.003712] EFI remap 0x00000000f93c0000 => 0000000020760000
- [ 0.003836] smp: Bringing up secondary CPUs ...
- [ 0.004134] Detected PIPT I-cache on CPU1
- [ 0.004165] CPU1: Booted secondary processor [410fd081]
- [ 0.004494] Detected PIPT I-cache on CPU2
- [ 0.004517] CPU2: Booted secondary processor [410fd081]
- [ 0.004851] Detected PIPT I-cache on CPU3
- [ 0.004866] CPU3: Booted secondary processor [410fd081]
- [ 0.004910] smp: Brought up 1 node, 4 CPUs
- [ 0.004919] SMP: Total of 4 processors activated.
- [ 0.004922] CPU features: detected feature: 32-bit EL0 Support
- [ 0.004925] CPU features: detected feature: Kernel page table isolation (KPTI)
- [ 0.005016] CPU: All CPU(s) started at EL2
- [ 0.005027] alternatives: patching kernel code
- [ 0.005605] devtmpfs: initialized
- [ 0.005930] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.005943] futex hash table entries: 1024 (order: 1, 131072 bytes)
- [ 0.006052] pinctrl core: initialized pinctrl subsystem
- [ 0.006145] SMBIOS 3.0.0 present.
- [ 0.006153] DMI: Marvell Armada 8040 MacchiatoBin/Armada 8040 MacchiatoBin, BIOS EDK II Sep 5 2018
- [ 0.006274] NET: Registered protocol family 16
- [ 0.006552] cpuidle: using governor menu
- [ 0.006626] vdso: 2 pages (1 code @ ffff000008870000, 1 data @ ffff000008d20000)
- [ 0.006630] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
- [ 0.006758] DMA: preallocated 256 KiB pool for atomic allocations
- [ 0.006775] ACPI: bus type PCI registered
- [ 0.006779] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
- [ 0.006834] Serial: AMBA PL011 UART driver
- [ 0.008714] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
- [ 0.008718] HugeTLB registered 512 MiB page size, pre-allocated 0 pages
- [ 0.009314] ACPI: Added _OSI(Module Device)
- [ 0.009318] ACPI: Added _OSI(Processor Device)
- [ 0.009321] ACPI: Added _OSI(3.0 _SCP Extensions)
- [ 0.009324] ACPI: Added _OSI(Processor Aggregator Device)
- [ 0.010295] ACPI: Interpreter enabled
- [ 0.010299] ACPI: Using GIC for interrupt routing
- [ 0.010317] ACPI: MCFG table detected, 1 entries
- [ 0.012280] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00])
- [ 0.012289] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
- [ 0.012523] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
- [ 0.012786] acpi PNP0A08:00: ECAM area [mem 0xe0008000-0xe0107fff] reserved by PNP0C02:00
- [ 0.012794] acpi PNP0A08:00: ECAM at [mem 0xe0008000-0xe0107fff] for [bus 00]
- [ 0.012822] Remapped I/O 0x00000000eff00000 to [io 0x0000-0xffff window]
- [ 0.012960] PCI host bridge to bus 0000:00
- [ 0.012965] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xdfffffff window]
- [ 0.012968] pci_bus 0000:00: root bus resource [mem 0x800000000-0x8ffffffff window]
- [ 0.012971] pci_bus 0000:00: root bus resource [io 0x0000-0xffff window]
- [ 0.012974] pci_bus 0000:00: root bus resource [bus 00]
- [ 0.013369] pci 0000:00:00.0: BAR 1: assigned [mem 0xc0000000-0xc007ffff]
- [ 0.013377] pci 0000:00:00.0: BAR 6: assigned [mem 0xc0080000-0xc00bffff pref]
- [ 0.013381] pci 0000:00:00.0: BAR 0: assigned [mem 0xc00c0000-0xc00dffff]
- [ 0.013388] pci 0000:00:00.0: BAR 3: assigned [mem 0xc00e0000-0xc00e3fff]
- [ 0.013395] pci 0000:00:00.0: BAR 2: assigned [io 0x1000-0x101f]
- [ 0.013538] vgaarb: loaded
- [ 0.013704] SCSI subsystem initialized
- [ 0.013804] ACPI: bus type USB registered
- [ 0.013830] usbcore: registered new interface driver usbfs
- [ 0.013841] usbcore: registered new interface driver hub
- [ 0.013866] usbcore: registered new device driver usb
- [ 0.013940] EDAC MC: Ver: 3.0.0
- [ 0.014037] Registered efivars operations
- [ 0.014640] NetLabel: Initializing
- [ 0.014644] NetLabel: domain hash size = 128
- [ 0.014646] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
- [ 0.014669] NetLabel: unlabeled traffic allowed by default
- [ 0.014785] clocksource: Switched to clocksource arch_sys_counter
- [ 0.030356] VFS: Disk quotas dquot_6.6.0
- [ 0.030395] VFS: Dquot-cache hash table entries: 8192 (order 0, 65536 bytes)
- [ 0.030542] pnp: PnP ACPI init
- [ 0.030678] system 00:00: [mem 0xe0008000-0xf0007fff] could not be reserved
- [ 0.030696] pnp: PnP ACPI: found 1 devices
- [ 0.032861] NET: Registered protocol family 2
- [ 0.033074] TCP established hash table entries: 131072 (order: 4, 1048576 bytes)
- [ 0.033480] TCP bind hash table entries: 65536 (order: 4, 1048576 bytes)
- [ 0.033911] TCP: Hash tables configured (established 131072 bind 65536)
- [ 0.033966] UDP hash table entries: 8192 (order: 2, 262144 bytes)
- [ 0.034128] UDP-Lite hash table entries: 8192 (order: 2, 262144 bytes)
- [ 0.034365] NET: Registered protocol family 1
- [ 0.034474] Unpacking initramfs...
- [ 0.421895] Freeing initrd memory: 19520K
- [ 0.422086] hw perfevents: enabled with armv8_pmuv3_0 PMU driver, 7 counters available
- [ 0.422103] kvm [1]: 8-bit VMID
- [ 0.422105] kvm [1]: IDMAP page: 82c000
- [ 0.422108] kvm [1]: HYP VA range: 800000000000:ffffffffffff
- [ 0.422229] kvm [1]: GICV region size/alignment is unsafe, using trapping (reduced performance)
- [ 0.422238] kvm [1]: vgic-v2@f0240000
- [ 0.422283] kvm [1]: vgic interrupt IRQ1
- [ 0.422290] kvm [1]: virtual timer IRQ3
- [ 0.422335] kvm [1]: Hyp mode initialized successfully
- [ 0.449299] audit: initializing netlink subsys (disabled)
- [ 0.449379] audit: type=2000 audit(0.440:1): state=initialized audit_enabled=0 res=1
- [ 0.449521] Initialise system trusted keyrings
- [ 0.449574] workingset: timestamp_bits=44 max_order=18 bucket_order=0
- [ 0.451247] zbud: loaded
- [ 0.506461] NET: Registered protocol family 38
- [ 0.506468] Key type asymmetric registered
- [ 0.506471] Asymmetric key parser 'x509' registered
- [ 0.506543] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
- [ 0.506590] io scheduler noop registered
- [ 0.506594] io scheduler deadline registered (default)
- [ 0.506658] io scheduler cfq registered
- [ 0.506660] io scheduler mq-deadline registered
- [ 0.506662] io scheduler kyber registered
- [ 0.506755] atomic64_test: passed
- [ 0.507281] ACPI GTDT: found 1 SBSA generic Watchdog(s).
- [ 0.507426] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
- [ 0.507814] console [ttyS0] disabled
- [ 0.527943] HISI0031:00: ttyS0 at MMIO 0xf0512000 (irq = 10, base_baud = 12500000) is a 16550A
- [ 1.752739] console [ttyS0] enabled
- [ 1.756707] rdac: device handler registered
- [ 1.760965] hp_sw: device handler registered
- [ 1.765262] emc: device handler registered
- [ 1.769416] alua: device handler registered
- [ 1.773776] libphy: Fixed MDIO Bus: probed
- [ 1.777956] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 1.784511] ehci-pci: EHCI PCI platform driver
- [ 1.788995] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 1.795220] ohci-pci: OHCI PCI platform driver
- [ 1.799690] uhci_hcd: USB Universal Host Controller Interface driver
- [ 1.806166] xhci-hcd PNP0D10:00: xHCI Host Controller
- [ 1.811291] xhci-hcd PNP0D10:00: new USB bus registered, assigned bus number 1
- [ 1.818638] xhci-hcd PNP0D10:00: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
- [ 1.826958] xhci-hcd PNP0D10:00: irq 7, io mem 0xf2500000
- [ 1.832432] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- [ 1.839254] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 1.846510] usb usb1: Product: xHCI Host Controller
- [ 1.851406] usb usb1: Manufacturer: Linux 4.14.0-49.13.1.el7a.aarch64 xhci-hcd
- [ 1.858660] usb usb1: SerialNumber: PNP0D10:00
- [ 1.863261] hub 1-0:1.0: USB hub found
- [ 1.867040] hub 1-0:1.0: 1 port detected
- [ 1.871064] xhci-hcd PNP0D10:00: xHCI Host Controller
- [ 1.876186] xhci-hcd PNP0D10:00: new USB bus registered, assigned bus number 2
- [ 1.883457] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
- [ 1.891616] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
- [ 1.898435] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 1.905689] usb usb2: Product: xHCI Host Controller
- [ 1.910585] usb usb2: Manufacturer: Linux 4.14.0-49.13.1.el7a.aarch64 xhci-hcd
- [ 1.917839] usb usb2: SerialNumber: PNP0D10:00
- [ 1.922431] hub 2-0:1.0: USB hub found
- [ 1.926209] hub 2-0:1.0: 1 port detected
- [ 1.930255] xhci-hcd PNP0D10:01: xHCI Host Controller
- [ 1.935386] xhci-hcd PNP0D10:01: new USB bus registered, assigned bus number 3
- [ 1.942719] xhci-hcd PNP0D10:01: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
- [ 1.951029] xhci-hcd PNP0D10:01: irq 8, io mem 0xf2510000
- [ 1.956497] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
- [ 1.963311] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 1.970569] usb usb3: Product: xHCI Host Controller
- [ 1.975473] usb usb3: Manufacturer: Linux 4.14.0-49.13.1.el7a.aarch64 xhci-hcd
- [ 1.982723] usb usb3: SerialNumber: PNP0D10:01
- [ 1.987340] hub 3-0:1.0: USB hub found
- [ 1.991111] hub 3-0:1.0: 1 port detected
- [ 1.995143] xhci-hcd PNP0D10:01: xHCI Host Controller
- [ 2.000259] xhci-hcd PNP0D10:01: new USB bus registered, assigned bus number 4
- [ 2.007536] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
- [ 2.015693] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
- [ 2.022508] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 2.029763] usb usb4: Product: xHCI Host Controller
- [ 2.034659] usb usb4: Manufacturer: Linux 4.14.0-49.13.1.el7a.aarch64 xhci-hcd
- [ 2.041914] usb usb4: SerialNumber: PNP0D10:01
- [ 2.046542] hub 4-0:1.0: USB hub found
- [ 2.050314] hub 4-0:1.0: 1 port detected
- [ 2.054358] xhci-hcd PNP0D10:02: xHCI Host Controller
- [ 2.059484] xhci-hcd PNP0D10:02: new USB bus registered, assigned bus number 5
- [ 2.066826] xhci-hcd PNP0D10:02: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
