RDA8810 Boot_ROM V1.6
HW_CFG: 4286
SW_CFG: 0000
Load EMMC
Open eMMC
EMMC OCR timeout
Open eMMC card Failed
Load EMMC Fail
Load SD
Open SD card
mcd_Open
Card is NOT V2
Inserted Card is a SD card
mcd_Open Done
Loading image from SD card ................................................................................................Done
Check Image ... Done
Run ...
Init Clock ...
Clock config ver: 1.0
PMU vbuck1 = 9, vbuck3 = 10
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1
setup ddr vtt to 1


rda2 stand for dqs_prsel_preset
rda2=0 rda2=1 rda2=2 rda2=3 rda2=4 rda2=5 rda2=6 rda2=7
   R      R      R      R      *      *      R      R
Please check the result and choose the best one
 final rda2= 0, rda2_old = 2
setup ddr vtt to 1
pll freq CPU = 988
pll freq BUS = 800
pll freq MEM = 260
Init DDR, flag = 0x0002, para = 0x00001338
32bit dll-on Mode ...
ddr2 phy init done!
format ctrl value: 22000202
address ctrl value: 30301
decode ctrl value: 10
dram init done ...
Done
SETTING SECURITY CONTEXT
Board security: Not present
Init emmc ...
MMC: registered mmc interface 0
Spl init emmc first, use default zero mclk adj and inv.
MMC: registered mmc interface 1
raise: Signal # 8 caught
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x0010f948
-------------MMC information-----------
Manufacturer ID: 89,  Name: Unknown
OEM: 503
Tran Speed: 25000000
Rd Block Len: 512
SD version 2.0
High Capacity: No
Capacity: Bus Width: 4-bit
-----------------------------------------
boot_mmc mfr id = 89
EMMC boot ...
Check Image ...Verify image:
 Done


U-Boot 2012.04.442-rel5.0.2 (Apr 23 2017 - 17:38:39)

RDA8810 SoC
Board: RDA8810
DRAM:  236 MiB
CPU: enable instruction caches
CPU: enable data caches
CPU: enable neon
CPU:   p15-c1-c1 (NSACR): 0x00000000 -> 0x00000c00
CPU:   p15-c1-c0 (CPACR): 0x00000000 -> 0x00f00000
NAND:  metal 28 hwcfg 4286, use eMMC, skip nand init
0 MiB
MMC:   MMC: registered mmc interface 0
Cannot find the emmc corresponding mclk adj and inv.Now use default zero. Please add it
MMC: registered mmc interface 1
  response timeout
  response timeout
  response timeout
Card did not respond to voltage select!
-------------MMC information-----------
Manufacturer ID: 0,  Name: Unknown
OEM: 0
Tran Speed: 0
Rd Block Len: 0
MMC version 0.0
High Capacity: No
Capacity: Bus Width: 1-bit
-----------------------------------------
  response timeout
  response timeout
  response timeout
  response timeout
  response timeout
  response timeout
  response timeout
-------------MMC information-----------
Manufacturer ID: 89,  Name: Unknown
OEM: 503
Tran Speed: 0
Rd Block Len: 0
MMC version 0.0
High Capacity: No
Capacity: Bus Width: 1-bit
-----------------------------------------
mmc_parts_init: fastboot device mmc0 not found
MMC: 0, MMC: 1
Using default environment

In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0
Board Mux : Done.
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x8dae6988
-------------MMC information-----------
Manufacturer ID: 89,  Name: Unknown
OEM: 503
Tran Speed: 25000000
Rd Block Len: 512
SD version 2.0
High Capacity: No
Capacity: Bus Width: 4-bit
-----------------------------------------
mmc0 is current device
Loading file "boot.scr" from mmc device 0:1 (xxa1)
976 bytes read
## Executing script at 81000000
** No boot file defined **
Loading file "uInitrd" from mmc device 0:1 (xxa1)
3091319 bytes read
Loading file "zImage" from mmc device 0:1 (xxa1)
3396584 bytes read
Loading file "modem.bin" from mmc device 0:1 (xxa1)
2097152 bytes read

## Checking Modem Code Image at 80000000 ...
   Verifying Image Header ... OK
   Image Name:   Modem raminit codes
   Image Type:   MIPS Linux Kernel Image (uncompressed)
   Data Size:    2064 Bytes = 2 KiB
   Load Address: 01c16000
   Entry Point:  81c16000
   Verifying Data Checksum ... OK
## Raminit Image Detected

## Checking Modem Code Image at 80000850 ...
   Verifying Image Header ... OK
   Image Name:   Modem work codes
   Image Type:   MIPS Linux Kernel Image (uncompressed)
   Data Size:    2003744 Bytes = 1.9 MiB
   Load Address: 02000800
   Entry Point:  82000800
   Verifying Data Checksum ... OK
## Work Image Detected
## Set modem logic base address 0x2000000

## Init mdcom ports ... Done

## Load Raminit Code to modem at 01c16000 (AP address 11c16000) ...
    pc = 81c16000
    param = 00000000
Done

## Start modem and waiting for response ... Done

## Load Work Code to modem at 02000800 (AP address 12000800) ...
    pc = 82000800
    param = 00000000
Done

## Load Calib Data to modem at Load factory from flash ...