Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- GXBB:BL1:08dafd:0a8993;FEAT:EDFD718C;POC:3;RCY:0;EMMC:0;READ:0;CHK:0;
- no sdio debug board detected
- TE: 59660
- BL2 Built : 15:22:26, Nov 13 2015.
- gxb g6dcf28d - xiaobo.gu@droid05
- Board Ver is 1
- rn5t567_power_init
- Board ID = 8
- CPU clk: 1536MHz
- DDR channel setting: DDR0 Rank0+1 same
- DDR0: 1024MB @ 912MHz(2T)-13
- DataBus test pass!
- AddrBus test pass!
- Load fip header from eMMC, src: 0x0000c000, des: 0x01400000, size: 0x000000b0
- Load bl30 from eMMC, src: 0x00010000, des: 0x01000000, size: 0x00009e70
- Sending bl30........................................OK.
- Run bl30...
- Load bl301 from eMMC, src: 0x0001c000, des: 0x01000000, size: 0x00001ce0
- Wait bl30...Done
- Sending bl301........OK.
- Run bl301...
- C, src: 0x00020000, des: 0x10100000, size: 0x00011130
- --- UART initialized after reboot ---
- [Reset cause: unknown]
- [Image: unknown, amlogic_v1.1.3043-8623ae6 2015-09-16 16:38:21 jianxin.pan@droid06]
- bl30: check_permit, count is 1
- bl30: check_permit: ok!
- chipidLoad bl33 from eMMC, src: 0x00034000, des: 0x01000000, size: 0x00075c10
- : ef be ad de d f0 ad ba ef be ad de not ES chip
- [0.209881 Inits done]
- secure task start!
- high task start!
- low task start!
- NOTICE: BL3-1: v1.0(debug):4621162
- NOTICE: BL3-1: Built : 13:57:23, Nov 10 2015
- INFO: BL3-1: Initializing runtime services
- INFO: BL3-1: Preparing for EL3 exit to normal world
- INFO: BL3-1: Next image address = 0x1000000
- INFO: BL3-1: Next image spsr = 0x3c9
- U-Boot 2015.01-gf208d9f (Apr 27 2016 - 17:07:09)
- DRAM: 1 GiB
- Relocation Offset is: 36eff000
- register usb cfg[0][1] = 0000000037f66de0
- vpu detect type: 5
- vpu clk_level = 7
- set vpu clk: 666667000Hz, readback: 666660000Hz(0x300)
- MMC: aml_priv->desc_buf = 0x0000000033eef6d0
- aml_priv->desc_buf = 0x0000000033ef1860
- SDIO Port B: 0, SDIO Port C: 1
- [mmc_init] mmc init success
- mmc read lba=0x4000, blocks=0x400
- Amlogic multi-dtb tool
- Multi dtb detected
- Multi dtb tool version: v2 .
- Support 2 dtbs.
- aml_dt soc: gxbb platform: jp variant: 6
- dtb 0 soc: gxbb plat: jp vari: 0
- dtb 1 soc: gxbb plat: jp vari: 6
- Find match dtb: 1
- start dts,buffer=0000000033ef3cf0,dt_addr=0000000033efbcf0
- parts: 10
- 00: cache 0000000010000000 2
- 01: logo 0000000000400000 1
- 02: recovery 0000000002000000 1
- 03: misc 0000000002000000 1
- 04: boot 0000000001400000 1
- 05: system 0000000040000000 1
- 06: backup 0000000020000000 4
- 07: persist 0000000000800000 4
- 08: panic 0000000000400000 4
- 09: data ffffffffffffffff 4
- get_dtb_struct: Get emmc dtb OK!
- [mmc_get_partition_table] skip cache partition.
- Partition table get from SPL is :
- name offset size flag
- ===================================================================================
- 0: bootloader 0 400000 0
- 1: reserved 400000 800000 0
- 2: cache c00000 10000000 2
- 3: env 10c00000 400000 0
- 4: logo 11000000 400000 1
- 5: recovery 11400000 2000000 1
- 6: misc 13400000 2000000 1
- 7: boot 15400000 1400000 1
- 8: system 16800000 40000000 1
- 9: backup 56800000 20000000 4
- 10: persist 76800000 800000 4
- 11: panic 77000000 400000 4
- 12: data 77400000 74c00000 4
- mmc read lba=0x2000, blocks=0x1
- mmc read lba=0x2001, blocks=0x1
- mmc_read_partition_tbl: mmc read partition OK!
- eMMC/TSD partition table have been checked OK!
- mmc env offset: 0x10c00000
- In: serial
- Out: serial
- Err: serial
- Boot command:
- Boot status:
- Boot message
- ""
- upgrade_step=2
- dtbLoadaddr = 0x0000000001000000
- amlkey_init() enter!
- [EFUSE_MSG]keynum is 4
- hpd_state=0
- [CANVAS]addr=0x3f800000 width=5760, height=2160
- [1080p60hz] is invalid for cvbs.
- set hdmitx VIC = 16
- config HPLL = 2970
- HPLL: 0xc800023d
- config HPLL done
- set_hpll_od3_clk_div[216] div = 6
- j = 8 vid_clk_div = 1
- hdmitx phy setting done
- hdmitx: set enc for VIC: 16
- enc_vpu_bridge_reset[977]
- reboot_mode=normal
- pull down bt_reset
- pull up bt_reset
- set hci reset
- set scan parameters
- 04 10 01 00
- set scan enable
- 04 10 01 00
- 04 10 01 00
- 04 10 01 00
- IR init done!
- Hit any key to stop autoboot: 0
- (Re)start USB...
- USB0: dwc_usb driver version: 2.94 6-June-2012
- USB (0) peri reg base: c0000000
- USB (0) use clock source: XTAL input, div: 1
- USB (0) base addr: 0xc9000000
- Force id mode: Host
- dwc_otg: Highspeed device found !
- scanning bus 0 for devices... 1 USB Device(s) found
- scanning usb for storage devices... 1 Storage Device(s) found
- reading aml_autoscript
- 795 bytes read in 25 ms (30.3 KiB/s)
- ## Executing script at 11000000
- ########## cmd=defenv
- setenv bootfromnand 0
- setenv upgrade_step 2
- setenv sddtb 'if fatload mmc 0 ${dtb_mem_addr} dtb.img; then else store dtb read $dtb_mem_addr; fi'
- setenv usbdtb 'if fatload usb 0 ${dtb_mem_addr} dtb.img; then else store dtb read $dtb_mem_addr; fi'
- setenv bootfromsd 'mmcinfo; if fatload mmc 0 ${loadaddr} kernel.img; then run sddtb; setenv bootargs ${bootargs} bootfromsd; bootm; fi'
- setenv bootfromusb 'usb start 0; if fatload usb 0 ${loadaddr} kernel.img; then run usbdtb; setenv bootargs ${bootargs} bootfromusb; bootm; fi'
- setenv bootcmd 'if test ${bootfromnand} = 1; then setenv bootfromnand 0; saveenv; else run bootfromsd; run bootfromusb; fi; run storeboot'
- saveenv
- run storeargs
- run bootfromsd
- run bootfromusb
- ## defenv_reserve
- Saving Environment to MMC...
- mmc env offset: 0x10c00000
- Writing to MMC(1)... done
- ** Bad device mmc 0 **
- board_usb_stop cfg: 0
- (Re)start USB...
- USB0: dwc_usb driver version: 2.94 6-June-2012
- USB (0) peri reg base: c0000000
- USB (0) use clock source: XTAL input, div: 1
- USB (0) base addr: 0xc9000000
- Force id mode: Host
- dwc_otg: Highspeed device found !
- scanning bus 0 for devices... 1 USB Device(s) found
- scanning usb for storage devices... 1 Storage Device(s) found
- reading kernel.img
- 12318720 bytes read in 13029 ms (922.9 KiB/s)
- fatload - load binary file from a dos filesystem
- Usage:
- fatload <interface> [<dev[:part]> [<addr> [<filename> [bytes [pos]]]]]
- - Load binary file 'filename' from 'dev' on 'interface'
- to address 'addr' from dos filesystem.
- 'pos' gives the file position to start loading from.
- If 'pos' is omitted, 0 is used. 'pos' requires 'bytes'.
- 'bytes' gives the size to load. If 'bytes' is 0 or omitted,
- the load stops on end of file.
- If either 'pos' or 'bytes' are not aligned to
- ARCH_DMA_MINALIGN then a misaligned buffer warning will
- be printed and performance will suffer for the load.
- store - STORE sub-system
- Usage:
- store store init flag
- store read name addr off|partition size
- read 'size' bytes starting at offset 'off'
- to/from memory address 'addr', skipping bad blocks.
- store write name addr off|partition size
- write 'size' bytes starting at offset 'off'
- to/from memory address 'addr', skipping bad blocks.
- store rom_write add off size.
- write uboot to the boot device
- store erase boot/data:
- erase the area which is uboot or data
- store erase dtb
- store erase key
- store scrub off|partition size
- scrub the area from offset and size
- store dtb iread/read/write <size>
- read/write dtb, size is optional
- store key read/write <size>
- read/write key, size is optional
- ee_gate_off ...
- ## Booting Android Image at 0x01080000 ...
- lzo kernelreloc_addr =33f73ea0
- copy done
- load dtb from 0x1000000 len(77af)......
- lzo kernelboard_usb_stop cfg: 0
- Uncompressing Kernel Image ... OK
- kernel loaded at 0x01080000, end = 0x01ddd460
- Loading Ramdisk to 3398e000, end 33eebe00 ... OK
- Loading Device Tree to 000000001fff5000, end 000000001ffff7ae ... OK
- Starting kernel ...
