Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 1.1.3 (Jan 18 2018 - 02:33:24)
- Board: Ralink APSoC DRAM: 64 MB
- relocate_code Pointer at: 83fb4000
- enable ephy clock...done. rf reg 29 = 5
- SSC disabled.
- spi_wait_nsec: 29
- spi device id: c8 40 17 c8 40 (4017c840)
- Warning: un-recognized chip ID, please update bootloader!
- ============================================
- Ralink UBoot Version: 5.0.0.0
- --------------------------------------------
- ASIC 7620_MP (Port5<->GigaSW)
- DRAM component: 512 Mbits DDR, width 16
- DRAM bus: 16 bit
- Total memory: 64 MBytes
- Flash component: SPI Flash
- Date:Jan 18 2018 Time:02:33:24
- ============================================
- icache: sets:512, ways:4, linesz:32 ,total:65536
- dcache: sets:256, ways:4, linesz:32 ,total:32768
- ##### The CPU freq = 580 MHZ ####
- estimate memory size =64 Mbytes
- rt_rtl8367_init(1705):Begin
- Wait for RTL8367C Ready
- .
- RTL8367C is ready now!
- rt_rtl8367_init(1749):Call Func rt_rtl8367_enableRgmii()
- continue to starting system. 0
- disable switch forward...
- 3: System Boot system code via Flash.(0xbc020000)
- do_bootm:argc=2, addr=0xbc020000
- ## Booting image at bc020000 ...
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80484090) ...
- ## Giving linux memsize in MB, 64
- Starting kernel ...
- LINUX started...
- THIS IS ASIC
- SDK 5.0.S.0
- Linux version 3.10.14 (root@e83ff11947af) (gcc version 4.6.3 (Buildroot 2012.11. 1) ) #1 Thu Jan 18 02:38:56 UTC 2018
- The CPU feqenuce set to 580 MHz
- PCIE: bypass PCIe DLL.
- PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
- disable all power about PCIe
- CPU0 revision is: 00019650 (MIPS 24KEc)
- Software DMA cache coherency
- Determined physical RAM map:
- memory: 04000000 @ 00000000 (usable)
- Initrd not found or empty - disabling initrd
- Zone ranges:
- Normal [mem 0x00000000-0x03ffffff]
- Movable zone start for each node
- Early memory node ranges
- node 0: [mem 0x00000000-0x03ffffff]
- Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
- Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- Kernel command line: console=ttyS1,115200n8 root=/dev/mtdblock2 rootfstype=squas hfs
- PID hash table entries: 256 (order: -2, 1024 bytes)
- Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- Writing ErrCtl register=0004f132
- Readback ErrCtl register=0004f132
- Memory: 58412k/65536k available (4663k kernel code, 7124k reserved, 1174k data, 304k init, 0k highmem)
- NR_IRQS:128
- console [ttyS1] enabled
- Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
- pid_max: default: 4096 minimum: 301
- Mount-cache hash table entries: 512
- ftrace: allocating 13655 entries in 27 pages
- NET: Registered protocol family 16
- RALINK_GPIOMODE = 1ab41d
- RALINK_GPIOMODE = 18b41d
- PPLL_CFG1=0xe6c000
- MT7620 PPLL lock
- PPLL_DRV =0x80080504
- start PCIe register access
- RALINK_RSTCTRL = 2400000
- RALINK_CLKCFG1 = 75afffc0
- *************** MT7620 PCIe RC mode *************
- PCIE0 enabled
- Port 0 N_FTS = 1b105000
- init_rt2880pci done
- bio: create slab <bio-0> at 0
- PCI host bridge to bus 0000:00
- pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
- pci_bus 0000:00: root bus resource [io 0x10160000-0x1016ffff]
- pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
- pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
- pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
- pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
- pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
- pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
- pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
- pci 0000:00:00.0: PCI bridge to [bus 01]
- pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
- pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
- BAR0 at slot 0 = 0
- bus=0x0, slot = 0x0
- res[0]->start = 0
- res[0]->end = 0
- res[1]->start = 20200000
- res[1]->end = 2020ffff
- res[2]->start = 0
- res[2]->end = 0
- res[3]->start = 0
- res[3]->end = 0
- res[4]->start = 0
- res[4]->end = 0
- res[5]->start = 0
- res[5]->end = 0
- bus=0x1, slot = 0x0
- res[0]->start = 20000000
- res[0]->end = 200fffff
- res[1]->start = 0
- res[1]->end = 0
- res[2]->start = 0
- res[2]->end = 0
- res[3]->start = 0
- res[3]->end = 0
- res[4]->start = 0
- res[4]->end = 0
- res[5]->start = 0
- res[5]->end = 0
- Switching to clocksource MIPS
- NET: Registered protocol family 2
- TCP established hash table entries: 512 (order: 0, 4096 bytes)
- TCP bind hash table entries: 512 (order: -1, 2048 bytes)
- TCP: Hash tables configured (established 512 bind 512)
- TCP: reno registered
- UDP hash table entries: 256 (order: 0, 4096 bytes)
- UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- NET: Registered protocol family 1
- Load Ralink Timer0 Module
- Load Ralink Timer1 Module
- MTK/Ralink EHCI/OHCI init.
- squashfs: version 4.0 (2009/01/31) Phillip Lougher
- NTFS driver 2.1.30 [Flags: R/W].
- fuse init (API version 7.22)
- msgmni has been set to 114
- io scheduler noop registered (default)
- Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
- serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
- serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
- Ralink gpio driver initialized
- brd: module loaded
- deice id : c8 40 17 c8 40 (4017c840)
- Warning: un-recognized chip ID, please update SPI driver!
- GD25Q64B(c8 40170000) (8192 Kbytes)
- mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numera seregions = 0
- Creating 7 MTD partitions on "raspi":
- 0x000000000000-0x000000020000 : "boot"
- 0x000000020000-0x000000220000 : "kernel"
- 0x000000220000-0x0000007c0000 : "rootfs"
- mtd: partition "rootfs" set to be root filesystem
- 0x0000007c0000-0x0000007d0000 : "config"
- 0x0000007d0000-0x0000007e0000 : "romfile"
- 0x0000007e0000-0x0000007f0000 : "ispconfig"
- 0x0000007f0000-0x000000800000 : "radio"
- Register flash device:flash0
- PPP generic driver version 2.4.2
- PPP MPPE Compression module registered
- NET: Registered protocol family 24
- register rt2860
- <-- RTMPAllocTxRxRingMemory, Status=0
- <-- RTMPAllocAdapterBlock, Status=0
- device_id =0x7662
- ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCt rl=0x20a
- RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
- NVM is FLASH mode (pAd->flash_offset = 0x7f8000)
- get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
- rdm_major = 253
- spiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6
- Read MAC from flash( 7df100) ffffffac-ffffff84-ffffffc6-65-02-ffffffce
- netif_napi_add() called with weight 128 on device eth0
- SMACCR1 -- : 0x0000ac84
- SMACCR0 -- : 0xc66502ce
- Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocate d, mtu = 1500!
- NAPI enable, Tx Ring = 512, Rx Ring = 512
- spiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6
- Read MAC from flash( 7df100) ffffffac-ffffff84-ffffffc6-65-02-ffffffce
- SMACCR1 -- : 0x0000ac84
- SMACCR0 -- : 0xc66502ce
- PROC INIT OK!
- Mirror/redirect action on
- u32 classifier
- Performance counters on
- input device check on
- Actions configured
- Netfilter messages via NETLINK v0.30.
- nf_conntrack version 0.5.0 (912 buckets, 3648 max)
- gre: GRE over IPv4 demultiplexor driver
- ip_tables: (C) 2000-2006 Netfilter Core Team
- Type=Linux
- TCP: cubic registered
- NET: Registered protocol family 10
- ip6_tables: (C) 2000-2006 Netfilter Core Team
- sit: IPv6 over IPv4 tunneling driver
- NET: Registered protocol family 17
- Ebtables v2.0 registered
- 8021q: 802.1Q VLAN Support v1.8
- registered taskstats version 1
- VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- Freeing unused kernel memory: 304K (805b4000 - 80600000)
- starting pid 713, tty '': '/etc/init.d/rcS'
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- ehci-platform: EHCI generic platform driver
- ehci-platform ehci-platform: EHCI Host Controller
- ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
- ehci-platform ehci-platform: irq 18, io mem 0x101c0000
- ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- ohci-platform ohci-platform: Generic Platform OHCI Controller
- ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
- ohci-platform ohci-platform: irq 18, io mem 0x101c1000
- hub 2-0:1.0: USB hub found
- hub 2-0:1.0: 1 port detected
- usbcore: registered new interface driver usb-storage
- tp_domain init ok
- PPTP driver version 0.8.5
- l2tp_core: L2TP core driver, V2.0
- l2tp_ppp: PPPoL2TP kernel driver, V2.0
- Please press Enter to activate this console. [ ipt_init ] cmd: /var/tmp/dconf/rc .router
- [ dm_readFile ] 2193: can not open xml file /var/tmp/pc/reduced_data_model.xml! , about to open file /etc/reduced_data_model.xml
- spiflash_ioctl_read, Read from 0x007c0000 length 0x10000, ret 0, retlen 0x10000
- spiflash_ioctl_read, Read from 0x007c0000 length 0x944f, ret 0, retlen 0x944f
- ===>Enter routerspiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, ret len 0x6
- mode
- spiflash_ioctl_read, Read from 0x007df500 length 0x29, ret 0, retlen 0x29
- spiflash_ioctl_read, Read from 0x007df600 length 0x21, ret 0, retlen 0x21
- spiflash_ioctl_read, Read from 0x007df700 length 0x10, ret 0, retlen 0x10
- spiflash_ioctl_read, Read from 0x007df200 length 0x4, ret 0, retlen 0x4
- spiflash_ioctl_read, Read from 0x00020000 length 0x20c, ret 0, retlen 0x20c
- [ rsl_initDevInfo ] cmd: echo 0 > /proc/tplink/mspiflash_ioctl_read, Read from 0 x007df100 length 0x6, ret 0, retlen 0x6
- anufacture_flag
- [ rsl_getManagementServerObj ] 492: cannot set connectionRequestURL yet because no WAN intf is up
- [ rsl_getManagementServerObj ] 492: cannot set connectionRequestURL yet because no WAN intf is up
- [ rsl_getManagementServerObj ] 492: cannot set connectionRequestURL yet because no WAN intf is up
- [ tr143_main ] 162: 909 start select, maxFd: 7, msgFd.fd: 5, compFd: 7
- [ oal_startDynDns ] cmd: dyndns /var/tmp/dconf/dyndns.conf
- [ oal_startNoipDns ] cmd: noipdns /var/tmp/dconf/noipdns.conf
- [ oal_vlan_fetchState ] 351: Failed to read VLAN file.
- ioctl: No such device
- [ oal_br_addBridge ] cmd: brctl addbr br0
- [ oal_br_addBridge ] cmd: brctl setfd br0 0
- [ oal_br_addBridge ] cmd: brctl stp br0 off
- [ oal_ipt_addLanRules ] cmd: iptables -t filter -A INPUT -i br+ -j ACCEPT
- [ oal_intf_setIntf ] cmd: ifconfig br0 192.168.0use br_hw_addr!
- .1 netmask 255.255.255.0 up
- [ oal_util_setProcLanAddr ] cmd: echo "br0 16820416," > /proc/net/c 0: 0: C:4C: 5:FFFFFF80
- onntract_LocalAdRaeth v3.1 (dr
- [ oal_intf_eNAPI
- nableIntf ] cmd:,SkbRecycle ifconfig eth0 u)
- p
- phy_tx_ring = 0x02d36000, tx_ring = 0xa2d36000
- phy_rx_ring0 = 0x02d38000, rx_ring0 = 0xa2d38000
- RTL8367C is ready now!
- SMACCR1 -- : 0x0000ac84
- SMACCR0 -- : 0xc66502ce
- ESW: Link Status Changed - Port5 Link UP
- CDMA_CSG_CFG = 81000000
- GDMA1_FWD_CFG = 20710000
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
- ifconfig: ioctl 0x8913 failed: No such device
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.4 up
- ifconfig: ioctl 0x8913 failed: No such device
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.5 up
- ifconfig: ioctl 0x8913 failed: No such device
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.6 up
- ifconfig: ioctl 0x8913 failed: No such device
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
- [ oal_addVlanTagIntf ] cmd: vconfig add eth0 3
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
- set if eth0.3 to *not wan dev
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
- [ oal_addVlanTagIntf ] cmd: vconfig add eth0 4
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.4 up
- set if eth0.4 to *not wan dev
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
- [ oal_addVlanTagIntf ] cmd: vconfig add eth0 5
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.5 up
- set if eth0.5 to *not wan dev
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
- [ oal_addVlanTagIntf ] cmd: vconfig add eth0 6
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.6 up
- set if eth0.6 to *not wan dev
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
- [ oal_addVlanTagIntf ] cmd: vconfig add eth0 2
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.2 up
- set if eth0.2 to wan dev
- [ oal_br_delIntfFromBridge ] cmd: brctl delif br0 eth0.3
- brctl: bridge br0: Invalid argument
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
- [ oal_device eth0.3 entered promiscuous mode
- br_addIntfIntoBrdevice eth0 entered promiscuous mode
- idge ] cmd: brctbr0: port 1(eth0.3) entered forwarding state
- l addif br0 eth0br0: port 1(eth0.3) entered forwarding state
- .3
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
- [ oal_br_delIntfFromBridge ] cmd: brctl delif br0 eth0.4
- brctl: bridge br0: Invalid argument
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.4 up
- device eth0.4 entered promiscuous mode
- [ oal_br_addIntfbr0: port 2(eth0.4) entered forwarding state
- IntoBridge ] cmdbr0: port 2(eth0.4) entered forwarding state
- : brctl addif br0 eth0.4
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
- [ rsl_getUnusedVlan ] 1153: br0: port 2(eth0.4) entered disabled state
- GET UNUSED VLAN TAG 2 : [4]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
- [ oal_br_delIntfFromBridge ] cmd: brctl delif br0 eth0.5
- brctl: bridge br0: Invalid argument
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.5 up
- device eth0.5 entered promiscuous mode
- [ oal_br_addIntfbr0: port 3(eth0.5) entered forwarding state
- IntoBridge ] cmdbr0: port 3(eth0.5) entered forwarding state
- : brctl addif br0 eth0.5
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
- [ br0: port 3(eth0.5) entered disabled state
- rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
- [ oal_br_delIntfFromBridge ] cmd: brctl delif br0 eth0.6
- brctl: bridge br0: Invalid argument
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.6 up
- device eth0.6 entered promiscuous mode
- [ oal_br_addIntfbr0: port 4(eth0.6) entered forwarding state
- IntoBridge ] cmdbr0: port 4(eth0.6) entered forwarding state
- : brctl addif br0 eth0.6
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3br0: port 4(eth0.6) entered di sabled state
- : [5]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
- [ oal_eth_setIGMPSnoopParam ] cmd: sh /etc/igmp/igmp_snoop.sh 1
- [ oal_eth_setIGMPSnoopParam ] cmd: echo 1 > /proc/tplink/eth_igmp_snooping
- [ oal_wlan_ra_setCountryRegion ] cmd: cp /etc/SingleSKU.dat /var/Wireless/RT2860 AP/SingleSKU.dat
- [ oal_wlan_ra_setCountryRegion ] cmd: iwpriv ra0 set CountryRegion=1
- ra0 no private ioctls.
- [ oal_wlan_ra_loadDriver ] cmd: insmod /lib/modules/kmdir/kernel/drivers/net/wir eless/rt2860v2_ap/rt2860v2_ap.ko
- [ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig apcli0 down
- ifconfig: ioctl 0x8913 failed: No such device
- [ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig ra1 down
- ifconfig: ioctl 0x8913 failed: No such device
- [ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig ra2 down
- ifconfig: ioctl 0x8913 failed: No such device
- [ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig ra3 down
- ifconfig: ioctl 0x8913 failed: No such device
- [ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig ra4 down
- ifconfig: ioctl 0x8913 failed: No such device
- [ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig ra0 down
- [ oal_wlan_ra_openVap ] cmd: ifconfig ra0 up
- start ch = 1, ch->num = 2
- 28 28 28 28
- 28 28 28 28 28 28 28 28
- 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28
- 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- start ch = 3, ch->num = 9
- 28 28 28 28
- 28 28 28 28 28 28 28 28
- 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28
- 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28
- start ch = 12, ch->num = 2
- 28 28 28 28
- 28 28 28 28 28 28 28 28
- 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28
- 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- start ch = 14, ch->num = 1
- 28 28 28 28
- 0 0 0 0 0 0 0 0
- 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- exec!
- spiflash_ioctl_read, Read from 0x007f0000 length 0x200, ret 0, retlen 0x200
- eeFlashId = 0x7620!
- open DNS error: No such file or directory
- [ oal_sys_getOldTZInfo ] 462: Open TZ file error!
- [ oal_sys_unsetTZ ] cmd: echo "" > /etc/TZ
- [ oal_sys_unsetTZ ] cmd: echo "" > /etc/TZ
- 0x1300 = 00064320
- [ oal_wlan_ra_openVap ] cmd: killall -q wscd
- [ oal_wlan_ra_openVap ] cmd: wscd -i ra0 -m 1 -w /var/tmp/wsc_upnp/ &
- [ oal_wlan_controlWlanLed ] cmd: echo "1" > /proc/tplink/led_wlan_24G
- [ oal_wlan_ra_initWlan ] cmd: ifconfig ra0 up
- [ oal_wlan_controlWlanLed ] cmd: echo "1" > /proc/tplink/led_wlan_24G
- [ oal_br_device ra0 entered promiscuous mode
- addIntfIntoBridgbr0: port 5(ra0) entered forwarding state
- e ] cmd: brctl abr0: port 5(ra0) entered forwarding state
- ddif br0 ra0
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
- wscd: SSDP UDP PORT = 1900
- [ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice apcli0 entered promiscuous mode
- 0 apcli0
- [ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice ra2 entered promiscuous mode
- 0 ra2
- [ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice ra3 entered promiscuous mode
- 0 ra3
- [ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice ra4 entered promiscuous mode
- 0 ra4
- [ wlan_handleL2Desc ] 2401: br0
- [ oal_br_addIndevice ra1 entered promiscuous mode
- tfIntoBridge ] cmd: brctl addif br0 ra1
- [ oal_wlan_ra_initEnd ] cmd: wlNspiflash_ioctl_read, Read from 0x007f0000 length 0x2, ret 0, retlen 0x2
- etlinkTool &
- [ oal_wlan_ra_initEnd ] cmd: killall -q wscd
- [ oal_wlan_ra_initEnd ] cmd: wscd -i ra0 -m 1 -w /var/tmp/wsc_upnp/ &
- WLAN-Start wlNetlinkTool
- Waiting for Wireless Events from interfaces...
- swWlanChkAhbErr: netlink to do
- wscd: SSDP UDP PORT = 1900
- [ oal_wlan_ra_setCountryRegion ] cmd: cp /etc/SingleSKU_5G.dat /var/Wireless/RT2860AP/SingleSKU_5G.dat
- [ oal_wlan_ra_setCountryRegion ] cmd: iwpriv rai0 set CountryRegionABand=1
- Interface doesn't accept private ioctl...
- set (8BE2): Network is down
- [ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig apclii0 down
- ifconfig: ioctl 0x8913 failed: No such device
- [ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig rai1 down
- ifconfig: ioctl 0x8913 failed: No such device
- [ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig rai2 down
- ifconfig: ioctl 0x8913 failed: No such device
- [ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig rai3 down
- ifconfig: ioctl 0x8913 failed: No such device
- [ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig rai4 down
- ifconfig: ioctl 0x8913 failed: No such device
- [ oal_wlan_ra_WriteWlanCfgFile ] cmd: ifconfig rai0 down
- [ oal_wlan_ra_openVap ] cmd: ifconfig rai0 up
- build time =
- 20141115060606a
- rom patch for E3 IC
- platform =
- ALPS
- hw/sw version =
- ▒▒
- patch version =
- FW Version:0.0.00 Build:1
- Build Time:201507311614____
- fw for E3 IC
- spiflash_ioctl_read, Read from 0x007f8000 length 0x200, ret 0, retlen 0x200
- ==============eeFlashId: 30306 ====================
- RX[0] DESC a3438000 size = 4096
- RX[1] DESC a3439000 size = 4096
- E2pAccessMode=2
- cfg_mode=14
- cfg_mode=14
- APSDCapable[0]=0
- APSDCapable[1]=0
- APSDCapable[2]=0
- APSDCapable[3]=0
- APSDCapable[4]=0
- APSDCapable[5]=0
- APSDCapable[6]=0
- APSDCapable[7]=0
- APSDCapable[8]=0
- APSDCapable[9]=0
- APSDCapable[10]=0
- APSDCapable[11]=0
- APSDCapable[12]=0
- APSDCapable[13]=0
- APSDCapable[14]=0
- APSDCapable[15]=0
- default ApCliAPSDCapable[0]=0
- pAd->ed_threshold = 90
- pAd->ed_chk = 0
- pAd->ed_false_cca_threshold = 250
- Key1Str is Invalid key length(0) or Type(0)
- Key1Str is Invalid key length(0) or Type(0)
- Key1Str is Invalid key length(0) or Type(0)
- Key1Str is Invalid key length(0) or Type(0)
- Key2Str is Invalid key length(0) or Type(0)
- Key2Str is Invalid key length(0) or Type(0)
- Key2Str is Invalid key length(0) or Type(0)
- Key2Str is Invalid key length(0) or Type(0)
- Key3Str is Invalid key length(0) or Type(0)
- Key3Str is Invalid key length(0) or Type(0)
- Key3Str is Invalid key length(0) or Type(0)
- Key3Str is Invalid key length(0) or Type(0)
- Key4Str is Invalid key length(0) or Type(0)
- Key4Str is Invalid key length(0) or Type(0)
- Key4Str is Invalid key length(0) or Type(0)
- Key4Str is Invalid key length(0) or Type(0)
- APCli_WPAPSK_KEY, key string required 8 ~ 64 characters!!!
- I/F(apcli0) Key1Str is Invalid key length!
- I/F(apcli0) Key2Str is Invalid key length!
- I/F(apcli0) Key3Str is Invalid key length!
- I/F(apcli0) Key4Str is Invalid key length!
- 1. Phy Mode = 49
- spiflash_ioctl_read, Read from 0x007f8000 length 0x200, ret 0, retlen 0x200
- ==============eeFlashId: 30306 ====================
- get_chl_grp:illegal channel (167)
- get_chl_grp:illegal channel (167)
- get_chl_grp:illegal channel (169)
- get_chl_grp:illegal channel (169)
- get_chl_grp:illegal channel (171)
- get_chl_grp:illegal channel (171)
- Country Region from e2p = ffff
- mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=1, temp_tx_alc_enable=1
- mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=1
- mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=15, low_temp_slope=9
- mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0
- mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4
- mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0
- mt76x2_get_external_lna_gain::LNA type=0x1, BLNAGain=0xffffff8c, ALNAGain0=0xffffff8c, ALNAGain1=0xffffff8c, ALNAGain2=0xffffff8c
- 2. Phy Mode = 49
- 3. Phy Mode = 49
- andes_pci_fw_init
- 0x1300 = 00073200
- AntCfgInit: primary/secondary ant 0/1
- andes_load_cr:cr_type(2)
- ChipStructAssign(): MT76x2 hook !
- MCS Set = ff ff 00 00 01
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- mt76x2_single_sku::sku_base_pwr = 0x22, DefaultTargetPwr = 0x22, ch_pwr_adj = 0x0(0), 0x13B4: 0x1b0f0400
- APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
- ap_ftkd> Initialize FT KDP Module...
- @@@ ed_monitor_init : ===>
- @@@ ed_monitor_init : <===
- Main bssid = ac:84:c6:65:02:d0
- mt76x2_reinit_agc_gain:original agc_vga0 = 0x48, agc_vga1 = 0x48
- mt76x2_reinit_agc_gain:updated agc_vga0 = 0x48, agc_vga1 = 0x48
- mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x33, hi_lna1 = 0x33
- mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x33, hi_lna1 = 0x33
- <==== rt28xx_init, Status=0
- get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
- get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
- get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
- get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
- get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=apclii
- RTMPDrvOpen(1):Check if PDMA is idle!
- RTMPDrvOpen(2):Check if PDMA is idle!
- @@@ ed_monitor_init : ===>
- @@@ ed_monitor_init : <===
- [ oal_wlan_ra_openVap ] cmd: killall -q wscd_5G
- [ oal_wlan_ra_openVap ] cmd: wscd_5G -i rai0 -m 1 -w /var/tmp/wsc_upnp_5G/ &
- [ oal_wlan_controlWlanLed ] cmd: echo "1" > /proc/tplink/led_wlan_5G
- [ oal_wlan_ra_WriteWlanCfgFile ] cmd: iwpriv rai0 set ed_chk=1
- wscd: SSDP UDP PORT = 1900
- @@@ ed_monitor_init : ===>
- @@@ ed_monitor_init : <===
- [ oal_wlan_ra_initWlan ] cmd: ifconfig rai0 up
- [ oal_wlan_controlWlanLed ] cmd: echo "1" > /proc/tplink/led_wladevice rai0 entered promiscuous mode
- n_5G
- [ oal_br_abr0: port 11(rai0) entered forwarding state
- ddIntfIntoBridgebr0: port 11(rai0) entered forwarding state
- ] cmd: brctl addif br0 rai0
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
- [ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice apclii0 entered promiscuous mode
- 0 apclii0
- [ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice rai2 entered promiscuous mode
- 0 rai2
- [ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice rai3 entered promiscuous mode
- 0 rai3
- [ oal_br_addIntfIntoBridge ] cmd: brctl addif brdevice rai4 entered promiscuous mode
- 0 rai4
- [ wlan_handleL2Desc ] 2401: br0
- [ oal_br_addIndevice rai1 entered promiscuous mode
- tfIntoBridge ] cmd: brctl addif br0 rai1
- wlNetlinkTool isspiflash_ioctl_read, Read from 0x007f8000 length 0x2, ret 0, retlen 0x2
- already there.
- [ oal_wlan_ra_initEnd ] cmd: killall -q wscd_5G
- [ oal_wlan_ra_initEnd ] cmd: wscd_5G -i rai0 -m 1 -w /var/tmp/wsc_upnp_5G/ &
- wscd: SSDP UDP PORT = 1900
- [ oal_startUPnP ] cmd: upnpd -L br0 -W eth0.2 -en 1 -nat 0 -port 80 -url "http://www.tp-link.com" -ma "TP-Link" -mn "Archer_C5" -mv "4.0" -desc "AC1200 Wireless Dual Band Gigabit Router " &
- sendto: No such file or directory
- pid 786 send 2004 error
- [ oal_ovpn_createDir ] cmd: mkdir /var/openvpn
- [ oal_ovpn_createDir ] cmd: chmod 777 /var/openvpn
- [ oal_ovpn_setupTunMod ] cmd: insmod /lib/modules/kmdir/kernel/drivers/net/tun.ko
- tun: Universal TUN/TAP device driver, 1.6
- tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- [ oal_pvpn_setupNeededMod ] cmd: insmod /lib/modules/kmdir/kernel/drivers/net/ppp_mppe.ko
- insmod: can't insert '/lib/modules/kmdir/kernel/drivers/net/ppp_mppe.ko': No such file or directory
- [ oal_startDhcps ] cmd: dhcpd /var/tmp/dconf/udhcpd.conf
- sh: can't create /proc/sys/kernel/core_pattern: nonexistent directory
- [ oal_lan6_startRadvd ] cmd: radvd -C /var/tmp/dconf/radvd_br0.conf -p /var/run/radvd_br0.pid &
- [ oal_snmp_updateCfg ] cmd: iptables -t filter -D ACL -p udp --dport 161 -j ACCEPT
- iptables: Bad rule (does a matching rule exist in that chain?).
- iptables: Bad rule (does a matching rule exist in that chain?).
- [ oal_startSnmp ] cmd: snmpd -f /var/tmp/dconf/snmpd.conf
- radvd starting
- [ oal_br_delIntfFromBridge ] cmd: brctl delif br0 eth0.2
- brctl: bridge br0: Invalid argument
- [ oal_br_delIntfFromBridge ] cmd: brctl delif br0 eth0.2
- brctl: bridge br0: Invalid argument
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
- [ util_enFuncQueue ] 099: Function queue not support RDP_OPT_ADD_OBJ operation
- [ util_enFuncQueue ] 099: Function queue not support RDP_OPT_ADD_OBJ operation
- set eth status, stack = 2 [1 1 0 0 0 0]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 1 : [3]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 2 : [4]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 3 : [5]
- [ rsl_getUnusedVlan ] 1153: GET UNUSED VLAN TAG 4 : [6]
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.3 up
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.4 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.5 down
- [ oal_intf_disableIntf ] cmd: ifconfig eth0.6 down
- [ oal_intf_setIfMac ] cmd: ifconfig eth0.2 down
- [ oal_intf_setIfMac ] cmd: ifconfig eth0.2 hw ether AC:84:C6:65:02:CF up
- [ oal_intf_enableIntf ] cmd: ifconfig eth0.2 up
- [ oal_ipt_setDDoSRules ] cmd: iptables -F FIREWALL_DDOS
- [ ddos_clearAll ] cmd: rm -f /var/tmp/dosHost
- [ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_ftp.ko
- [ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_ftp.ko
- [ oal_openAlg ] cmd: iptables -D FORWARD_VPN_PASSTHROUGH -p udp --dport 500 -j DROP
- iptables: Bad rule (does a matching rule exist in that chain?).
- [ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_proto_gre.ko
- insmod: can't insert '/lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_proto_gre.ko': File exists
- [ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko
- [ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_pptp.ko
- insmod: can't insert '/lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_pptp.ko': File exists
- [ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_pptp.ko
- [ oal_openAlg ] cmd: iptables -D FORWARD_VPN_PASSTHROUGH -p tcp --dport 1723 -j DROP
- iptables: Bad rule (does a matching rule exist in that chain?).
- [ oal_openAlg ] cmd: iptables -D FORWARD_VPN_PASSTHROUGH -p udp --dport 1701 -j DROP
- iptables: Bad rule (does a matching rule exist in that chain?).
- [ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_tftp.ko
- [ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_tftp.ko
- [ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_h323.ko
- [ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_h323.ko
- [ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_sip.ko
- [ setupModules ] cmd: insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_sip.ko
- [ oal_Ralink HW NAT Module Enabled
- wan_HWNat_enable ] cmd: insmod /lib/modules/kmdir/kernel/net/nat/hw_nat/hw_nat.ko
- [ oal_initIp6FirewallObj ] cmd: ip6tables -F
- [ oal_initIp6FirewallObj ] cmd: ip6tables -X
- [ oal_initIp6FirewallObj ] cmd: ip6tables -P INPUT DROP
- [ oal_initIp6FirewallObj ] cmd: ip6tables -P FORWARD DROP
- [ oal_initIp6FirewallObj ] cmd: ip6tables -P OUTPUT ACCEPT
- [ oal_initIp6FirewallObj ] cmd: ip6tables -N ACLV6
- [ oal_initIp6FirewallObj ] cmd: ip6tables -N FIREWALL
- [ oal_initIp6FirewallObj ] cmd: ip6tables -N FWRULE
- [ oal_initIp6FirewallObj ] cmd: ip6tables -N INPUT_FIREWALL
- [ oal_initIp6FirewallObj ] cmd: ip6tables -N INPUT_FWRULE
- [ oal_initIp6FirewallObj ] cmd: ip6tables -N PARENTCTL
- [ oal_initIp6FirewallObj ] cmd: ip6tables -N PCRULE
- [ oal_initIp6FirewallObj ] cmd: ip6tables -N PCDROP
- [ oal_initIp6FirewallObj ] cmd: ip6tables -N INPUT_PARENTCTL
- [ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -i lo -p ALL -j ACCEPT -m comment --comment "loop back"
- [ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT
- [ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -j ACLV6
- [ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -p icmpv6 ! --icmpv6-type echo-request -j ACCEPT
- [ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -p udp ! -i br+ --sport 547 --dport 546 -j ACCEPT
- [ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -p udp -i br+ --sport 546 --dport 547 -j ACCEPT
- [ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -p udp --sport 521 --dport 521 -j ACCEPT
- [ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -j INPUT_PARENTCTL
- [ oal_initIp6FirewallObj ] cmd: ip6tables -A INPUT -j INPUT_FIREWALL
- [ oal_initIp6FirewallObj ] cmd: ip6tables -A FORWARD -o br+ -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT
- [ oal_initIp6FirewallObj ] cmd: ip6tables -A FORWARD -j PARENTCTL
- [ oal_initIp6FirewallObj ] cmd: ip6tables -A FORWARD -j FIREWALL
- [ oal_initIp6FirewallObj ] cmd: ip6tables -A FORWARD -i br+ -j ACCEPT
- [ oal_ipt6_setLanHttpPort ] cmd: ip6tables -A INPUT -i br+ -p tcp --dport 80 -j ACCEPT
- [ oal_fw6_setFwEnabeld ] cmd: ip6tables -D FIREWALL -j ACCEPT
- ip6tables: Bad rule (does a matching rule exist in that chain?).
- [ oal_fw6_setFwEnabeld ] cmd: ip6tables -F FIREWALL
- [ oal_fw6_setSpiFirewall ] cmd: ip6tables -t filter -D FORWARD ! -i br+ -m conntrack --ctstate NEW -j ACCEPT
- ip6tables: Bad rule (does a matching rule exist in that chain?).
- [ oal_initFirewallObj ] cmd: ebtables -N FIREWALL
- [ oal_fw_setSpiFirewall ] cmd: iptables -t filter -D FORWARD ! -i br+ -m conntrack --ctstate NEW -j ACCEPT
- iptables: Bad rule (does a matching rule exist in that chain?).
- [ rsl_setStorageServiceObj ] 1394: mountFlag is 3,We start usb server
- [ oal_killDlnaMediaSeverProcess ] cmd: killall ushare
- killall: ushare: no process killed
- uShare (version 1.1a), a lightweight UPnP A/V and DLNA Media Server.
- Benjamin Zores (C) 2005-2007, for GeeXboX Team.
- See http://ushare.geexbox.org/ for updates.
- [ oal_ipt_setWanPort ] cmd: iptables -t filter -D INPUT -p tcp --dport 21 -j ACCEPT
- iptables: Bad rule (does a matching rule exist in that chain?).
- [ oal_ipt_setWanPort ] cmd: iptables -t nat -D PREROUTING -p tcp --dport 21 -j ACCEPT
- iptables: Bad rule (does a matching rule exist in that chain?).
- [ oal_ipt_setWanPort ] cmd: ip6tables -t filter -D ACLV6 -p tcp --dport 21 -j ACCEPT
- ip6tables: Bad rule (does a matching rule exist in that chain?).
- [ oal_ipt_setAclRules ] cmd: iptables -t filter -A ACL -i br+ -p icmp -j ACCEPT
- [ oal_ipt_setAclRules ] cmd: ip6tables -t filter -A ACLV6 -i br+ -p icmpv6 --icmpv6-type echo-request -j ACCEPT
- [ oal_sys_enablePowerLed ] cmd: echo 1 > /proc/tplink/led_sys
- [ cos_init ] cmd: echo 3 > /proc/sys/vm/drop_caches
- Found 0 files and subdirectories.
- open DNS error: No such file or directory
- [ oal_sys_unsetTZ ] cmd: echo "" > /etc/TZ
- [ oal_sys_unsetTZ ] cmd: echo "" > /etc/TZ
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement