Wandboard Dual - Android 4.1.2

U-Boot 2009.08 (Apr 11 2013 – 15:55:59)CPU: Freescale i.MX6 family TO1.1 at 792 MHz
Temperature: 67 C, calibration data 0x59952b5f
mx6q pll1: 792MHz
mx6q pll2: 528MHz
mx6q pll3: 480MHz
mx6q pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 99000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
nfc clock : 24000000Hz
Board: i.MX6DL/Solo-WandBoard: unknown-board Board: 0x61011 [WDOG ]
Boot Device: SD
DRAM: 1 GB
MMC: FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2
*** Warning – bad CRC or MMC, using default environmentIn: serial
Out: serial
Err: serial
Gotr MAC = 00:1F:7B:B2:02:F4
Net: got MAC address from IIM: 00:1f:7b:b2:02:f4
FEC0 [PRIME]
Hit any key to stop autoboot: 0
kernel @ 10808000 (2289836)
ramdisk @ 11800000 (169948)
kernel cmdline:
use boot.img command line:
console=ttymxc0,115200 init=/init video=mxcfb0:dev=hdmi,1280x720M@60,ifStarting kernel …

[ 0.000000] Linux version 3.0.35 (root@edward-x220-laptop) (gcc version 4.6.3
[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Freescale i.MX 6DualLite/Solo Wandboard
[ 0.000000] EDWARD : ram console init at phys 0x3ff00000
[ 0.000000] EDWARD : GPU_Reserved Memory equals to 184549376
[ 0.000000] EDWARD : gpumem init at phys 0x15000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] CPU identified as i.MX6DL/SOLO, silicon rev 1.1
[ 0.000000] PERCPU: Embedded 7 pages/cpu @80f67000 s5696 r8192 d14784 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pa0
[ 0.000000] Kernel command line: console=ttymxc0,115200 init=/init video=mxce
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 80MB 511MB 212MB = 803MB total
[ 0.000000] Memory: 805480k/805480k available, 243096k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 – 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 – 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xfbe00000 – 0xffe00000 ( 64 MB)
[ 0.000000] vmalloc : 0xc0800000 – 0xf2000000 ( 792 MB)
[ 0.000000] lowmem : 0x80000000 – 0xc0000000 (1024 MB)
[ 0.000000] pkmap : 0x7fe00000 – 0x80000000 ( 2 MB)
[ 0.000000] modules : 0x7f000000 – 0x7fe00000 ( 14 MB)
[ 0.000000] .init : 0x80008000 – 0x80038000 ( 192 kB)
[ 0.000000] .text : 0x80038000 – 0x805de000 (5784 kB)
[ 0.000000] .data : 0x805de000 – 0x80620f80 ( 268 kB)
[ 0.000000] .bss : 0x80620fa4 – 0x8075ffe0 (1277 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, 1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:496
[ 0.000000] MXC GPIO hardware
[ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1s
[ 0.000000] Set periph_clk’s parent to pll2_pfd_400M!
[ 0.000000] arm_max_freq=2
[ 0.000000] MXC_Early serial console at MMIO 0x2020000 (options ‘115200’)
[ 0.000000] bootconsole [ttymxc0] enabled
[ 0.000000] Console: colour dummy device 80×30
[ 0.245885] Calibrating delay loop… 1581.05 BogoMIPS (lpj=7905280)
[ 0.334225] pid_max: default: 32768 minimum: 301
[ 0.339085] Mount-cache hash table entries: 512
[ 0.344360] CPU: Testing write buffer coherency: ok
[ 0.450152] CPU1: Booted secondary processor
[ 0.539562] Brought up 2 CPUs
[ 0.546824] SMP: Total of 2 processors activated (3162.11 BogoMIPS).
[ 0.571679] print_constraints: dummy:
[ 0.575671] NET: Registered protocol family 16
[ 0.584294] print_constraints: vddpu: 725 1300 mV at 700 mV fast normal
[ 0.591792] print_constraints: vddcore: 725 1300 mV at 1150 mV fast nor
[ 0.599531] print_constraints: vddsoc: 725 1300 mV at 1200 mV fast norm
[ 0.607166] print_constraints: vdd2p5: 2000 2775 mV at 2400 mV fast nor
[ 0.614921] print_constraints: vdd1p1: 800 1400 mV at 1100 mV fast norm
[ 0.622591] print_constraints: vdd3p0: 2625 3400 mV at 3000 mV fast nor
[ 0.632723] ram_console: got buffer at 3ff00000, size 100000
[ 0.638535] ram_console: found existing buffer, size 35924, start 35924
[ 0.738384] console [ram-1] enabled
[ 0.853886] L310 cache controller enabled
[ 0.858092] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x02050000, Cache sB
[ 0.891189] bio: create slab at 0
[ 0.896073] print_constraints: VDDA: 2500 mV
[ 0.900747] print_constraints: VDDIO: 3300 mV
[ 0.906244] SCSI subsystem initialized
[ 0.910531] spi_imx imx6q-ecspi.0: probed
[ 0.914905] spi_imx imx6q-ecspi.1: probed
[ 0.921083] usbcore: registered new interface driver usbfs
[ 0.926918] usbcore: registered new interface driver hub
[ 0.932514] usbcore: registered new device driver usb
[ 0.937753] Freescale USB OTG Driver loaded, $Revision: 1.55 $
[ 0.959552] imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F)
[ 0.967929] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.975414] Bluetooth: Core ver 2.16
[ 0.979212] NET: Registered protocol family 31
[ 0.983777] Bluetooth: HCI device and connection manager initialized
[ 0.990329] Bluetooth: HCI socket layer initialized
[ 0.995311] Bluetooth: L2CAP socket layer initialized
[ 1.000555] Bluetooth: SCO socket layer initialized
[ 1.006009] cfg80211: Calling CRDA to update world regulatory domain
[ 1.013552] Switching to clocksource mxc_timer1
[ 1.031297] NET: Registered protocol family 2
[ 1.035969] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 1.044176] TCP established hash table entries: 131072 (order: 8, 1048576 by)
[ 1.054110] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 1.061942] TCP: Hash tables configured (established 131072 bind 65536)
[ 1.068925] TCP reno registered
[ 1.072178] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 1.078354] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 1.085163] NET: Registered protocol family 1
[ 1.089892] Unpacking initramfs…
[ 1.104517] Freeing initrd memory: 164K
[ 1.108540] _regulator_get: etb supply vcore not found, using dummy regulator
[ 1.116394] _regulator_get: etm.0 supply vcore not found, using dummy regular
[ 1.124000] _regulator_get: etm.1 supply vcore not found, using dummy regular
[ 1.131799] Static Power Management for Freescale i.MX6
[ 1.137211] wait mode is disabled for i.MX6
[ 1.141702] cpaddr = c0820000 suspend_iram_base=c08ac000
[ 1.147282] PM driver module loaded
[ 1.151249] IMX usb wakeup probe
[ 1.154662] the wakeup pdata is 0xba10d980
[ 1.159272] add wake up source irq 75
[ 1.166674] IMX usb wakeup probe
[ 1.170101] the wakeup pdata is 0xba10d380
[ 1.174498] cpu regulator init ldo=0
[ 1.178494] i.MXC CPU frequency driver
[ 1.193907] ashmem: initialized
[ 1.206930] NTFS driver 2.1.30 [Flags: R/O].
[ 1.211784] fuse init (API version 7.16)
[ 1.216175] msgmni has been set to 1573
[ 1.220878] NET: Registered protocol family 38
[ 1.225640] cryptodev: driver loaded.
[ 1.229435] io scheduler noop registered
[ 1.233445] io scheduler deadline registered
[ 1.237941] io scheduler cfq registered (default)
[ 1.243863] mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi
[ 1.250576] mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0x1a:0xa0:0xc1
[ 1.257649] fbcvt: 1280×720@60: CVT Name – .921M9
[ 1.328272] imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2)
[ 1.339386] imx-sdma imx-sdma: loaded firmware 1.1
[ 1.348667] imx-sdma imx-sdma: initialized
[ 1.353209] Serial: IMX driver
[ 1.356501] imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
[ 1.363098] console [ttymxc0] enabled, bootconsole disabled
[ 1.363098] console [ttymxc0] enabled, bootconsole disabled
[ 1.374893] imx-uart.2: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX
[ 1.382337] ion: failed to create debug files.
[ 1.390269] loop: module loaded
[ 1.393806] FEC Ethernet Driver
[ 1.399457] fec_enet_mii_bus: probed
[ 1.404138] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 1.410914] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 1.417758] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number1
[ 1.445550] fbcvt: 1280×720@60: CVT Name – .921M9
[ 1.458239] fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
[ 1.478225] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 1.478840] hub 1-0:1.0: USB hub found
[ 1.478859] hub 1-0:1.0: 1 port detected
[ 1.479061] add wake up source irq 72
[ 1.479108] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
[ 1.479146] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number2
[ 1.508239] fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
[ 1.568231] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
[ 1.568751] hub 2-0:1.0: USB hub found
[ 1.568769] hub 2-0:1.0: 1 port detected
[ 1.569014] Initializing USB Mass Storage driver…
[ 1.569191] usbcore: registered new interface driver usb-storage
[ 1.569200] USB Mass Storage support registered.
[ 1.569207] ARC USBOTG Device Controller driver (1 August 2005)
[ 1.571543] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 1.571554] android_usb gadget: Number of LUNs=1
[ 1.571563] lun0: LUN: removable file: (no medium)
[ 1.571976] Gadget Android: controller ‘fsl-usb2-udc’ not recognized
[ 1.571992] android_usb gadget: android_usb ready
[ 1.571998] Suspend udc for OTG auto detect
[ 1.572011] USB Host suspend begins
[ 1.572017] will suspend roothub and its children
[ 1.572034] ehci_fsl_bus_suspend begins, DR
[ 1.572055] ehci_fsl_bus_suspend ends, DR
[ 1.572069] host suspend ends
[ 1.572079] USB Gadget resume begins
[ 1.572085] fsl_udc_resume, Wait for wakeup thread finishes
[ 1.588243] dr_controller_run: udc enter low power mode
[ 1.588257] USB Gadget resume ends
[ 1.588264] fsl-usb2-udc: bind to driver android_usb
[ 1.588623] mousedev: PS/2 mouse device common for all mice
[ 1.589446] i2c /dev entries driver
[ 1.590367] imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s ()
[ 1.590500] Bluetooth: Virtual HCI driver ver 1.3
[ 1.590665] Bluetooth: HCI UART driver ver 2.2
[ 1.590674] Bluetooth: HCI H4 protocol initialized
[ 1.590682] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 1.590838] usbcore: registered new interface driver btusb
[ 1.591034] cpuidle: using governor ladder
[ 1.591042] cpuidle: using governor menu
[ 1.591155] sdhci: Secure Digital Host Controller Interface driver
[ 1.591163] sdhci: Copyright(c) Pierre Ossman
[ 1.591279] _regulator_get: sdhci-esdhc-imx.2 supply vmmc not found, using dr
[ 1.591529] mmc0: SDHCI controller on platform [sdhci-esdhc-imx.2] using ADMA
[ 1.592600] _regulator_get: sdhci-esdhc-imx.1 supply vmmc not found, using dr
[ 1.594892] mmc1: SDHCI controller on platform [sdhci-esdhc-imx.1] using ADMA
[ 1.594949] sdhci sdhci-esdhc-imx.0: no write-protect pin available!
[ 1.595985] _regulator_get: sdhci-esdhc-imx.0 supply vmmc not found, using dr
[ 1.598163] mmc2: SDHCI controller on platform [sdhci-esdhc-imx.0] using ADMA
[ 1.599163] VPU initialized
[ 1.600129] mxc_asrc registered
[ 1.613568] revserved_memory_account:viv_gpu registerd
[ 1.614174] Thermal calibration data is 0x59952b5f
[ 1.628463] Anatop Thermal registered as thermal_zone0
[ 1.628628] anatop_thermal_probe: default cooling device is cpufreq!
[ 1.651107] usbcore: registered new interface driver usbhid
[ 1.651115] usbhid: USB HID core driver
[ 1.653535] logger: created 256K log ‘log_main’
[ 1.655731] logger: created 256K log ‘log_events’
[ 1.655910] logger: created 256K log ‘log_radio’
[ 1.658127] logger: created 256K log ‘log_system’
[ 1.661501] zram: num_devices not specified. Using default: 1
[ 1.661510] zram: Creating 1 devices …
[ 1.662414] usbcore: registered new interface driver snd-usb-audio
[ 1.662976] mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
[ 1.663145] mxc_spdif mxc_spdif.0: MXC SPDIF Audio
[ 1.665520] _regulator_get: 1-000a supply VDDD not found, using dummy regular
[ 1.665836] sgtl5000 1-000a: sgtl5000 revision 17
[ 1.666016] print_constraints: 1-000a: 850 1600 mV at 1200 mV normal
[ 1.732249] asoc: sgtl5000 imx-ssi.1 mapping ok
[ 1.745029] asoc: mxc-spdif imx-spdif-dai.0 mapping ok
[ 1.758656] asoc: mxc-hdmi-soc imx-hdmi-soc-dai.0 mapping ok
[ 1.763333] ALSA device list:
[ 1.763341] #0: sgtl5000-audio
[ 1.763347] #1: imx-spdif
[ 1.763352] #2: imx-hdmi-soc
[ 1.763489] GACT probability NOT on
[ 1.763502] Mirror/redirect action on
[ 1.763510] u32 classifier
[ 1.763514] Actions configured
[ 1.763522] Netfilter messages via NETLINK v0.30.
[ 1.763571] nf_conntrack version 0.5.0 (12588 buckets, 50352 max)
[ 1.764463] ctnetlink v0.93: registering with nfnetlink.
[ 1.764503] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 1.764511] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 1.765241] xt_time: kernel timezone is -0000
[ 1.765954] IPv4 over IPv4 tunneling driver
[ 1.767126] GRE over IPv4 demultiplexor driver
[ 1.767807] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.767945] arp_tables: (C) 2002 David S. Miller
[ 1.767996] TCP cubic registered
[ 1.769282] NET: Registered protocol family 10
[ 1.773276] Mobile IPv6
[ 1.773312] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 1.773536] IPv6 over IPv4 tunneling driver
[ 1.778363] NET: Registered protocol family 17
[ 1.778408] NET: Registered protocol family 15
[ 1.796703] Bluetooth: RFCOMM TTY layer initialized
[ 1.796714] Bluetooth: RFCOMM socket layer initialized
[ 1.796722] Bluetooth: RFCOMM ver 1.11
[ 1.796730] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.796737] Bluetooth: BNEP filters: protocol multicast
[ 1.796746] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.796882] mmc0: new high speed SDHC card at address 59b4
[ 1.797072] L2TP core driver, V2.0
[ 1.797080] L2TP IP encapsulation support (L2TPv3)
[ 1.797510] mmcblk0: mmc0:59b4 SD 14.7 GiB
[ 1.797717] L2TP netlink interface
[ 1.797743] L2TP ethernet pseudowire support (L2TPv3)
[ 1.797751] lib80211: common routines for IEEE802.11 drivers
[ 1.797760] lib80211_crypt: registered algorithm ‘NULL’
[ 1.797767] VFP support v0.3: implementor 41 architecture 3 part 30 variant 4
[ 1.882447] ThumbEE CPU extension supported.
[ 1.887281] Bus freq driver module loaded
[ 1.887291] Bus freq driver Enabled
[ 1.887358] mxc_dvfs_core_probe
[ 1.887565] DVFS driver module loaded
[ 1.892653] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.913882] mmcblk0: p1 p2 p3 < p5 p6 p7 p8 p9 > p4
[ 2.188839] Freeing init memory: 192K
[ 4.311415] init: cannot find ‘/system/etc/install-recovery.sh’, disabling ”
[ 4.333127] android_usb: already disabled
[ 4.337524] mtp_bind_config
[ 4.340602] adb_bind_config
[ 4.345090] adb_open
root@android:/ #

Read more: http://www.cnx-software.com/2013/06/11/wandboard-dual-benchmarks-serial-console-fun-and-distributions-list/#ixzz3S9li1xjV