API tools faq
paste
Advertisement
Guest User

Untitled

a guest
Jan 15th, 2019
556
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 8.28 KB | None | 0 0
raw download clone embed print report
  1. EEEE I3000000032940xf100110303B77500EEEE I400000004294_M8_BL1_10221D113B323EEEE I3000000032940xbbbb000026A22525
  2. no sdio debug board detected
  3. TE : 102615
  4. BT : 15:39:25 May 30 2015
  5. PMU:rn5t618
  6. DC01 v:1100, 0x[36]: 18 -> 28
  7. DC02 v:1150, 0x[37]: 18 -> 2c
  8. DC03 v:1500, 0x[38]: 38 -> 48
  9. LDO01 v:2900, 0x[4c]: 4e -> 50
  10. LDO02 v:1800, 0x[4d]: 24 -> 24
  11. LDO03 v:1800, 0x[4e]: 30 -> 30
  12. LDO04 v:2850, 0x[4f]: 4e -> 4e
  13. LDO05 v:1800, 0x[50]: 24 -> 24
  14. LDO0a v:2700, 0x[56]: 28 -> 28
  15. LDO0b v:900, 0x[57]: 00 -> 00
  16.  
  17. CPU clock is 1200MHz
  18.  
  19. CPU type: M8
  20. DDR info: 1GB(auto) @ 528MHz(1T)
  21. DDR channel: DDR 0 + DDR 1
  22.  
  23. DDR init use : 12477 us
  24.  
  25. HHH
  26. Boot From SPI
  27. ucl decompress...pass
  28. 0x12345678
  29. Boot from internal device 1st SPI
  30.  
  31. TE : 472840
  32.  
  33. System Started
  34.  
  35.  
  36. U-boot-00000-ga716940(m8_k200_v1@s82_netxeon_tronsmart) (May 30 2015 - 15:39:15)
  37.  
  38. clr h-ram
  39. DRAM: 1 GiB
  40. relocation Offset is: 2fec0000
  41. show partition table:
  42. part: 0, name : logo, size : 2000000
  43. part: 1, name : recovery, size : 2000000
  44. part: 2, name : misc, size : 2000000
  45. part: 3, name : boot, size : 2000000
  46. part: 4, name : system, size : 40000000
  47. part: 5, name : cache, size : 20000000
  48. part: 6, name : data, size : end
  49. aml_card_type=0x100
  50. MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
  51. [mmc_register] add mmc dev_num=1, port=2, if_type=6
  52. SDIO Port B: 0, SDIO Port C: 1
  53. PMU fault status:
  54. reg[0x9A] = 0x1d
  55. LSI version:04, OTP version:0c
  56. PMU type:RN5T618
  57. register usb cfg[0][1] = 3ff6fccc
  58. register usb cfg[2][0] = 3ff731dc
  59. NAND: SPI BOOT: boot_device_flag 0
  60. Nand PHY driver Version: 1.01.001.0004 (c) 2013 Amlogic Inc.
  61. amlnf_phy_init : amlnf init flag 0
  62. NAND device id: 2c 64 44 4b a9 0 0 0
  63. detect NAND device: B revision NAND 8GiB MT29F64G08CBABA
  64. AML_NAND_NEW_OOB : new oob
  65. bus_cycle=5, bus_timing=7,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
  66. NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 5, valid_page_addr = 0
  67. NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 7, valid_page_addr = 0
  68. NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 4, valid_page_addr = 179
  69. i=0,register --- nand_key
  70. nfcache : offset: 0x000006000000 -0x000024800000 : partitons 1 : single_chip multi_plane
  71. nfcode : offset: 0x00002a800000 -0x000050800000 : partitons 5 : single_chip multi_plane
  72. nfdata : offset: 0x00007b000000 -0x000185000000 : partitons 1 : single_chip multi_plane
  73. bad block count = 0
  74.  
  75. bad block count = 0
  76.  
  77. bad block count = 0
  78.  
  79. amlnf_logic_init: START
  80. aml_nftl_start:117,size_in_blk=145,tmp_block=128,part->free_block_num=17
  81. aml_nftl_start:117,size_in_blk=321,tmp_block=288,part->free_block_num=33
  82. amlnf_logic_init: COMPLETE
  83. get_boot_device_flag: init_ret 0
  84. get_boot_device_flag SPI BOOT:
  85. nand init success, change the device_boot_flag to 4 : spi+nand
  86. SPI BOOT,spi_env_relocate_spec : env_relocate_spec 53
  87. SF: Detected MX25L1605D with page size 256, total 2 MiB
  88.  
  89. SPI NOR Flash have write protect!!!
  90. set_storage_device_flag: store 4
  91. Err imgread(L129):Fmt unsupported!genFmt 0x0 != 0x3
  92. check dts: FDT_ERR_BADMAGIC, load default vpu parameters
  93. vpu driver detect cpu type: m8
  94. vpu clk_level = 7
  95. set vpu clk: 364300000Hz, readback: 364300000Hz(0x700)
  96. Net: Meson_Ethernet
  97. init suspend firmware done. (ret:0)
  98. cvbs trimming.1.v5: 0xa0, 0x2
  99. cvbs performance type = 0, table = 0
  100. vdac open.1 = 0x1, 0x2
  101. [ImgPck]ver=2
  102. reboot_mode=charging
  103. efuse version is not selected.
  104. Hit Enter key to stop autoboot -- : 0
  105. exit abortboot: 0
  106. (Re)start USB(0)...
  107. USB: dwc_usb driver version: 2.94 6-June-2012
  108. USB (1) peri reg base: c1108820
  109. USB (1) use clock source: XTAL input
  110. USB (1) base addr: 0xc90c0000
  111. Force id mode: Host
  112. dwc_otg: Highspeed device found !
  113.  
  114. scanning bus for devices... 1 USB Device(s) found
  115. scanning bus for storage devices... 0 Storage Device(s) found
  116.  
  117. ** Invalid boot device **
  118.  
  119. ** Invalid boot device **
  120.  
  121. ** Invalid boot device **
  122.  
  123. ** Invalid boot device **
  124. sdio_detect return 1
  125. [mmc_init] SDIO Port B:0, if_type=7, initialized OK!
  126. Device: SDIO Port B
  127. Manufacturer ID: 0
  128. OEM: 0
  129. Name: 'Tran Speed: 20000000
  130. Rd Block Len: 512
  131. SD version 2.0
  132. High Capacity: Yes
  133. Capacity: 7969177600
  134. Boot Part Size: 0
  135. Bus Width: 4-bit
  136. reading s805_autoscript
  137.  
  138. 1760 bytes read
  139. ## Executing script at 11000000
  140. reading uImage
  141.  
  142. 10760768 bytes read
  143. reading uInitrd
  144.  
  145. 8290626 bytes read
  146. reading uEnv.ini
  147.  
  148. 242 bytes read
  149. reading /dtb/mxiii.dtb
  150.  
  151. ** Unable to read "/dtb/mxiii.dtb" from mmc 0:1 **
  152. Err imgread(L129):Fmt unsupported!genFmt 0x0 != 0x3
  153. ## Booting kernel from Legacy Image at 14000000 ...
  154. Image Name: Linux-5.0.0-rc2-next-20190115-am
  155. Image Type: ARM Linux Kernel Image (uncompressed)
  156. Data Size: 10760704 Bytes = 10.3 MiB
  157. Load Address: 00208000
  158. Entry Point: 00208000
  159. Verifying Checksum ... OK
  160. ## Loading init Ramdisk from Legacy Image at 15000000 ...
  161. Image Name: uInitrd
  162. Image Type: ARM Linux RAMDisk Image (gzip compressed)
  163. Data Size: 8290562 Bytes = 7.9 MiB
  164. Load Address: 00000000
  165. Entry Point: 00000000
  166. Verifying Checksum ... OK
  167. ERROR: Did not find a cmdline Flattened Device Tree
  168. Could not find a valid device tree
  169.  
  170. ** Invalid boot device **
  171.  
  172. ** Invalid boot device **
  173.  
  174. ** Invalid boot device **
  175.  
  176. ** Invalid boot device **
  177. reading emmc_autoscript
  178.  
