API tools faq
paste
Advertisement
Cinpro

Tevo Little MOnster

Cinpro
Jun 23rd, 2017
396
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 29.57 KB | None | 0 0
raw download clone embed print report
  1. # NOTE Lines must not exceed 132 characters
  2. # Robot module configurations : general handling of movement G-codes and slicing into moves
  3. default_feed_rate 4000 # Default rate ( mm/minute ) for G1/G2/G3 moves
  4. default_seek_rate 4000 # Default rate ( mm/minute ) for G0 moves
  5. mm_per_arc_segment 0.0 # Fixed length for line segments that divide arcs 0 to disable
  6. mm_max_arc_error 0.01 # The maximum error for line segments that divide arcs 0 to disable
  7. # note it is invalid for both the above be 0
  8. # if both are used, will use largest segment length based on radius
  9. #mm_per_line_segment 0.5 # Lines can be cut into segments ( not useful with cartesian
  10. # coordinates robots ).
  11. delta_segments_per_second 100 # for deltas only same as in Marlin/Delta, set to 0 to disable
  12. # and use mm_per_line_segment
  13.  
  14.  
  15. # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
  16. arm_solution linear_delta # selects the delta arm solution
  17. alpha_steps_per_mm 160 # Steps per mm for alpha stepper
  18. beta_steps_per_mm 160 # Steps per mm for beta stepper
  19. gamma_steps_per_mm 160 # Steps per mm for gamma stepper
  20.  
  21. arm_length 397.1073 # this is the length of an arm from hinge to hinge
  22. arm_radius 149.7757 # this is the horizontal distance from hinge to hinge
  23. # when the effector is centered
  24.  
  25. # Planner module configuration : Look-ahead and acceleration configuration
  26. planner_queue_size 32 # DO NOT CHANGE THIS UNLESS YOU KNOW EXACTLY WHAT YOU ARE DOING
  27. acceleration 6000 # Acceleration in mm/second/second.
  28. junction_deviation 0.05 # Similar to the old "max_jerk", in millimeters,
  29. # see https://github.com/grbl/grbl/blob/master/planner.c#L409
  30. # and https://github.com/grbl/grbl/wiki/Configuring-Grbl-v0.8
  31. # Lower values mean being more careful, higher values means being
  32. # faster and have more jerk
  33. #minimum_planner_speed 0.0 # sets the minimum planner speed in mm/sec
  34.  
  35. # Stepper module configuration
  36. microseconds_per_step_pulse 1 # Duration of step pulses to stepper drivers, in microseconds
  37. base_stepping_frequency 100000 # Base frequency for stepping
  38.  
  39. # Cartesian axis speed limits
  40. x_axis_max_speed 40000 # mm/min
  41. y_axis_max_speed 40000 # mm/min
  42. z_axis_max_speed 40000 # mm/min
  43.  
  44. # Stepper module pins ( ports, and pin numbers, appending "!" to the number will invert a pin )
  45. alpha_step_pin 2.0 # Pin for alpha stepper step signal
  46. alpha_dir_pin 0.5 # Pin for alpha stepper direction
  47. alpha_en_pin 0.4 # Pin for alpha enable pin
  48. alpha_current 1.8 # X stepper motor current
  49. alpha_max_rate 40000.0 # mm/min
  50.  
  51. beta_step_pin 2.1 # Pin for beta stepper step signal
  52. beta_dir_pin 0.11 # Pin for beta stepper direction
  53. beta_en_pin 0.10 # Pin for beta enable
  54. beta_current 1.8 # Y stepper motor current
  55. beta_max_rate 40000.0 # mm/min
  56.  
  57. gamma_step_pin 2.2 # Pin for gamma stepper step signal
  58. gamma_dir_pin 0.20 # Pin for gamma stepper direction
  59. gamma_en_pin 0.19 # Pin for gamma enable
  60. gamma_current 1.8 # Z stepper motor current
  61. gamma_max_rate 40000.0 # mm/min
  62.  
  63. # Serial communications configuration ( baud rate default to 9600 if undefined )
  64. uart0.baud_rate 115200 # Baud rate for the default hardware serial port
  65. second_usb_serial_enable false # This enables a second usb serial port (to have both pronterface
  66. # and a terminal connected)
  67. #leds_disable true # disable using leds after config loaded
  68. #msd_disable false # disable the MSD (USB SDCARD) when set to true
  69. #dfu_enable false # for linux developers, set to true to enable DFU
  70. #watchdog_timeout 10 # watchdog timeout in seconds, default is 10, set to 0 to disable the watchdog
  71.  
  72. # Extruder module configuration
  73. extruder.hotend.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
  74. extruder.hotend.steps_per_mm 890 # Steps per mm for extruder stepper
  75. extruder.hotend.default_feed_rate 720 # Default rate ( mm/minute ) for moves where only the extruder moves
  76. extruder.hotend.acceleration 1500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
  77. extruder.hotend.max_speed 50 # mm/s
  78.  
  79. extruder.hotend.step_pin 2.3 # Pin for extruder step signal
  80. extruder.hotend.dir_pin 0.22 # Pin for extruder dir signal
  81. extruder.hotend.en_pin 0.21 # Pin for extruder enable signal
  82.  
  83. # extruder offset
  84. #extruder.hotend.x_offset 0 # x offset from origin in mm
  85. #extruder.hotend.y_offset 0 # y offset from origin in mm
  86. #extruder.hotend.z_offset 0 # z offset from origin in mm
  87.  
  88. # firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
  89. #extruder.hotend.retract_length 3 # retract length in mm
  90. #extruder.hotend.retract_feedrate 45 # retract feedrate in mm/sec
  91. #extruder.hotend.retract_recover_length 0 # additional length for recover
  92. #extruder.hotend.retract_recover_feedrate 8 # recover feedrate in mm/sec (should be less than retract feedrate)
  93. #extruder.hotend.retract_zlift_length 0 # zlift on retract in mm, 0 disables
  94. #extruder.hotend.retract_zlift_feedrate 6000 # zlift feedrate in mm/min (Note mm/min NOT mm/sec)
  95.  
  96. delta_current 1.5 # First extruder stepper motor current
  97.  
  98. # Second extruder module configuration example
  99. #extruder.hotend2.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
  100. #extruder.hotend2.steps_per_mm 140 # Steps per mm for extruder stepper
  101. #extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  102. #extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
  103. #extruder.hotend2.max_speed 50 # mm/s
  104.  
  105. #extruder.hotend2.step_pin 2.8 # Pin for extruder step signal
  106. #extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal
  107. #extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal
  108.  
  109. #extruder.hotend2.x_offset 0 # x offset from origin in mm
  110. #extruder.hotend2.y_offset 25.0 # y offset from origin in mm
  111. #extruder.hotend2.z_offset 0 # z offset from origin in mm
  112. #epsilon_current 1.5 # Second extruder stepper motor current
  113.  
  114. # Laser module configuration
  115. laser_module_enable false # Whether to activate the laser module at all. All configuration is
  116. # ignored if false.
  117. #laser_module_pin 2.5 # this pin will be PWMed to control the laser. Only P2.0 - P2.5, P1.18, P1.20, P1.21, P1.23, P1.24, P1.26, P3.25, P3.26
  118. # can be used since laser requires hardware PWM
  119. #laser_module_maximum_power 1.0 # this is the maximum duty cycle that will be applied to the laser
  120. #laser_module_minimum_power 0.0 # This is a value just below the minimum duty cycle that keeps the laser
  121. # active without actually burning.
  122. #laser_module_default_power 0.8 # This is the default laser power that will be used for cuts if a power has not been specified. The value is a scale between
  123. # the maximum and minimum power levels specified above
  124. #laser_module_pwm_period 20 # this sets the pwm frequency as the period in microseconds
  125.  
  126. # Hotend temperature control configuration
  127. temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all.
  128. # All configuration is ignored if false.
  129. temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read
  130. temperature_control.hotend.heater_pin 2.7 # Pin that controls the heater
  131. temperature_control.hotend.thermistor EPCOS100K # see http://smoothieware.org/temperaturecontrol#toc5
  132. #temperature_control.hotend.beta 4066 # or set the beta value
  133.  
  134. temperature_control.hotend.set_m_code 104 #
  135. temperature_control.hotend.set_and_wait_m_code 109 #
  136. temperature_control.hotend.designator T #
  137. temperature_control.hotend.max_temp 300 # Set maximum temperature - Will prevent heating above 300 by default
  138. temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below 0 by default
  139.  
  140. # safety control is enabled by default and can be overidden here, the values show the defaults
  141. #temperature_control.hotend.runaway_heating_timeout 900 # max is 2040 seconds, how long it can take to heat up
  142. #temperature_control.hotend.runaway_cooling_timeout 900 # max is 2040 seconds, how long it can take to cool down if temp is set lower
  143. #temperature_control.hotend.runaway_range 20 # Max setting is 63°C
  144.  
  145. temperature_control.hotend.p_factor 53.1 # permanently set the PID values after an auto pid
  146. temperature_control.hotend.i_factor 4.459 #
  147. temperature_control.hotend.d_factor 158 #
  148.  
  149. #temperature_control.hotend.max_pwm 64 # max pwm, 64 is a good value if driving a 12v resistor with 24v.
  150.  
  151. # Hotend2 temperature control configuration
  152. #temperature_control.hotend2.enable true # Whether to activate this ( "hotend" ) module at all.
  153. # All configuration is ignored if false.
  154.  
  155. #temperature_control.hotend2.thermistor_pin 0.25 # Pin for the thermistor to read
  156. #temperature_control.hotend2.heater_pin 1.23 # Pin that controls the heater
  157. #temperature_control.hotend2.thermistor EPCOS100K # http://smoothieware.org/temperaturecontrol#toc5
  158. ##temperature_control.hotend2.beta 4066 # or set the beta value
  159.  
  160. #temperature_control.hotend2.set_m_code 104 #
  161. #temperature_control.hotend2.set_and_wait_m_code 109 #
  162. #temperature_control.hotend2.designator T1 #
  163.  
  164. #temperature_control.hotend2.p_factor 13.7 # permanently set the PID values after an auto pid
  165. #temperature_control.hotend2.i_factor 0.097 #
  166. #temperature_control.hotend2.d_factor 24 #
  167.  
  168. #temperature_control.hotend2.max_pwm 64 # max pwm, 64 is a good value if driving a 12v resistor with 24v.
  169.  
  170. temperature_control.bed.enable true #
  171. temperature_control.bed.thermistor_pin 0.24 #
  172. temperature_control.bed.heater_pin 2.5 #
  173. temperature_control.bed.thermistor EPCOS100K # see http://smoothieware.org/temperaturecontrol#toc5
  174. #temperature_control.bed.beta 4066 # or set the beta value
  175.  
  176. temperature_control.bed.set_m_code 140 #
  177. temperature_control.bed.set_and_wait_m_code 190 #
  178. temperature_control.bed.designator B #
  179. temperature_control.bed.max_temp 150 # Set maximum temperature - Will prevent heating above 150 by default
  180. temperature_control.bed.min_temp 0 # Set minimum temperature - Will prevent heating below 0 by default
  181. temperature_control.bed.p_factor 90.3 # permanently set the PID values after an auto pid
  182. temperature_control.bed.i_factor 5.035
  183. temperature_control.bed.d_factor 404
  184. temperature_control.bed.max_pwm 255 # max pwm, 64 is a good value if driving a 12v resistor with 24v.
  185.  
  186. #temperature_control.bed.bang_bang false # set to true to use bang bang control rather than PID
  187. #temperature_control.bed.hysteresis 2.0 # set to the temperature in degrees C to use as hysteresis
  188. # when using bang bang
  189. temperature_control.bed.runaway_heating_timeout 900 # max is 2040 seconds, how long it can take to heat up
  190. temperature_control.bed.runaway_cooling_timeout 900 # max is 2040 seconds, how long it can take to cool down if temp is set lower
  191. temperature_control.bed.runaway_range 20 # Max setting is 63°C
  192.  
  193. # Switch module for fan control
  194. switch.fan.enable true #
  195. switch.fan.input_on_command M106 #
  196. switch.fan.input_off_command M107 #
  197. switch.fan.output_pin 2.4 #
  198. switch.fan.output_type pwm # pwm output settable with S parameter in the input_on_comand
  199. #switch.fan.max_pwm 255 # set max pwm for the pin default is 255
  200.  
  201. #switch.misc.enable true #
  202. #switch.misc.input_on_command M42 #
  203. #switch.misc.input_off_command M43 #
  204. #switch.misc.output_pin 2.4 #
  205. #switch.misc.output_type digital # just an on or off pin
  206.  
  207. switch.hotendfan.enable true #
  208. switch.hotendfan.input_on_command M42 #
  209. switch.hotendfan.input_off_command M43 #
  210. switch.hotendfan.output_pin 2.6 #
  211. switch.hotendfan.output_type pwm # "digital" is just an on or off pin
  212. #switch.hotendfan.max_pwm 128
  213.  
  214. # automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
  215. # useful to turn on a fan or water pump to cool the hotend
  216. temperatureswitch.hotend.enable true #
  217. temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor
  218. temperatureswitch.hotend.switch hotendfan # select which switch to use, matches the name of the defined switch
  219. temperatureswitch.hotend.threshold_temp 50.0 # temperature to turn on (if rising) or off the switch
  220. temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals
  221. temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals
  222.  
  223. # Switch module for spindle control
  224. #switch.spindle.enable false #
  225.  
  226. # Endstops
  227. endstops_enable true # the endstop module is enabled by default and can be disabled here
  228. delta_homing true # forces all three axis to home a the same time regardless of
  229. # what is specified in G28
  230. alpha_min_endstop nc #
  231. alpha_max_endstop 1.25v # add ! to invert pullup if switch is NO to ground
  232. alpha_homing_direction home_to_max # Home up
  233. alpha_max 0 #
  234. beta_min_endstop nc #
  235. beta_max_endstop 1.27v #
  236. beta_homing_direction home_to_max #
  237. beta_max 0 #
  238. gamma_min_endstop nc #
  239. gamma_max_endstop 1.29v #
  240. gamma_homing_direction home_to_max #
  241. gamma_max 500.00 #
  242.  
  243. alpha_max_travel 1000 # max travel in mm for alpha/X axis when homing
  244. beta_max_travel 1000 # max travel in mm for beta/Y axis when homing
  245. gamma_max_travel 1000 # max travel in mm for gamma/Z axis when homing
  246.  
  247. alpha_fast_homing_rate_mm_s 200 # homing feedrates in mm/second
  248. beta_fast_homing_rate_mm_s 200 #
  249. gamma_fast_homing_rate_mm_s 200 #
  250. alpha_slow_homing_rate_mm_s 20 #
  251. beta_slow_homing_rate_mm_s 20 #
  252. gamma_slow_homing_rate_mm_s 20
  253.  
  254. alpha_homing_retract_mm 5 # retract/bounce distance after homing in mm
  255. beta_homing_retract_mm 5 #
  256. gamma_homing_retract_mm 5 #
  257.  
  258. alpha_trim 0 # software trim for alpha stepper endstop (in mm)
  259. beta_trim 0 # software trim for beta stepper endstop (in mm)
  260. gamma_trim 0 # software trim for gamma stepper endstop (in mm)
  261.  
  262. # optional enable limit switches, actions will stop if any enabled limit switch is triggered (all are set for delta)
  263. #alpha_limit_enable false # set to true to enable X min and max limit switches
  264. #beta_limit_enable false # set to true to enable Y min and max limit switches
  265. #gamma_limit_enable false # set to true to enable Z min and max limit switches
  266.  
  267. #move_to_origin_after_home true # move XY to 0,0 after homing
  268. #endstop_debounce_count 100 # uncomment if you get noise on your endstops
  269.  
  270. # optional Z probe
  271. zprobe.enable true # set to true to enable a zprobe
  272. zprobe.probe_pin 1.28^ # pin probe is attached to if NC remove the !
  273. zprobe.slow_feedrate 10 # mm/sec probe feed rate
  274. #zprobe.debounce_count 100 # set if noisy
  275. zprobe.fast_feedrate 200 # move feedrate mm/sec
  276. zprobe.probe_height 10 # how much above bed to start probe
  277. #gamma_min_endstop nc # normally 1.28. Change to nc to prevent conflict,
  278.  
  279. # associated with zprobe the leveling strategy to use
  280. leveling-strategy.delta-calibration.enable true # basic delta calibration
  281. leveling-strategy.delta-calibration.radius 140 # the probe radius
  282.  
  283. leveling-strategy.delta-grid.enable true #
  284. leveling-strategy.delta-grid.radius 140 #
  285. leveling-strategy.delta-grid.size 7 # Must be odd number
  286. leveling-strategy.delta-grid.do_home true # Always true
  287. leveling-strategy.delta-grid.save true # true to save for future boot
  288. leveling-strategy.delta-grid.initial_height 10 #
  289.  
  290. # Switch module for servo control
  291. switch.servo.enable true #
  292. switch.servo.input_on_command M280 # M280 S7.5 would be midway
  293. switch.servo.input_off_command M281 # same as M280 S0 0% duty cycle, servo off
  294. switch.servo.output_pin 1.23 # must be a PWM capable pin
  295. switch.servo.output_type hwpwm # H/W pwm output settable with S parameter
  296. switch.servo.pwm_period_ms 20 # set period to 20ms (50Hz), default 50Hz
  297.  
  298. # kill button (used to be called pause) maybe assigned to a different pin, set to the onboard pin by default
  299. kill_button_enable true # set to true to enable a kill button
  300. kill_button_pin 2.12 # kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
  301.  
  302. # Panel
  303. panel.enable true # set to true to enable the panel code
  304. #panel.lcd smoothiepanel # set type of panel
  305. #panel.encoder_a_pin 3.25!^ # encoder pin
  306. #panel.encoder_b_pin 3.26!^ # encoder pin
  307.  
  308. # Example for reprap discount GLCD
  309. # on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
  310. # +5v is EXP1 pin 10, Gnd is EXP1 pin 9
  311. panel.lcd reprap_discount_glcd #
  312. panel.spi_channel 0 # spi channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
  313. panel.spi_cs_pin 0.16 # spi chip select ; GLCD EXP1 Pin 4
  314. panel.encoder_a_pin 3.25!^ # encoder pin ; GLCD EXP2 Pin 3
  315. panel.encoder_b_pin 3.26!^ # encoder pin ; GLCD EXP2 Pin 5
  316. panel.click_button_pin 1.30!^ # click button ; GLCD EXP1 Pin 2
  317. panel.buzz_pin 1.31 # pin for buzzer ; GLCD EXP1 Pin 1
  318. panel.button_pause_pin 2.11^ # kill/pause ; GLCD EXP2 Pin 8 either
  319. panel.back_button_pin 2.11!^ # back button ; GLCD EXP2 Pin 8 or
  320. panel.encoder_resolution 4
  321. panel.external_sd true # set to true if there is an extrernal sdcard on the panel
  322. panel.external_sd.spi_channel 1 # set spi channel the sdcard is on
  323. panel.external_sd.spi_cs_pin 0.28 # set spi chip select for the sdcard (or any spare pin)
  324. panel.external_sd.sdcd_pin 0.27!^ # sd detect signal (set to nc if no sdcard detect) (or any spare pin)
  325.  
  326. # pins used with other panels
  327. #panel.up_button_pin 0.1! # up button if used
  328. #panel.down_button_pin 0.0! # down button if used
  329. #panel.click_button_pin 0.18! # click button if used
  330.  
  331. panel.menu_offset 0 # some panels will need 1 here
  332.  
  333. panel.alpha_jog_feedrate 6000 # x jogging feedrate in mm/min
  334. panel.beta_jog_feedrate 6000 # y jogging feedrate in mm/min
  335. panel.gamma_jog_feedrate 200 # z jogging feedrate in mm/min
  336.  
  337. panel.hotend_temperature 210 # temp to set hotend when preheat is selected
  338. panel.bed_temperature 80 # temp to set bed when preheat is selected
  339.  
  340. # Example of a custom menu entry, which will show up in the Custom entry.
  341. # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
  342. custom_menu.coolingfan_off.enable true #
  343. custom_menu.coolingfan_off.name CoolFan_Off #
  344. custom_menu.coolingfan_off.command M43 #
  345.  
  346. custom_menu.coolingfan_on.enable true #
  347. custom_menu.coolingfan_on.name CoolFan_On #
  348. custom_menu.coolingfan_on.command M42 #
  349.  
  350. custom_menu.blower_off.enable true #
  351. custom_menu.blower_off.name Blower_Off #
  352. custom_menu.blower_off.command M107 #
  353.  
  354. custom_menu.blower_on.enable true #
  355. custom_menu.blower_on.name Blower_On #
  356. custom_menu.blower_on.command M106_S255 #
  357.  
  358. custom_menu.bl_up.enable true #
  359. custom_menu.bl_up.name BLTouch_Up #
  360. custom_menu.bl_up.command M280_PS7 #
  361.  
  362. custom_menu.bl_down.enable true #
  363. custom_menu.bl_down.name BLTouch_Down #
  364. custom_menu.bl_down.command M280_PS3 #
  365.  
  366. custom_menu.bl_reset.enable true #
  367. custom_menu.bl_reset.name BLTouch_Reset #
  368. custom_menu.bl_reset.command M280_PS10.6 #
  369.  
  370. custom_menu.bl_test.enable true #
  371. custom_menu.bl_test.name BLTouch_Test #
  372. custom_menu.bl_test.command M280_PS8.4 #
  373.  
  374. custom_menu.auto_calibrate.enable true #
  375. custom_menu.auto_calibrate.name Auto_Calibrate #
  376. custom_menu.auto_calibrate.command M280_PS3|M190_S80|G32|G31|M374|M500|M280_PS7|G28|M140_S0|M84|reset#
  377. #custom_menu.auto_calibrate.command M32_autocalibrate.gco #
  378.  
  379. custom_menu.eject_filament.enable true #
  380. custom_menu.eject_filament.name Eject_Filament #
  381. custom_menu.eject_filament.command G28|G0_F8000_Z100|M42|M109_T0_S240|G92_E0|G1_E10_F300|G1_E-650_F9000|M104_S0|M84#
  382.  
  383. custom_menu.load_filament.enable true #
  384. custom_menu.load_filament.name Load_Filament #
  385. custom_menu.load_filament.command G28|G0_F8000_Z100|M42|G92_E0|G1_E50_F300|M109_T0_S240|G1_E590_F9000|G1_E650_F300|M104_S0|M84#
  386.  
  387. custom_menu.save.enable true #
  388. custom_menu.save.name SAVE_SETTINGS #
  389. custom_menu.save.command M500|reset #
  390.  
  391. custom_menu.delete.enable true #
  392. custom_menu.delete.name DELETE_SETTINGS #
  393. custom_menu.delete.command M502|reset #
  394.  
  395. # Only needed on a smoothieboard
  396. currentcontrol_module_enable true #
  397.  
  398. return_error_on_unhandled_gcode false #
  399.  
  400. # network settings
  401. network.enable false # enable the ethernet network services
  402. network.webserver.enable true # enable the webserver
  403. network.telnet.enable true # enable the telnet server
  404. network.ip_address auto # use dhcp to get ip address
  405. # uncomment the 3 below to manually setup ip address
  406. #network.ip_address 192.168.3.222 # the IP address
  407. #network.ip_mask 255.255.255.0 # the ip mask
  408. #network.ip_gateway 192.168.3.1 # the gateway address
  409. #network.mac_override xx.xx.xx.xx.xx.xx # override the mac address, only do this if you have a conflict
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!