00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-

Latency: 64

Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]

Capabilities: [a0] AGP version 1.0

Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2

Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

Kernel driver in use: agpgart-intel

Kernel modules: intel-agp



00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 64

Bus: primary=00, secondary=01, subordinate=03, sec-latency=64

I/O behind bridge: 00001000-00002fff

Memory behind bridge: f0000000-f02fffff

Prefetchable memory behind bridge: 30000000-301fffff

Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-

BridgeCtl: Parity+ SERR- NoISA- VGA- MAbort- >Reset- FastB2B+

PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

Kernel modules: shpchp



00:07.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0



00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])

Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 64

Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]

Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]

Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]

Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]

Region 4: I/O ports at 3400 [size=16]

Kernel driver in use: PIIX_IDE

Kernel modules: piix



00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])

Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 64

Interrupt: pin D routed to IRQ 5

Region 4: I/O ports at 3420 [size=32]

Kernel driver in use: uhci_hcd

Kernel modules: uhci-hcd



00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)

Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Interrupt: pin ? routed to IRQ 9

Kernel driver in use: piix4_smbus

Kernel modules: i2c-piix4



00:0d.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41)

Subsystem: Device aa55:aa55

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 64 (5000ns min, 10000ns max)

Interrupt: pin A routed to IRQ 9

Region 0: I/O ports at 3000 [size=128]

Region 1: Memory at f0380000 (32-bit, non-prefetchable) [size=1K]

[virtual] Expansion ROM at 30200000 [disabled] [size=256K]

Kernel driver in use: tulip

Kernel modules: tulip



00:0e.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41)

Subsystem: Device aa55:aa55

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 64 (5000ns min, 10000ns max)

Interrupt: pin A routed to IRQ 5

Region 0: I/O ports at 3080 [size=128]

Region 1: Memory at f0380400 (32-bit, non-prefetchable) [size=1K]

[virtual] Expansion ROM at 30240000 [disabled] [size=256K]

Kernel driver in use: tulip

Kernel modules: tulip



00:0f.0 CardBus bridge: Texas Instruments PCI1225 (rev 01)

Subsystem: Nokia Telecommunications oy Device 0000

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 168, Cache Line Size: 32 bytes

Interrupt: pin A routed to IRQ 10

Region 0: Memory at 30280000 (32-bit, non-prefetchable) [size=4K]

Bus: primary=00, secondary=04, subordinate=07, sec-latency=176

Memory window 0: 20000000-23fff000 (prefetchable)

Memory window 1: 24000000-27fff000

I/O window 0: 00003800-000038ff

I/O window 1: 00003c00-00003cff

BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+

16-bit legacy interface ports at 0001

Kernel driver in use: yenta_cardbus

Kernel modules: yenta_socket



00:0f.1 CardBus bridge: Texas Instruments PCI1225 (rev 01)

Subsystem: Nokia Telecommunications oy Device 0000

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 168, Cache Line Size: 32 bytes

Interrupt: pin B routed to IRQ 11

Region 0: Memory at 30281000 (32-bit, non-prefetchable) [size=4K]

Bus: primary=00, secondary=08, subordinate=0b, sec-latency=176

Memory window 0: 28000000-2bfff000 (prefetchable)

Memory window 1: 2c000000-2ffff000

I/O window 0: 00004000-000040ff

I/O window 1: 00004400-000044ff

BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+

16-bit legacy interface ports at 0001

Kernel driver in use: yenta_cardbus

Kernel modules: yenta_socket



01:00.0 PCI bridge: Digital Equipment Corporation DECchip 21150 (rev 06) (prog-if 00 [Normal decode])

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 64, Cache Line Size: 64 bytes

Bus: primary=01, secondary=02, subordinate=03, sec-latency=64

I/O behind bridge: 00001000-00002fff

Memory behind bridge: f0000000-f02fffff

Prefetchable memory behind bridge: 0000000030000000-00000000301fffff

Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-

BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-

PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

Capabilities: [dc] Power Management version 1

Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)

Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Bridge: PM- B3+

Kernel modules: shpchp



02:04.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41)

Subsystem: Device aa55:aa55

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 64 (5000ns min, 10000ns max)

Interrupt: pin A routed to IRQ 10

Region 0: I/O ports at 2000 [size=128]

Region 1: Memory at f0280000 (32-bit, non-prefetchable) [size=1K]

[virtual] Expansion ROM at 30100000 [disabled] [size=256K]

Kernel driver in use: tulip

Kernel modules: tulip



02:05.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41)

Subsystem: Device aa55:aa55

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 64 (5000ns min, 10000ns max)

Interrupt: pin A routed to IRQ 11

Region 0: I/O ports at 2080 [size=128]

Region 1: Memory at f0280400 (32-bit, non-prefetchable) [size=1K]

[virtual] Expansion ROM at 30140000 [disabled] [size=256K]

Kernel driver in use: tulip

Kernel modules: tulip



02:06.0 PCI bridge: Intel Corporation 21154 PCI-to-PCI Bridge (prog-if 00 [Normal decode])

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 64, Cache Line Size: 64 bytes

Bus: primary=02, secondary=03, subordinate=03, sec-latency=64

I/O behind bridge: 00001000-00001fff

Memory behind bridge: f0000000-f01fffff

Prefetchable memory behind bridge: 0000000030000000-00000000300fffff

Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-

BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-

PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

Capabilities: [dc] Power Management version 1

Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)

Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Bridge: PM- B3+

Kernel modules: shpchp



03:04.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41)

Subsystem: Device 0040:61e0

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 64 (5000ns min, 10000ns max)

Interrupt: pin A routed to IRQ 0

Region 0: I/O ports at 1000 [size=128]

Region 1: Memory at f0100000 (32-bit, non-prefetchable) [size=1K]

[virtual] Expansion ROM at 30000000 [disabled] [size=256K]

Kernel driver in use: tulip

Kernel modules: tulip



03:05.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41)

Subsystem: Device 0040:61e0

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 64 (5000ns min, 10000ns max)

Interrupt: pin A routed to IRQ 0

Region 0: I/O ports at 1080 [size=128]

Region 1: Memory at f0100400 (32-bit, non-prefetchable) [size=1K]

[virtual] Expansion ROM at 30040000 [disabled] [size=256K]

Kernel driver in use: tulip

Kernel modules: tulip



03:06.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41)

Subsystem: Device 0040:61e0

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 64 (5000ns min, 10000ns max)

Interrupt: pin A routed to IRQ 0

Region 0: I/O ports at 1400 [size=128]

Region 1: Memory at f0100800 (32-bit, non-prefetchable) [size=1K]

[virtual] Expansion ROM at 30080000 [disabled] [size=256K]

Kernel driver in use: tulip

Kernel modules: tulip



03:07.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41)

Subsystem: Device 0040:61e0

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 64 (5000ns min, 10000ns max)

Interrupt: pin A routed to IRQ 0

Region 0: I/O ports at 1480 [size=128]

Region 1: Memory at f0100c00 (32-bit, non-prefetchable) [size=1K]

[virtual] Expansion ROM at 300c0000 [disabled] [size=256K]

Kernel driver in use: tulip

Kernel modules: tulip