- uboot time: 27436251 us
- [ 0.000000@0] Initializing cgroup subsys cpuset
- [ 0.000000@0] Initializing cgroup subsys cpu
- [ 0.000000@0] Initializing cgroup subsys cpuacct
- [ 0.000000@0] Linux version 3.14.29 (cdu13a@missandei) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) ) #1 SMP Sun Mar 14 18:42:06 EDT 2021
- [ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
- [ 0.000000@0] no prop version_code
- [ 0.000000@0] Machine model: Amlogic
- [ 0.000000@0] bootconsole [earlycon0] enabled
- [ 0.000000@0] fdt Reserved memory table:
- [ 0.000000@0] linux,meson-fb: 0x000000003e000000 - 0x0000000040000000 (32 MiB)
- [ 0.000000@0] linux,di: 0x000000003b80c000 - 0x000000003e000000 (39 MiB)
- [ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000003b80c000, size 39 MiB
- [ 0.000000@0] linux,ion-dev: 0x000000003880c000 - 0x000000003b80c000 (48 MiB)
- [ 0.000000@0] linux,codec_mm_cma: 0x0000000027800000 - 0x0000000033800000 (192 MiB)
- [ 0.000000@0] cma: Reserved 192 MiB at 27800000, total cma pages:49152
- [ 0.000000@0] linux,picdec: 0x0000000035800000 - 0x0000000038800000 (48 MiB)
- [ 0.000000@0] cma: Reserved 48 MiB at 35800000, total cma pages:61440
- [ 0.000000@0] linux,codec_mm_reserved: 0x0000000023700000 - 0x0000000027800000 (65 MiB)
- [ 0.000000@0] fdt Reserved memory total: 427 MiB
- [ 0.000000@0] cma: Reserved 8 MiB at 35000000, total cma pages:63488
- [ 0.000000@0] psci: probing function IDs from device-tree
- [ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc033fb9000 s16704 r8192 d24256 u49152
- [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 243720
- [ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 logo=osd1,loaded,0x3f800000,1080p60hz hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= androidboot.btmac=00:00:00:00:00:00 androidboot.wifimac=00:00:00:00:00:00 androidboot.firstboot=1 androidboot.serialno=123456789ABCDEF ramoops.mem_address=0x20000000 ramoops.mem_size=0x100000 ramoops.record_size=0xc0000 ramoops.dump_oops=0 boardver=1 bootfromusb console=tty0 systemd.show_status=auto
- [ 0.000000@0] logo: osd1
- [ 0.000000@0] logo: loaded
- [ 0.000000@0] logo: 0x3f800000
- [ 0.000000@0] logo: 1080p60hz
- [ 0.000000@0] vout_serve: 1080p60hz
- [ 0.000000@0] vout_serve: en: 1
- [ 0.000000@0] vout_serve: set_vout_init_vmode: 1080p60hz
- [ 0.000000@0] logo: get hdmimode: 1080p60hz
- [ 0.000000@0] logo: get cvbsmode: 576cvbs
- [ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
- [ 0.000000@0] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
- [ 0.000000@0] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
- [ 0.000000@0] Memory: 537160K/996352K available (7457K kernel code, 857K rwdata, 4424K rodata, 936K init, 2900K bss, 459192K reserved)
- [ 0.000000@0] Virtual kernel memory layout:
- [ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
- [ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff8041560000 ( 21 MB)
- [ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
- [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc03e000000 ( 992 MB)
- [ 0.000000@0] .init : 0xffffffc001c1c000 - 0xffffffc001d06140 ( 937 kB)
- [ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001c1b7b4 ( 11886 kB)
- [ 0.000000@0] .data : 0xffffffc001d07000 - 0xffffffc001ddd460 ( 858 kB)
- [ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01c1afff]
- [ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=4, Nodes=1
- [ 0.000000@0] arch_multi_cluster:0
- [ 0.000000@0] Hierarchical RCU implementation.
- [ 0.000000@0] RCU debugfs-based tracing is enabled.
- [ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
- [ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
- [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
- [ 0.000000@0] clocksource_of_init: no matching clocksources found
- [ 0.000000@0] Kernel panic - not syncing: Unable to initialise architected timer.
- [ 0.000000@0]
- [ 0.000000@0] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.29 #1
- [ 0.000000@0] Call trace:
- [ 0.000000@0] [<ffffffc001087738>] dump_backtrace+0x0/0x160
- [ 0.000000@0] [<ffffffc0010878b8>] show_stack+0x20/0x30
- [ 0.000000@0] [<ffffffc00179ffc8>] dump_stack+0x78/0x94
- [ 0.000000@0] [<ffffffc00179c78c>] panic+0xe0/0x200
- [ 0.000000@0] [<ffffffc001c1e938>] time_init+0x1c/0x38
- [ 0.000000@0] [<ffffffc001c1c698>] start_kernel+0x214/0x354
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement