Camera WNIRDH-HO110AS 1.0 mega pixels. len 3.6mm

Welcome to minicom 2.7

OPTIONS: I18n
Compiled on Feb  7 2016, 13:37:27.
Port /dev/ttyUSB0, 10:59:27

Press CTRL-A Z for help on special keys



U-Boot 2010.06 (Sep 12 2015 - 20:57:26)

Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128XX"
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0
16384 KiB hi_sfc at 0:0 is now current device

## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   Linux-3.0.8
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2471392 Bytes = 2.4 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 3.0.8 (root@wang) (gcc version 4.4.1 (Hisilicon_v100(gcc4.4-290+uclibc_0.9.32.1+eabi+linuxpthread)) ) #11 Tue Oct 21 11:49:32 CST 2014
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: hi3518
Memory policy: ECC disabled, Data cache writeback
AXI bus clock 200000000.
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 10922
Kernel command line: mem=43M console=ttyAMA0,115200 root=/dev/mtdblock1 rootfstype=jffs2 mtdparts=hi_sfc:3M(boot),13M(rootfs)
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 43MB = 43MB total
Memory: 38940k/38940k available, 5092k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
    vmalloc : 0xc3000000 - 0xfe000000   ( 944 MB)
    lowmem  : 0xc0000000 - 0xc2b00000   (  43 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc0023000   ( 108 kB)
      .text : 0xc0023000 - 0xc0459000   (4312 kB)
      .data : 0xc045a000 - 0xc04780e0   ( 121 kB)
       .bss : 0xc0478104 - 0xc048ad30   (  76 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:32 nr_irqs:32 32
sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 42949ms
Console: colour dummy device 80x30
Calibrating delay loop... 218.72 BogoMIPS (lpj=1093632)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 5) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 5) is a PL011 rev2
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource timer1
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
fuse init (API version 7.16)
msgmni has been set to 76
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
brd: module loaded
loop: module loaded
Spi id table Version 1.22
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
SPI FLASH start_up_mode is 3 Bytes
Spi(cs1):
Block:64KB
Chip:16MB
Name:"MX25L128XX"
spi size: 16MB
chip num: 1
2 cmdlinepart partitions found on MTD device hi_sfc
Creating 2 MTD partitions on "hi_sfc":
0x000000000000-0x000000300000 : "boot"
0x000000300000-0x000001000000 : "rootfs"
Fixed MDIO Bus: probed
himii: probed
usbcore: registered new interface driver rt2500usb
usbcore: registered new interface driver rt73usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
hiusb-ehci hiusb-ehci.0: HIUSB EHCI
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
hiusb-ehci hiusb-ehci.0: irq 15, io mem 0x100b0000
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
hiusb-ohci hiusb-ohci.0: HIUSB OHCI
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
hiusb-ohci hiusb-ohci.0: irq 16, io mem 0x100a0000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
mousedev: PS/2 mouse device common for all mice
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key type
registered taskstats version 1
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
�VFS: Mounted root (jffs2 filesystem) on device 31:1.
Freeing init memory: 108K
[RCS]: /etc/init.d/S00devs
[RCS]: /etc/init.d/S01udev
udevd (440): /proc/440/oom_adj is deprecated, please use /proc/440/oom_score_adj instead.
[RCS]: /etc/init.d/S80network
/etc/init.d/rcS: line 21: ./usr/upgrade: not found
start ------------ Ver(2013.03.16)
chmod: /usr/fx256-bak.tar: No such file or directory
chmod: /usr/fx256-bak.tar: No such file or directory
tar: can't open '/usr/fx256-bak.tar': No such file or directory
ls: /tmp/fx256: No such file or directory
get /tmp/fx256 size fail !
/bin/sh: /usr/hhRestLog: not found
/bin/sh: /usr/hhRestLog: not found
cann't find bak file(/usr/fx256-bak)
count == 3(/usr/fx256)
main -- start1!
Read DeviceCfg  = [0x000080D4]
memsize 262144 logMode 0 logPri 3 FileNum 5
umount: can't umount /syslog/: Invalid argument
ln: /web/en/log0.asp: File exists
ln: /web/en/log1.asp: File exists
ln: /web/en/log2.asp: File exists
ln: /web/en/log3.asp: File exists
ln: /web/en/log4.asp: File exists
software 3.6.59.4  compile time is Nov  9 2016 13:49:27
SS_FLASH_ReadDeviceCfgUboot success 1256
cputype=3516c
byCPUTYPE=4
dwDeviceType=1
bySensorType1=0x48
st_size=80360
sttmpelen=95544
return
sysconfiglen=80360
sysconfigExtlen=43944
SS_FLASH_CheckArisVaule nARISMaxVaule 0, nARISHoldVaule 0
.inita.size Width=1280
.inita.size Height=720
*****************copy read time
************func = SS_FLASH_ReadBakTime, 17:2:17  hour = 16, pTime->minute = 32
rm: can't remove '/etc/passwd-ok': No such file or directory
Hisilicon Media Memory Zone Manager
hi3518_base: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Hisilicon UMAP device driver interface: v3.00
pa:82b00000, va:c3200000
load sys.ko ...OK!
load viu.ko ...OK!
ISP Mod init!
load vpss.ko ....OK!
load vou.ko ....OK!
load venc.ko ...OK!
load group.ko ...OK!
load chnl.ko ...OK!
load h264e.ko ...OK!
load jpege.ko ...OK!
load rc.ko ...OK!
load region.ko ....OK!
load vda.ko ....OK!
hi_i2c init is ok!
rmmod: chdir(/lib/modules): No such file or directory
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20030030: 0x00000000 --> 0x00000001
[END]
Kernel: ssp initial ok!
insmod /komod/extdrv/ssp_ad9020.ko
hi3518_io driver init start
alarmOutType gpio init 0, GpioFunctionType = 0, nav7180 = 0
hi3518_io driver init successful(2012.12.22)!
Hisilicon Watchdog Timer: 0.01 initialized. default_margin=60 sec (nowayout= 0, nodeamon= 0)
acodec inited!
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110150: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110154: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110158: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011015C: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110160: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110164: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110168: 0x00000004 --> 0x00010206
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011016C: 0x00000004 --> 0x00010206
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110170: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110174: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110178: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011017C: 0x00000004 --> 0x00003FF3
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110180: 0x00000004 --> 0x00003FF4
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110184: 0x00000004 --> 0x00010C82
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110188: 0x00000004 --> 0x00010101
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011018c: 0x00000004 --> 0x00010100
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110100: 0x0000000F --> 0x00000067
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20050038: 0x00000000 --> 0x00000003
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20580010: 0x00000000 --> 0x00000003
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x205cce00: 0x00000000 --> 0x08003003
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20600314: 0x00FFFF66 --> 0x01640000
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2061002c: 0x00888010 --> 0x00444010
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x206200A4: 0x00000007 --> 0x00000003
[END]
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x206600A4: 0x00000000 --> 0x00000003
[END]
route: SIOCADDRT: File exists
supportHH = 1
SS_PUB_Get_PassFlag CMOS_720P_OV9712 pass encrypt
net lib Make On Oct 14 2016 14:59:42
g_server_info.hMultiListenSock=0
baseip=192.168.1.120
wifiip=192.168.1.160
PHY: himii:01 - Link is Up - 100/Full
SS_PUB_Get_PassFlag CMOS_720P_OV9712 pass encrypt
*******************fx256 init
Creat queue id:0
queue id:0
mkdir: can't create directory '/onvif': File exists
device_service start...
device_service end...
3702 discovery Make On Apr 10 2015 14:32:35
send 3702  hello msg start...
...onvif search start
onvif main -- start!
[OnvifSyslog.c 58] not exits log file
.3702.hello...usDataLen=1470......
.3702.hello...ret=1470......
send 3702  hello msg end...
***stSysStatus.stDeviceCfg.byWDR:0 SysConfig.stVideoInCfg[0].struViScene.byWDR:0
ln: /fx/web/en/onvifdebug.asp: No such file or directory
LIBSENSOR  Sensor TYPE is  SENSOR_CMOS_720P_OV9732
SensorLib Make On Oct 14 2016 15:28:28
~~~~~OV9732 sensor 720P30fps init success!
umount: can't umount /onvifSyslog/: Invalid argument
ln: /fx/web/en/onviflog0.asp: No such file or directory
init sensor ov9732
...size Width=1280
...size Height=720
AnvLib Make On Oct 14 2016 15:26:31
start-------------------
~~~~~OV9732 sensor 720P30fps init success!
.....SS_Hi35xx_ViStartIsp..........VI_SENSOR_CMOS_720P_OV9732..........
111
pstChnAttr->stCapRect.u32Height:720 pstChnAttr->stDestSize.u32Height:720
Gamma Curve=1

3518 auto iris = 0
LIBANV  mm = 0 (0)mask handle = 16777215 16777215 16777215 16777215
******************mac
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20050078: 0x1E1EC001 --> 0x0909C001
[END]
gain_mic = 31
LIBANV  #########Ai Enalble Dev 0 Chn 0 Ok.
LIBANV  #########Ai Enalble Dev 0 Chn 1 Ok.
=========RTSPlib version is Apr 15 2015 17:46:02
RTSPLib Make On Apr 15 2015 17:46:02
startRtspServer rtspPort=554,bUserAuth=0,bPassive=1,mtu=1460,maxChn=1
startRtspServer begin line = 4663
********* CreatRtspServer begin  socket=0 port=554
********* CreatRtspServer result  socket=39 port=554
********* CreatRtspServer success  socket=39 port=554
setAvInfor begin line = 4620
 RTSP setAvInfor === nCh=0,bMain=0,videoPt=96,audioPt=97
setAvInfor line = 4632
setAvInfor end line = 4640
setAvInfor begin line = 4620
 RTSP setAvInfor === nCh=0,bMain=1,videoPt=96,audioPt=97
setAvInfor line = 4632
setAvInfor end line = 4640
rtsp_unicast_multicast nRtspSever=0,bMutlicast=1,szMulticastIP=239.0.0.0,nMainVideoPort=5010,nMainAudioPort=5012,nViceVideoPort=5020,nViceAudioPort=50
rtsp_unicast_multicast begin line = 4780
rtsp_unicast_multicast end line = 4799
fx256 uses obsolete (PF_INET,SOCK_PACKET)
#########@@@@@@@@@@@@@stH264Vbr.fr32TargetFrmRate:22
**********u32QpDelta = 2
enSuperFrmMode = 0, u32MaxIprop = 20
#########@@@@@@@@@@@@@stH264Vbr.fr32TargetFrmRate:22
LIBANV  ######### SS_Hi3518_VencSetChnAttr HI_MPI_VENC_SetChnAttr ok 0x0
#########@@@@@@@@@@@@@stH264Vbr.fr32TargetFrmRate:22
**********u32QpDelta = 2
enSuperFrmMode = 0, u32MaxIprop = 20
#########@@@@@@@@@@@@@stH264Vbr.fr32TargetFrmRate:22
LIBANV  ######### SS_Hi3518_VencSetChnAttr HI_MPI_VENC_SetChnAttr ok 0x0
LIBANV  ######### SS_Hi3518_VencSetChnAttr HI_MPI_VENC_SetChnAttr ok 0x0








smtpclient ----------- v1.2(2011-12-31)
smtpclient key = -1 1644232837 id = 131076 163845(/unix/smtpclient)

mkdir: can't create directory '/mempic': File exists
***********set daydefultparam
set_filter_ctrl2 == 1
set_filter_ctrl1 == 0
mkdir: can't create directory '/memrec': File exists
set_filter_ctrl2 == 0
set_filter_ctrl1 == 0
 set_infrared_lamp == 0
set_filter_ctrl2 == 0
set_filter_ctrl1 == 1
set_filter_ctrl2 == 0
set_filter_ctrl1 == 0
 set_infrared_lamp == 1
hirtc_set_time->396:
check state error!

--------sysnRtspHBTime()----------
******year = 10
******year = 10
******year = 10
******year = 10
******************mac
*** Board tools : ver0.0.1_20120501  ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20050078: 0x0E0EC001 --> 0x0909C001
[END]
gain_mic = 31
Hik_main  HD-IPCAMERA0120121218BBRR337712166
[IPC][src/md_main.c:00001438:md_main] Initialize Begin
gfxGetParameter ------------->dwCommand = 0x201
md_get_devicecfg
[IPC][src/md_main.c:00001440:md_main] Initialize
[IPC][src/md_main.c:00001441:md_main] Initialize End
SysConfig.stNetBaseWifi.byDanaArLinkFlag 0
SO_BINDTODEVICE[eth0:2] error
wait
****** ( SS_DoArLinkProcess ) byDanaArLinkFlag = 0


testdanavideo USING LIBDANAVIDEO_VERSIONset_filter_ctrl2 == 1
 1.0.150612
set_filter_ctrl1 == 0
set_filter_ctrl2 == 0
set_filter_ctrl1 == 0
 set_infrared_lamp == 0
read-----------
set_filter_ctrl2 == 0
set_filter_ctrl1 == 1
set_filter_ctrl2 == 0
set_filter_ctrl1 == 0
 set_infrared_lamp == 1
.InfraredDetectMode..cai zhuan hei .
struViScene.byphotoresistorLevel = 0
route: SIOCDELRT: No such device
route: SIOCDELRT: No such device
lib_danavideo_init succeeded
lib_danavideo_deviceid: 9ff4f9710f7bc809fcd7c189bb12028a
lib_danavideo_linked_version_str  1.0.150612
dana_arlink_start----------
AUTOSET
        power_freq: 0
        now_time: 1488859283
        time_zone: (null)
        ntp_server1: GMT+07:00
        ntp_server2: 0.asia.pool.ntp.org
testdanavideo lib_danavideo_start succeeded
THE CONN TO P2P SERVER IS OK
dana_arlink_start----------
dana_arlink_start----------
dana_arlink_start----------