Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 2015.01-armada-17.02.0-g8128e91 (Jun 02 2017 - 09:41:51)
- I2C: ready
- DRAM: 1 GiB
- Board: DB-88F3720-ESPRESSOBin
- CPU @ 1000 [MHz]
- L2 @ 800 [MHz]
- TClock @ 200 [MHz]
- DDR @ 800 [MHz]
- Comphy-0: PEX0 2.5 Gbps
- Comphy-1: USB3 5 Gbps
- Comphy-2: SATA0 5 Gbps
- Now running in RAM - U-Boot at: 3ff2b000
- U-Boot DT blob at : 000000003fa18168
- MMC: XENON-SDHCI: 0
- SF: Detected W25Q32DW with page size 256 Bytes, erase size 4 KiB, total 4 MiB
- PCIE-0: Link down
- SCSI: Target spinup took 0 ms.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- Net: neta0
- Hit any key to stop autoboot: 0
- Setting SCSI to 0
- Target spinup took 0 ms.
- AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
- flags: ncq led only pmp fbss pio slum part sxs
- scanning bus 0 for devices...
- Device 0: (0:0) Vendor: ATA Prod.: OCZ-VERTEX2 Rev: 1.37
- Type: Hard Disk
- Capacity: 114473.4 MB = 111.7 GB (234441648 x 512)
- Invalid port number 2
- Invalid port number 3
- Invalid port number 4
- Invalid port number 5
- Invalid port number 6
- Invalid port number 7
- Found 1 device(s).
- SCSI device 0:
- Device 0: (0:0) Vendor: ATA Prod.: OCZ-VERTEX2 Rev: 1.37
- Type: Hard Disk
- Capacity: 114473.4 MB = 111.7 GB (234441648 x 512)
- ... is now current device
- 14604800 bytes read in 656 ms (21.2 MiB/s)
- 12901067 bytes read in 593 ms (20.7 MiB/s)
- 7361 bytes read in 43 ms (167 KiB/s)
- ## Loading init Ramdisk from Legacy Image at 01100000 ...
- Image Name: initrd.img-4.12.1-ebin-g4b13ed5-
- Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
- Data Size: 12901003 Bytes = 12.3 MiB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- ## Flattened Device Tree blob at 01000000
- Booting using the fdt blob at 0x1000000
- Loading Ramdisk to 1f3b2000, end 1ffffa8b ... OK
- Using Device Tree in place at 0000000001000000, end 0000000001004cc0
- Starting kernel ...
- Timer summary in microseconds:
- Mark Elapsed Stage
- 0 0 reset
- 524,000 524,000 id=64
- 536,000 12,000 id=65
- 537,000 1,000 main_loop
- 4,959,000 4,422,000 bootm_start
- 9,818,000 4,859,000 id=9
- 9,818,000 0 id=10
- 13,085,000 3,267,000 id=11
- 13,091,000 6,000 id=12
- 17,173,000 4,082,000 start_kernel
- 17,173,000 0 id=15
- 169,905,373,014,476,551,28169,905,373,014,304,821,28 board_init_f
- Accumulated time:
- [ 0.000000] Booting Linux on physical CPU 0x0
- [ 0.000000] Linux version 4.12.1-ebin-g4b13ed5-dirty (ubuntu@ebin) (gcc version 6.3.0 20170519 (Ubuntu/Linaro 6.3.0-18ubuntu2~16.04) ) #1 SMP PREEMPT Wed Jul 12 16:25:39 UTC 2017
- [ 0.000000] Boot CPU: AArch64 Processor [410fd034]
- [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board
- [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '')
- [ 0.000000] bootconsole [ar3700_uart0] enabled
- [ 0.000000] efi: Getting EFI parameters from FDT:
- [ 0.000000] efi: UEFI not found.
- [ 0.000000] cma: Reserved 16 MiB at 0x000000003f000000
- [ 0.000000] NUMA: No NUMA configuration found
- [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] NUMA: Adding memblock [0x0 - 0x3ffffff] on node 0
- [ 0.000000] NUMA: Adding memblock [0x41e0000 - 0x3fffffff] on node 0
- [ 0.000000] NUMA: Initmem setup node 0 [mem 0x00000000-0x3fffffff]
- [ 0.000000] NUMA: NODE_DATA [mem 0x3efe7800-0x3efe92ff]
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] Normal empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] node 0: [mem 0x00000000041e0000-0x000000003fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] psci: probing for conduit method from DT.
- [ 0.000000] psci: PSCIv1.0 detected in firmware.
- [ 0.000000] psci: Using standard PSCI v0.2 function IDs
- [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
- [ 0.000000] percpu: Embedded 24 pages/cpu @ffff80003efb4000 s60184 r8192 d29928 u98304
- [ 0.000000] Detected VIPT I-cache on CPU0
- [ 0.000000] CPU features: enabling workaround for ARM erratum 845719
- [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 257568
- [ 0.000000] Policy zone: DMA
- [ 0.000000] Kernel command line: console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000 root=/dev/sda1 rw rootwait
- [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
- [ 0.000000] Memory: 986356K/1046656K available (9596K kernel code, 694K rwdata, 3308K rodata, 640K init, 304K bss, 43916K reserved, 16384K cma-reserved)
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] modules : 0xffff000000000000 - 0xffff000008000000 ( 128 MB)
- [ 0.000000] vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000 (129022 GB)
- [ 0.000000] .text : 0xffff000008080000 - 0xffff0000089e0000 ( 9600 KB)
- [ 0.000000] .rodata : 0xffff0000089e0000 - 0xffff000008d20000 ( 3328 KB)
- [ 0.000000] .init : 0xffff000008d20000 - 0xffff000008dc0000 ( 640 KB)
- [ 0.000000] .data : 0xffff000008dc0000 - 0xffff000008e6da00 ( 695 KB)
- [ 0.000000] .bss : 0xffff000008e6da00 - 0xffff000008eb9de4 ( 305 KB)
- [ 0.000000] fixed : 0xffff7dfffe7fd000 - 0xffff7dfffec00000 ( 4108 KB)
- [ 0.000000] PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000 ( 16 MB)
- [ 0.000000] vmemmap : 0xffff7e0000000000 - 0xffff800000000000 ( 2048 GB maximum)
- [ 0.000000] 0xffff7e0000000000 - 0xffff7e0001000000 ( 16 MB actual)
- [ 0.000000] memory : 0xffff800000000000 - 0xffff800040000000 ( 1024 MB)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] Preemptible hierarchical RCU implementation.
- [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=2.
- [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
- [ 0.000000] NR_IRQS:64 nr_irqs:64 0
- [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
- [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000
- [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
- [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
- [ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
- [ 0.008412] Console: colour dummy device 80x25
- [ 0.012952] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=50000)
- [ 0.023480] pid_max: default: 32768 minimum: 301
- [ 0.028291] Security Framework initialized
- [ 0.032684] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
- [ 0.040863] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
- [ 0.048278] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
- [ 0.055107] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
- [ 0.078539] ASID allocator initialised with 65536 entries
- [ 0.092229] EFI services will not be available.
- [ 0.112853] smp: Bringing up secondary CPUs ...
- [ 0.149593] Detected VIPT I-cache on CPU1
- [ 0.149619] GICv3: CPU1: found redistributor 1 region 0:0x00000000d1d60000
- [ 0.149646] CPU1: Booted secondary processor [410fd034]
- [ 0.149711] smp: Brought up 1 node, 2 CPUs
- [ 0.170423] SMP: Total of 2 processors activated.
- [ 0.175262] CPU features: detected feature: GIC system register CPU interface
- [ 0.182609] CPU features: detected feature: 32-bit EL0 Support
- [ 0.188703] CPU: All CPU(s) started at EL2
- [ 0.192850] alternatives: patching kernel code
- [ 0.198065] devtmpfs: initialized
- [ 0.203020] DMI not present or invalid.
- [ 0.207072] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
- [ 0.217062] futex hash table entries: 512 (order: 4, 65536 bytes)
- [ 0.223842] xor: measuring software checksum speed
- [ 0.268782] 8regs : 1918.000 MB/sec
- [ 0.313048] 8regs_prefetch: 1710.000 MB/sec
- [ 0.357671] 32regs : 2273.000 MB/sec
- [ 0.401938] 32regs_prefetch: 1984.000 MB/sec
- [ 0.406610] xor: using function: 32regs (2273.000 MB/sec)
- [ 0.412171] pinctrl core: initialized pinctrl subsystem
- [ 0.418468] NET: Registered protocol family 16
- [ 0.424186] cpuidle: using governor ladder
- [ 0.428426] cpuidle: using governor menu
- [ 0.432726] vdso: 2 pages (1 code @ ffff0000089e7000, 1 data @ ffff000008dc5000)
- [ 0.440299] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
- [ 0.454559] DMA: preallocated 256 KiB pool for atomic allocations
- [ 0.460913] Serial: AMBA PL011 UART driver
- [ 0.466222] d0012000.serial: ttyMV0 at MMIO 0xd0012000 (irq = 9, base_baud = 0) is a mvebu-uart
- [ 0.475151] console [ttyMV0] enabled
- [ 0.475151] console [ttyMV0] enabled
- [ 0.482471] bootconsole [ar3700_uart0] disabled
- [ 0.482471] bootconsole [ar3700_uart0] disabled
- [ 0.512078] HugeTLB registered 2 MB page size, pre-allocated 0 pages
- [ 0.588162] raid6: int64x1 gen() 386 MB/s
- [ 0.660737] raid6: int64x1 xor() 380 MB/s
- [ 0.728852] raid6: int64x2 gen() 602 MB/s
- [ 0.801011] raid6: int64x2 xor() 509 MB/s
- [ 0.869098] raid6: int64x4 gen() 867 MB/s
- [ 0.941286] raid6: int64x4 xor() 632 MB/s
- [ 1.009338] raid6: int64x8 gen() 945 MB/s
- [ 1.077412] raid6: int64x8 xor() 616 MB/s
- [ 1.145503] raid6: neonx1 gen() 631 MB/s
- [ 1.217501] raid6: neonx1 xor() 652 MB/s
- [ 1.285551] raid6: neonx2 gen() 1041 MB/s
- [ 1.357629] raid6: neonx2 xor() 889 MB/s
- [ 1.425693] raid6: neonx4 gen() 1332 MB/s
- [ 1.493732] raid6: neonx4 xor() 1013 MB/s
- [ 1.565789] raid6: neonx8 gen() 1420 MB/s
- [ 1.637877] raid6: neonx8 xor() 1046 MB/s
- [ 1.641751] raid6: using algorithm neonx8 gen() 1420 MB/s
- [ 1.647142] raid6: .... xor() 1046 MB/s, rmw enabled
- [ 1.652706] raid6: using intx1 recovery algorithm
- [ 1.658030] ACPI: Interpreter disabled.
- [ 1.662567] vgaarb: loaded
- [ 1.665371] SCSI subsystem initialized
- [ 1.669845] usbcore: registered new interface driver usbfs
- [ 1.675531] usbcore: registered new interface driver hub
- [ 1.680931] usbcore: registered new device driver usb
- [ 1.686541] pxa2xx-i2c d0011000.i2c: failed to get the clk: -517
- [ 1.692363] pps_core: LinuxPPS API ver. 1 registered
- [ 1.697526] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- [ 1.706629] PTP clock support registered
- [ 1.711468] dmi: Firmware registration failed.
- [ 1.715524] Advanced Linux Sound Architecture Driver Initialized.
- [ 1.722334] clocksource: Switched to clocksource arch_sys_counter
- [ 1.728657] VFS: Disk quotas dquot_6.6.0
- [ 1.732676] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
- [ 1.739898] pnp: PnP ACPI: disabled
- [ 1.749210] NET: Registered protocol family 2
- [ 1.754207] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
- [ 1.762230] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
- [ 1.768778] TCP: Hash tables configured (established 8192 bind 8192)
- [ 1.775367] UDP hash table entries: 512 (order: 2, 16384 bytes)
- [ 1.781150] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
- [ 1.787882] NET: Registered protocol family 1
- [ 1.792471] RPC: Registered named UNIX socket transport module.
- [ 1.798825] RPC: Registered udp transport module.
- [ 1.803600] RPC: Registered tcp transport module.
- [ 1.808451] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 1.814913] Trying to unpack rootfs image as initramfs...
- [ 2.456056] Freeing initrd memory: 12596K
- [ 2.460423] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
- [ 2.468591] kvm [1]: 8-bit VMID
- [ 2.471676] kvm [1]: IDMAP page: 9c9000
- [ 2.475271] kvm [1]: HYP VA range: 800000000000:ffffffffffff
- [ 2.481843] kvm [1]: Hyp mode initialized successfully
- [ 2.487177] kvm [1]: vgic-v2@d1da0000
- [ 2.490625] kvm [1]: GIC system register CPU interface enabled
- [ 2.496492] kvm [1]: vgic interrupt IRQ1
- [ 2.500501] kvm [1]: virtual timer IRQ4
- [ 2.507019] audit: initializing netlink subsys (disabled)
- [ 2.512901] audit: type=2000 audit(2.402:1): state=initialized audit_enabled=0 res=1
- [ 2.512962] workingset: timestamp_bits=44 max_order=18 bucket_order=0
- [ 2.523910] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 2.531466] NFS: Registering the id_resolver key type
- [ 2.531486] Key type id_resolver registered
- [ 2.531488] Key type id_legacy registered
- [ 2.531497] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
- [ 2.531507] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
- [ 2.531708] jffs2: version 2.2. (NAND) ?? 2001-2006 Red Hat, Inc.
- [ 2.532215] 9p: Installing v9fs 9p2000 file system support
- [ 2.536248] async_tx: api initialized (async)
- [ 2.536347] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
- [ 2.540576] io scheduler noop registered
- [ 2.540635] io scheduler cfq registered (default)
- [ 2.540638] io scheduler mq-deadline registered
- [ 2.540640] io scheduler kyber registered
- [ 2.544519] OF: PCI: host bridge /soc/pcie@d0070000 ranges:
- [ 2.544536] OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000
- [ 2.544543] OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000
- [ 3.544679] advk-pcie d0070000.pcie: link never came up
- [ 3.550236] advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
- [ 3.556733] pci_bus 0000:00: root bus resource [bus 00-ff]
- [ 3.562236] pci_bus 0000:00: root bus resource [mem 0xe8000000-0xe8ffffff]
- [ 3.569330] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus address [0xe9000000-0xe900ffff])
- [ 5.010674] advk-pcie d0070000.pcie: Posted PIO Response Status: CA, 0xe00 @ 0x0
- [ 5.023768] mv_xor d0060900.xor: Marvell shared XOR driver
- [ 5.058994] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy sg intr )
- [ 5.099024] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy sg intr )
- [ 5.109083] xenfs: not registering filesystem on non-xen platform
- [ 5.117738] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
- [ 5.125791] cacheinfo: Unable to detect cache hierarchy for CPU 0
- [ 5.137077] brd: module loaded
- [ 5.146865] loop: module loaded
- [ 5.150126] hisi_sas: driver version v1.6
- [ 5.158977] ahci-mvebu d00e0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
- [ 5.168313] ahci-mvebu d00e0000.sata: flags: ncq sntf led only pmp fbs pio slum part sxs
- [ 5.177244] scsi host0: ahci-mvebu
- [ 5.180894] ata1: SATA max UDMA/133 mmio [mem 0xd00e0000-0xd00e1fff] port 0x100 irq 14
- [ 5.193219] random: fast init done
- [ 5.198505] m25p80 spi32766.0: w25q32dw (4096 Kbytes)
- [ 5.205085] libphy: Fixed MDIO Bus: probed
- [ 5.210454] tun: Universal TUN/TAP device driver, 1.6
- [ 5.216458] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
- [ 5.222423] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
- [ 5.228680] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
- [ 5.235802] igb: Copyright (c) 2007-2014 Intel Corporation.
- [ 5.241333] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
- [ 5.249633] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
- [ 5.255888] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 5.0.0-k
- [ 5.263720] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
- [ 5.269364] ixgbevf: Intel(R) 10 Gigabit PCI Express Virtual Function Network Driver - version 3.2.2-k
- [ 5.279301] ixgbevf: Copyright (c) 2009 - 2015 Intel Corporation.
- [ 5.285663] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI
- [ 5.292959] ixgb: Copyright (c) 1999-2008 Intel Corporation.
- [ 5.298700] libphy: orion_mdio_bus: probed
- [ 5.303347] mv88e6085 d0032004.mdio-mii:01: switch 0x341 detected: Marvell 88E6341, revision 0
- [ 5.320086] libphy: /soc/internal-regs@d0000000/mdio@32004/switch0@1/mdio: probed
- [ 5.348242] mvneta d0030000.ethernet eth0: Using device tree mac address f0:ad:4e:03:69:d4
- [ 5.356673] sky2: driver version 1.30
- [ 5.360559] VFIO - User Level meta-driver version: 0.3
- [ 5.366209] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 5.372806] ehci-pci: EHCI PCI platform driver
- [ 5.377542] ehci-platform: EHCI generic platform driver
- [ 5.382439] ehci-orion: EHCI orion driver
- [ 5.387074] orion-ehci d005e000.usb: EHCI Host Controller
- [ 5.392511] orion-ehci d005e000.usb: new USB bus registered, assigned bus number 1
- [ 5.400400] orion-ehci d005e000.usb: irq 12, io mem 0xd005e000
- [ 5.422346] orion-ehci d005e000.usb: USB 2.0 started, EHCI 1.00
- [ 5.429062] hub 1-0:1.0: USB hub found
- [ 5.432800] hub 1-0:1.0: 1 port detected
- [ 5.437250] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 5.443593] ohci-pci: OHCI PCI platform driver
- [ 5.447869] ohci-platform: OHCI generic platform driver
- [ 5.454032] xhci-hcd d0058000.usb: xHCI Host Controller
- [ 5.459384] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 2
- [ 5.467384] xhci-hcd d0058000.usb: hcc params 0x0a000998 hci version 0x100 quirks 0x00010010
- [ 5.476159] xhci-hcd d0058000.usb: irq 11, io mem 0xd0058000
- [ 5.482224] hub 2-0:1.0: USB hub found
- [ 5.485521] hub 2-0:1.0: 1 port detected
- [ 5.490202] xhci-hcd d0058000.usb: xHCI Host Controller
- [ 5.495537] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 3
- [ 5.503207] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
- [ 5.511814] hub 3-0:1.0: USB hub found
- [ 5.515726] hub 3-0:1.0: 1 port detected
- [ 5.519656] usbcore: registered new interface driver usb-storage
- [ 5.527199] i2c /dev entries driver
- [ 5.531792] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
- [ 5.541171] sdhci: Secure Digital Host Controller Interface driver
- [ 5.547149] sdhci: Copyright(c) Pierre Ossman
- [ 5.551825] Synopsys Designware Multimedia Card Interface Driver
- [ 5.558272] sdhci-pltfm: SDHCI platform and OF driver helper
- [ 5.564621] xenon-sdhci d00d0000.sdhci: Got CD GPIO
- [ 5.606378] mmc0: SDHCI controller on d00d0000.sdhci [d00d0000.sdhci] using ADMA
- [ 5.615282] ledtrig-cpu: registered to indicate activity on CPUs
- [ 5.623433] usbcore: registered new interface driver usbhid
- [ 5.629310] usbhid: USB HID core driver
- [ 5.634872] Initializing XFRM netlink socket
- [ 5.639069] NET: Registered protocol family 17
- [ 5.644108] 8021q: 802.1Q VLAN Support v1.8
- [ 5.648263] 9pnet: Installing 9P2000 support
- [ 5.652477] Key type dns_resolver registered
- [ 5.657095] mpls_gso: MPLS GSO support
- [ 5.661279] registered taskstats version 1
- [ 5.666412] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
- [ 5.667694] i2c i2c-0: PXA I2C adapter
- [ 5.668131] mv88e6085 d0032004.mdio-mii:01: switch 0x341 detected: Marvell 88E6341, revision 0
- [ 5.675417] libphy: /soc/internal-regs@d0000000/mdio@32004/switch0@1/mdio: probed
- [ 5.701669] DSA: switch 0 0 parsed
- [ 5.704997] ata1.00: ATA-8: OCZ-VERTEX2, 1.37, max UDMA/133
- [ 5.705002] ata1.00: 234441648 sectors, multi 1: LBA48 NCQ (depth 31/32)
- [ 5.717805] ata1.00: configured for UDMA/133
- [ 5.721763] mmc0: new high speed SDHC card at address aaaa
- [ 5.721766] DSA: tree 0 parsed
- [ 5.728140] scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX2 1.37 PQ: 0 ANSI: 5
- [ 5.740025] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/112 GiB)
- [ 5.743717] mmcblk0: mmc0:aaaa SL16G 14.8 GiB
- [ 5.751889] mmcblk0: p1
- [ 5.751965] sd 0:0:0:0: [sda] Write Protect is off
- [ 5.752037] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- [ 5.754238] sda: sda1
- [ 5.755521] sd 0:0:0:0: [sda] Attached SCSI removable disk
- [ 6.428346] Marvell 88E6390 !soc!internal-regs@d0000000!mdio@32004!switch0@1!mdio:11: attached PHY driver [Marvell 88E6390] (mii_bus:phy_addr=!soc!internal-regs@d0000000!mdio@32004!switch0@1!mdio:11, irq=-1)
- [ 6.520351] Marvell 88E6390 !soc!internal-regs@d0000000!mdio@32004!switch0@1!mdio:12: attached PHY driver [Marvell 88E6390] (mii_bus:phy_addr=!soc!internal-regs@d0000000!mdio@32004!switch0@1!mdio:12, irq=-1)
- [ 6.612351] Marvell 88E6390 !soc!internal-regs@d0000000!mdio@32004!switch0@1!mdio:13: attached PHY driver [Marvell 88E6390] (mii_bus:phy_addr=!soc!internal-regs@d0000000!mdio@32004!switch0@1!mdio:13, irq=-1)
- [ 6.631417] hctosys: unable to open rtc device (rtc0)
- [ 6.636644] ALSA device list:
- [ 6.639091] No soundcards found.
- [ 6.643613] Freeing unused kernel memory: 640K
- Loading, please wait...
- starting version 229
- Begin: Loading essential drivers ... done.
- Begin: Running /scripts/init-premount ... done.
- Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
- Begin: Running /scripts/local-premount ... done.
- Begin: Will now check root file system ... fsck from util-linux 2.27.1
- [/sbin/fsck.ext4 (1) -- /dev/sda1] fsck.ext4 -a -C0 /dev/sda1
- /dev/sda1: clean, 34252/7331840 files, 692707/29304945 blocks
- done.
- [ 7.034562] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
- done.
- Begin: Running /scripts/local-bottom ... done.
- Begin: Running /scripts/init-bottom ... done.
- [ 7.184527] systemd[1]: System time before build time, advancing clock.
- [ 7.201109] NET: Registered protocol family 10
- [ 7.206302] Segment Routing with IPv6
- [ 7.214203] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 7.229214] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
- [ 7.248032] systemd[1]: Detected architecture arm64.
- Welcome to Debian GNU/Linux 9 (stretch)!
- [ 7.266810] systemd[1]: Set hostname to <espressobin>.
- [ 7.474298] systemd[1]: Listening on Journal Socket.
- [ OK ] Listening on Journal Socket.
- [ 7.490566] systemd[1]: Reached target Remote File Systems.
- [ OK ] Reached target Remote File Systems.
- [ 7.510610] systemd[1]: Listening on Syslog Socket.
- [ OK ] Listening on Syslog Socket.
- [ 7.526609] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
- [ OK ] Listening on /dev/initctl Compatibility Named Pipe.
- [ 7.547075] systemd[1]: Created slice System Slice.
- [ OK ] Created slice System Slice.
- [ 7.564724] systemd[1]: Starting Nameserver information manager...
- Starting Nameserver information manager...
- [ 7.582908] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
- [ OK ] Started Dispatch Password Requests to Console Directory Watch.
- [ OK ] Listening on udev Kernel Socket.
- Mounting Huge Pages File System...
- Mounting Debug File System...
- Starting Set the console keyboard layout...
- [ OK ] Created slice system-serial\x2dgetty.slice.
- [ OK ] Listening on udev Control Socket.
- [ OK ] Created slice system-getty.slice.
- Starting Restore / save the current clock...
- Mounting POSIX Message Queue File System...
- Starting Load Kernel Modules...
- [ OK ] Listening on fsck to fsckd communication Socket.
- Starting Remount Root and Kernel File Systems...
- [ OK ] Listening on Journal Socket (/dev/log).
- [ 7.783729] EXT4-fs (sda1): re-mounted. Opts: commit=600,errors=remount-ro
- [ OK ] Listening on Journal Audit Socket.
- [ OK ] Started Forward Password Requests to Wall Directory Watch.
- [ OK ] Reached target Paths.
- [ OK ] Reached target Encrypted Volumes.
- [ OK ] Created slice User and Session Slice.
- [ OK ] Reached target Slices.
- Starting Create list of required st?.|ce nodes for the current kernel...
- [ OK ] Mounted Debug File System.
- [ OK ] Mounted POSIX Message Queue File System.
- [ OK ] Mounted Huge Pages File System.
- [ OK ] Started Restore / save the current clock.
- [ OK ] Started Load Kernel Modules.
- [ OK ] Started Remount Root and Kernel File Systems.
- [ OK ] Started Create list of required sta?.|vice nodes for the current kernel.
- [ OK ] Started Nameserver information manager.
- [ OK ] Started Set the console keyboard layout.
- Starting Create Static Device Nodes in /dev...
- Activating swap /var/swap...
- Starting Load/Save Random Seed...
- Starting udev Coldplug all Devices...
- Mounting Configuration File System...
- Starting Apply Kernel Variables...
- [ OK ] Mounted Configuration File System.
- [ OK ] Started Create Static Device Nodes in /dev.
- [FAILED] Failed to activate swap /var/swap.
- See 'systemctl status var-swap.swap' for details.
- [DEPEND] Dependency failed for Swap.
- [ OK ] Started Load/Save Random Seed.
- [ OK ] Started Apply Kernel Variables.
- [ OK ] Reached target Local File Systems (Pre).
- Mounting /tmp...
- Starting udev Kernel Device Manager...
- [ OK ] Mounted /tmp.
- [FAILED] Failed to start Entropy daemon using the HAVEGE algorithm.
- See 'systemctl status haveged.service' for details.
- [ OK ] Reached target Local File Systems.
- Starting Set console font and keymap...
- Starting Armbian enhanced Log2Ram...
- Starting Raise network interfaces...
- [ OK ] Started udev Kernel Device Manager.
- [ OK ] Started udev Coldplug all Devices.
- [ OK ] Started Set console font and keymap.
- [ OK ] Started Armbian enhanced Log2Ram.
- Starting Journal Service...
- [ OK ] Started Journal Service.
- Starting Flush Journal to Persistent Storage...
- [ 8.611681] systemd-journald[1357]: Received request to flush runtime journal from PID 1
- [ OK ] Started Flush Journal to Persistent Storage.
- Starting Create Volatile Files and Directories...
- [FAILED] Failed to start Create Volatile Files and Directories.
- See 'systemctl status systemd-tmpfiles-setup.service' for details.
- Starting Update UTMP about System Boot/Shutdown...
- [ OK ] Reached target System Time Synchronized.
- [ OK ] Started Update UTMP about System Boot/Shutdown.
- [ OK ] Reached target System Initialization.
- [ OK ] Started Daily Cleanup of Temporary Directories.
- [ OK ] Listening on D-Bus System Message Bus Socket.
- [ OK ] Listening on lircd.socket.
- [ OK ] Reached target Sockets.
- [ OK ] Reached target Basic System.
- Starting LSB: Armbian gathering hardware information...
- Starting LSB: Load kernel modules needed to enable cpufreq scaling...
- Starting System Logging Service...
- [ OK ] Started D-Bus System Message Bus.
- Starting lircd(8) initialization helper tool...
- [ OK ] Started Convert IR remotes button p?.|ses to mouse movements and clicks.
- [ 9.063722] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- Starting Login Service...
- Starting Network Manager...
- [ OK ] Started Regular background program processing daemon.
- Starting LSB: Start/stop sysstat's sadc...
- [ OK ] Started Handle events from IR remotes decoded by lircd(8).
- [ OK ] Started System Logging Service.
- [ OK ] Found device /dev/ttyS0.
- [ OK ] Started LSB: Start/stop sysstat's sadc.
- [ OK ] Found device /dev/ttyMV0.
- [ OK ] Started Login Service.
- [ OK ] Started LSB: Load kernel modules needed to enable cpufreq scaling.
- Starting LSB: set CPUFreq kernel parameters...
- [ OK ] Started LSB: set CPUFreq kernel parameters.
- Starting LSB: Set sysfs variables from /etc/sysfs.conf...
- [ OK ] Started Network Manager.
- Starting Network Manager Wait Online...
- [ 9.855890] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
- [ OK ] Started LSB: Set sysfs variables from /etc/sysfs.conf.
- Starting Network Manager Script Dispatcher Service...
- [ 10.016841] br0: port 1(lan0) entered blocking state
- [ 10.026445] br0: port 1(lan0) entered disabled state
- [ 10.033315] device lan0 entered promiscuous mode
- [ 10.033321] device eth0 entered promiscuous mode
- [ OK ] Started Network Manager Script Dispatcher Service.
- [ 10.094440] mvneta d0030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
- [ OK ] Found device /sys/subsystem/net/devices/eth0.
- [ 10.119758] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- [ OK ] Started ifup for eth0.
- [FAILED] Failed to start Hostname Service.
- [ 10.162478] br0: port 2(lan1) entered blocking state
- [ 10.167612] br0: port 2(lan1) entered disabled state
- See 'systemctl status systemd-hostnamed.service' for details.
- [ 10.178882] device lan1 entered promiscuous mode
- [ 10.234380] br0: port 3(wan) entered blocking state
- [ 10.240991] br0: port 3(wan) entered disabled state
- [ 10.253203] device wan entered promiscuous mode
- [ OK ] Started lircd(8) initialization helper tool.
- [ 10.295438] IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready
- [ OK ] Found device /sys/subsystem/net/devices/lan0.
- [ OK ] Started ifup for lan0.
- [ OK ] Found device /sys/subsystem/net/devices/lan1.
- [ OK ] Started ifup for lan1.
- [ 11.257148] mv88e6085 d0032004.mdio-mii:01 lan0: Link is Down
- [ 11.317852] mv88e6085 d0032004.mdio-mii:01 lan1: Link is Down
- [ 11.348879] mv88e6085 d0032004.mdio-mii:01 wan: Link is Down
- [ OK ] Started LSB: Armbian gathering hardware information.
- [ 13.397356] mv88e6085 d0032004.mdio-mii:01 wan: Link is Up - 1Gbps/Full - flow control off
- [ 13.405690] br0: port 3(wan) entered blocking state
- [ 13.410795] br0: port 3(wan) entered forwarding state
- [ 13.417783] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
- [ OK ] Started Raise network interfaces.
- [ OK ] Reached target Network.
- [ OK ] Started Flexible IR remote input/output application support.
- [ OK ] Started Forward LIRC button presses as uinput events.
- [ OK ] Started Unattended Upgrades Shutdown.
- Starting Permit User Sessions...
- Starting OpenBSD Secure Shell server...
- [ OK ] Started Permit User Sessions.
- [ OK ] Started Serial Getty on ttyMV0.
- [ OK ] Started Serial Getty on ttyS0.
- [ OK ] Started Getty on tty1.
- [ OK ] Reached target Login Prompts.
- [ OK ] Started OpenBSD Secure Shell server.
- Debian GNU/Linux 9 espressobin ttyMV0
- espressobin login: root
- Password:
- Last login: Sat Aug 19 15:17:25 UTC 2017 on ttyMV0
- _____ _ _
- | ____|___ _ __ _ __ ___ ___ ___ ___ | |__ (_)_ __
- | _| / __| '_ \| '__/ _ \/ __/ __|/ _ \| '_ \| | '_ \
- | |___\__ \ |_) | | | __/\__ \__ \ (_) | |_) | | | | |
- |_____|___/ .__/|_| \___||___/___/\___/|_.__/|_|_| |_|
- |_|
- Welcome to ARMBIAN 5.32.170817 nightly Debian GNU/Linux 9 (stretch) 4.12.1-ebin-g4b13ed5-dirty
- System load: 0.68 0.17 0.06 Up time: 0 min
- Memory usage: 4 % of 992MB IP:
- HDD temp: 30??C
- Usage of /: 1% of 111G storage/: 1% of 111G
- root@espressobin:~#
Add Comment
Please, Sign In to add comment