API tools faq
paste
Advertisement
LaserOval

coco-bot config file on 11/17/20

LaserOval
Nov 17th, 2020
63
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 31.09 KB | None | 0 0
raw download clone embed print report
  1. # Smoothieboard configuration file, see http://smoothieware.org/configuring-smoothie
  2. # NOTE Lines must not exceed 132 characters, and '#' characters mean what follows is ignored
  3. ## Robot module configurations : general handling of movement G-codes and slicing into moves
  4.  
  5. # Basic motion configuration
  6. default_feed_rate 4000 # Default speed (mm/minute) for G1/G2/G3 moves
  7. default_seek_rate 4000 # Default speed (mm/minute) for G0 moves
  8. mm_per_arc_segment 0.0 # Fixed length for line segments that divide arcs, 0 to disable
  9. #mm_per_line_segment 5 # Cut lines into segments this size
  10. mm_max_arc_error 0.0 # The maximum error for line segments that divide arcs 0 to disable
  11. # note it is invalid for both the above be 0
  12. # if both are used, will use largest segment length based on radius
  13. grbl_mode true # using bCNC as firmware=
  14.  
  15. # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
  16. # See http://smoothieware.org/stepper-motors
  17. alpha_steps_per_mm 12 # Steps per mm for alpha ( X ) stepper
  18. beta_steps_per_mm 12 # Steps per mm for beta ( Y ) stepper
  19. gamma_steps_per_mm 1600 # Steps per mm for gamma ( Z ) stepper, gamma is the laser, not a stepper, should this be ignored?
  20.  
  21. # Planner module configuration : Look-ahead and acceleration configuration
  22. # See http://smoothieware.org/motion-control
  23. acceleration 3000 # Acceleration in mm/second/second.
  24. #z_acceleration 500 # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA
  25. junction_deviation 0.05 # See http://smoothieware.org/motion-control#junction-deviation
  26. #z_junction_deviation 0.0 # For Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA
  27.  
  28. # Cartesian axis speed limits
  29. x_axis_max_speed 3000 # Maximum speed in mm/min
  30. y_axis_max_speed 3000 # Maximum speed in mm/min
  31. z_axis_max_speed 300 # Maximum speed in mm/min, gamma is the laser, not a stepper, should this be ignored?
  32.  
  33. # Stepper module configuration
  34. # Pins are defined as ports, and pin numbers, appending "!" to the number will invert a pin
  35. # See http://smoothieware.org/pin-configuration and http://smoothieware.org/pinout
  36. alpha_step_pin 2.0 # Pin for alpha stepper step signal
  37. alpha_dir_pin 0.5 # Pin for alpha stepper direction, add '!' to reverse direction
  38. alpha_en_pin 0.4 # Pin for alpha enable pin
  39. alpha_current 0.9 # X stepper motor current
  40. alpha_max_rate 30000.0 # Maximum rate in mm/min
  41.  
  42. beta_step_pin 2.1 # Pin for beta stepper step signal
  43. beta_dir_pin 0.11 # Pin for beta stepper direction, add '!' to reverse direction
  44. beta_en_pin 0.10 # Pin for beta enable
  45. beta_current 0.9 # Y stepper motor current
  46. beta_max_rate 30000.0 # Maxmimum rate in mm/min
  47.  
  48. gamma_step_pin 2.2 # Pin for gamma stepper step signal
  49. gamma_dir_pin 0.20 # Pin for gamma stepper direction, add '!' to reverse direction
  50. gamma_en_pin 0.19 # Pin for gamma enable
  51. gamma_current 0 # Z stepper motor current
  52. gamma_max_rate 300.0 # Maximum rate in mm/min
  53.  
  54. ## Extruder module configuration
  55. # See http://smoothieware.org/extruder
  56. extruder.hotend.enable false # Whether to activate the extruder module at all. All configuration is ignored if false
  57. extruder.hotend.steps_per_mm 140 # Steps per mm for extruder stepper
  58. extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  59. extruder.hotend.acceleration 500 # Acceleration for the stepper motor mm/sec²
  60. extruder.hotend.max_speed 50 # Maximum speed in mm/s
  61.  
  62. extruder.hotend.step_pin 2.3 # Pin for extruder step signal
  63. extruder.hotend.dir_pin 0.22 # Pin for extruder dir signal ( add '!' to reverse direction )
  64. extruder.hotend.en_pin 0.21 # Pin for extruder enable signal
  65.  
  66. # Extruder offset
  67. #extruder.hotend.x_offset 0 # X offset from origin in mm
  68. #extruder.hotend.y_offset 0 # Y offset from origin in mm
  69. #extruder.hotend.z_offset 0 # Z offset from origin in mm
  70.  
  71. # Firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
  72. #extruder.hotend.retract_length 3 # Retract length in mm
  73. #extruder.hotend.retract_feedrate 45 # Retract feedrate in mm/sec
  74. #extruder.hotend.retract_recover_length 0 # Additional length for recover
  75. #extruder.hotend.retract_recover_feedrate 8 # Recover feedrate in mm/sec (should be less than retract feedrate)
  76. #extruder.hotend.retract_zlift_length 0 # Z-lift on retract in mm, 0 disables
  77. #extruder.hotend.retract_zlift_feedrate 6000 # Z-lift feedrate in mm/min (Note mm/min NOT mm/sec)
  78.  
  79. #delta_current 1.5 # First extruder stepper motor current
  80.  
  81. # Second extruder module configuration
  82. #extruder.hotend2.enable False # Whether to activate the extruder module at all. All configuration is ignored if false
  83. #extruder.hotend2.steps_per_mm 140 # Steps per mm for extruder stepper
  84. #extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  85. #extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
  86. #extruder.hotend2.max_speed 50 # mm/s
  87.  
  88. #extruder.hotend2.step_pin 2.8 # Pin for extruder step signal
  89. #extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal ( add '!' to reverse direction )
  90. #extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal
  91.  
  92. #extruder.hotend2.x_offset 0 # x offset from origin in mm
  93. #extruder.hotend2.y_offset 25.0 # y offset from origin in mm
  94. #extruder.hotend2.z_offset 0 # z offset from origin in mm
  95.  
  96. #epsilon_current 1.5 # Second extruder stepper motor current
  97.  
  98.  
  99. ## Laser module configuration
  100. # See http://smoothieware.org/laser
  101. laser_module_enable True # Whether to activate the laser module at all
  102. laser_module_pwm_pin 2.5 # This pin will be PWMed to control the laser.
  103. # Only pins 2.0, 2.1, 2.2, 2.3, 2.4, 2.5, 1.18, 1.20, 1.21, 1.23, 1.24, 1.26, 3.25 and 3.26
  104. laser_module_ttl_pin 1.30 # This pin turns on when the laser turns on, and off when the laser turns off.
  105. laser_module_maximum_power 1.0 # This is the maximum duty cycle that will be applied to the laser
  106. laser_module_minimum_power 0.1 # This is a value just below the minimum duty cycle that keeps the laser
  107. # active without actually burning.
  108. laser_module_default_power 0.8 # This is the default laser power that will be used for cuts if a power has not been specified. The value is a scale between
  109. # the maximum and minimum power levels specified above
  110. laser_module_pwm_period 200 # This sets the pwm frequency as the period in microseconds. LW4 asked this to be 200
  111.  
  112. ## Temperature control configuration
  113. # See http://smoothieware.org/temperaturecontrol
  114.  
  115. # First hotend configuration
  116. temperature_control.hotend.enable false # Whether to activate this ( "hotend" ) module at all.
  117. temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read
  118. temperature_control.hotend.heater_pin 2.7 # Pin that controls the heater, set to nc if a readonly thermistor is being defined
  119. temperature_control.hotend.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#toc5
  120. #temperature_control.hotend.beta 4066 # Or set the beta value
  121. temperature_control.hotend.set_m_code 104 # M-code to set the temperature for this module
  122. temperature_control.hotend.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  123. temperature_control.hotend.designator T # Designator letter for this module
  124. #temperature_control.hotend.max_temp 300 # Set maximum temperature - Will prevent heating above 300 by default
  125. #temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below if set
  126.  
  127. # Safety control is enabled by default and can be overidden here, the values show the defaults
  128. # See http://smoothieware.org/temperaturecontrol#runaway
  129. #temperature_control.hotend.runaway_heating_timeout 900 # How long it can take to heat up, max is 2040 seconds.
  130. #temperature_control.hotend.runaway_cooling_timeout 0 # How long it can take to cool down if temp is set lower, max is 2040 seconds
  131. #temperature_control.hotend.runaway_range 20 # How far from the set temperature it can wander, max setting is 63°C
  132.  
  133. # PID configuration
  134. # See http://smoothieware.org/temperaturecontrol#pid
  135. #temperature_control.hotend.p_factor 13.7 # P ( proportional ) factor
  136. #temperature_control.hotend.i_factor 0.097 # I ( integral ) factor
  137. #temperature_control.hotend.d_factor 24 # D ( derivative ) factor
  138.  
  139. #temperature_control.hotend.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
  140.  
  141. # Second hotend configuration
  142. #temperature_control.hotend2.enable false # Whether to activate this ( "hotend" ) module at all.
  143. #temperature_control.hotend2.thermistor_pin 0.25 # Pin for the thermistor to read
  144. #temperature_control.hotend2.heater_pin 1.23 # Pin that controls the heater
  145. #temperature_control.hotend2.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#thermistor
  146. ##temperature_control.hotend2.beta 4066 # or set the beta value
  147. #temperature_control.hotend2.set_m_code 104 # M-code to set the temperature for this module
  148. #temperature_control.hotend2.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  149. #temperature_control.hotend2.designator T1 # Designator letter for this module
  150.  
  151. #temperature_control.hotend2.p_factor 13.7 # P ( proportional ) factor
  152. #temperature_control.hotend2.i_factor 0.097 # I ( integral ) factor
  153. #temperature_control.hotend2.d_factor 24 # D ( derivative ) factor
  154.  
  155. #temperature_control.hotend2.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
  156.  
  157. temperature_control.bed.enable false # Whether to activate this ( "hotend" ) module at all.
  158. temperature_control.bed.thermistor_pin 0.24 # Pin for the thermistor to read
  159. temperature_control.bed.heater_pin 2.5 # Pin that controls the heater
  160. temperature_control.bed.thermistor Honeywell100K # See http://smoothieware.org/temperaturecontrol#thermistor
  161. #temperature_control.bed.beta 3974 # Or set the beta value
  162. temperature_control.bed.set_m_code 140 # M-code to set the temperature for this module
  163. temperature_control.bed.set_and_wait_m_code 190 # M-code to set-and-wait for this module
  164. temperature_control.bed.designator B # Designator letter for this module
  165.  
  166. # Bang-bang ( simplified ) control
  167. # See http://smoothieware.org/temperaturecontrol#bang-bang
  168. #temperature_control.bed.bang_bang false # Set to true to use bang bang control rather than PID
  169. #temperature_control.bed.hysteresis 2.0 # Set to the temperature in degrees C to use as hysteresis
  170.  
  171. ## Switch modules
  172. # See http://smoothieware.org/switch
  173.  
  174. # Switch module for fan control
  175. switch.fan_one.enable true # Enable this module. Intake fan, left BOTTOM
  176. switch.fan_one.input_on_command M106 # Command that will turn this switch on
  177. switch.fan_one.input_off_command M107 # Command that will turn this switch off
  178. switch.fan_one.output_pin 2.6 # Pin this module controls
  179. switch.fan_one.output_type pwm # PWM output settable with S parameter in the input_on_comand
  180. switch.fan_one.max_pwm 255 # Set max pwm for the pin default is 255
  181. switch.fan_one.startup_state true #start up state of the switch, you want always on
  182.  
  183. switch.fan_two.enable true # Enable this module. Exhaust Fan, TOP right side
  184. switch.fan_two.input_on_command M106 # Command that will turn this switch on
  185. switch.fan_two.input_off_command M107 # Command that will turn this switch off
  186. switch.fan_two.output_pin 2.4 # Pin this module controls
  187. switch.fan_two.output_type pwm # PWM output settable with S parameter in the input_on_comand
  188. switch.fan_two.max_pwm 255 # Set max pwm for the pin default is 255
  189. switch.fan_two.startup_state true #start up state of the switch, you want always on
  190.  
  191. switch.fan_three.enable true # Enable this module, Exhaust fan BOTTOM right
  192. switch.fan_three.input_on_command M106 # Command that will turn this switch on
  193. switch.fan_three.input_off_command M107 # Command that will turn this switch off
  194. switch.fan_three.output_pin 2.7 # Pin this module controls
  195. switch.fan_three.output_type pwm # PWM output settable with S parameter in the input_on_comand
  196. switch.fan_three.max_pwm 255 # Set max pwm for the pin default is 255
  197. switch.fan_three.startup_state true #start up state of the switch, you want always on
  198.  
  199. switch.fan_four.enable true # Enable this module Intake fan left TOP
  200. switch.fan_four.input_on_command M106 # Command that will turn this switch on
  201. switch.fan_four.input_off_command M107 # Command that will turn this switch off
  202. switch.fan_four.output_pin 2.5 # Pin this module controls
  203. switch.fan_four.output_type pwm # PWM output settable with S parameter in the input_on_comand
  204. switch.fan_four.max_pwm 255 # Set max pwm for the pin default is 255
  205. switch.fan_four.startup_state true #start up state of the switch, you want always on
  206.  
  207.  
  208. #switch.misc.enable true # Enable this module
  209. #switch.misc.input_on_command M42 # Command that will turn this switch on
  210. #switch.misc.input_off_command M43 # Command that will turn this switch off
  211. #switch.misc.output_pin 2.4 # Pin this module controls
  212. #switch.misc.output_type digital # Digital means this is just an on or off pin
  213.  
  214. #switch.bltouch.enable true #
  215. #switch.bltouch.output_pin 2.4 # sw pwm can use any digital pin
  216. #switch.bltouch.input_on_command M280 #
  217. #switch.bltouch.input_off_command M281 #
  218. #switch.bltouch.output_type swpwm # sw pwm must be low frequency
  219. #switch.bltouch.pwm_period_ms 20 # 50Hz
  220. #switch.bltouch.startup_state false # start up in the stow state
  221. #switch.bltouch.startup_value 7.43 # On boot it will go into stow mode, also set with the M281
  222. #switch.bltouch.default_on_value 3.3 # if M280 is issued without S this is the value it will set it to
  223.  
  224.  
  225. ## Temperatureswitch
  226. # See http://smoothieware.org/temperatureswitch
  227. # Automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
  228. # Useful to turn on a fan or water pump to cool the hotend
  229. #temperatureswitch.hotend.enable true #
  230. #temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor
  231. #temperatureswitch.hotend.switch misc # select which switch to use, matches the name of the defined switch
  232. #temperatureswitch.hotend.threshold_temp 60.0 # temperature to turn on (if rising) or off the switch
  233. #temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals
  234. #temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals
  235.  
  236. ## Endstops
  237. # See http://smoothieware.org/endstops
  238. endstops_enable true # The endstop module is enabled by default and can be disabled here
  239. #corexy_homing false # Set to true if homing on a hbot or corexy
  240. #alpha_min_endstop 1.24^! # X Axis-Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  241. #alpha_max_endstop 1.25^! # X Axis-Pin to read max endstop, uncomment this and comment the above if using max endstops
  242. #alpha_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  243. #alpha_min 0 # This gets loaded as the current position after homing when home_to_min is set
  244. #alpha_max 200 # This gets loaded as the current position after homing when home_to_max is set
  245. beta_min_endstop 1.26^ # Y Axis-Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  246. beta_max_endstop 1.27^ # Y Axis-Pin to read max endstop, uncomment this and comment the above if using max endstops
  247. #beta_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  248. #beta_min 0 # This gets loaded as the current position after homing when home_to_min is set
  249. #beta_max 200 # This gets loaded as the current position after homing when home_to_max is set
  250. gamma_min_endstop 1.28^! # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  251. gamma_max_endstop 1.29^! # Pin to read max endstop, uncomment this and comment the above if using max endstops
  252. #gamma_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  253. #gamma_min 0 # This gets loaded as the current position after homing when home_to_min is set
  254. #gamma_max 200 # This gets loaded as the current position after homing when home_to_max is set
  255.  
  256. #alpha_max_travel 200 # X Axis Max travel in mm for alpha/X axis when homing
  257. #beta_max_travel 400 # Y Axis-Max travel in mm for beta/Y axis when homing
  258. #gamma_max_travel 500 # Max travel in mm for gamma/Z axis when homing
  259.  
  260. # Optional enable limit switches, actions will stop if any enabled limit switch is triggered
  261. alpha_limit_enable false # Set to true to enable X min and max limit switches
  262. beta_limit_enable true # Set to true to enable Y min and max limit switches
  263. gamma_limit_enable true # Set to true to enable Z min and max limit switches
  264.  
  265. # Endstops home at their fast feedrate first, then once the endstop is found they home again at their slow feedrate for accuracy
  266. alpha_fast_homing_rate_mm_s 50 # Alpha/X fast homing feedrate in mm/second
  267. alpha_slow_homing_rate_mm_s 25 # Alpha/X slow homing feedrate in mm/second
  268. beta_fast_homing_rate_mm_s 50 # Beta/Y fast homing feedrate in mm/second
  269. beta_slow_homing_rate_mm_s 25 # Beta/Y slow homing feedrate in mm/second
  270. gamma_fast_homing_rate_mm_s 4 # Gamma/Z fast homing feedrate in mm/second
  271. gamma_slow_homing_rate_mm_s 2 # Gamma/Z slow homing feedrate in mm/second
  272.  
  273. alpha_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for alpha/X
  274. beta_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for beta/Y
  275. gamma_homing_retract_mm 1 # Distance to retract from the endstop after it is hit for gamma/Z
  276.  
  277.  
  278. # Optional enable limit switches, actions will stop if any enabled limit switch is triggered (all are set for delta)
  279. #alpha_limit_enable true # Set to true to enable X min and max limit switches
  280. #beta_limit_enable true # Set to true to enable Y min and max limit switches
  281. #gamma_limit_enable false # Set to true to enable Z min and max limit switches
  282.  
  283. # Optional order in which axis will home, default is they all home at the same time,
  284. # If this is set it will force each axis to home one at a time in the specified order
  285. #homing_order YX # X axis followed by Y then Z last
  286. #move_to_origin_after_home false # Move XY to 0,0 after homing
  287. #endstop_debounce_count 100 # Uncomment if you get noise on your endstops, default is 100
  288. #endstop_debounce_ms 1 # Uncomment if you get noise on your endstops, default is 1 millisecond debounce
  289. #home_z_first true # Uncomment and set to true to home the Z first, otherwise Z homes after XY
  290.  
  291. # End of endstop config
  292. # Delete the above endstop section and uncomment next line and copy and edit Snippets/abc-endstop.config file to enable endstops for ABC axis
  293. #include abc-endstop.config
  294.  
  295. ## Z-probe
  296. # See http://smoothieware.org/zprobe
  297. zprobe.enable false # Set to true to enable a zprobe
  298. #zprobe.probe_pin 1.28!^ # Pin probe is attached to, if NC remove the !
  299. zprobe.slow_feedrate 5 # Mm/sec probe feed rate
  300. #zprobe.debounce_ms 1 # Set if noisy
  301. zprobe.fast_feedrate 100 # Move feedrate mm/sec
  302. zprobe.probe_height 5 # How much above bed to start probe
  303. #gamma_min_endstop nc # Normally 1.28. Change to nc to prevent conflict,
  304.  
  305. # Levelling strategy
  306. # Example for 3-point levelling strategy, see wiki documentation for other strategies
  307. #leveling-strategy.three-point-leveling.enable true # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane
  308. #leveling-strategy.three-point-leveling.point1 100.0,0.0 # the first probe point (x,y) optional may be defined with M557
  309. #leveling-strategy.three-point-leveling.point2 200.0,200.0 # the second probe point (x,y)
  310. #leveling-strategy.three-point-leveling.point3 0.0,200.0 # the third probe point (x,y)
  311. #leveling-strategy.three-point-leveling.home_first true # home the XY axis before probing
  312. #leveling-strategy.three-point-leveling.tolerance 0.03 # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm
  313. #leveling-strategy.three-point-leveling.probe_offsets 0,0,0 # the probe offsets from nozzle, must be x,y,z, default is no offset
  314. #leveling-strategy.three-point-leveling.save_plane false # set to true to allow the bed plane to be saved with M500 default is false
  315.  
  316. ## Panel
  317. # See http://smoothieware.org/panel
  318. # Please find your panel on the wiki and copy/paste the right configuration here
  319. panel.enable false # Set to true to enable the panel code
  320.  
  321. # Example for reprap discount GLCD
  322. # on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
  323. # +5v is EXP1 pin 10, Gnd is EXP1 pin 9
  324. #panel.lcd reprap_discount_glcd #
  325. #panel.spi_channel 0 # SPI channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
  326. #panel.spi_cs_pin 0.16 # SPI chip select ; GLCD EXP1 Pin 4
  327. #panel.encoder_a_pin 3.25!^ # Encoder pin ; GLCD EXP2 Pin 3
  328. #panel.encoder_b_pin 3.26!^ # Encoder pin ; GLCD EXP2 Pin 5
  329. #panel.click_button_pin 1.30!^ # Click button ; GLCD EXP1 Pin 2
  330. #panel.buzz_pin 1.31 # Pin for buzzer ; GLCD EXP1 Pin 1
  331. #panel.back_button_pin 2.11!^ # Back button ; GLCD EXP2 Pin 8
  332.  
  333. panel.menu_offset 0 # Some panels will need 1 here
  334.  
  335. panel.alpha_jog_feedrate 6000 # X jogging feedrate in mm/min
  336. panel.beta_jog_feedrate 6000 # Y jogging feedrate in mm/min
  337. panel.gamma_jog_feedrate 200 # Z jogging feedrate in mm/min
  338.  
  339. panel.hotend_temperature 185 # Temp to set hotend when preheat is selected
  340. panel.bed_temperature 60 # Temp to set bed when preheat is selected
  341.  
  342. ## Custom menus : Example of a custom menu entry, which will show up in the Custom entry.
  343. # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
  344. custom_menu.power_on.enable true #
  345. custom_menu.power_on.name Power_on #
  346. custom_menu.power_on.command M80 #
  347.  
  348. custom_menu.power_off.enable true #
  349. custom_menu.power_off.name Power_off #
  350. custom_menu.power_off.command M81 #
  351.  
  352.  
  353. ## Network settings
  354. # See http://smoothieware.org/network
  355. network.enable false # Enable the ethernet network services
  356. network.webserver.enable true # Enable the webserver
  357. network.telnet.enable true # Enable the telnet server
  358. network.ip_address auto # Use dhcp to get ip address
  359. # Uncomment the 3 below to manually setup ip address
  360. #network.ip_address 192.168.3.222 # The IP address
  361. #network.ip_mask 255.255.255.0 # The ip mask
  362. #network.ip_gateway 192.168.3.1 # The gateway address
  363. #network.mac_override xx.xx.xx.xx.xx.xx # Override the mac address, only do this if you have a conflict
  364.  
  365. ## System configuration
  366. # Serial communications configuration ( baud rate defaults to 9600 if undefined )
  367. # For communication over the UART port, *not* the USB/Serial port
  368. uart0.baud_rate 115200 # Baud rate for the default hardware ( UART ) serial port
  369.  
  370. second_usb_serial_enable false # This enables a second USB serial port
  371. #leds_disable true # Disable using leds after config loaded
  372. #play_led_disable true # Disable the play led
  373.  
  374. # Kill button maybe assigned to a different pin, set to the onboard pin by default
  375. # See http://smoothieware.org/killbutton
  376. kill_button_enable true # Set to true to enable a kill button
  377. kill_button_pin 2.12 # Kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
  378.  
  379. #msd_disable false # Disable the MSD (USB SDCARD), see http://smoothieware.org/troubleshooting#disable-msd
  380. #dfu_enable false # For linux developers, set to true to enable DFU
  381.  
  382. # Only needed on a smoothieboard
  383. # See http://smoothieware.org/currentcontrol
  384. currentcontrol_module_enable true # Control stepper motor current via the configuration file
  385.  
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!