API tools faq
paste
mopv

Latest u-boot

mopv
May 30th, 2022 (edited)
83
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 14.24 KB | None | 0 0
raw download clone embed print report
  1. U-Boot 1.1.4 (Jul 27 2020 - 11:48:21)
  2.  
  3. ap152 - Dragonfly 1.0DRAM:
  4. sri
  5. ath_ddr_initial_config(278): (ddr2 init)
  6. ath_sys_frequency: cpu 775 ddr 650 ahb 258
  7. Tap values = (0xe, 0xe, 0xe, 0xe)
  8. 128 MB
  9. Top of RAM usable for U-Boot at: 88000000
  10. Reserving 492k for U-Boot at: 87f84000
  11. Reserving 192k for malloc() at: 87f54000
  12. Reserving 44 Bytes for Board Info at: 87f53fd4
  13. Reserving 36 Bytes for Global Data at: 87f53fb0
  14. Reserving 128k for boot params() at: 87f33fb0
  15. Stack Pointer at: 87f33f98
  16. Now running in RAM - U-Boot at: 87f84000
  17. Flash Manuf Id 0x20, DeviceId0 0x70, DeviceId1 0x18
  18. flash size 16MB, sector count = 256
  19. Flash: 16 MB
  20. *** Warning - bad CRC, using default environment
  21.  
  22. Power up PLL with outdiv = 0 then switch to 3
  23. In: serial
  24. Out: serial
  25. Err: serial
  26. Reading Partition Table from NVRAM ... OK
  27. Parsing Partition Table ... OK
  28. [NM_Error](nm_api_checkDefaultMac) 00483:
  29.  
  30. factory boot check kernel ok.
  31. Autobooting in 1 seconds
  32. Net: No valid address in Flash. Using fixed address
  33. athr_mgmt_init ::done
  34. Dragonfly ----> S17 PHY *
  35. athrs17_reg_init: complete
  36. SGMII in forced mode
  37. athr_gmac_sgmii_setup SGMII done
  38. : cfg1 0x80000000 cfg2 0x7114
  39. eth0: 00:03:7f:09:0b:ad
  40. eth0 up
  41. eth0
  42. Setting 0x181162c0 to 0x4b962100
  43. ath> setenv serverip 192.168.1.234
  44. ath> tftpboot 0x81000000 firm.bin
  45. Trying eth0
  46. dup 1 speed 1000
  47. Using eth0 device
  48. TFTP from server 192.168.1.234; our IP address is 192.168.1.1
  49. Filename 'firm.bin'.
  50. Load address: 0x81000000
  51. Loading: #################################################################
  52. #################################################################
  53. #################################################################
  54. #################################################################
  55. #################################################################
  56. #################################################################
  57. #################################################################
  58. #################################################################
  59. #################################################################
  60. #################################################################
  61. #################################################################
  62. #################################################################
  63. #################################################################
  64. ######################
  65. done
  66. Bytes transferred = 4438233 (43b8d9 hex)
  67. ath> bootm 0x81000000
  68. ## Booting image at 81000000 ...
  69. Image Name: MIPS OpenWrt Linux-4.14.254
  70. Created: 2021-11-28 21:36:42 UTC
  71. Image Type: MIPS Linux Kernel Image (lzma compressed)
  72. Data Size: 4438169 Bytes = 4.2 MB
  73. Load Address: 80060000
  74. Entry Point: 80060000
  75. Verifying Checksum at 0x81000040 ...OK
  76. Uncompressing Kernel Image ... OK
  77. No initrd
  78. ## Transferring control to Linux (at address 80060000) ...
  79. ## Giving linux memsize in bytes, 134217728
  80.  
  81. Starting kernel ...
  82.  
  83. [ 0.000000] Linux version 4.14.254 (morgle@morlge) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11391-de5cfab47d)) #0 Sun Nov 28 21:36:42 2021
  84. [ 0.000000] bootconsole [early0] enabled
  85. [ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
  86. [ 0.000000] MIPS: machine is TP-Link Deco M4R V1V2
  87. [ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
  88. [ 0.000000] Determined physical RAM map:
  89. [ 0.000000] memory: 08000000 @ 00000000 (usable)
  90. [ 0.000000] Initrd not found or empty - disabling initrd
  91. [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  92. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  93. [ 0.000000] Zone ranges:
  94. [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
  95. [ 0.000000] Movable zone start for each node
  96. [ 0.000000] Early memory node ranges
  97. [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
  98. [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
  99. [ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x47c with crng_init=0
  100. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
  101. [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/mtdblock2 rootfstype=squashfs,jffs2
  102. [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
  103. [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  104. [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  105. [ 0.000000] Writing ErrCtl register=00000000
  106. [ 0.000000] Readback ErrCtl register=00000000
  107. [ 0.000000] Memory: 114928K/131072K available (3837K kernel code, 146K rwdata, 920K rodata, 9424K init, 204K bss, 16144K reserved, 0K cma-reserved)
  108. [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  109. [ 0.000000] NR_IRQS: 51
  110. [ 0.000000] CPU clock: 775.000 MHz
  111. [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
  112. [ 0.000007] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
  113. [ 0.008224] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
  114. [ 0.074780] pid_max: default: 32768 minimum: 301
  115. [ 0.079801] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  116. [ 0.086785] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  117. [ 0.097575] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  118. [ 0.107967] futex hash table entries: 256 (order: -1, 3072 bytes)
  119. [ 0.114456] pinctrl core: initialized pinctrl subsystem
  120. [ 0.120764] NET: Registered protocol family 16
  121. [ 0.131201] PCI host bridge /ahb/pcie-controller@18250000 ranges:
  122. [ 0.137632] MEM 0x0000000012000000..0x0000000013ffffff
  123. [ 0.143169] IO 0x0000000000000000..0x0000000000000000
  124. [ 0.162507] PCI host bridge to bus 0000:00
  125. [ 0.166879] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
  126. [ 0.174116] pci_bus 0000:00: root bus resource [io 0x0000]
  127. [ 0.179995] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
  128. [ 0.187146] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
  129. [ 0.195901] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
  130. [ 0.205829] clocksource: Switched to clocksource MIPS
  131. [ 0.212016] NET: Registered protocol family 2
  132. [ 0.216811] IP idents hash table entries: 2048 (order: 2, 16384 bytes)
  133. [ 0.224139] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  134. [ 0.231536] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  135. [ 0.238260] TCP: Hash tables configured (established 1024 bind 1024)
  136. [ 0.245075] UDP hash table entries: 256 (order: 0, 4096 bytes)
  137. [ 0.251276] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  138. [ 0.258112] NET: Registered protocol family 1
  139. [ 0.414848] Crashlog allocated RAM at address 0x3f00000
  140. [ 0.421595] workingset: timestamp_bits=30 max_order=15 bucket_order=0
  141. [ 0.432408] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  142. [ 0.438598] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  143. [ 0.508648] io scheduler noop registered
  144. [ 0.512779] io scheduler deadline registered (default)
  145. [ 0.519853] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68
  146. [ 0.528125] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  147. [ 0.539871] m25p80 spi0.0: XM25QH128A (16384 Kbytes)
  148. [ 0.545143] 6 fixed-partitions partitions found on MTD device spi0.0
  149. [ 0.551879] Creating 6 MTD partitions on "spi0.0":
  150. [ 0.556947] 0x000000000000-0x000000080000 : "u-boot"
  151. [ 0.562830] 0x000000080000-0x000000085000 : "product-info"
  152. [ 0.569265] 0x000000085000-0x0000001f0000 : "config"
  153. [ 0.575127] 0x0000001f0000-0x0000002f0000 : "art"
  154. [ 0.580756] 0x000000200000-0x000000400000 : "kernel"
  155. [ 0.586638] 0x000000400000-0x000001000000 : "rootfs"
  156. [ 0.592438] mtd: device 5 (rootfs) set to be root filesystem
  157. [ 0.598496] 1 squashfs-split partitions found on MTD device rootfs
  158. [ 0.605022] 0x000000eb0000-0x000001000000 : "rootfs_data"
  159. [ 0.612279] libphy: Fixed MDIO Bus: probed
  160. [ 1.296173] libphy: ag71xx_mdio: probed
  161. [ 1.320412] switch0: Atheros AR8337 rev. 2 switch registered on mdio-bus.0
  162. [ 1.977299] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
  163. [ 1.989119] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
  164. [ 1.997412] NET: Registered protocol family 10
  165. [ 2.005937] Segment Routing with IPv6
  166. [ 2.009871] NET: Registered protocol family 17
  167. [ 2.014589] 8021q: 802.1Q VLAN Support v1.8
  168. [ 2.020572] Warning: unable to open an initial console.
  169. [ 2.077099] Freeing unused kernel memory: 9424K
  170. [ 2.081870] This architecture does not have kernel memory protection.
  171. [ 2.100391] init: Console is alive
  172. [ 2.104156] init: - watchdog -
  173. [ 2.125390] kmodloader: loading kernel modules from /etc/modules-boot.d/*
  174. [ 2.134880] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
  175. [ 2.153099] init: - preinit -
  176. [ 2.327839] random: jshn: uninitialized urandom read (4 bytes read)
  177. [ 2.401656] random: jshn: uninitialized urandom read (4 bytes read)
  178. [ 2.507741] random: jshn: uninitialized urandom read (4 bytes read)
  179. [ 3.397833] urandom_read: 4 callbacks suppressed
  180. [ 3.397840] random: procd: uninitialized urandom read (4 bytes read)
  181. [ 3.414582] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  182. [ 3.420849] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
  183. [ 4.507780] eth0: link up (1000Mbps/Full duplex)
  184. [ 4.512722] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  185. [ 4.528054] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
  186. [ 5.551297] eth0: link down
  187. [ 5.575029] procd: - early -
  188. [ 5.578273] procd: - watchdog -
  189. [ 5.605864] random: fast init done
  190. [ 6.130679] procd: - watchdog -
  191. [ 6.134152] procd: failed to set stdio: No such device
  192. [ 6.139675] procd: - ubus -
  193. [ 6.148365] random: ubusd: uninitialized urandom read (4 bytes read)
  194. [ 6.192984] random: ubusd: uninitialized urandom read (4 bytes read)
  195. [ 6.200900] procd: - init -
  196. [ 6.583259] kmodloader: loading kernel modules from /etc/modules.d/*
  197. [ 6.620913] ip6_tables: (C) 2000-2006 Netfilter Core Team
  198. [ 6.642160] Loading modules backported from Linux version v4.19.207-0-g2950c9c5e0df
  199. [ 6.650280] Backport generated by backports.git v4.19.207-1-0-gb4d7efee
  200. [ 6.677782] ip_tables: (C) 2000-2006 Netfilter Core Team
  201. [ 6.702262] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
  202. [ 6.799844] xt_time: kernel timezone is -0000
  203. [ 6.900504] urngd: v1.0.2 started.
  204. [ 6.910293] PPP generic driver version 2.4.2
  205. [ 6.916957] NET: Registered protocol family 24
  206. [ 6.978869] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x56.
  207. [ 7.006574] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
  208. [ 7.012837] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
  209. [ 7.089673] random: crng init done
  210. [ 7.229015] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:00:00.0.txt failed with error -2
  211. [ 7.240157] ath10k_pci 0000:00:00.0: Falling back to user helper
  212. [ 7.425087] firmware ath10k!fwcfg-pci-0000:00:00.0.txt: firmware_loading_store: map pages failed
  213. [ 7.434614] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
  214. [ 7.445921] ath10k_pci 0000:00:00.0: Falling back to user helper
  215. [ 7.987160] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9888/hw2.0/ct-firmware-5.bin failed with error -2
  216. [ 7.998750] ath10k_pci 0000:00:00.0: Falling back to user helper
  217. [ 8.271064] firmware ath10k!QCA9888!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
  218. [ 8.281046] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9888/hw2.0/ct-firmware-2.bin failed with error -2
  219. [ 8.292624] ath10k_pci 0000:00:00.0: Falling back to user helper
  220. [ 8.609652] firmware ath10k!QCA9888!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
  221. [ 8.619637] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9888/hw2.0/firmware-6.bin failed with error -2
  222. [ 8.630938] ath10k_pci 0000:00:00.0: Falling back to user helper
  223. [ 8.815537] firmware ath10k!QCA9888!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
  224. [ 8.830912] ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
  225. [ 8.840659] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
  226. [ 8.860742] ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-13-8c5b2baa2 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 cbf49903
  227. [ 9.274253] ath10k_pci 0000:00:00.0: board_file api 2 bmi_id 0:24 crc32 f228337a
  228. [ 11.330702] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
  229. [ 11.338630] ath10k_pci 0000:00:00.0: msdu-desc: 2500 skid: 32
  230. [ 11.388510] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
  231. [ 11.400049] ath10k_pci 0000:00:00.0: wmi print 'free: 114572 iram: 12804 sram: 29508'
  232. [ 11.611091] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
  233. [ 11.794925] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=2
  234. [ 11.841936] kmodloader: done loading kernel modules from /etc/modules.d/*
  235. [ 50.968063] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  236. [ 50.998835] br-lan: port 1(eth0.1) entered blocking state
  237. [ 51.004529] br-lan: port 1(eth0.1) entered disabled state
  238. [ 51.010520] device eth0.1 entered promiscuous mode
  239. [ 51.015568] device eth0 entered promiscuous mode
  240. [ 51.086054] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  241. [ 52.027456] eth0: link up (1000Mbps/Full duplex)
  242. [ 52.032398] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  243. [ 52.059297] br-lan: port 1(eth0.1) entered blocking state
  244. [ 52.064990] br-lan: port 1(eth0.1) entered forwarding state
  245. [ 52.085179] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  246.  
  247.  
Add Comment
Please, Sign In to add comment
Public Pastes
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!