Helios4 Boot Output

BootROM - 1.73

Booting from MMC


General initialization - Version: 1.0.0
AVS selection from EFUSE disabled (Skip reading EFUSE values)
Overriding default AVS value to: 0x23
Detected Device ID 6828
High speed PHY - Version: 2.0

Init Customer board board SerDes lanes topology details:
 | Lane # | Speed|    Type     |
 ------------------------------|
 |   0    |  3   |  SATA0      |
 |   1    |  5   |  USB3 HOST0 |
 |   2    |  3   |  SATA1      |
 |   3    |  3   |  SATA3      |
 |   4    |  3   |  SATA2      |
 |   5    |  5   |  USB3 HOST1 |
 -------------------------------
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.46.0
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR Training Sequence - Start scrubbing
DDR Training Sequence - End scrubbing
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED

 __   __                      _ _
|  \/  | __ _ _ ____   _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| |  | | (_| | |   \ V /  __/ | |
|_|  |_|\__,_|_|    \_/ \___|_|_|
         _   _     ____              _
        | | | |   | __ )  ___   ___ | |_
        | | | |___|  _ \ / _ \ / _ \| __|
        | |_| |___| |_) | (_) | (_) | |_
         \___/    |____/ \___/ \___/ \__|
 ** LOADER **


U-Boot 2013.01 (Oct 09 2018 - 13:47:44) Marvell version: 2015_T1.0p16

Board: Helios4
SoC:   MV88F6828 Rev A0
       running 2 CPUs
CPU:   ARM Cortex A9 MPCore (Rev 1) LE
       CPU 0
       CPU    @ 1600 [MHz]
       L2     @ 800 [MHz]
       TClock @ 250 [MHz]
       DDR3    @ 800 [MHz]
       DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Enabled
DRAM:  2 GiB
MMC:   mv_sdh: 0
*** Warning - bad CRC, using default environment

USB2.0 0: Host Mode
USB3.0 0: Host Mode
USB3.0 1: Host Mode

Map:   Code:                    0x7fee6000:0x7ff978f0
       BSS:                     0x7ffef2fc
       Stack:                   0x7f9e3f20
       Heap:                    0x7f9e4000:0x7fee6000
       U-Boot Environment:      0x000fe000:0x00100000 (MMC)

Board configuration detected:
Net:
|  port  | Interface | PHY address  |
|--------|-----------|--------------|
| egiga0 |   RGMII   |     0x00     |
egiga0 [PRIME]
Hit any key to stop autoboot:  0
Trying to boot from MMC
1979 bytes read in 17 ms (113.3 KiB/s)
## Executing script at 03000000
Boot script loaded from mmc
173 bytes read in 13 ms (12.7 KiB/s)
19512 bytes read in 51 ms (373 KiB/s)
6238277 bytes read in 342 ms (17.4 MiB/s)
4822864 bytes read in 276 ms (16.7 MiB/s)
## Loading init Ramdisk from Legacy Image at 02880000 ...
   Image Name:   uInitrd
   Created:      2018-12-05  14:33:27 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    6238213 Bytes = 5.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
## Flattened Device Tree blob at 02040000
   Booting using the fdt blob at 0x02040000
   Using Device Tree in place at 02040000, end 02047c37

   Skipping Device Tree update ('fdt_skip_update' = yes)

Limit DDR size at 3GB due to power of 2 requirement of Address decoding

Starting kernel ...

Uncompressing Linux... done, booting the kernel.