  179. 758 bytes read
  180. ## Executing script at 11000000
  181. reading uImage
  182.  
  183. 10760768 bytes read
  184. reading uInitrd
  185.  
  186. 8290626 bytes read
  187. reading uEnv.ini
  188.  
  189. 242 bytes read
  190. reading /dtb/mxiii.dtb
  191.  
  192. ** Unable to read "/dtb/mxiii.dtb" from mmc 0:1 **
  193. MMC: block number 0x1 exceeds max(0x0)
  194. ** Can't read from device 1 **
  195.  
  196. ** Unable to use mmc 1:1 for fatload **
  197. Unknown command 'ext4load' - try 'help'
  198. MMC: block number 0x1 exceeds max(0x0)
  199. ** Can't read from device 1 **
  200.  
  201. ** Unable to use mmc 1:1 for fatload **
  202. Unknown command 'ext4load' - try 'help'
  203. current storer:nand_key
  204. key save is auto select storer(nand or emmc)
  205. write key code version3_flush:708,prov->write:3fee8470
  206. size:4096
  207. arg_pages:1
  208. extra_page:0
  209. write key ok!!
  210. Booting...
  211. error: image data is not a fdt
  212. key_unify_init:364,unify key config table parse fail
  213. Err key(L47):fail in key_drv_init
  214. Err imgread(L330):Fmt unsupported!genFmt 0x0 != 0x3
  215. Wrong Image Format for bootm command
  216. ERROR: can't get kernel image!
  217. enter recovery
  218. Device: SDIO Port B
  219. Manufacturer ID: 0
  220. OEM: 0
  221. Name: 'Tran Speed: 20000000
  222. Rd Block Len: 512
  223. SD version 2.0
  224. High Capacity: Yes
  225. Capacity: 7969177600
  226. Boot Part Size: 0
  227. Bus Width: 4-bit
  228. reading recovery.img
  229.  
  230. ** Unable to read "recovery.img" from mmc 0:1 **
  231. board_usb_stop cfg: 0
  232. (Re)start USB(0)...
  233. USB: dwc_usb driver version: 2.94 6-June-2012
  234. USB (1) peri reg base: c1108820
  235. USB (1) use clock source: XTAL input
  236. USB (1) base addr: 0xc90c0000
  237. Force id mode: Host
  238. dwc_otg: Highspeed device found !
  239.  
  240. scanning bus for devices... 1 USB Device(s) found
  241. scanning bus for storage devices... 0 Storage Device(s) found
  242.  
  243. ** Invalid boot device **
  244. ## ANDROID Format IMAGE
  245. ## Booting kernel from Legacy Image at 12000000 ...
  246. Image Name: Linux-3.10.33
  247. Image Type: ARM Linux Kernel Image (lzo compressed)
  248. Data Size: 6517077 Bytes = 6.2 MiB
  249. Load Address: 00208000
  250. Entry Point: 00208000
  251. Verifying Checksum ... OK
  252. Ramdisk start addr = 0x12638000, len = 0x1f595b
  253. Multi dtb tool version: v2 .
  254. Multi dtb detected, support 6 dtbs.
  255. aml_dt soc: m8 platform: k200 variant: sdhc
  256. dtb 0 soc: m8 plat: k200 vari: 2gsdhc
  257. dtb 1 soc: m8 plat: k200 vari: 2gsdio
  258. dtb 2 soc: m8 plat: k200 vari: sdhc
  259. dtb 3 soc: m8 plat: k200 vari: sdio
  260. dtb 4 soc: m8m2 plat: n200 vari: 1G
  261. dtb 5 soc: m8m2 plat: n200 vari: 2G
  262. Find match dtb: 2
  263. Flat device tree start addr = 0x12839000, len = 0x511e magic=0xedfe0dd0
  264. board_usb_stop cfg: 0
  265. Uncompressing Kernel Image ... OK
  266. uboot time: 19988140 us.
  267. EFUSE machid is not set.
  268. Using machid 0xf81 from environment
  269. From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x51ff001
  270. Loading Ramdisk to 05009000, end 051fe95b ... OK
  271. Loading Device Tree to 05000000, end 0500811d ... OK
  272.  
  273. Starting kernel ...
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!