Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- ; General preferences
- G90 ; send absolute coordinates...
- M83 ; ...but relative extruder moves
- M912 P0 S-4.5 ; Calibrated CPU temperature
- M667 S1 ; select CoreXY mode
- ; Network
- M550 P"HEVO" ; set printer name
- M552 S1 ; enable network
- M586 P0 S1 ; enable HTTP
- M586 P1 S0 ; disable FTP
- M586 P2 S0 ; disable Telnet
- ; Drives
- M569 P0 S1 ; physical drive 0 goes forwards
- M569 P1 S1 ; physical drive 1 goes forwards
- M569 P2 S1 ; physical drive 2 goes forwards
- ;M569 P3 S1 ; Forwards for Zesty Nimble
- ;M569 P3 S0 ; Backwards for reverse mounted BMG on E0
- M569 P4 S0 ; Backwards for reverse mounted BMG on E1
- M584 X0 Y1 Z2 E4 ; set drive mapping
- M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
- ; M92 X80.00 Y80.00 Z1600.00 E2609.00 ; Set steps per mm Zesty Nimble
- ; M92 X80.00 Y80.00 Z1600.00 E257.8 ; B2B Extrudr test
- M92 X80.00 Y80.00 Z1600.00 E423 ; Bontech BMG
- M566 X900.00 Y900.00 Z20.00 E40.00 ; Set maximum instantaneous speed changes (mm/min)
- M203 X10800.00 Y10800.00 Z480.00 E1200.00 ; Set maximum speeds (mm/min)
- M201 X2000.00 Y2000.00 Z150.00 E120.00 ; Set accelerations (mm/s^2)
- M906 X850.00 Y850.00 Z950.00 E800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
- M84 S300 ; Set idle timeout
- ; Axis Limits
- M208 X0 Y-30 Z0 S1 ; Set axis minima
- M208 X290 Y260 Z250 S0 ; Set axis maxima
- ; Endstops
- M574 X1 S0 P"xstop" ; configure active-low endstop for low end on X via pin xstop
- M574 Y1 S0 P"ystop" ; configure active-low endstop for low end on Y via pin ystop
- M574 Z1 S0 P"null" ; configure active-low endstop for low end on Z via pin null
- ; Z-Probe
- M558 P8 I1 A1 R1 C"zprobe.in" H5 F950 T6000 ; set Z probe type to effector and the dive height + speeds
- G31 P100 X0 Y0 Z-0.030 ; Z mit "G30 S-1" 8x bei 160 Grad gemessen => Mittelwert
- M557 X0:290 Y0:260 S30:30 ; define mesh grid
- ; Temp sensors configuration
- M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 R4700 ; configure sensor 0 as thermistor on pin bedtemp
- M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
- ; Heaters
- M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
- M143 H0 S100 ; set temperature limit for heater 0 to 120C
- M307 H0 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit
- M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
- M143 H1 S260 ; set temperature limit for heater 1 to 280C
- M307 H1 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit
- ; Fans
- M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
- M106 P0 C"Bauteilluefter" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off
- M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
- M106 P1 C"E3D Luefter" S1 H1 T45 ; set fan 1 name and value. Thermostatic control is turned on
- ; Tools
- M563 P0 S"Hotend" D0 H1 F0 ; define tool 0
- G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
- G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
- ; Manual bed levelling - Define the screw positions
- M671 X-5:300:300:-5 Y-10:-10:290:290 P0.5
- ; Pressure advance for BMG with bowden tube
- M572 D0 S0.30
- ; Custom settings are not defined
- ; Miscellaneous
- M501 ; load saved parameters from non-volatile memory
- T0 ; select first tool
Advertisement
Add Comment
Please, Sign In to add comment
