2019-01-17 00:27:59  ★ Mariana Lopez approaches the bike and sets it on the kickstand before walking to her

2019-01-17 00:28:27  ★ work bench and grabbing the handle of her tool box as she carries it along, walking      ((Mariana Lopez))

2019-01-17 00:28:33  ★ back near the bike.      ((Mariana Lopez))

2019-01-17 00:28:49  ★ Mariana Lopez drops the tool box down on the ground and takes a knee as she opens it and takes out

2019-01-17 00:29:25  ★ a torx screwdriver and a torx socket, fitting them together.      ((Mariana Lopez))

2019-01-17 00:30:09  ★ Mariana Lopez starts loosening the bolts that secure the plastic cover near the fuel tank to the bike.

2019-01-17 00:30:34  ★ Mariana Lopez grabs the plastic panel and carefully eases it out of place before placing it down on the

2019-01-17 00:30:36  ★ ground.      ((Mariana Lopez))

2019-01-17 00:30:55  ★ Mariana Lopez reveals the bike's ECU.

2019-01-17 00:32:08  ★ Mariana Lopez puts the torx screwdriver back in the tool box and reaches out for a T25 torx wrench, using

2019-01-17 00:32:43  ★ it to loosen that mounting bolt that secures the ECU's mounting bracket to the bike.      ((Mariana Lopez))

2019-01-17 00:33:25  ★ Mariana Lopez squeezes the two tabs on the wiring harness that is connected to the ECU in order to

2019-01-17 00:33:38  ★ release it before pulling it out to disconnect it.      ((Mariana Lopez))

2019-01-17 00:34:02  ★ Mariana Lopez squeezes the tabs of the second wire harness and plugs it off of the ECU.

2019-01-17 00:34:28  ★ Mariana Lopez removes the old ECU and places it aside to make enough clearance.

2019-01-17 00:36:07  ★ Mariana Lopez rubs her hands together as she glares around.

2019-01-17 00:37:22  ★ Mariana Lopez carefully undoes the two clips on the air filter frame and reaches out for a flathead

2019-01-17 00:37:43  ★ screwdriver, using it to carefully pry off the push clip in the middle.      ((Mariana Lopez))

2019-01-17 00:38:16  ★ Mariana Lopez removes the push clip and puts it aside for later use before gently holding the

2019-01-17 00:38:34  ★ intake tube from the inside and pulling it up vertically to remove it.      ((Mariana Lopez))

2019-01-17 00:39:26  ★ Mariana Lopez places it aside on the ground and takes a firm grip of the air filter frame, giving it a

2019-01-17 00:39:51  ★ good pull as she wiggles it out of place.      ((Mariana Lopez))

2019-01-17 00:40:26  ★ Mariana Lopez seperates the OEM filter from the filter frame and tosses the OEM filter down on the

2019-01-17 00:40:28  ★ ground.      ((Mariana Lopez))

2019-01-17 00:40:45  ★ Mariana Lopez puts the filter frame aside and heads to the trunk of her Golf, popping it open and carrying

2019-01-17 00:40:56  ★ a carton box with all the new parts of the bike.      ((Mariana Lopez))

2019-01-17 00:41:17  ★ Mariana Lopez sets it down on the ground and tears it open before starting to extract and undo the packagi

2019-01-17 00:41:23  ★ packaging of each item.      ((Mariana Lopez))

2019-01-17 00:41:46  ★ Mariana Lopez organizes the parts and accessories together before grabbing the aftermarket air

2019-01-17 00:42:10  ★ filter and sitting it in the appropriate slot of the filter frame.      ((Mariana Lopez))

2019-01-17 00:43:02  ★ Mariana Lopez ensures that the filter frame is facing the correct direction before slowly and carefully

2019-01-17 00:43:07  ★ dropping it back into place.      ((Mariana Lopez))

2019-01-17 00:43:45  ★ Mariana Lopez makes sure it's properly seated and snaps the clips back in place.

2019-01-17 00:44:21  ★ Mariana Lopez reaches out for the removed intake tube and puts it back in place as she sighs.

2019-01-17 00:45:10  ★ Mariana Lopez digs in her pocket and takes out the push pin, reinstalling it back on intake tube.

2019-01-17 00:46:12  ★ Mariana Lopez reaches out for the new ECU and properly slides it back in place before reinstalling

2019-01-17 00:46:24  ★ the two wire harnesses that would automatically snap in place.      ((Mariana Lopez))

2019-01-17 00:46:57  ★ Mariana Lopez adjusts the ECU mounting bracket so that the bolting holes are lined up, she'd then

2019-01-17 00:47:15  ★ reinstall the T25 bolt and use her Torx wrench to tighten it.      ((Mariana Lopez))

2019-01-17 00:47:43  ★ Mariana Lopez bends over and picks up the removed tank cover as she puts it back in place and

2019-01-17 00:48:05  ★ reinstalls all the T25 bolts manually.      ((Mariana Lopez))

2019-01-17 00:48:32  ★ Mariana Lopez then would use her torx wrench to completely tighten all the bolts and secure the

2019-01-17 00:48:39  ★ tank cover to the bike.      ((Mariana Lopez))

2019-01-17 01:06:41  ★ Mariana Lopez takes a knee and reaches out for her 6mm allen key, using it to loosen the front caliper

2019-01-17 01:06:43  ★ bolts.      ((Mariana Lopez))

2019-01-17 01:07:59  ★ Mariana Lopez only removes the two top caliper bolts all the way out, putting them aside from later

2019-01-17 01:08:01  ★ use.      ((Mariana Lopez))

2019-01-17 01:10:45  ★ Both front brake calipers would be loose with the top bolt completely removed and      ((Mariana Lopez))

2019-01-17 01:10:52  ★ only the bottom one supporting them.      ((Mariana Lopez))

2019-01-17 01:11:25  ★ Mariana Lopez reaches out for the two brackets that come with the strap kit, lining the mounting holes up

2019-01-17 01:11:44  ★ together and hand tightening the two bolts to fix them in place.      ((Mariana Lopez))

2019-01-17 01:13:17  ★ Mariana Lopez makes sure the calipers are lined up with the fork before taking her 6mm allen key and

2019-01-17 01:13:28  ★ tightening the calipers' bolts.      ((Mariana Lopez))

2019-01-17 01:14:33  ★ Mariana Lopez reaches out for the strap itself, attaching it to the left side mounting bracket and

2019-01-17 01:14:52  ★ tightening the bolts using the allen key.      ((Mariana Lopez))

2019-01-17 01:15:29  ★ Mariana Lopez easies it all the way around the frameneck, between the steering head bearings and

2019-01-17 01:15:39  ★ the gas tank bolts.      ((Mariana Lopez))

2019-01-17 01:15:59  ★ Mariana Lopez ensures that the lowering belt isn't twisted or caught on anything before attaching the othe

2019-01-17 01:16:15  ★ other end of the strap to the right side mounting bracket.      ((Mariana Lopez))

2019-01-17 01:16:51  ★ Mariana Lopez secures it using the bolts and the 6mm allen key as she sighs.

2019-01-17 01:18:11  ★ Mariana Lopez grabs the front brake lever and starts squeezing as she pulls on the strap in order to

2019-01-17 01:18:55  ★ compress the front suspension and get the bike's front side lower for better weight      ((Mariana Lopez))

2019-01-17 01:19:08  ★ distribution and to stop launch wheelies from occuring.      ((Mariana Lopez))

2019-01-17 01:26:57  ★ Mariana Lopez puts the torx wrench back in the tool box and takes a knee before reaching out

2019-01-17 01:27:17  ★ for a socket wrench and the appropriate size socket, fitting it on the wrench and using it      ((Mariana Lopez))

2019-01-17 01:28:06  ★ to undo the small bolt on the clamp that secure that exhaust muffler to the exhaust tube.      ((Mariana Lopez))

2019-01-17 01:28:34  ★ Mariana Lopez would then undo the bolt that secures the muffler hanger bracket to the bike, removing

2019-01-17 01:28:47  ★ it and pulling the muffler out to seperate it from the rest of the exhaust system.      ((Mariana Lopez))

2019-01-17 01:29:20  ★ Mariana Lopez puts it down on the ground and starts loosening the bolt on the mounting bracket of

2019-01-17 01:29:27  ★ the exhaust tube.      ((Mariana Lopez))

2019-01-17 01:29:55  ★ Mariana Lopez would then undo the bolt that compresses the clamp between the pipe and the exhaust

2019-01-17 01:29:59  ★ manifold.      ((Mariana Lopez))

2019-01-17 01:30:12  ★ Mariana Lopez pulls the exhaust tube out of the end of the manifold and places it aside.

2019-01-17 01:31:22  ★ Mariana Lopez uses her ratchet to completely loosen the 8 bolts securing the exhaust manifold to

2019-01-17 01:31:25  ★ the engine.      ((Mariana Lopez))

2019-01-17 01:32:10  ★ Mariana Lopez plugs off the O2 sensor from the exhaust manifold and puts it away along with the

2019-01-17 01:32:14  ★ other removed parts.      ((Mariana Lopez))

2019-01-17 01:32:51  ★ Mariana Lopez reaches out for the new Akrapovic headers and their gasket, positioning them

2019-01-17 01:33:02  ★ against the engine and lining up the mounting holes.      ((Mariana Lopez))

2019-01-17 01:33:20  ★ Mariana Lopez hand tightens all the bolts before using her ratchet to secure these bolts in a criss

2019-01-17 01:33:36  ★ cross pattern in order to evenly secure it.      ((Mariana Lopez))

2019-01-17 01:33:57  ★ Mariana Lopez places a clamp on the other end of the headers and connects the Akrapovic exhaust

2019-01-17 01:34:17  ★ tube, using the ratchet to tighten the bolt and compress the clamp so that the      ((Mariana Lopez))

2019-01-17 01:34:30  ★ exhaust tube is firmly secured to the headers.      ((Mariana Lopez))

2019-01-17 01:35:05  ★ Mariana Lopez reinstalls the O2 sensor in its appropriate slot from the exhaust pipe.

2019-01-17 01:35:35  ★ Mariana Lopez places a clamp over the end of the exhaust tube and carries the Akrapovic muffler

2019-01-17 01:36:03  ★ as she carefully connects it to the tube and secures them together using the clamp.      ((Mariana Lopez))

2019-01-17 01:36:34  ★ Mariana Lopez would then reinstall the hanger brackets, completely tightening the bolts to secure the

2019-01-17 01:36:41  ★ new exhaust system parts in place.      ((Mariana Lopez))

2019-01-17 01:37:07  ★ Mariana Lopez takes a brief look as she inspects the freshly mounted system, making sure everything

2019-01-17 01:37:09  ★ is fine.      ((Mariana Lopez))

2019-01-17 21:54:44  ★ Mariana Lopez grasps onto the arm of the hydraulic jack and slides it under the center of the bike

2019-01-17 21:55:04  ★ before carefully lining it up with the metalic frame and starting to      ((Mariana Lopez))

2019-01-17 21:55:30  ★ pump the arm in order to raise the motorcycle off of the ground.      ((Mariana Lopez))

2019-01-17 21:56:13  ★ Mariana Lopez reaches out for a hook strap and attaches it to one side of the jack before taking it

2019-01-17 21:56:53  ★ all over the motorcycle and hooking the strap to the other end of the jack, pulling on the      ((Mariana Lopez))

2019-01-17 21:57:03  ★ strap to make sure it's tight enough to keep the bike stable.      ((Mariana Lopez))

2019-01-17 21:57:27  ★ Mariana Lopez reaches out for an axle stands and lines it up under the rear wheel before adjusting the

2019-01-17 21:57:36  ★ height so that it supports the rear wheel.      ((Mariana Lopez))

2019-01-17 21:58:56  ★ Mariana Lopez opens her tool box and takes a ratchet along with a 32mm socket, she'd fit the socketo n

2019-01-17 21:59:32  ★ the ratchet before starting to loosen the nut from the rear axle.      ((Mariana Lopez))

2019-01-17 22:00:08  ★ Mariana Lopez would save the removed nut aside, the rear axle would be all loose by now.

2019-01-17 22:00:34  ★ Mariana Lopez fits a pair of latex gloves on her hands and grabs the bike's chain as she removes it from

2019-01-17 22:00:46  ★ the rear sprocket.      ((Mariana Lopez))

2019-01-17 22:01:22  ★ Mariana Lopez grasps onto the rear wheel and carefully rolls it out from the motorcycle swingarm.

2019-01-17 22:08:06  ★ Mariana Lopez uses the ratchet to undo the two bolts that secure the chain guard in place, she'd then

2019-01-17 22:08:27  ★ pull it out and place it down on the ground before fitting the appropriate size socket on      ((Mariana Lopez))

2019-01-17 22:09:08  ★ the ratchet and using it to loosen up the two bolts of the rear brake caliper.      ((Mariana Lopez))

2019-01-17 22:09:26  ★ Mariana Lopez supports the brake caliper with her left hand and puts the ratchet back in the tool box as

2019-01-17 22:09:43  ★ she takes out an 8mm open end wrench, using it to loosen the small nut that secure      ((Mariana Lopez))

2019-01-17 22:10:01  ★ secures the brake line to the caliper.      ((Mariana Lopez))

2019-01-17 22:10:18  ★ Mariana Lopez plugs off the brake line and puts the removed caliper aside before taking her ratchet

2019-01-17 22:10:51  ★ and fitting the 32mm socket, using it to loosen the swingarm pivot axle bolt.      ((Mariana Lopez))

2019-01-17 22:11:30  ★ Mariana Lopez removes the bolts and uses the tip of her ratchet to hammer the pivor axle out of place

2019-01-17 22:11:46  ★ to release the swingarm.      ((Mariana Lopez))

2019-01-17 22:12:24  ★ Mariana Lopez grabs the swingarm and pulls it off the bike before placing it down on the ground.

2019-01-17 22:13:30  ★ Mariana Lopez reaches out for the new extended swingarm, putting it in place and inserting the swingarm

2019-01-17 22:13:38  ★ pivot bolt.      ((Mariana Lopez))

2019-01-17 22:14:35  ★ Mariana Lopez tightens the pivot bolt with her ratchet and 32mm socket.

2019-01-17 22:15:27  ★ Mariana Lopez reaches out for the chain guard, putting it in place and securing it by fitting the right

2019-01-17 22:15:35  ★ size socket on her ratchet and tightening the two bolts.      ((Mariana Lopez))

2019-01-17 22:16:06  ★ Mariana Lopez would take the removed brake caliper, lining up the mounting holes on it with the

2019-01-17 22:16:22  ★ mounting holes on the caliper bracket and hand tightening the two bolts to get them      ((Mariana Lopez))

2019-01-17 22:16:24  ★ started.      ((Mariana Lopez))

2019-01-17 22:16:46  ★ Mariana Lopez uses the ratchet to tighten these two bolts and secure the rear caliper in place.

2019-01-17 22:17:29  ★ Mariana Lopez grasps onto the edging of the wheel and lifts it up as she positions it properly onto

2019-01-17 22:18:00  ★ the axle stand.      ((Mariana Lopez))

2019-01-17 22:18:57  ★ Mariana Lopez slides the chain back onto the rear sprocket and readjusts the wheel so that the rear axle

2019-01-17 22:19:03  ★ could be installed.      ((Mariana Lopez))

2019-01-17 22:19:16  ★ Mariana Lopez grabs the removed rear axle and inserts it back in place before fitting her ratchet with a

2019-01-17 22:19:32  ★ 32mm socket, tightening the axle bolt afterwards.      ((Mariana Lopez))

2019-01-17 22:19:38  Mariana Lopez: (( axle nut* ))

2019-01-17 22:20:20  ★ Mariana Lopez detaches the hook strap that's keeping the bike stable and moves the axle stand from beneath

2019-01-17 22:20:39  ★ the rear wheel before turning the jack's arm counter clockwise to slowly and safely lower      ((Mariana Lopez))

2019-01-17 22:20:44  ★ the bike back on the ground.      ((Mariana Lopez))

2019-01-17 22:26:27  ★ Mariana Lopez applies the kickstand to support the bike and reaches out for a T25 torx driver.

2019-01-17 22:27:01  ★ Mariana Lopez gently moves the cushion on the rear side of the seat, exposing two screws and loosening

2019-01-17 22:27:07  ★ them using the T25 torx driver.      ((Mariana Lopez))

2019-01-17 22:27:38  ★ Mariana Lopez saves the two screws aside and puts the torx driver back in the tool box.

2019-01-17 22:27:57  ★ Mariana Lopez takes a firm grip on the seat and pulls it out and up, disengaging the grommets and

2019-01-17 22:28:06  ★ taking it off before placing it down on the ground.      ((Mariana Lopez))

2019-01-17 22:31:21  ★ Mariana Lopez takes the T25 torx driver and uses it to undo the six screws that hold the plastic

2019-01-17 22:31:31  ★ tank cover in place, easing it off gently.      ((Mariana Lopez))

2019-01-17 22:31:45  ★ Mariana Lopez places the tank cover down on the ground and puts the torx driver back in the tool box.

2019-01-17 22:32:46  ★ Mariana Lopez grasps on the end of the first vent hose, pulling it out in a jiggling motion in order to

2019-01-17 22:32:49  ★ make it easier.      ((Mariana Lopez))

2019-01-17 22:33:11  ★ Mariana Lopez takse a grip on the second vent hose and pulls it off the fuel tank, disconnecting it.

2019-01-17 22:33:41  ★ Mariana Lopez squeezes the quick disconnect button on the fuel line and disconnects it from the

2019-01-17 22:35:01  ★ fuel tank.      ((Mariana Lopez))

2019-01-17 22:35:34  ★ Mariana Lopez squeezes the tab on the wiring harness connected to the fuel pump assembly before

2019-01-17 22:35:43  ★ pulling it out and disconnecting it.      ((Mariana Lopez))

2019-01-17 22:36:16  ★ Mariana Lopez fits an 8mm socket on the end of her ratchet and uses it to loosen the 6 bolts that

2019-01-17 22:36:28  ★ secure the fuel pump assembly.      ((Mariana Lopez))

2019-01-17 22:37:01  ★ Mariana Lopez saves the 6 bolts aside and grips the fuel pump assembly as she carefully fishes it out of

2019-01-17 22:37:04  ★ the fuel tank.      ((Mariana Lopez))

2019-01-17 22:37:33  ★ Mariana Lopez takes her philips head screwdriver and unscrew the plastic lid on top of

2019-01-17 22:37:39  ★ the fuel pump assembly.      ((Mariana Lopez))

2019-01-17 22:38:13  ★ Mariana Lopez disconnects the wire harness that goes to the fuel pump and fishes the fuel pump out

2019-01-17 22:38:17  ★ of the assembly.      ((Mariana Lopez))

2019-01-17 22:38:31  ★ Mariana Lopez places it aside and reaches out for the new fuel pump, dropping it in place and reconnecting

2019-01-17 22:38:38  ★ the wiring harness.      ((Mariana Lopez))

2019-01-17 22:38:57  ★ Mariana Lopez places the plastic lid on top of the fuel pump assembly and uses the philips head

2019-01-17 22:39:06  ★ screwdriver to secure it using the screws she removed earlier.      ((Mariana Lopez))

2019-01-17 22:39:38  ★ Mariana Lopez carefully drops the fuel pump assembly back in the fuel tank, putting her philips head

2019-01-17 22:39:51  ★ back in the tool box and taking the ratchet with the 8mm socket fitted on.      ((Mariana Lopez))

2019-01-17 22:40:11  ★ Mariana Lopez uses the ratchet to secure all the 6 bolts that secure the fuel pump assembly to the fuel

2019-01-17 22:40:13  ★ tank.      ((Mariana Lopez))

2019-01-17 22:40:38  ★ Mariana Lopez reconnects the removed wiring harness, it would automatically clip in place.

2019-01-17 22:41:28  ★ Mariana Lopez firmly reconnects the two vent hoses and ensures that they are tight enough.

2019-01-17 22:41:50  ★ Mariana Lopez grabs the end of the removed fuel line and reconnects it in the appropriate port on the fuel

2019-01-17 22:41:55  ★ pump assembly.      ((Mariana Lopez))

2019-01-17 22:42:51  ★ Mariana Lopez takes a moment to look at the motorcycle, making sure that she installed everything

2019-01-17 22:42:54  ★ correctly.      ((Mariana Lopez))

2019-01-17 22:46:19  ★ Mariana Lopez heads to her work bench and takes an empty plastic container along with a bottle of

2019-01-17 22:46:23  ★ engine oil.      ((Mariana Lopez))

2019-01-17 22:46:41  ★ Mariana Lopez twists the cap off the bottle and fills the plastic container with engine oil before putting

2019-01-17 22:46:45  ★ the bottle back in place.      ((Mariana Lopez))

2019-01-17 22:48:52  ★ Mariana Lopez reaches out for the new clutch disks as she puts them in the container and leaves them

2019-01-17 22:49:03  ★ there to soak in engine oil prior to installation.      ((Mariana Lopez))

2019-01-17 22:49:36  ★ Mariana Lopez heads back to the bike as she looks down on the ground, trying to figure out what parts left

2019-01-17 22:49:40  ★ to install.      ((Mariana Lopez))

2019-01-17 22:53:42  ★ Mariana Lopez awaits around an hour, allowing the clutch disks to completely soak in engine oil.

2019-01-17 22:54:02  ★ Mariana Lopez grabs the container and comes close to the bike, puting it down on the ground.

2019-01-17 22:54:45  ★ Mariana Lopez grabs another plastic container and places it beneath the bike's oil draining point.

2019-01-17 22:55:03  ★ Mariana Lopez reaches out for the ratchet along with the 10mm socket, fitting it on and loosening the oil

2019-01-17 22:55:22  ★ draining nut, allowing the engine oil to drain in the plastic container.      ((Mariana Lopez))

2019-01-17 22:56:12  ★ Mariana Lopez uses the ratchet and the same socket to loosen all the bolts securing the clutch cover

2019-01-17 22:56:18  ★ and taking it off as she places it aside.      ((Mariana Lopez))

2019-01-17 22:56:50  ★ Mariana Lopez removes the clutch cover gasket and puts it aside as well.

2019-01-17 22:57:26  ★ Mariana Lopez fits her ratchet with a 14mm socket and uses it to unscrew the 5 clutch spring bolts, saving

2019-01-17 22:57:29  ★ them aside.      ((Mariana Lopez))

2019-01-17 22:58:01  ★ Mariana Lopez grabs the inner clutch pressure plate and lifts it away before placing it down on the

2019-01-17 22:58:03  ★ ground.      ((Mariana Lopez))

2019-01-17 22:58:48  ★ Mariana Lopez uses her fingers to carefully remove the clutch disks one at a time, stacking them down on

2019-01-17 22:59:00  ★ the ground for later reference.      ((Mariana Lopez))

2019-01-17 23:00:30  ★ Mariana Lopez takes the new disks out of the container they are soaking in, starting to install them and

2019-01-17 23:00:45  ★ using the old ones as a reference for the right order.      ((Mariana Lopez))

2019-01-17 23:01:19  ★ Mariana Lopez grabs the removed pressure plate and makes sure the ridges on it mate with the

2019-01-17 23:01:28  ★ ridges on the inner hub as she installs it.      ((Mariana Lopez))

2019-01-17 23:01:51  ★ Mariana Lopez reinstalls the clutch springs and tightens them using the ratchet, in a criss cross pattern.

2019-01-17 23:02:08  ★ Mariana Lopez detaches the 14mm socket from the ratchet and fits it on her torque wrench from the

2019-01-17 23:02:12  ★ tool box.      ((Mariana Lopez))

2019-01-17 23:02:47  ★ Mariana Lopez uses the torque wrench to torque each of the 5 spring bolts to 10ft/pound each.

2019-01-17 23:03:05  ★ Mariana Lopez puts the torque wrench aside and takes a 10mm socket as she fits it on her ratchet.

2019-01-17 23:03:56  ★ Mariana Lopez grabs the gasket and the clutch cover, putting both of them in position and hand tightening

2019-01-17 23:04:07  ★ the bolts that secure the clutch cover in place.      ((Mariana Lopez))

2019-01-17 23:04:30  ★ Mariana Lopez tightens the clutch cover bolts with the ratchet and walks  to her workbench, taking a

2019-01-17 23:04:56  ★ engine oil bottle and heading back to the bike.      ((Mariana Lopez))

2019-01-17 23:07:10  ★ Mariana Lopez twists off the oil fill cap and starts pouring engine oil in there.

2019-01-17 23:07:37  ★ Mariana Lopez stops when a bit of oil pours out of the filling hole.

2019-01-17 23:07:58  ★ Mariana Lopez puts the engine oil bottle back on her workbench and fits the oil fill cap back in place.

2019-01-17 23:08:12  ★ Mariana Lopez uses a clean rag to wipe off the mess she made with the oil.

2019-01-17 23:08:21  ★ Mariana Lopez tosses the rag aside.

2019-01-17 23:13:35  ★ Mariana Lopez moves the oil containers aside to make enough clearance around the bike.

2019-01-17 23:13:58  ★ Mariana Lopez grabs another empty container and places it under the bike's engine as she then reaches out

2019-01-17 23:14:31  ★ for a 10mm open end wrench and using it to loosen the draining bolt on the water pump.      ((Mariana Lopez))

2019-01-17 23:14:47  ★ Water would start dripping slowly from the draining point.      ((Mariana Lopez))

2019-01-17 23:15:15  ★ Mariana Lopez reaches out for a T25 torx driver and uses it to undo the screws on the side body panels,

2019-01-17 23:15:20  ★ revealing the radiator.      ((Mariana Lopez))

2019-01-17 23:15:35  ★ Mariana Lopez twists off the radiator cap, the water would start flowing out of the draining point way

2019-01-17 23:15:41  ★ faster than before.      ((Mariana Lopez))

2019-01-17 23:16:15  ★ Mariana Lopez awaits until all the cooling water drains out of the engine, she'd reach out for her

2019-01-17 23:16:55  ★ flathead screwdriver found in her tool box, using it to unscrew the clamp on each end      ((Mariana Lopez))

2019-01-17 23:17:17  ★ of the radiator hose that connects the water pump with the radiator.      ((Mariana Lopez))

2019-01-17 23:18:23  ★ Mariana Lopez removes that hose and puts it on the ground.

2019-01-17 23:20:12  ★ Mariana Lopez reaches out for the blue aftermarket radiator hoses from the kit and searches for the

2019-01-17 23:20:31  ★ hose that looks just like the stock one she removed.      ((Mariana Lopez))

2019-01-17 23:21:03  ★ Mariana Lopez takes two clamps and slides them onto that new hose, connecting one of its ends with

2019-01-17 23:21:16  ★ the water pump and the other end to the radiator.      ((Mariana Lopez))

2019-01-17 23:23:28  ★ Mariana Lopez uses the screwdriver to loosen the clamp on each side of the upper radiator hose connected

2019-01-17 23:23:32  ★ to the engine.      ((Mariana Lopez))

2019-01-17 23:24:14  ★ Mariana Lopez disconnects that exact hose and searches for a new hose that has the same size and looks

2019-01-17 23:24:16  ★ like it.      ((Mariana Lopez))

2019-01-17 23:24:40  ★ Mariana Lopez slides two clamps on the new upper hose and connects one end to the appropriate port from

2019-01-17 23:24:54  ★ the radiator and the other one to its port on the engine head.      ((Mariana Lopez))

2019-01-17 23:25:18  ★ Mariana Lopez tightens the two clamps using her screwdriver to ensure that the hose is safely secured.

2019-01-17 23:26:09  ★ Mariana Lopez reaches out for the new sealing washer and draining bolt that came with the kit, she'd

2019-01-17 23:26:33  ★ fit them on the draining hole manually and use her 10mm ratchet to tighten the draining bolt      ((Mariana Lopez))

2019-01-17 23:26:47  ★ tight enough that it wouldn't leak any coolant in the future.      ((Mariana Lopez))

2019-01-17 23:28:35  ★ Mariana Lopez takes the performance coolant bottle that came with the kit and undoes the cap before

2019-01-17 23:29:13  ★ pouring coolant in the radiator through the filling hole.      ((Mariana Lopez))

2019-01-17 23:30:05  ★ Mariana Lopez puts the empty bottle aside and grabs the new upgraded radiator cap that has a gauge

2019-01-17 23:30:42  ★ dropping it in place and twisting it clockwise to tighten it and seal the radiator.      ((Mariana Lopez))

2019-01-17 23:31:15  ★ Mariana Lopez takes a T25 Torx driver from the tool box and fits the side body panels back in place

2019-01-17 23:31:35  ★ before using the torx driver to tighten all the T25 screws that hold the side body panels.      ((Mariana Lopez))

019-01-17 23:35:42  ★ Mariana Lopez looks at the parts left, only the spark plugs are left to be installed.

2019-01-17 23:37:29  ★ Mariana Lopez disconnects the two vent hoses connected to the fuel pump assembly manually.

2019-01-17 23:37:45  ★ Mariana Lopez squeezes the tab on the wiring connector to release it before disconnecting it as

2019-01-17 23:37:47  ★ well.      ((Mariana Lopez))

2019-01-17 23:38:22  ★ Mariana Lopez pushes the quick disconnects button on the fuel pump line to pop it off.

2019-01-17 23:39:14  ★ Mariana Lopez uses her ratchet and 10mm socket to loosen the bolt on each side of the fuel tank.

2019-01-17 23:39:40  ★ Mariana Lopez would then undo the bolt the back of the tank, proceeding to save all the removed bolts for

2019-01-17 23:39:45  ★ later use.      ((Mariana Lopez))

2019-01-17 23:40:05  ★ Mariana Lopez grasps on the fuel tank and carefully eases it off, placing it down on the ground as

2019-01-17 23:40:15  ★ careful as she can.      ((Mariana Lopez))

2019-01-17 23:42:07  ★ Mariana Lopez unclips the intake tube and pulls it out vertically, placing it aside.

2019-01-17 23:42:33  ★ Mariana Lopez takes a grip onto the air filter frame and pulls it out as she puts it down on the ground.

2019-01-17 23:45:40  ★ Mariana Lopez reveals the four ignition coil packs, she'd carefully squeeze the tab on each wiring harness

2019-01-17 23:45:53  ★ connected to each coil pack, disconnecting them.      ((Mariana Lopez))

2019-01-17 23:47:00  ★ Mariana Lopez starts manually turning the coil packs counter clockwise to pull all the packs out of

2019-01-17 23:47:02  ★ place.      ((Mariana Lopez))

2019-01-17 23:47:29  ★ Mariana Lopez manually starts removing the old spark plugs by turning them counter clockwise and pulling

2019-01-17 23:47:45  ★ them out of the ignition packs.      ((Mariana Lopez))

2019-01-17 23:48:19  ★ Mariana Lopez unpackages the new spark plugs and fits them into the ignition packs individually as she

2019-01-17 23:48:38  ★ inserts them and turns them clockwise to tighten them up.      ((Mariana Lopez))

2019-01-17 23:50:08  ★ Mariana Lopez drops each coil pack back in place and tightens them.

2019-01-17 23:50:26  ★ Mariana Lopez reconnects the wiring harnesses to the coil packs, they would all snap in place as the

2019-01-17 23:50:30  ★ clip would engage.      ((Mariana Lopez))

2019-01-17 23:51:00  ★ Mariana Lopez bends over and picks up the air filter frame, sitting it in place and attaching the two

2019-01-17 23:51:02  ★ clips.      ((Mariana Lopez))

2019-01-17 23:52:06  ★ Mariana Lopez picks up the intake tube and slides it back in place as she inserts the push clip.

2019-01-17 23:52:48  ★ Mariana Lopez grabs the fuel tank and lifts it up as she gently lies it back in place, reconnecting the tw

2019-01-17 23:52:55  ★ two vent hoses.      ((Mariana Lopez))

2019-01-17 23:53:24  ★ Mariana Lopez grabs the fuel line and plugs it back with the port as it would snap in place and lock.

2019-01-17 23:53:57  ★ Mariana Lopez reconnects the wire harness to the fuel pump assembly and takes a brief look at

2019-01-17 23:54:03  ★ the bike to make sure nothing is wrong.      ((Mariana Lopez))

2019-01-17 23:55:35  ★ Mariana Lopez uses her ratchet to tighten the the bolt on each side of the fuel tank before fastening the

2019-01-17 23:55:41  ★ last one in the back of the tank.      ((Mariana Lopez))

2019-01-17 23:55:57  ★ Mariana Lopez attempts to shake the fuel tank, it would be tight and firm.

2019-01-17 23:56:55  ★ Mariana Lopez carries the motorcycle seat and carefully lays it back in place, lining up the mounting

2019-01-17 23:56:57  ★ holes together.      ((Mariana Lopez))

2019-01-17 23:57:14  ★ Mariana Lopez grabs a T25 Torx driver and uses it to fasten the two screws in the back of the seat.

2019-01-17 23:57:44  ★ Mariana Lopez picks up the plastic tank cover, putting it in place and securing it by tightening the

2019-01-17 23:57:55  ★ T25 screws on the sides.      ((Mariana Lopez))