boot_ok

radxa@rock-3a:~$ xzcat ./rock-3a_debian_bullseye_cli_b25.img.xz | sudo dd of=/dev/nvme0n1 bs=1M
[sudo] password for radxa:
0+311043 records in
0+311043 records out
2588079104 bytes (2.6 GB, 2.4 GiB) copied, 63.0415 s, 41.1 MB/s
radxa@rock-3a:~$
{HERE POWERED OFF/ON}

DDR Version V1.10 20210810
In
ddrconfig:0
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=2048MB
tdqss: cs0 dqs0: 48ps, dqs1: -24ps, dqs2: -48ps, dqs3: -120ps,

change to: 324MHz
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x61

change to: 528MHz
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58

change to: 780MHz
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58

change to: 1056MHz(final freq)
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:22%
dram drv:40,odt:80
vref_ca:00000071
clk skew:0x29
cs 0:
the read training result:
DQS0:0x43, DQS1:0x41, DQS2:0x41, DQS3:0x3f,
min  : 0xb  0xc  0xd  0xb  0x1  0x5  0x6  0x3 , 0xa  0x8  0x2  0x1  0xb  0x9  0xa  0x6 ,
      0x10  0xe  0xb  0x9  0x3  0x2  0x2  0x5 , 0xa  0x7  0x7  0x1  0xb  0xd  0xb  0xd ,
mid  :0x2d 0x2e 0x2e 0x2d 0x23 0x27 0x28 0x25 ,0x2a 0x28 0x22 0x22 0x2b 0x29 0x2a 0x26 ,
      0x2f 0x2e 0x2b 0x29 0x23 0x22 0x23 0x25 ,0x2a 0x28 0x27 0x22 0x2c 0x2d 0x2c 0x2d ,
max  :0x4f 0x50 0x50 0x50 0x45 0x49 0x4b 0x48 ,0x4a 0x48 0x43 0x43 0x4c 0x49 0x4b 0x47 ,
      0x4e 0x4f 0x4c 0x4a 0x44 0x43 0x44 0x46 ,0x4a 0x49 0x48 0x43 0x4d 0x4e 0x4d 0x4d ,
range:0x44 0x44 0x43 0x45 0x44 0x44 0x45 0x45 ,0x40 0x40 0x41 0x42 0x41 0x40 0x41 0x41 ,
      0x3e 0x41 0x41 0x41 0x41 0x41 0x42 0x41 ,0x40 0x42 0x41 0x42 0x42 0x41 0x42 0x40 ,
the write training result:
DQS0:0x2f, DQS1:0x26, DQS2:0x23, DQS3:0x19,
min  :0x5c 0x5d 0x5e 0x5c 0x52 0x55 0x56 0x57 0x56 ,0x4e 0x4e 0x49 0x49 0x50 0x4e 0x50 0x4f 0x4c ,
      0x51 0x51 0x4c 0x4c 0x46 0x43 0x45 0x4a 0x4a ,0x48 0x46 0x45 0x41 0x4a 0x4a 0x48 0x4b 0x43 ,
mid  :0x79 0x7a 0x7c 0x79 0x6e 0x71 0x73 0x73 0x72 ,0x6c 0x6b 0x64 0x66 0x6d 0x6b 0x6d 0x6b 0x69 ,
      0x6f 0x6e 0x6a 0x69 0x63 0x5f 0x61 0x66 0x66 ,0x65 0x61 0x60 0x5d 0x65 0x66 0x63 0x67 0x5f ,
max  :0x97 0x98 0x9a 0x96 0x8b 0x8e 0x91 0x90 0x8f ,0x8a 0x88 0x80 0x83 0x8b 0x88 0x8a 0x87 0x86 ,
      0x8d 0x8c 0x88 0x87 0x80 0x7c 0x7d 0x83 0x83 ,0x82 0x7d 0x7c 0x7a 0x81 0x83 0x7e 0x84 0x7c ,
range:0x3b 0x3b 0x3c 0x3a 0x39 0x39 0x3b 0x39 0x39 ,0x3c 0x3a 0x37 0x3a 0x3b 0x3a 0x3a 0x38 0x3a ,
      0x3c 0x3b 0x3c 0x3b 0x3a 0x39 0x38 0x39 0x39 ,0x3a 0x37 0x37 0x39 0x37 0x39 0x36 0x39 0x39 ,
CA Training result:
cs:0 min  :0x49 0x45 0x40 0x3c 0x40 0x38 0x46 ,0x48 0x43 0x40 0x3b 0x3e 0x38 0x46 ,
cs:0 mid  :0x87 0x86 0x7d 0x7d 0x7e 0x79 0x73 ,0x86 0x83 0x7c 0x7b 0x7b 0x79 0x73 ,
cs:0 max  :0xc5 0xc7 0xbb 0xbe 0xbc 0xba 0xa0 ,0xc4 0xc3 0xb9 0xbb 0xb9 0xba 0xa0 ,
cs:0 range:0x7c 0x82 0x7b 0x82 0x7c 0x82 0x5a ,0x7c 0x80 0x79 0x80 0x7b 0x82 0x5a ,
out
U-Boot SPL board init
U-Boot SPL 2017.09-gef9f6b1caad-211223 #stephen (Sep 24 2022 - 17:13:02)
Trying to boot from MMC2
MMC error: The cmd index is 1, ret is -110
Card did not respond to voltage select!
mmc_init: -95, time 10
spl: mmc init failed with error: -95
Trying to boot from MMC1
MMC error: The cmd index is 0, ret is -110
mmc_init: -110, time 5
spl: mmc init failed with error: -110
Trying to boot from MTD2
No misc partition
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(fe4f274c06...) + OK
## Checking uboot 0x00a00000 ... sha256(b0dd8071c5...) + OK
## Checking fdt 0x00b2f8d0 ... sha256(877bce1efa...) + OK
## Checking atf-2 0x00068000 ... sha256(8d44036095...) + OK
## Checking atf-3 0xfdcd0000 ... sha256(e410275b51...) + OK
## Checking atf-4 0xfdcc9000 ... sha256(990c53fc01...) + OK
## Checking atf-5 0x00066000 ... sha256(315a4195a9...) + OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 539.168 ms

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-181-gc9a647cae:cl
NOTICE:  BL31: Built : 10:55:41, Oct 18 2021
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    pmu v1 is valid
INFO:    dfs DDR fsp_param[0].freq_mhz= 1056MHz
INFO:    dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO:    dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO:    dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0xa00000
INFO:    SPSR = 0x3c9


U-Boot 2017.09-gef9f6b1caad-211223 #stephen (Sep 24 2022 - 17:13:02 +0800)

Model: Radxa ROCK3 Model A
PreSerial: 2, raw, 0xfe660000
DRAM:  2 GiB
Sysmem: init
Relocation Offset: 7d349000
Relocation fdt: 7b9f75a0 - 7b9fecd0
CR: M/C/I
Using default environment

SF: Detected sfc_nor with page size 256 Bytes, erase size 4 KiB, total 16 MiB
Bootdev(atags): mtd 2
PartType: EFI
No misc partition
boot mode: None
FIT: No boot partition
No resource partition
No resource partition
Failed to load DTB, ret=-19
Failed to get kernel dtb, ret=-19
I2c0 speed: 100000Hz
vsel-gpios- not found! Error: -2
vdd_cpu 1025000 uV
PMIC:  RK8090 (on=0x40, off=0x00)
vdd_logic init 900000 uV
vdd_gpu init 900000 uV
vdd_npu init 900000 uV
io-domain: OK
Model: Radxa ROCK3 Model A
rockchip_set_serialno: could not find efuse/otp device
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
  apll 816000 KHz
  dpll 528000 KHz
  gpll 1188000 KHz
  cpll 1000000 KHz
  npll 24000 KHz
  vpll 24000 KHz
  hpll 24000 KHz
  ppll 200000 KHz
  armclk 816000 KHz
  aclk_bus 150000 KHz
  pclk_bus 50000 KHz
  aclk_top_high 300000 KHz
  aclk_top_low 200000 KHz
  hclk_top 150000 KHz
  pclk_top 50000 KHz
  aclk_perimid 300000 KHz
  hclk_perimid 150000 KHz
  pclk_pmu 100000 KHz
No misc partition
Net:   No ethernet found.
Hit key to stop autoboot('CTRL+C'):  0

Device 0: Vendor: 0x1f40 Rev: 1004A    Prod: AA20241028128G874410
            Type: Hard Disk
            Capacity: 122104.3 MB = 119.2 GB (250069680 x 512)
... is now current device
Scanning nvme 0:2...
Scanning nvme 0:3...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
1339 bytes read in 2 ms (653.3 KiB/s)
U-Boot menu
1:      Debian GNU/Linux 11 (bullseye) 5.10.160-12-rk356x
2:      Debian GNU/Linux 11 (bullseye) 5.10.160-12-rk356x (rescue target)
Enter choice: 1:        Debian GNU/Linux 11 (bullseye) 5.10.160-12-rk356x
Retrieving file: /boot/initrd.img-5.10.160-12-rk356x
fs_devread read outside partition 17222521455656991744
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
Skipping l0 for failure retrieving initrd
2:      Debian GNU/Linux 11 (bullseye) 5.10.160-12-rk356x (rescue target)
Retrieving file: /boot/initrd.img-5.10.160-12-rk356x
8186906 bytes read in 20 ms (390.4 MiB/s)
Retrieving file: /boot/vmlinuz-5.10.160-12-rk356x
28176896 bytes read in 57 ms (471.4 MiB/s)
append: root=UUID=502efe26-7c43-49ff-bfce-9e9c230defdb quiet splash loglevel=4 rw earlycon consoleblank=0 console=tty0 console=ttyFIQ0,1500000n8 console=ttyAML0,115200n8 console=ttyS2,1500000n8 console=ttyS0,1500000n8 coherent_pool=2M e
Retrieving file: /usr/lib/linux-image-5.10.160-12-rk356x/rockchip/rk3568-rock-3a.dtb
165720 bytes read in 39 ms (4.1 MiB/s)
Fdt Ramdisk skip relocation
No misc partition
## Flattened Device Tree blob at 0x0a100000
   Booting using the fdt blob at 0x0a100000
  'reserved-memory' ramoops@110000: addr=110000 size=f0000
   Using Device Tree in place at 000000000a100000, end 000000000a12b757
Adding bank: 0x00200000 - 0x80000000 (size: 0x7fe00000)
Total: 2643.496 ms

Starting kernel ...

[    3.211787] fiq_debugger fiq_debugger.0: IRQ fiq not found
[    3.211853] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[    3.211888] fiq_debugger_probe: could not install nmi irq handler
[    4.683825] rk-pcie 3c0000000.pcie: IRQ msi not found
[    4.683907] rk-pcie 3c0000000.pcie: Missing *config* reg space
[    4.684187] rk-pcie 3c0000000.pcie: Missing *config* reg space
[    4.684272] rk-pcie 3c0000000.pcie: invalid resource
[    4.693746] mpp-iep2 fdef0000.iep: allocate roi buffer failed
[    4.694364] rk-pcie 3c0800000.pcie: IRQ msi not found
[    4.694434] rk-pcie 3c0800000.pcie: Missing *config* reg space
[    4.694694] rk-pcie 3c0800000.pcie: Missing *config* reg space
[    4.694775] rk-pcie 3c0800000.pcie: invalid resource
[    4.715621] arm-scmi firmware:scmi: Failed. SCMI protocol 22 not active.
[    4.740923] dwhdmi-rockchip fe0a0000.hdmi: IRQ index 1 not found
[    4.744605] no ATF memory for init
[    4.766509] no ATF memory for init
[    4.782049] rk_gmac-dwmac fe010000.ethernet: no regulator found
[    5.196887] rk817-battery rk817-battery: Failed to find matching dt id
[    5.197335] rk817-charger rk817-charger: Failed to find matching dt id
[    5.230717] rkisp_hw fdff0000.rkisp: can't request region for resource [mem 0xfdff0000-0xfdffffff]
[    5.251185] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
[    5.257412] rksfc_base v1.1 2016-01-08
[    5.296637] mpp_rkvenc fdf40000.rkvenc: Failed to get leakage
[    5.297105] mpp_rkvenc fdf40000.rkvenc: failed to find power_model node
[    5.297129] mpp_rkvenc fdf40000.rkvenc: failed to initialize power model
[    5.297141] mpp_rkvenc fdf40000.rkvenc: failed to get dynamic-coefficient
[    5.298666] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_a is not found!
[    5.298696] rkvdec2_init:1022: No niu aclk reset resource define
[    5.298711] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_h is not found!
[    5.298722] rkvdec2_init:1025: No niu hclk reset resource define
[    5.299428] mpp_rkvdec2 fdf80200.rkvdec: failed to find power_model node
[    5.299451] mpp_rkvdec2 fdf80200.rkvdec: failed to initialize power model
[    5.299464] mpp_rkvdec2 fdf80200.rkvdec: failed to get dynamic-coefficient
[    5.302233] rockchip-dmc dmc: failed to get vop pn to msch rl
[    5.302884] rockchip-dmc dmc: could not find power_model node
[    5.306394] adc_keys adc-keys: keymap is missing
[    7.583291] rk-pcie 3c0000000.pcie: PCIe Link Fail
[    7.583406] rk-pcie 3c0000000.pcie: failed to initialize host

Cannot open access to console, the root account is locked.
See sulogin(8) man page for more details.

Press Enter to continue.
[    9.703923] rk-multicodecs rk809-sound: ASoC: Property 'rockchip,audio-routing' does not exist or its length is not even
[    9.947120] of_dma_request_slave_channel: dma-names property of node '/serial@fe650000' missing or empty
[   12.233432] Bluetooth: hci0: command 0xfc18 tx timeout
[   20.123579] Bluetooth: hci0: BCM: failed to write update baudrate (-110)
[   20.123737] Bluetooth: hci0: Failed to set baudrate
[   22.256918] Bluetooth: hci0: command 0x0c03 tx timeout
[   30.150182] Bluetooth: hci0: BCM: Reset failed (-110)


Debian GNU/Linux 11 rock-3a ttyFIQ0

rock-3a login: radxa
Password:
Linux rock-3a 5.10.160-12-rk356x #fd78925da SMP Tue Aug 29 11:45:05 UTC 2023 aarch64

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
radxa@rock-3a:~$