Guest User

loboris image with adjusted script.bin

a guest
Nov 26th, 2015
103
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. HELLO! BOOT0 is starting!
  2. boot0 version : 4.0.0
  3. fel_flag = 0x00000000
  4. rtc[0] value = 0x00000000
  5. rtc[1] value = 0x00000000
  6. rtc[2] value = 0x00000000
  7. rtc[3] value = 0x00000000
  8. rtc[4] value = 0x00000000
  9. rtc[5] value = 0x00000000
  10. rtc[6] value = 0x00000000
  11. rtc[7] value = 0x00000000
  12. DRAM DRIVE INFO: V0.8
  13. DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
  14. DRAM CLK = 672 MHz
  15. DRAM zq value: 003b3bfb
  16. READ DQS LCDL = 001d1c1d
  17. DRAM SIZE =1024 M
  18. odt delay
  19. dram size =1024
  20. card boot number = 0
  21. card no is 0
  22. sdcard 0 line count 4
  23. [mmc]: mmc driver ver 2014-12-10 21:20:39
  24. [mmc]: ***Try SD card 0***
  25. [mmc]: SD/MMC Card: 4bit, capacity: 7580MB
  26. [mmc]: vendor: Man 00035344 Snr 1013290e
  27. [mmc]: product: SU08G
  28. [mmc]: revision: 8.0
  29. [mmc]: ***SD/MMC 0 init OK!!!***
  30. sdcard 0 init ok
  31. The size of uboot is 000dc000.
  32. sum=ede66ee7
  33. src_sum=ede66ee7
  34. Succeed in loading uboot from sdmmc flash.
  35. Ready to disable icache.
  36. Jump to secend Boot.
  37. SUNXI_NORMAL_MODE
  38. [ 0.362]e mode
  39.  
  40. U-Boot 2011.09-rc1 (Jun 21 2015 - 19:33:17) Allwinner Technology
  41.  
  42. [ 0.369]version: 1.1.0
  43. normal mode
  44. [ 0.376]pmbus: ready
  45. not set main pmu id
  46. axp_probe error
  47. [ 0.391]PMU: pll1 1200 Mhz,PLL6=600 Mhz
  48. AXI=400 Mhz,AHB=200 Mhz, APB1=100 Mhz
  49. sid read already
  50. fel key new mode
  51. run key detect
  52. no key found
  53. no key input
  54. dram_para_set start
  55. dram_para_set end
  56. normal mode
  57. [ 0.422]DRAM: 1 GiB
  58. relocation Offset is: 35af9000
  59. [box standby] read rtc = 0x0
  60. [box_start_os] mag be start_type no use
  61. user_gpio config
  62. user_gpio ok
  63. gic: normal or no secure os mode
  64. workmode = 0
  65. MMC: 0
  66. [ 0.496][mmc]: mmc driver ver 2014-12-10 9:23:00
  67. [ 0.501][mmc]: get sdc_phy_wipe fail.
  68. [ 0.505][mmc]: get sdc0 sdc_erase fail.
  69. [ 0.509][mmc]: get sdc_f_max fail,use default 50000000Hz
  70. [ 0.514][mmc]: get sdc_ex_dly_used fail,use default dly
  71. [ 0.520][mmc]: SUNXI SD/MMC: 0
  72. [ 0.533][mmc]: *Try SD card 0*
  73. [ 0.580][mmc]: CID 0x3534453 0x55303847 0x80101329 0xe00d669
  74. [ 0.585][mmc]: mmc clk 50000000
  75. [ 0.588][mmc]: SD/MMC Card: 4bit, capacity: 7580MB
  76. [ 0.593][mmc]: boot0 capacity: 0KB,boot1 capacity: 0KB
  77. [ 0.599][mmc]: ***SD/MMC 0 init OK!!!***
  78. [ 0.603][mmc]: erase_grp_size:0x1WrBlk * 0x200 = 0x200 Byte
  79. [ 0.609][mmc]: secure_feature 0x0
  80. [ 0.612][mmc]: secure_removal_type 0x0
  81. [ 0.616]sunxi flash init ok
  82. script config pll_de to 864 Mhz
  83. Not Found clk pll_video1 in script
  84. script config pll_video to 297 Mhz
  85. [boot]disp_init_tv
  86. [DISP_TV] disp_init_tv enter g_tv_used
  87. screen 0 do not support TV TYPE!
  88. [BOOOT_DISP_TV] disp tv device_registered
  89. unable to find regulator vcc-hdmi-18 from [pmu1_regu] or [pmu2_regu]
  90. enable power vcc-hdmi-18, ret=-1
  91. DRV_DISP_Init end
  92. boot_disp.auto_hpd=1
  93. auto hpd check has 100 times!
  94. auto check no any connected, the output_type is 4
  95. [disk_read_fs] no the partition
  96. error: open disp_rsl.fex, maybe it is not exist
  97. not support this mode[4], use inline mode[4]
  98. attched ok, mgr0<-->device0, type=4, mode=4----
  99. ready to set mode
  100. [ 1.997]finally, output_type=0x4, output_mode=0x4, screen_id=0x0, disp_para=0x0
  101. fail to find part named env
  102. Using default environment
  103.  
  104. In: serial
  105. Out: serial
  106. Err: serial
  107. --------fastboot partitions--------
  108. mbr not exist
  109. base bootcmd=run setargs_mmc boot_normal
  110. bootcmd set setargs_mmc
  111. key 0
  112. cant find rcvy value
  113. cant find fstbt value
  114. no misc partition is found
  115. to be run cmd=run setargs_mmc boot_normal
  116. [ 2.034][mmc]: MMC Device 2 not found
  117. [ 2.038][mmc]: Can not find mmc dev
  118. [ 2.041][mmc]: read first backup failed in fun sdmmc_secure_storage_read line 1849
  119. sunxi_secstorage_read fail
  120. get secure storage map err
  121. the private part isn't exist
  122. WORK_MODE_BOOT
  123. adver not need show
  124. sunxi_bmp_logo_display
  125. [disk_read_fs] no the partition
  126. error: open bootlogo.bmp, maybe it is not exist
  127. sunxi bmp info error : unable to open logo file bootlogo.bmp
  128. [ 2.074]Hit any key to stop autoboot: 0
  129. [ 5.334][mmc]: blkcnt should not be 0
  130. [ 5.804][mmc]: blkcnt should not be 0
  131. ## Booting kernel from Legacy Image at 40007800 ...
  132. Image Name: Linux-3.4.39
  133. Image Type: ARM Linux Kernel Image (uncompressed)
  134. Data Size: 10915552 Bytes = 10.4 MiB
  135. Load Address: 40008000
  136. Entry Point: 40008000
  137. Verifying Checksum ... OK
  138. Loading Kernel Image ... OK
  139. OK
  140. [ 5.996][mmc]: MMC Device 2 not found
  141. [ 5.999][mmc]: mmc not find,so not exit
  142. [ 6.004]
  143. Starting kernel ...
  144.  
  145. [sun8i_fixup]: From boot, get meminfo:
  146. Start: 0x40000000
  147. Size: 1024MB
  148. ion_carveout reserve: 160m@0 256m@0 130m@1 200m@1
  149. ion_reserve_common: ion reserve: [0x70000000, 0x80000000]!
  150. [ 0.000000] Booting Linux on physical CPU 0
  151. [ 0.000000] Initializing cgroup subsys cpu
  152. [ 0.000000] Linux version 3.4.39 (boris@UbuntuMate) (gcc version 4.6.3 20120201 (prerelease) (crosstool-NG linaro-1.13.1-2012.02-20120222 - Linaro GCC 5
  153. [ 0.000000] Ignoring tag cmdline (using the default kernel command line)
  154. [ 0.000000] bootconsole [earlycon0] enabled
  155. [ 0.000000] cma: CMA: reserved 256 MiB at 70000000
  156. [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
  157. [ 0.000000] On node 0 totalpages: 262144
  158. [ 0.000000] free_area_init_node: node 0, pgdat c1000cc0, node_mem_map c10dd000
  159. [ 0.000000] Normal zone: 1710 pages used for memmap
  160. [ 0.000000] Normal zone: 0 pages reserved
  161. [ 0.000000] Normal zone: 192850 pages, LIFO batch:31
  162. [ 0.000000] HighMem zone: 594 pages used for memmap
  163. [ 0.000000] HighMem zone: 66990 pages, LIFO batch:15
  164. [ 0.000000] script_init enter!
  165. [ 0.000000] script_init exit!
  166. [ 0.000000] PERCPU: Embedded 8 pages/cpu @c19f3000 s11840 r8192 d12736 u32768
  167. [ 0.000000] pcpu-alloc: s11840 r8192 d12736 u32768 alloc=8*4096
  168. [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
  169. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259840
  170. [ 0.000000] Kernel command line: earlyprintk=ttyS0,115200 loglevel=8 initcall_debug=0 console=ttyS0,115200 console=tty0 init=/init
  171. [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
  172. [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  173. [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  174. [ 0.000000] Memory: 1024MB = 1024MB total
  175. [ 0.000000] Memory: 758680k/758680k available, 289896k reserved, 8192K highmem
  176. [ 0.000000] Virtual kernel memory layout:
  177. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  178. [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  179. [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
  180. [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
  181. [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  182. [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  183. [ 0.000000] .text : 0xc0008000 - 0xc0986378 (9721 kB)
  184. [ 0.000000] .init : 0xc0987000 - 0xc0f86e40 (6144 kB)
  185. [ 0.000000] .data : 0xc0f88000 - 0xc1003738 ( 494 kB)
  186. [ 0.000000] .bss : 0xc1003eec - 0xc10dc400 ( 866 kB)
  187. [ 0.000000] Preemptible hierarchical RCU implementation.
  188. [ 0.000000] Additional per-CPU info printed with stalls.
  189. [ 0.000000] NR_IRQS:544
  190. [ 0.000000] Architected local timer running at 24.00MHz.
  191. [ 0.000000] Switching to timer-based delay loop
  192. [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
  193. [ 0.000000] Console: colour dummy device 80x30
  194. [ 0.000000] console [tty0] enabled, bootconsole disabled
  195. [ 0.000000] Booting Linux on physical CPU 0
  196. [ 0.000000] Initializing cgroup subsys cpu
  197. [ 0.000000] Linux version 3.4.39 (boris@UbuntuMate) (gcc version 4.6.3 20120201 (prerelease) (crosstool-NG linaro-1.13.1-2012.02-20120222 - Linaro GCC 5
  198. [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
  199. [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  200. [ 0.000000] Machine: sun8i
  201. [ 0.000000] Ignoring tag cmdline (using the default kernel command line)
  202. [ 0.000000] bootconsole [earlycon0] enabled
  203. [ 0.000000] cma: CMA: reserved 256 MiB at 70000000
  204. [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
  205. [ 0.000000] On node 0 totalpages: 262144
  206. [ 0.000000] free_area_init_node: node 0, pgdat c1000cc0, node_mem_map c10dd000
  207. [ 0.000000] Normal zone: 1710 pages used for memmap
  208. [ 0.000000] Normal zone: 0 pages reserved
  209. [ 0.000000] Normal zone: 192850 pages, LIFO batch:31
  210. [ 0.000000] HighMem zone: 594 pages used for memmap
  211. [ 0.000000] HighMem zone: 66990 pages, LIFO batch:15
  212. [ 0.000000] script_init enter!
  213. [ 0.000000] script_init exit!
  214. [ 0.000000] PERCPU: Embedded 8 pages/cpu @c19f3000 s11840 r8192 d12736 u32768
  215. [ 0.000000] pcpu-alloc: s11840 r8192 d12736 u32768 alloc=8*4096
  216. [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
  217. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259840
  218. [ 0.000000] Kernel command line: earlyprintk=ttyS0,115200 loglevel=8 initcall_debug=0 console=ttyS0,115200 console=tty0 init=/init
  219. [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
  220. [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  221. [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  222. [ 0.000000] Memory: 1024MB = 1024MB total
  223. [ 0.000000] Memory: 758680k/758680k available, 289896k reserved, 8192K highmem
  224. [ 0.000000] Virtual kernel memory layout:
  225. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  226. [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  227. [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
  228. [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
  229. [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  230. [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  231. [ 0.000000] .text : 0xc0008000 - 0xc0986378 (9721 kB)
  232. [ 0.000000] .init : 0xc0987000 - 0xc0f86e40 (6144 kB)
  233. [ 0.000000] .data : 0xc0f88000 - 0xc1003738 ( 494 kB)
  234. [ 0.000000] .bss : 0xc1003eec - 0xc10dc400 ( 866 kB)
  235. [ 0.000000] Preemptible hierarchical RCU implementation.
  236. [ 0.000000] Additional per-CPU info printed with stalls.
  237. [ 0.000000] NR_IRQS:544
  238. [ 0.000000] Architected local timer running at 24.00MHz.
  239. [ 0.000000] Switching to timer-based delay loop
  240. [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
  241. [ 0.000000] Console: colour dummy device 80x30
  242. [ 0.000000] console [tty0] enabled, bootconsole disabled
  243. [ 0.019915] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
  244. [ 0.019969] pid_max: default: 32768 minimum: 301
  245. [ 0.020242] Mount-cache hash table entries: 512
  246. [ 0.021126] Initializing cgroup subsys cpuacct
  247. [ 0.021154] Initializing cgroup subsys freezer
  248. [ 0.021201] CPU: Testing write buffer coherency: ok
  249. [ 0.021257] ftrace: allocating 26203 entries in 77 pages
  250. [ 0.050267] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
  251. [ 0.050300] [sunxi_smp_prepare_cpus] enter
  252. [ 0.050341] Setting up static identity map for 0x406d2af0 - 0x406d2b48
  253. [ 0.051180] CPU1: Booted secondary processor
  254. [ 0.051180] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
  255. [ 0.051312] CPU2: Booted secondary processor
  256. [ 0.051312] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
  257. [ 0.051312] CPU3: Booted secondary processor
  258. [ 0.051312] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
  259. [ 0.060173] Brought up 4 CPUs
  260. [ 0.060255] SMP: Total of 4 processors activated (19200.00 BogoMIPS).
  261. [ 0.060837] devtmpfs: initialized
  262. [ 0.063132] wakeup src cnt is : 1.
  263. [ 0.063151] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800000
  264. [ 0.063174] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x0
  265. [ 0.063198] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x40
  266. [ 0.063223] sunxi pm init
  267. [ 0.063353] pinctrl core: initialized pinctrl subsystem
  268. [ 0.073917] NET: Registered protocol family 16
  269. [ 0.074576] DMA: preallocated 2048 KiB pool for atomic coherent allocations
  270. [ 0.074576] script_sysfs_init success
  271. [ 0.074576] sunxi_dump_init success
  272. [ 0.074576] gpiochip_add: registered GPIOs 0 to 383 on device: sunxi-pinctrl
  273. [ 0.074576] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
  274. [ 0.074576] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
  275. [ 0.074576] hw-breakpoint: maximum watchpoint size is 8 bytes.
  276. [ 0.074576] script config pll_video to 297 Mhz
  277. [ 0.074576] script config pll_de to 864 Mhz
  278. [ 0.074576] script config pll_ve to 402 Mhz
  279. [ 0.074576] sunxi_default_clk_init
  280. [ 0.074576] try to set pll6ahb1 to 200000000
  281. [ 0.074576] try to set ahb clk source to pll6ahb1
  282. [ 0.074576] set ahb clk source to pll6ahb1
  283. [ 0.074576] try to set ahb1 to 200000000
  284. [ 0.074576] try to set apb1 to 100000000
  285. [ 0.074805] ===fe3o4==== sunxi_root_procfs_attach ret:0
  286. [ 0.080306] bio: create slab <bio-0> at 0
  287. [ 0.080365] [ARISC] :sunxi-arisc driver v1.04
  288. [ 0.095026] [ARISC] :arisc version: [v0.1.34]
  289. [ 0.183127] [ARISC] :sunxi-arisc driver v1.04 startup succeeded
  290. [ 0.190384] SCSI subsystem initialized
  291. [ 0.190570] usbcore: registered new interface driver usbfs
  292. [ 0.190648] usbcore: registered new interface driver hub
  293. [ 0.190686] usbcore: registered new device driver usb
  294. [ 0.190686] twi_chan_cfg()335 - [twi0] has no twi_regulator.
  295. [ 0.190686] twi_chan_cfg()335 - [twi1] has no twi_regulator.
  296. [ 0.190686] twi_chan_cfg()335 - [twi2] has no twi_regulator.
  297. [ 0.190720] Linux video capture interface: v2.00
  298. [ 0.190911] Advanced Linux Sound Architecture Driver Version 1.0.25.
  299. [ 0.191391] Bluetooth: Core ver 2.16
  300. [ 0.191438] NET: Registered protocol family 31
  301. [ 0.191459] Bluetooth: HCI device and connection manager initialized
  302. [ 0.191487] Bluetooth: HCI socket layer initialized
  303. [ 0.191509] Bluetooth: L2CAP socket layer initialized
  304. [ 0.191549] Bluetooth: SCO socket layer initialized
  305. [ 0.191755] cfg80211: Calling CRDA to update world regulatory domain
  306. [ 0.191833] Switching to clocksource arch_sys_counter
  307. [ 0.202029] FS-Cache: Loaded
  308. [ 0.202309] CacheFiles: Loaded
  309. [ 0.212154] NET: Registered protocol family 2
  310. [ 0.212416] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
  311. [ 0.212942] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
  312. [ 0.214556] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
  313. [ 0.215348] TCP: Hash tables configured (established 131072 bind 65536)
  314. [ 0.215372] TCP: reno registered
  315. [ 0.215392] UDP hash table entries: 512 (order: 2, 16384 bytes)
  316. [ 0.215436] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  317. [ 0.215706] NET: Registered protocol family 1
  318. [ 0.216049] RPC: Registered named UNIX socket transport module.
  319. [ 0.216075] RPC: Registered udp transport module.
  320. [ 0.216093] RPC: Registered tcp transport module.
  321. [ 0.216111] RPC: Registered tcp NFSv4.1 backchannel transport module.
  322. [ 0.554815] hw perfevents: enabled with ARMv7 Cortex_A7 PMU driver, 5 counters available
  323. [ 0.554963] sunxi_reg_init enter
  324. [ 0.555688] audit: initializing netlink socket (disabled)
  325. [ 0.555749] type=2000 audit(0.550:1): initialized
  326. [ 0.558836] highmem bounce pool size: 64 pages
  327. [ 0.559780] NFS: Registering the id_resolver key type
  328. [ 0.560153] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
  329. [ 0.560813] NTFS driver 2.1.30 [Flags: R/W].
  330. [ 0.560938] fuse init (API version 7.18)
  331. [ 0.561699] Btrfs loaded
  332. [ 0.561733] msgmni has been set to 1465
  333. [ 0.562753] io scheduler noop registered
  334. [ 0.562778] io scheduler deadline registered
  335. [ 0.562863] io scheduler cfq registered (default)
  336. [ 0.563237] [DISP]disp_module_init
  337. [ 0.563516] cmdline,disp=
  338. [ 0.580973] [DISP] Fb_map_kernel_logo,line:925:Fb_map_kernel_logo failed!
  339. [ 0.608775] Console: switching to colour frame buffer device 240x67
  340. [ 0.637390] [DISP]disp_module_init finish
  341. [ 0.637675] sw_uart_get_devinfo()1503 - uart0 has no uart_regulator.
  342. [ 0.637827] sw_uart_get_devinfo()1503 - uart2 has no uart_regulator.
  343. [ 0.637974] sw_uart_get_devinfo()1503 - uart3 has no uart_regulator.
  344. [ 0.638523] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
  345. [ 0.638667] sw_uart_pm()890 - uart0 clk is already enable
  346. [ 0.638798] sw_console_setup()1233 - console setup baud 115200 parity n bits 8, flow n
  347. [ 0.734765] console [ttyS0] enabled
  348. [ 1.322823] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI
  349. [ 1.323090] uart3: ttyS3 at MMIO 0x1c28c00 (irq = 35) is a SUNXI
  350. [ 1.323584] sunxi_cmatest_init enter
  351. [ 1.323616] sunxi_cmatest_init success
  352. [ 1.327297] loop: module loaded
  353. [ 1.520155] sunxi_spi_chan_cfg()1355 - [spi-0] has no spi_regulator.
  354. [ 1.520166] sunxi_spi_chan_cfg()1355 - [spi-1] has no spi_regulator.
  355. [ 1.520667] spi spi0: master is unqueued, this is deprecated
  356. [ 1.520932] tun: Universal TUN/TAP device driver, 1.6
  357. [ 1.520939] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  358. [ 1.521714] PPP generic driver version 2.4.2
  359. [ 1.521887] PPP BSD Compression module registered
  360. [ 1.521894] PPP Deflate Compression module registered
  361. [ 1.524069] PPP MPPE Compression module registered
  362. [ 1.524083] NET: Registered protocol family 24
  363. [ 1.524123] PPTP driver version 0.8.5
  364. [ 1.524325] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  365. [ 1.544425] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  366. [ 1.544456] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1
  367. [ 1.701745] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
  368. [ 1.900031] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
  369. [ 2.097048] hub 1-0:1.0: USB hub found
  370. [ 2.278402] hub 1-0:1.0: 1 port detected
  371. [ 2.456380] sunxi-ehci sunxi-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  372. [ 2.471059] sunxi-ehci sunxi-ehci.2: new USB bus registered, assigned bus number 2
  373. [ 2.485597] sunxi-ehci sunxi-ehci.2: irq 106, io mem 0xf1c1b000
  374. [ 2.510028] sunxi-ehci sunxi-ehci.2: USB 0.0 started, EHCI 1.00
  375. [ 2.522818] hub 2-0:1.0: USB hub found
  376. [ 2.532768] hub 2-0:1.0: 1 port detected
  377. [ 2.563105] sunxi-ehci sunxi-ehci.3: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  378. [ 2.577752] sunxi-ehci sunxi-ehci.3: new USB bus registered, assigned bus number 3
  379. [ 2.592219] sunxi-ehci sunxi-ehci.3: irq 108, io mem 0xf1c1c000
  380. [ 2.620041] sunxi-ehci sunxi-ehci.3: USB 0.0 started, EHCI 1.00
  381. [ 2.632733] hub 3-0:1.0: USB hub found
  382. [ 2.642539] hub 3-0:1.0: 1 port detected
  383. [ 2.672765] sunxi-ehci sunxi-ehci.4: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  384. [ 2.687313] sunxi-ehci sunxi-ehci.4: new USB bus registered, assigned bus number 4
  385. [ 2.701729] sunxi-ehci sunxi-ehci.4: irq 110, io mem 0xf1c1d000
  386. [ 2.730037] sunxi-ehci sunxi-ehci.4: USB 0.0 started, EHCI 1.00
  387. [ 2.742771] hub 4-0:1.0: USB hub found
  388. [ 2.752652] hub 4-0:1.0: 1 port detected
  389. [ 2.762916] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  390. [ 2.795411] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
  391. [ 2.809579] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 5
  392. [ 2.823660] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400
  393. [ 2.894469] hub 5-0:1.0: USB hub found
  394. [ 2.904264] hub 5-0:1.0: 1 port detected
  395. [ 2.934458] sunxi-ohci sunxi-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
  396. [ 2.948625] sunxi-ohci sunxi-ohci.2: new USB bus registered, assigned bus number 6
  397. [ 2.962815] sunxi-ohci sunxi-ohci.2: irq 107, io mem 0xf1c1b400
  398. [ 3.034476] hub 6-0:1.0: USB hub found
  399. [ 3.044332] hub 6-0:1.0: 1 port detected
  400. [ 3.074657] sunxi-ohci sunxi-ohci.3: SW USB2.0 'Open' Host Controller (OHCI) Driver
  401. [ 3.088990] sunxi-ohci sunxi-ohci.3: new USB bus registered, assigned bus number 7
  402. [ 3.103271] sunxi-ohci sunxi-ohci.3: irq 109, io mem 0xf1c1c400
  403. [ 3.174468] hub 7-0:1.0: USB hub found
  404. [ 3.184483] hub 7-0:1.0: 1 port detected
  405. [ 3.214909] sunxi-ohci sunxi-ohci.4: SW USB2.0 'Open' Host Controller (OHCI) Driver
  406. [ 3.229275] sunxi-ohci sunxi-ohci.4: new USB bus registered, assigned bus number 8
  407. [ 3.243528] sunxi-ohci sunxi-ohci.4: irq 111, io mem 0xf1c1d400
  408. [ 3.314488] hub 8-0:1.0: USB hub found
  409. [ 3.324487] hub 8-0:1.0: 1 port detected
  410. [ 3.335003] Initializing USB Mass Storage driver...
  411. [ 3.346454] usbcore: registered new interface driver usb-storage
  412. [ 3.358989] USB Mass Storage support registered.
  413. [ 3.369974] usbcore: registered new interface driver ums-alauda
  414. [ 3.382393] usbcore: registered new interface driver ums-cypress
  415. [ 3.394832] usbcore: registered new interface driver ums-datafab
  416. [ 3.407272] usbcore: registered new interface driver ums_eneub6250
  417. [ 3.419843] usbcore: registered new interface driver ums-freecom
  418. [ 3.432281] usbcore: registered new interface driver ums-isd200
  419. [ 3.444544] usbcore: registered new interface driver ums-jumpshot
  420. [ 3.456927] usbcore: registered new interface driver ums-karma
  421. [ 3.469022] usbcore: registered new interface driver ums-onetouch
  422. [ 3.481358] usbcore: registered new interface driver ums-realtek
  423. [ 3.493519] usbcore: registered new interface driver ums-sddr09
  424. [ 3.505516] usbcore: registered new interface driver ums-sddr55
  425. [ 3.517432] usbcore: registered new interface driver ums-usbat
  426. [ 3.529273] usbcore: registered new interface driver usbserial
  427. [ 3.540968] usbserial: USB Serial Driver core
  428. [ 3.551050] usbcore: registered new interface driver option
  429. [ 3.562503] USB Serial support registered for GSM modem (1-port)
  430. [ 3.575024] file system registered
  431. [ 3.585597] android_usb gadget: Mass Storage Function, version: 2009/09/11
  432. [ 3.598536] android_usb gadget: Number of LUNs=3
  433. [ 3.608878] lun0: LUN: removable file: (no medium)
  434. [ 3.619506] lun1: LUN: removable file: (no medium)
  435. [ 3.630094] lun2: LUN: removable file: (no medium)
  436. [ 3.640894] android_usb gadget: android_usb ready
  437. [ 3.651446] uinput result 0 , vmouse_init
  438. [ 3.661664] mousedev: PS/2 mouse device common for all mice
  439. [ 3.673144] sunxikbd_init failed.
  440. [ 3.681965] ls_fetch_sysconfig_para: type err device_used = 0.
  441. [ 3.693754] =========script_get_err============
  442. [ 3.703874] ltr_init: ls_fetch_sysconfig_para err.
  443. [ 3.714799] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0
  444. [ 3.727345] i2c /dev entries driver
  445. [ 3.736660] IR RC5(x) protocol handler initialized
  446. [ 3.747181] sunxi tsc version 0.1
  447. [ 3.756106] tscdev_init: tsc driver is disabled
  448. [ 3.766333] sunxi cedar version 0.1
  449. [ 3.775457] [cedar]: install start!!!
  450. [ 3.784746] [cedar]: install end!!!
  451. [ 3.793625] sunxi_wdt_init_module: sunxi WatchDog Timer Driver v1.0
  452. [ 3.805763] sunxi_wdt_probe: devm_ioremap return wdt_reg 0xf1c20ca0, res->start 0x01c20ca0, res->end 0x01c20cbf
  453. [ 3.817112] sunxi_wdt_probe: initialized (g_timeout=16s, g_nowayout=0)
  454. [ 3.834804] wdt_enable, write reg 0xf1c20cb8 val 0x00000000
  455. [ 3.846255] timeout_to_interv, line 167
  456. [ 3.855730] interv_to_timeout, line 189
  457. [ 3.865122] wdt_set_tmout, write 0x000000b0 to mode reg 0xf1c20cb8, actual timeout 16 sec
  458. [ 3.879810] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
  459. [ 3.894561] Bluetooth: HCI UART driver ver 2.2
  460. [ 3.904847] [cpu_freq] ERR:get cpu extremity frequency from sysconfig failed, use max_freq
  461. [ 3.919770] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.109 2014-12-4 20:51) Compiled in Oct 12 2015 at 12:00:18
  462. [ 3.936762] [mmc]: get mmc0's sdc_power is null!
  463. [ 3.947434] [mmc]: get mmc1's sdc_power is null!
  464. [ 3.958051] [mmc]: get mmc1's 2xmode ok, val = 1
  465. [ 3.968593] [mmc]: get mmc1's ddrmode ok, val = 1
  466. [ 3.979237] [mmc]: MMC host used card: 0x3, boot card: 0x0, io_card 2
  467. [ 3.992741] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  468. [ 4.011312] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  469. [ 4.029337] sunxi_leds_fetch_sysconfig_para script_parser_fetch "leds_para" leds_used = -1063626804
  470. [ 4.044918] =========script_get_err============
  471. [ 4.056890] usbcore: registered new interface driver usbhid
  472. [ 4.068658] usbhid: USB HID core driver
  473. [ 4.082248] asoc: sndcodec <-> sunxi-codec mapping ok
  474. [ 4.096468] asoc: sndhdmi <-> sunxi-hdmiaudio.0 mapping ok
  475. [ 4.108903] oprofile: using arm/armv7-ca7
  476. [ 4.119047] u32 classifier
  477. [ 4.127566] Actions configured
  478. [ 4.136791] Netfilter messages via NETLINK v0.30.
  479. [ 4.147525] nf_conntrack version 0.5.0 (15950 buckets, 63800 max)
  480. [ 4.160200] ctnetlink v0.93: registering with nfnetlink.
  481. [ 4.171693] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
  482. [ 4.185085] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
  483. [ 4.197577] xt_time: kernel timezone is -0000
  484. [ 4.208328] IPv4 over IPv4 tunneling driver
  485. [ 4.219161] gre: GRE over IPv4 demultiplexor driver
  486. [ 4.230440] ip_gre: GRE over IPv4 tunneling driver
  487. [ 4.242258] ip_tables: (C) 2000-2006 Netfilter Core Team
  488. [ 4.254312] arp_tables: (C) 2002 David S. Miller
  489. [ 4.265503] TCP: cubic registered
  490. [ 4.275206] Initializing XFRM netlink socket
  491. [ 4.286234] NET: Registered protocol family 10
  492. [ 4.298370] Mobile IPv6
  493. [ 4.307288] ip6_tables: (C) 2000-2006 Netfilter Core Team
  494. [ 4.319649] IPv6 over IPv4 tunneling driver
  495. [ 4.331503] NET: Registered protocol family 17
  496. [ 4.342657] NET: Registered protocol family 15
  497. [ 4.353811] Bluetooth: RFCOMM TTY layer initialized
  498. [ 4.365306] Bluetooth: RFCOMM socket layer initialized
  499. [ 4.377035] Bluetooth: RFCOMM ver 1.11
  500. [ 4.387172] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  501. [ 4.399116] Bluetooth: BNEP filters: protocol multicast
  502. [ 4.411005] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  503. [ 4.423803] L2TP core driver, V2.0
  504. [ 4.433676] PPPoL2TP kernel driver, V2.0
  505. [ 4.444083] L2TP IP encapsulation support (L2TPv3)
  506. [ 4.455524] L2TP netlink interface
  507. [ 4.465343] L2TP ethernet pseudowire support (L2TPv3)
  508. [ 4.476971] Registering the dns_resolver key type
  509. [ 4.488398] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
  510. [ 4.503034] ThumbEE CPU extension supported.
  511. [ 4.513829] Registering SWP/SWPB emulation handler
  512. [ 4.526043] cmdline,disp=
  513. [ 4.535017] [HDMI] power vcc-hdmi-18
  514. [ 4.575805] sunxi-rtc sunxi-rtc: setting system clock to 1970-01-01 01:02:55 UTC (3775)
  515. [ 4.590888] ths_fetch_sysconfig_para: type err device_used = 1.
  516. [ 4.605134] CPU Budget:Register notifier
  517. [ 4.615758] CPU Budget:register Success
  518. [ 4.626196] sunxi-budget-cooling sunxi-budget-cooling: Cooling device registered: thermal-budget-0
  519. [ 4.645118] [rf_pm]: select module num is 7
  520. [ 4.656005] [rf_pm]: module power0 name vcc-wifi-33
  521. [ 4.667551] [rf_pm]: failed to fetch module_power1
  522. [ 4.678977] [rf_pm]: mod has no chip_en gpio
  523. [ 4.689816] [rf_pm]: failed to fetch lpo_use_apclk
  524. [ 4.701218] [rf_pm]: regulator on.
  525. [ 4.710964] [wifi_pm]: no wifi used in configuration
  526. [ 4.722392] ALSA device list:
  527. [ 4.731473] #0: audiocodec
  528. [ 4.740320] #1: sndhdmi
  529. [ 4.748779] Warning: unable to open an initial console.
  530. [ 4.765363] Freeing init memory: 6140K
  531. [ 4.995054] [mmc]: mmc 0 detect change, present 1
  532. [ 5.180100] [DISP] disp_device_attached_and_enable,line:159:attched ok, mgr0<-->device0, type=4, mode=10
  533. [ 5.510126] [mmc]: sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  534. [ 5.536196] [mmc]: sdc0 power_supply is null
  535. [ 5.570118] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  536. [ 5.617372] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
  537. [ 5.633374] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
  538. [ 5.643350] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  539. [ 5.668160] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  540. [ 5.686736] *******************Try sdio*******************
  541. [ 5.700623] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
  542. [ 5.716544] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
  543. [ 5.732399] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
  544. [ 5.748196] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
  545. [ 5.758174] *******************Try sd *******************
  546. [ 5.776605] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  547. [ 5.793891] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  548. [ 5.813456] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  549. [ 5.891569] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  550. [ 5.912771] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
  551. [ 5.929295] [mmc]: sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
  552. [ 5.945814] [mmc]: sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B
  553. [ 5.962189] mmc0: new high speed SDHC card at address e624
  554. [ 5.974302] mmcblk0: mmc0:e624 SU08G 7.40 GiB
  555. [ 5.986112] mmcblk0: p1 p2
  556. [ 5.995494] *******************sd init ok*******************
  557. [ 11.158252] systemd-udevd[111]: starting version 215
  558. [ 12.551771] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
  559. [ 13.249362] systemd[1]: Failed to insert module 'autofs4'
  560. [ 13.500178] systemd[1]: systemd 219 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT -GNUTLS )
  561. [ 13.526776] systemd[1]: Detected architecture arm.
  562. [ 13.564603] systemd[1]: Set hostname to <OrangePI>.
  563. [ 13.851711] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
  564. [ 13.866637] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
  565. [ 13.881681] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
  566. [ 13.906003] systemd[1]: Created slice Root Slice.
  567. [ 13.917780] systemd[1]: Starting Root Slice.
  568. [ 13.936219] systemd[1]: Listening on Delayed Shutdown Socket.
  569. [ 13.949261] systemd[1]: Starting Delayed Shutdown Socket.
  570. [ 13.968966] systemd[1]: Listening on Journal Socket (/dev/log).
  571. [ 13.982091] systemd[1]: Starting Journal Socket (/dev/log).
  572. [ 14.002271] systemd[1]: Listening on Journal Audit Socket.
  573. [ 14.015047] systemd[1]: Starting Journal Audit Socket.
  574. [ 14.034653] systemd[1]: Listening on Journal Socket.
  575. [ 14.046698] systemd[1]: Starting Journal Socket.
  576. [ 14.065451] systemd[1]: Listening on udev Control Socket.
  577. [ 14.077866] systemd[1]: Starting udev Control Socket.
  578. [ 14.096986] systemd[1]: Created slice User and Session Slice.
  579. [ 14.109928] systemd[1]: Starting User and Session Slice.
  580. [ 14.129528] systemd[1]: Created slice System Slice.
  581. [ 14.141529] systemd[1]: Starting System Slice.
  582. [ 14.153019] systemd[1]: Mounted POSIX Message Queue File System.
  583. [ 14.220280] systemd[1]: Mounting Debug File System...
  584. [ 14.350591] systemd[1]: Starting Create list of required static device nodes for the current kernel...
  585. [ 14.385636] systemd[1]: Reached target Slices.
  586. [ 14.398581] systemd[1]: Starting Slices.
  587. [ 14.412460] systemd[1]: Started Set Up Additional Binary Formats.
  588. [ 14.500577] systemd[1]: Starting Setup Virtual Console...
  589. [ 14.531898] systemd[1]: Created slice system-getty.slice.
  590. [ 14.545820] systemd[1]: Starting system-getty.slice.
  591. [ 14.700591] systemd[1]: Starting Journal Service...
  592. [ 14.790684] systemd[1]: Starting Load Kernel Modules...
  593. [ 14.824625] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
  594. [ 14.840535] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
  595. [ 14.864883] systemd[1]: Reached target Swap.
  596. [ 14.877755] systemd[1]: Starting Swap.
  597. [ 14.899032] systemd[1]: Listening on fsck to fsckd communication Socket.
  598. [ 14.919918] systemd[1]: Starting fsck to fsckd communication Socket.
  599. [ 14.942898] systemd[1]: Listening on udev Kernel Socket.
  600. [ 14.955870] systemd[1]: Starting udev Kernel Socket.
  601. [ 15.050515] systemd[1]: Starting File System Check on Root Device...
  602. [ 15.080481] systemd[1]: Reached target Encrypted Volumes.
  603. [ 15.093393] systemd[1]: Starting Encrypted Volumes.
  604. [ 15.112792] systemd[1]: Reached target Remote File Systems (Pre).
  605. [ 15.126264] systemd[1]: Starting Remote File Systems (Pre).
  606. [ 15.240640] systemd[1]: Starting udev Coldplug all Devices...
  607. [ 15.268965] systemd[1]: Created slice system-serial\x2dgetty.slice.
  608. [ 15.282661] systemd[1]: Starting system-serial\x2dgetty.slice.
  609. [ 15.295995] systemd[1]: Mounted Huge Pages File System.
  610. [ 15.360386] systemd[1]: Starting LSB: Set keymap...
  611. [ 15.388697] systemd[1]: Mounted Debug File System.
  612. [ 15.408045] systemd[1]: Started Journal Service.
  613. [ 16.106936] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
RAW Paste Data