- [ 2.075142] xhci-hcd PNP0D10:02: irq 9, io mem 0xf4500000
- [ 2.080607] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
- [ 2.087426] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 2.094677] usb usb5: Product: xHCI Host Controller
- [ 2.099576] usb usb5: Manufacturer: Linux 4.14.0-49.13.1.el7a.aarch64 xhci-hcd
- [ 2.106833] usb usb5: SerialNumber: PNP0D10:02
- [ 2.111431] hub 5-0:1.0: USB hub found
- [ 2.115207] hub 5-0:1.0: 1 port detected
- [ 2.119220] xhci-hcd PNP0D10:02: xHCI Host Controller
- [ 2.124334] xhci-hcd PNP0D10:02: new USB bus registered, assigned bus number 6
- [ 2.131611] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
- [ 2.139768] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
- [ 2.146587] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 2.153838] usb usb6: Product: xHCI Host Controller
- [ 2.158740] usb usb6: Manufacturer: Linux 4.14.0-49.13.1.el7a.aarch64 xhci-hcd
- [ 2.165995] usb usb6: SerialNumber: PNP0D10:02
- [ 2.170596] hub 6-0:1.0: USB hub found
- [ 2.174366] hub 6-0:1.0: 1 port detected
- [ 2.178440] usbcore: registered new interface driver usbserial
- [ 2.184303] usbcore: registered new interface driver usbserial_generic
- [ 2.190869] usbserial: USB Serial support registered for generic
- [ 2.196980] mousedev: PS/2 mouse device common for all mice
- [ 2.202709] rtc-efi rtc-efi: rtc core: registered rtc-efi as rtc0
- [ 2.209031] EFI Variables Facility v0.08 2004-May-17
- [ 2.214589] hidraw: raw HID events driver (C) Jiri Kosina
- [ 2.220130] usbcore: registered new interface driver usbhid
- [ 2.225733] usbhid: USB HID core driver
- [ 2.229695] drop_monitor: Initializing network drop monitor service
- [ 2.236069] Initializing XFRM netlink socket
- [ 2.240487] NET: Registered protocol family 10
- [ 2.245206] Segment Routing with IPv6
- [ 2.248899] NET: Registered protocol family 17
- [ 2.253600] registered taskstats version 1
- [ 2.257727] Loading compiled-in X.509 certificates
- [ 2.314250] Loaded X.509 cert 'CentOS Linux kernel signing key: c70a568496a49bd9e2518f1f432190611f5394e2'
- [ 2.323891] Loaded X.509 cert 'CentOS Linux Driver update signing key: 7f421ee0ab69461574bb358861dbe77762a4201b'
- [ 2.334132] Loaded X.509 cert 'CentOS Linux kpatch signing key: ea0413152cde1d98ebdca3fe6f0230904c9ef717'
- [ 2.343783] zswap: loaded using pool lzo/zbud
- [ 2.351212] Key type big_key registered
- [ 2.355165] rtc-efi rtc-efi: setting system clock to 2018-10-04 15:53:08 UTC (1538668388)
- [ 2.365319] usb 3-1: new high-speed USB device number 2 using xhci-hcd
- [ 2.373034] Freeing unused kernel memory: 1280K
- [ 2.386958] systemd[1]: systemd 219 running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 -SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
- [ 2.405333] systemd[1]: Detected architecture arm64.
- [ 2.410320] systemd[1]: Running in initial RAM disk.
- Welcome to CentOS Linux 7 (AltArch) dracut-033-535.el7_5.1 (Initramfs)!
- [ 2.444874] systemd[1]: Set hostname to <localhost.localdomain>.
- [ OK ] Reached target Swap.
- [ 2.534826] systemd[1]: Reached target Swap.
- [ 2.539130] systemd[1]: Starting Swap.
- [ OK ] Created slice Root Slice.
- [ 2.555348] usb 3-1: New USB device found, idVendor=125f, idProduct=db8a
- [ 2.562079] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
- [ 2.569252] usb 3-1: Product: ADATA USB Flash Drive
- [ 2.574148] usb 3-1: Manufacturer: ADATA
- [ 2.578089] usb 3-1: SerialNumber: 2661510440170255
- [ 2.584824] systemd[1]: Created slice Root Slice.
- [ 2.589561] systemd[1]: Starting Root Slice.
- [ OK ] Listening on udev Control Socket.
- [ 2.624812] systemd[1]: Listening on udev Control Socket.
- [ 2.630246] systemd[1]: Starting udev Control Socket.
- [ OK ] Listening on Journal Socket.
- [ OK ] Listening on udev Kernel Socket.
- [ OK ] Reached target Sockets.
- [ OK ] Reached target Timers.
- [ OK ] Created slice System Slice.
- Starting Journal Service...
- Starting Create list of required st... nodes for the current kernel...
- Starting Setup Virtual Console...
- Starting Apply Kernel Variables...
- Starting dracut cmdline hook...
- [ OK ] Reached target Slices.
- [ OK ] Reached target Local File Systems.
- [ OK ] Started Journal Service.
- [ OK ] Started Create list of required sta...ce nodes for the current kernel.
- [ OK ] Started Setup Virtual Console.
- [ OK ] Started Apply Kernel Variables.
- [ OK ] Started dracut cmdline hook.
- Starting dracut pre-udev hook...
- [ 3.170754] device-mapper: uevent: version 1.0.3
- [ 3.175548] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-devel@redhat.com
- Starting Create Static Device Nodes in /dev...
- [ OK ] Started Create Static Device Nodes in /dev.
- [ OK ] Started dracut pre-udev hook.
- Starting udev Kernel Device Manager...
- [ OK ] Started udev Kernel Device Manager.
- Starting udev Coldplug all Devices...
- Mounting Configuration File System...
- [ 3.388048] ahci LNRO001E:00: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
- [ 3.392313] pps_core: LinuxPPS API ver. 1 registered
- [ 3.392314] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- [ 3.393899] PTP clock support registered
- [ 3.401111] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
- [ 3.401112] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
- [ 3.401210] e1000e 0000:00:00.0: enabling device (0000 -> 0002)
- [ 3.401306] e1000e 0000:00:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
- [ 3.408183] usb-storage 3-1:1.0: USB Mass Storage device detected
- [ 3.408800] scsi host0: usb-storage 3-1:1.0
- [ 3.408916] usbcore: registered new interface driver usb-storage
- [ 3.410538] usbcore: registered new interface driver uas
- [ 3.463344] ahci LNRO001E:00: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
- [ 3.463857] scsi host1: ahci
- [ 3.463987] scsi host2: ahci
- [ 3.464054] ata1: SATA max UDMA/133 mmio [mem 0xf2540000-0xf2541fff] port 0x100 irq 5
- [ 3.464056] ata2: SATA max UDMA/133 mmio [mem 0xf2540000-0xf2541fff] port 0x180 irq 5
- [ 3.464188] ahci LNRO001E:01: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
- [ 3.464192] ahci LNRO001E:01: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
- [ 3.471456] scsi host3: ahci
- [ 3.471631] scsi host4: ahci
- [ 3.471687] ata3: SATA max UDMA/133 mmio [mem 0xf4540000-0xf4541fff] port 0x100 irq 6
- [ 3.471690] ata4: SATA max UDMA/133 mmio [mem 0xf4540000-0xf4541fff] port 0x180 irq 6
- [ 3.475269] e1000e 0000:00:00.0 0000:00:00.0 (uninitialized): registered PHC clock
- [ 3.475958] mvpp2 MRVL0110:00 eth0: Using random mac address c6:d6:7d:05:35:99
- [ 3.480850] mvpp2 MRVL0110:01 eth1: Using random mac address fa:fc:70:cc:61:c2
- [ 3.485208] mvpp2 MRVL0110:01 eth2: Using random mac address 8e:a9:43:02:09:f6
- [ 3.550782] e1000e 0000:00:00.0 eth3: (PCI Express:2.5GT/s:Width x1) 68:05:ca:26:60:d9
- [ 3.550785] e1000e 0000:00:00.0 eth3: Intel(R) PRO/1000 Network Connection
- [ 3.550798] e1000e 0000:00:00.0 eth3: MAC: 3, PHY: 8, PBA No: E46981-008
- [ 3.552390] e1000e 0000:00:00.0 enp0s0: renamed from eth3
- [ OK ] Mounted Configuration File System.
- [ OK ] Started udev Coldplug all Devices.
- Starting Show Plymouth Boot Screen...
- Starting dracut initqueue hook...
- [ OK ] Reached target System Initialization.
- [ OK ] Started Show Plymouth Boot Screen.
- [ OK ] Reached target Paths.
- [ OK ] Reached target Basic System.
- [ 3.786076] ata1: SATA link down (SStatus 0 SControl 300)
- [ 3.954798] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
- [ 3.961965] ata2.00: ATA-8: WDC WD3200BEKX-75B7WT0, 01.01A01, max UDMA/133
- [ 3.968878] ata2.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
- [ 3.976633] ata2.00: configured for UDMA/133
- [ 3.981075] scsi 2:0:0:0: Direct-Access ATA WDC WD3200BEKX-7 1A01 PQ: 0 ANSI: 5
- [ 3.984802] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
- [ 3.984816] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
- [ 3.986349] ata3.00: ATA-8: WDC WD5000AAKX-00ERMA0, 15.01H15, max UDMA/133
- [ 3.986352] ata3.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
- [ 3.987158] ata4.00: ATA-8: WDC WD5000AAKX-00ERMA0, 15.01H15, max UDMA/133
- [ 3.987160] ata4.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
- [ 3.987838] ata3.00: configured for UDMA/133
- [ 3.988659] ata4.00: configured for UDMA/133
- [ 4.037831] sd 2:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
- [ 4.038361] scsi 3:0:0:0: Direct-Access ATA WDC WD5000AAKX-0 1H15 PQ: 0 ANSI: 5
- [ 4.038754] sd 3:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/466 GiB)
- [ 4.038774] sd 3:0:0:0: [sdb] Write Protect is off
- [ 4.038805] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- [ 4.039441] scsi 4:0:0:0: Direct-Access ATA WDC WD5000AAKX-0 1H15 PQ: 0 ANSI: 5
- [ 4.040519] sd 4:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/466 GiB)
- [ 4.040538] sd 4:0:0:0: [sdc] Write Protect is off
- [ 4.040572] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- [ 4.082721] sdb: sdb1 sdb2 sdb3
- [ 4.083180] sd 3:0:0:0: [sdb] Attached SCSI removable disk
- [ 4.099062] sdc: sdc1 sdc2 sdc3 sdc4 sdc5 sdc6
- [ 4.099661] sd 4:0:0:0: [sdc] Attached SCSI removable disk
- [ 4.123281] sd 2:0:0:0: [sda] Write Protect is off
- [ 4.128186] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- [ 4.434177] sd 2:0:0:0: [sda] Attached SCSI removable disk
- [ 4.475050] scsi 0:0:0:0: Direct-Access ADATA USB Flash Drive 1.00 PQ: 0 ANSI: 6
- [ 4.484314] sd 0:0:0:0: [sdd] 15155200 512-byte logical blocks: (7.76 GB/7.23 GiB)
- [ 4.492097] sd 0:0:0:0: [sdd] Write Protect is off
- [ 4.497036] sd 0:0:0:0: [sdd] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA
- [ 4.509235] sdd: sdd1 sdd2
- [ 4.512807] sd 0:0:0:0: [sdd] Attached SCSI removable disk
- [ OK ] Found device /dev/mapper/centos-root.
- Starting File System Check on /dev/mapper/centos-root...
- [ OK ] Started File System Check on /dev/mapper/centos-root.
- [ OK ] Started dracut initqueue hook.
- Mounting /sysroot...
- [ OK ] Reached target Remote File Systems (Pre).
- [ OK ] Reached target Remote File Systems.
- [ 5.345274] SGI XFS with ACLs, security attributes, no debug enabled
- [ 5.353511] XFS (dm-0): Mounting V5 Filesystem
- [ 5.636411] XFS (dm-0): Ending clean mount
- [ OK ] Mounted /sysroot.
- [ OK ] Reached target Initrd Root File System.
- Starting Reload Configuration from the Real Root...
- [ OK ] Started Reload Configuration from the Real Root.
- [ OK ] Reached target Initrd File Systems.
- [ OK ] Reached target Initrd Default Target.
- Starting dracut pre-pivot and cleanup hook...
- [ OK ] Started dracut pre-pivot and cleanup hook.
- Starting Cleaning Up and Shutting Down Daemons...
- Starting Plymouth switch root service...
- [ OK ] Stopped target Timers.
- [ OK ] Stopped Cleaning Up and Shutting Down Daemons.
- [ OK ] Stopped dracut pre-pivot and cleanup hook.
- Stopping dracut pre-pivot and cleanup hook...
- [ OK ] Stopped target Initrd Default Target.
- [ OK ] Stopped target Remote File Systems.
- [ OK ] Stopped target Remote File Systems (Pre).
- [ OK ] Stopped dracut initqueue hook.
- Stopping dracut initqueue hook...
- [ OK ] Stopped target Basic System.
- [ OK ] Stopped target Paths.
- [ OK ] Stopped target Slices.
- [ OK ] Stopped target System Initialization.
- [ OK ] Stopped Apply Kernel Variables.
- Stopping Apply Kernel Variables...
- [ OK ] Stopped target Local File Systems.
- [ OK ] Stopped target Swap.
- [ OK ] Stopped udev Coldplug all Devices.
- Stopping udev Coldplug all Devices...
- Stopping udev Kernel Device Manager...
- [ OK ] Stopped target Sockets.
- [ OK ] Started Plymouth switch root service.
- [ OK ] Stopped udev Kernel Device Manager.
- [ OK ] Stopped dracut pre-udev hook.
- Stopping dracut pre-udev hook...
- [ OK ] Stopped dracut cmdline hook.
- Stopping dracut cmdline hook...
- [ OK ] Stopped Create Static Device Nodes in /dev.
- Stopping Create Static Device Nodes in /dev...
- [ OK ] Stopped Create list of required sta...ce nodes for the current kernel.
- Stopping Create list of required st... nodes for the current kernel...
- [ OK ] Closed udev Kernel Socket.
- [ OK ] Closed udev Control Socket.
- Starting Cleanup udevd DB...
- [ OK ] Started Cleanup udevd DB.
- [ OK ] Reached target Switch Root.
- Starting Switch Root...
- [ 6.281080] systemd-journald[193]: Received SIGTERM from PID 1 (systemd).
- [ 6.380959] systemd: 20 output lines suppressed due to ratelimiting
- [ 6.675213] audit: type=1404 audit(1538668392.810:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
- [ 6.956815] SELinux: Permission getrlimit in class process not defined in policy.
- [ 6.964437] SELinux: Permission map in class file not defined in policy.
- [ 6.971265] SELinux: Permission map in class dir not defined in policy.
- [ 6.978001] SELinux: Permission map in class lnk_file not defined in policy.
- [ 6.985168] SELinux: Permission map in class chr_file not defined in policy.
- [ 6.992333] SELinux: Permission map in class blk_file not defined in policy.
- [ 6.999502] SELinux: Permission map in class sock_file not defined in policy.
- [ 7.006758] SELinux: Permission map in class fifo_file not defined in policy.
- [ 7.014014] SELinux: Permission map in class socket not defined in policy.
- [ 7.021009] SELinux: Permission map in class tcp_socket not defined in policy.
- [ 7.028353] SELinux: Permission map in class udp_socket not defined in policy.
- [ 7.035708] SELinux: Permission map in class rawip_socket not defined in policy.
- [ 7.043224] SELinux: Permission map in class netlink_socket not defined in policy.
- [ 7.050919] SELinux: Permission map in class packet_socket not defined in policy.
- [ 7.058523] SELinux: Permission map in class key_socket not defined in policy.
- [ 7.065867] SELinux: Permission map in class unix_stream_socket not defined in policy.
- [ 7.073905] SELinux: Permission map in class unix_dgram_socket not defined in policy.
- [ 7.081866] SELinux: Permission map in class netlink_route_socket not defined in policy.
- [ 7.090081] SELinux: Permission map in class netlink_tcpdiag_socket not defined in policy.
- [ 7.098471] SELinux: Permission map in class netlink_nflog_socket not defined in policy.
- [ 7.106685] SELinux: Permission map in class netlink_xfrm_socket not defined in policy.
- [ 7.114812] SELinux: Permission map in class netlink_selinux_socket not defined in policy.
- [ 7.123197] SELinux: Permission map in class netlink_iscsi_socket not defined in policy.
- [ 7.131412] SELinux: Permission map in class netlink_audit_socket not defined in policy.
- [ 7.139628] SELinux: Permission map in class netlink_fib_lookup_socket not defined in policy.
- [ 7.148280] SELinux: Permission map in class netlink_connector_socket not defined in policy.
- [ 7.156844] SELinux: Permission map in class netlink_netfilter_socket not defined in policy.
- [ 7.165410] SELinux: Permission map in class netlink_dnrt_socket not defined in policy.
- [ 7.173534] SELinux: Permission map in class netlink_kobject_uevent_socket not defined in policy.
- [ 7.182533] SELinux: Permission map in class netlink_generic_socket not defined in policy.
- [ 7.190922] SELinux: Permission map in class netlink_scsitransport_socket not defined in policy.
- [ 7.199836] SELinux: Permission map in class netlink_rdma_socket not defined in policy.
- [ 7.207964] SELinux: Permission map in class netlink_crypto_socket not defined in policy.
- [ 7.216266] SELinux: Permission map in class appletalk_socket not defined in policy.
- [ 7.224132] SELinux: Permission map in class dccp_socket not defined in policy.
- [ 7.231566] SELinux: Permission map in class tun_socket not defined in policy.
- [ 7.238914] SELinux: Class sctp_socket not defined in policy.
- [ 7.244768] SELinux: Class icmp_socket not defined in policy.
- [ 7.250627] SELinux: Class ax25_socket not defined in policy.
- [ 7.256485] SELinux: Class ipx_socket not defined in policy.
- [ 7.262253] SELinux: Class netrom_socket not defined in policy.
- [ 7.268286] SELinux: Class atmpvc_socket not defined in policy.
- [ 7.274315] SELinux: Class x25_socket not defined in policy.
- [ 7.280086] SELinux: Class rose_socket not defined in policy.
- [ 7.285944] SELinux: Class decnet_socket not defined in policy.
- [ 7.291972] SELinux: Class atmsvc_socket not defined in policy.
- [ 7.298006] SELinux: Class rds_socket not defined in policy.
- [ 7.303773] SELinux: Class irda_socket not defined in policy.
- [ 7.309632] SELinux: Class pppox_socket not defined in policy.
- [ 7.315578] SELinux: Class llc_socket not defined in policy.
- [ 7.321345] SELinux: Class can_socket not defined in policy.
- [ 7.327116] SELinux: Class tipc_socket not defined in policy.
- [ 7.332971] SELinux: Class bluetooth_socket not defined in policy.
- [ 7.339265] SELinux: Class iucv_socket not defined in policy.
- [ 7.345123] SELinux: Class rxrpc_socket not defined in policy.
- [ 7.351065] SELinux: Class isdn_socket not defined in policy.
- [ 7.356924] SELinux: Class phonet_socket not defined in policy.
- [ 7.362953] SELinux: Class ieee802154_socket not defined in policy.
- [ 7.369335] SELinux: Class caif_socket not defined in policy.
- [ 7.375194] SELinux: Class alg_socket not defined in policy.
- [ 7.380962] SELinux: Class nfc_socket not defined in policy.
- [ 7.386732] SELinux: Class vsock_socket not defined in policy.
- [ 7.392674] SELinux: Class kcm_socket not defined in policy.
- [ 7.398445] SELinux: Class qipcrtr_socket not defined in policy.
- [ 7.404561] SELinux: Class smc_socket not defined in policy.
- [ 7.410334] SELinux: the above unknown classes and permissions will be allowed
- [ 7.417601] SELinux: policy capability network_peer_controls=1
- [ 7.423543] SELinux: policy capability open_perms=1
- [ 7.428531] SELinux: policy capability extended_socket_class=0
- [ 7.434473] SELinux: policy capability always_check_network=0
- [ 7.440331] SELinux: policy capability cgroup_seclabel=1
- [ 7.445753] SELinux: policy capability nnp_nosuid_transition=1
- [ 7.507814] audit: type=1403 audit(1538668393.640:3): policy loaded auid=4294967295 ses=4294967295
- [ 7.516650] systemd[1]: Successfully loaded SELinux policy in 849.028ms.
- [ 7.797400] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 7.802762] systemd[1]: Inserted module 'ip_tables'
- [ 7.855602] systemd[1]: Relabelled /dev and /run in 44.680ms.
- Welcome to CentOS Linux 7 (AltArch)!
- [ 9.065830] random: crng init done
- [ OK ] Stopped Switch Root.
- [ OK ] Stopped Journal Service.
- Starting Journal Service...
- [ OK ] Listening on udev Control Socket.
- Starting Read and set NIS domainname from /etc/sysconfig/network...
- [ OK ] Listening on LVM2 metadata daemon socket.
- Mounting POSIX Message Queue File System...
- [ OK ] Created slice system-getty.slice.
- Mounting Huge Pages File System...
- Mounting Debug File System...
- [ OK ] Listening on udev Kernel Socket.
- [ OK ] Set up automount Arbitrary Executab...ats File System Automount Point.
- [ OK ] Listening on Delayed Shutdown Socket.
- [ OK ] Created slice system-selinux\x2dpol...grate\x2dlocal\x2dchanges.slice.
- Starting Create list of required st... nodes for the current kernel...
- [ OK ] Listening on /dev/initctl Compatibility Named Pipe.
- [ OK ] Created slice User and Session Slice.
- [ OK ] Stopped target Switch Root.
- [ OK ] Reached target Remote File Systems.
- [ OK ] Reached target Local Encrypted Volumes.
- [ OK ] Stopped target Initrd Root File System.
- [ OK ] Stopped target Initrd File Systems.
- [ OK ] Stopped File System Check on Root Device.
- Stopping File System Check on Root Device...
- Starting Collect Read-Ahead Data...
- [ OK ] Reached target Paths.
- [ OK ] Created slice system-serial\x2dgetty.slice.
- [ OK ] Reached target Slices.
- [ OK ] Listening on LVM2 poll daemon socket.
- Starting Replay Read-Ahead Data...
- [ OK ] Listening on Device-mapper event daemon FIFOs.
- Starting Monitoring of LVM2 mirrors... dmeventd or progress polling...
- [ OK ] Started Collect Read-Ahead Data.
- [ OK ] Started Replay Read-Ahead Data.
- Starting Remount Root and Kernel File Systems...
- Starting Apply Kernel Variables...
- [ OK ] Started Journal Service.
- [ OK ] Started Create list of required sta...ce nodes for the current kernel.
- Starting Create Static Device Nodes in /dev...
- [ OK ] Started Apply Kernel Variables.
- [ OK ] Mounted Debug File System.
- [ OK ] Mounted POSIX Message Queue File System.
- [ OK ] Mounted Huge Pages File System.
- [ OK ] Started Read and set NIS domainname from /etc/sysconfig/network.
- [ OK ] Started Remount Root and Kernel File Systems.
- Starting Flush Journal to Persistent Storage...
- Starting Configure read-only root support...
- Starting Load/Save Random Seed...
- Starting udev Coldplug all Devices...
- [ OK ] Started Load/Save Random Seed.
- [ OK ] Started Create Static Device Nodes in /dev.
- Starting udev Kernel Device Manager...
- [ 9.795846] systemd-journald[592]: Received request to flush runtime journal from PID 1
- [ OK ] Started udev Coldplug all Devices.
- [ OK ] Started Flush Journal to Persistent Storage.
- [ OK ] Started Configure read-only root support.
- [ OK ] Started LVM2 metadata daemon.
- Starting LVM2 metadata daemon...
- [ OK ] Started udev Kernel Device Manager.
- [ OK ] Found device /dev/ttyS0.
- [ 11.339441] omap_rng PRP0001:00: Random Number Generator ver. 00
- [ 11.345590] omap_rng PRP0001:01: Random Number Generator ver. 00
- [ 11.354990] sbsa-gwdt sbsa-gwdt.0: Initialized with 10s timeout @ 25000000 Hz, action=0.
- [ 11.392642] sd 2:0:0:0: Attached scsi generic sg0 type 0
- [ 11.398187] sd 3:0:0:0: Attached scsi generic sg1 type 0
- [ 11.403680] sd 4:0:0:0: Attached scsi generic sg2 type 0
- [ 11.409408] sd 0:0:0:0: Attached scsi generic sg3 type 0
- [ OK ] Found device /dev/mapper/centos-swap.
- Activating swap /dev/mapper/centos-swap...
- [ 13.574346] Adding 8323008k swap on /dev/mapper/centos-swap. Priority:-2 extents:1 across:8323008k FS
- [ OK ] Activated swap /dev/mapper/centos-swap.
- [ OK ] Reached target Swap.
- [ OK ] Created slice system-lvm2\x2dpvscan.slice.
- Starting LVM2 PV scan on device 8:19...
- [ OK ] Found device WDC_WD5000AAKX-00ERMA0 2.
- [ OK ] Found device WDC_WD5000AAKX-00ERMA0 EFI\x20System\x20Partition.
- [ OK ] Started Monitoring of LVM2 mirrors,...ng dmeventd or progress polling.
- [ OK ] Reached target Loca[ 14.460194] XFS (sdb2): Mounting V5 Filesystem
- l File Systems (Pre).
- Mounting /boot...
- [ OK ] Found device /dev/mapper/centos-home.
- [ OK ] Started LVM2 PV scan on device 8:19.
- Mounting /home...
- [ 16.847069] XFS (dm-2): Mounting V5 Filesystem
- [ 18.850533] XFS (sdb2): Ending clean mount
- [ OK ] Mounted /boot.
- Mounting /boot/efi...
- [ 19.007435] XFS (dm-2): Ending clean mount
- [ OK ] Mounted /home.
- [ OK ] Mounted /boot/efi.
- [ OK ] Reached target Local File Systems.
- Starting Import network configuration from initramfs...
- Starting Tell Plymouth To Write Out Runtime Data...
- [ OK ] Started Tell Plymouth To Write Out Runtime Data.
- [ OK ] Started Import network configuration from initramfs.
- Starting Create Volatile Files and Directories...
- [ OK ] Started Create Volatile Files and Directories.
- Starting Security Auditing Service...
- [ OK ] Started Security Auditing Service.
- Starting Update UTMP about System Boot/Shutdown...
- [ OK ] Started Update UTMP about System Boot/Shutdown.
- [ OK ] Reached target System Initialization.
- [ OK ] Reached target Timers.
- [ OK ] Listening on D-Bus System Message Bus Socket.
- [ OK ] Reached target Sockets.
- [ OK ] Reached target Basic System.
- [ OK ] Started D-Bus System Message Bus.
- Starting D-Bus System Message Bus...
- Starting Dump dmesg to /var/log/dmesg...
- Starting Permit User Sessions...
- [ OK ] Started irqbalance daemon.
- Starting irqbalance daemon...
- Starting NTP client/server...
- Starting Login Service...
- Starting Authorization Manager...
- [ OK ] Started Dump dmesg to /var/log/dmesg.
- [ OK ] Started Permit User Sessions.
- Starting Terminate Plymouth Boot Screen...
- [ OK ] Started Command Scheduler.
- Starting Command Scheduler...
- Starting Wait for Plymouth Boot Screen to Quit...
- [ 21.024973] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 21.570630] Ebtables v2.0 registered
- [ 21.611869] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- [ 21.627732] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
- [ 21.636023] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
- [ 21.649517] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
- [ 21.656577] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
- [ 21.662442] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
- [ 21.674167] IPv6: ADDRCONF(NETDEV_UP): enp0s0: link is not ready
- [ 21.772642] IPv6: ADDRCONF(NETDEV_UP): enp0s0: link is not ready
- [ 22.337335] nf_conntrack version 0.5.0 (65536 buckets, 262144 max)
- [ 23.185658] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
- [ 23.499127] Netfilter messages via NETLINK v0.30.
- [ 23.507574] ip_set: protocol 6
- CentOS Linux 7 (AltArch)
- Kernel 4.14.0-49.13.1.el7a.aarch64 on an aarch64
- localhost login: [ 25.995443] e1000e: enp0s0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
- [ 26.003538] IPv6: ADDRCONF(NETDEV_CHANGE): enp0s0: link becomes ready
- CentOS Linux 7 (AltArch)
- Kernel 4.14.0-49.13.1.el7a.aarch64 on an aarch64
- localhost login:
- CentOS Linux 7 (AltArch)
- Kernel 4.14.0-49.13.1.el7a.aarch64 on an aarch64
- localhost login: root
- Password:
- Last login: Thu Oct 4 13:02:30 on ttyS0
- [root@localhost ~]# ip link
- 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
- link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
- 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 2048
- link/ether c6:d6:7d:05:35:99 brd ff:ff:ff:ff:ff:ff
- 3: eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 2048
- link/ether fa:fc:70:cc:61:c2 brd ff:ff:ff:ff:ff:ff
- 4: eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 2048
- link/ether 8e:a9:43:02:09:f6 brd ff:ff:ff:ff:ff:ff
- 5: enp0s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
- link/ether 68:05:ca:26:60:d9 brd ff:ff:ff:ff:ff:ff
- [root@localhost ~]# ip addr add 10.2.80.33/16 dev eth2
- [root@localhost ~]# ping 10.2.4.2
- PING 10.2.4.2 (10.2.4.2) 56(84) bytes of data.
- 64 bytes from 10.2.4.2: icmp_seq=1 ttl=64 time=0.559 ms
- 64 bytes from 10.2.4.2: icmp_seq=2 ttl=64 time=0.267 ms
- 64 bytes from 10.2.4.2: icmp_seq=3 ttl=64 time=0.254 ms
- 64 bytes from 10.2.4.2: icmp_seq=4 ttl=64 time=0.267 ms
- --- 10.2.4.2 ping statistics ---
- 4 packets transmitted, 4 received, 0% packet loss, time 3114ms
- rtt min/avg/max/mdev = 0.254/0.336/0.559/0.130 ms
- [root@localhost ~]# ip addr add 192.168.3.2/24 dev eth0
- [root@localhost ~]# ping 192.168.3.1
- PING 192.168.3.1 (192.168.3.1) 56(84) bytes of data.
- 64 bytes from 192.168.3.1: icmp_seq=1 ttl=64 time=0.307 ms
- 64 bytes from 192.168.3.1: icmp_seq=2 ttl=64 time=0.141 ms
- 64 bytes from 192.168.3.1: icmp_seq=3 ttl=64 time=0.136 ms
- 64 bytes from 192.168.3.1: icmp_seq=4 ttl=64 time=0.131 ms
- --- 192.168.3.1 ping statistics ---
- 4 packets transmitted, 4 received, 0% packet loss, time 3087ms
- rtt min/avg/max/mdev = 0.131/0.178/0.307/0.075 ms
- [root@localhost ~]# cat /proc/interrupts
- CPU0 CPU1 CPU2 CPU3
- 1: 0 0 0 0 GICv2 25 Level vgic
- 2: 5063 3614 5829 6117 GICv2 30 Level arch_timer
- 3: 0 0 0 0 GICv2 27 Level kvm guest timer
- 5: 72 0 0 0 GICv2 114 Level ahci[LNRO001E:00]
- 6: 6795 0 0 0 GICv2 338 Level ahci[LNRO001E:01]
- 7: 0 0 0 0 GICv2 113 Level xhci-hcd:usb1
- 8: 1450 0 0 0 GICv2 112 Level xhci-hcd:usb3
- 9: 0 0 0 0 GICv2 337 Level xhci-hcd:usb5
- 10: 1945 0 0 0 GICv2 51 Level ttyS0
- 13: 36 0 0 0 GICv2 69 Level eth0
- 14: 0 34 0 0 GICv2 72 Level eth0
- 15: 0 0 8 0 GICv2 75 Level eth0
- 16: 0 0 0 10 GICv2 78 Level eth0
- 18: 4 0 0 0 GICv2 127 Level eth0
- 19: 0 0 0 0 GICv2 293 Level eth1
- 20: 0 0 0 0 GICv2 296 Level eth1
- 21: 0 0 0 0 GICv2 299 Level eth1
- 22: 0 0 0 0 GICv2 302 Level eth1
- 24: 2 0 0 0 GICv2 351 Level eth1
- 25: 410 0 0 0 GICv2 294 Level eth2
- 26: 0 5 0 0 GICv2 297 Level eth2
- 27: 0 0 8 0 GICv2 300 Level eth2
- 28: 0 0 0 22 GICv2 303 Level eth2
- 30: 3 0 0 0 GICv2 350 Level eth2
- 31: 0 0 0 0 GICv2 130 Edge arm-pmu
- 32: 0 0 0 0 GICv2 131 Edge arm-pmu
- 33: 0 0 0 0 GICv2 132 Edge arm-pmu
- 34: 0 0 0 0 GICv2 133 Edge arm-pmu
- 37: 33 0 0 512 MSI 0 Edge enp0s0-rx-0
- 38: 0 0 0 0 MSI 1 Edge enp0s0-tx-0
- 39: 1 0 0 0 MSI 2 Edge enp0s0
- IPI0: 7970 8622 5261 5289 Rescheduling interrupts
- IPI1: 19 15 599 568 Function call interrupts
- IPI2: 0 0 0 0 CPU stop interrupts
- IPI3: 0 0 0 0 CPU stop (for crash dump) interrupts
- IPI4: 0 0 0 0 Timer broadcast interrupts
- IPI5: 0 0 0 0 IRQ work interrupts
- IPI6: 0 0 0 0 CPU wake-up interrupts
- Err: 0
- [root@localhost ~]# cat /proc/meminfo
- MemTotal: 16116992 kB
- MemFree: 15467392 kB
- MemAvailable: 14359552 kB
- Buffers: 2944 kB
- Cached: 288320 kB
- SwapCached: 0 kB
- Active: 222976 kB
- Inactive: 214144 kB
- Active(anon): 149504 kB
- Inactive(anon): 10496 kB
- Active(file): 73472 kB
- Inactive(file): 203648 kB
- Unevictable: 0 kB
- Mlocked: 0 kB
- SwapTotal: 8323008 kB
- SwapFree: 8323008 kB
- Dirty: 256 kB
- Writeback: 0 kB
- AnonPages: 146240 kB
- Mapped: 40128 kB
- Shmem: 14144 kB
- Slab: 103360 kB
- SReclaimable: 20032 kB
- SUnreclaim: 83328 kB
- KernelStack: 9856 kB
- PageTables: 6208 kB
- NFS_Unstable: 0 kB
- Bounce: 0 kB
- WritebackTmp: 0 kB
- CommitLimit: 16381504 kB
- Committed_AS: 357248 kB
- VmallocTotal: 133009637312 kB
- VmallocUsed: 0 kB
- VmallocChunk: 0 kB
- HardwareCorrupted: 0 kB
- AnonHugePages: 0 kB
- ShmemHugePages: 0 kB
- ShmemPmdMapped: 0 kB
- HugePages_Total: 0
- HugePages_Free: 0
- HugePages_Rsvd: 0
- HugePages_Surp: 0
- Hugepagesize: 524288 kB
- [root@localhost ~]# dmesg | grep MRVL
- [ 3.475958] mvpp2 MRVL0110:00 eth0: Using random mac address c6:d6:7d:05:35:99
- [ 3.480850] mvpp2 MRVL0110:01 eth1: Using random mac address fa:fc:70:cc:61:c2
- [ 3.485208] mvpp2 MRVL0110:01 eth2: Using random mac address 8e:a9:43:02:09:f6
- [root@localhost ~]#
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement