Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- 04040C0F][04040C0D]
- DDR Calibration DQS reg = 00008889
- U-Boot 1.1.3 (Apr 15 2019 - 17:56:43)
- Board: Ralink APSoC DRAM: 64 MB
- relocate_code Pointer at: 83fb8000
- ******************************
- Software System Reset Occurred
- ******************************
- gpiomode2 05540554.
- gpiomode2 00000000.
- gpiomode2 05550555.
- flash manufacture id: c8, device id 40 17
- find flash: GD25Q64B
- ============================================
- Ralink UBoot Version: 4.3.0.0
- --------------------------------------------
- ASIC 7628_MP (Port5<->None)
- DRAM component: 512 Mbits DDR, width 16
- DRAM bus: 16 bit
- Total memory: 64 MBytes
- Flash component: SPI Flash
- Date:Apr 15 2019 Time:17:56:43
- ============================================
- icache: sets:512, ways:4, linesz:32 ,total:65536
- dcache: sets:256, ways:4, linesz:32 ,total:32768
- ##### The CPU freq = 580 MHZ ####
- estimate memory size =64 Mbytes
- RESET MT7628 PHY!!!!!!
- continue to starting system.
- 0
- disable switch phyport...
- 3: System Boot system code via Flash.(0xbc020000)
- do_bootm:argc=2, addr=0xbc020000
- ## Booting image at bc020000 ...
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80000000) ...
- ## Giving linux memsize in MB, 64
- Starting kernel ...
- [ 0.000000] Linux version 5.4.46 (inflabz@PC) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13584-88aeb5c75e)) #0 Wed Jun 17 03:00:42 2020
- [ 0.000000] Board has DDR2
- [ 0.000000] Analog PMU set to hw control
- [ 0.000000] Digital PMU set to hw control
- [ 0.000000] SoC Type: MediaTek MT7628AN ver:1 eco:2
- [ 0.000000] printk: bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
- [ 0.000000] MIPS: machine is TP-Link TL-WR850N v2
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
- [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
- [ 0.000000] Writing ErrCtl register=0002ae40
- [ 0.000000] Readback ErrCtl register=0002ae40
- [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
- [ 0.000000] Memory: 57644K/65536K available (4543K kernel code, 193K rwdata, 1024K rodata, 1208K init, 197K bss, 7892K reserved, 0K cma-res)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS: 256
- [ 0.000000] intc: using register map from devicetree
- [ 0.000000] random: get_random_bytes called from start_kernel+0x32c/0x518 with crng_init=0
- [ 0.000000] CPU Clock: 580MHz
- [ 0.000000] timer_probe: no matching timers found
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
- [ 0.000009] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
- [ 0.007541] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
- [ 0.045449] pid_max: default: 32768 minimum: 301
- [ 0.050101] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.057123] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.070650] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
- [ 0.080075] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
- [ 0.086754] pinctrl core: initialized pinctrl subsystem
- [ 0.092961] NET: Registered protocol family 16
- [ 0.132407] clocksource: Switched to clocksource MIPS
- [ 0.138687] NET: Registered protocol family 2
- [ 0.143826] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
- [ 0.151938] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.159311] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.166108] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.172438] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
- [ 0.178725] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
- [ 0.185777] NET: Registered protocol family 1
- [ 0.190005] PCI: CLS 0 bytes, default 32
- [ 0.198334] workingset: timestamp_bits=14 max_order=14 bucket_order=0
- [ 0.213160] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.218791] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.244884] mt7621_gpio 10000600.gpio: registering 32 gpios
- [ 0.250573] mt7621_gpio 10000600.gpio: registering 32 gpios
- [ 0.256235] mt7621_gpio 10000600.gpio: registering 32 gpios
- [ 0.261921] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
- [ 0.269321] printk: console [ttyS0] disabled
- [ 0.273513] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
- [ 0.282241] printk: console [ttyS0] enabled
- [ 0.282241] printk: console [ttyS0] enabled
- [ 0.290650] printk: bootconsole [early0] disabled
- [ 0.290650] printk: bootconsole [early0] disabled
- [ 0.301502] spi-mt7621 10000b00.spi: sys_freq: 193333333
- [ 0.316260] spi-nor spi0.0: gd25q64 (8192 Kbytes)
- [ 0.321165] 4 fixed-partitions partitions found on MTD device spi0.0
- [ 0.327624] Creating 4 MTD partitions on "spi0.0":
- [ 0.332508] 0x000000000000-0x000000020000 : "boot"
- [ 0.338435] 0x000000020000-0x0000007c0000 : "firmware"
- [ 0.347089] 2 tplink-fw partitions found on MTD device firmware
- [ 0.353180] Creating 2 MTD partitions on "firmware":
- [ 0.358243] 0x000000000000-0x0000001d62aa : "kernel"
- [ 0.364354] 0x0000001d62ac-0x0000007a0000 : "rootfs"
- [ 0.370419] mtd: device 3 (rootfs) set to be root filesystem
- [ 0.377974] 1 squashfs-split partitions found on MTD device rootfs
- [ 0.384324] 0x000000460000-0x0000007a0000 : "rootfs_data"
- [ 0.390865] 0x0000007c0000-0x0000007d0000 : "config"
- [ 0.397048] 0x0000007d0000-0x000000800000 : "factory"
- [ 0.404018] libphy: Fixed MDIO Bus: probed
- [ 0.421024] rt3050-esw 10110000.esw: link changed 0x00
- [ 0.428245] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
- [ 0.438626] NET: Registered protocol family 10
- [ 0.447739] Segment Routing with IPv6
- [ 0.451688] NET: Registered protocol family 17
- [ 0.456302] 8021q: 802.1Q VLAN Support v1.8
- [ 0.471821] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
- [ 0.485861] Freeing unused kernel memory: 1208K
- [ 0.490485] This architecture does not have kernel memory protection.
- [ 0.497024] Run /sbin/init as init process
- [ 1.108438] random: fast init done
- [ 1.528784] init: Console is alive
- [ 1.532648] init: - watchdog -
- [ 2.680820] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 2.863851] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 2.881781] init: - preinit -
- [ 4.281645] random: jshn: uninitialized urandom read (4 bytes read)
- [ 4.371349] random: jshn: uninitialized urandom read (4 bytes read)
- [ 4.638583] random: jshn: uninitialized urandom read (4 bytes read)
- [ 5.253164] rt3050-esw 10110000.esw: link changed 0x00
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 5.484778] urandom_read: 2 callbacks suppressed
- [ 5.484788] random: procd: uninitialized urandom read (4 bytes read)
- [ 8.233342] rt3050-esw 10110000.esw: link changed 0x01
- [ 8.829284] rt3050-esw 10110000.esw: link changed 0x05
- [ 9.805359] jffs2: notice: (414) jffs2_build_xattr_subsystem: complete building xattr subsystem, 19 of xdatum (7 unchecked, 10 orphan) and .
- [ 9.823148] mount_root: switching to jffs2 overlay
- [ 9.854492] overlayfs: upper fs does not support tmpfile.
- [ 9.868766] urandom-seed: Seeding with /etc/urandom.seed
- [ 10.011781] procd: - early -
- [ 10.015647] procd: - watchdog -
- [ 10.668473] procd: - watchdog -
- [ 10.672009] procd: - ubus -
- [ 10.840729] random: ubusd: uninitialized urandom read (4 bytes read)
- [ 10.869425] random: ubusd: uninitialized urandom read (4 bytes read)
- [ 10.876574] random: ubusd: uninitialized urandom read (4 bytes read)
- [ 10.884491] procd: - init -
- Please press Enter to activate this console.
- [ 11.745867] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 11.797646] Loading modules backported from Linux version v5.7-rc3-0-g6a8b55ed4056
- [ 11.805401] Backport generated by backports.git v5.7-rc3-1-0-gc0c7d2bb
- [ 11.876706] xt_time: kernel timezone is -0000
- [ 11.999899] mt76_wmac 10300000.wmac: ASIC revision: 76280001
- [ 12.195591] urngd: v1.0.2 started.
- [ 12.403282] random: crng init done
- [ 12.406759] random: 1 urandom warning(s) missed due to ratelimiting
- [ 13.038661] mt76_wmac 10300000.wmac: Firmware Version: 20151201
- [ 13.044766] mt76_wmac 10300000.wmac: Build Time: 20151201183641
- [ 13.064416] mt76_wmac 10300000.wmac: firmware init done
- [ 13.351716] PPP generic driver version 2.4.2
- [ 13.369487] NET: Registered protocol family 24
- [ 13.406971] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 21.043396] rt3050-esw 10110000.esw: link changed 0x00
- [ 24.053306] rt3050-esw 10110000.esw: link changed 0x01
- [ 24.605242] rt3050-esw 10110000.esw: link changed 0x05
- [ 27.769474] br-lan: port 1(eth0.1) entered blocking state
- [ 27.775050] br-lan: port 1(eth0.1) entered disabled state
- [ 27.780964] device eth0.1 entered promiscuous mode
- [ 27.785883] device eth0 entered promiscuous mode
- [ 27.811841] br-lan: port 1(eth0.1) entered blocking state
- [ 27.817418] br-lan: port 1(eth0.1) entered forwarding state
- [ 28.771658] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement