Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.02.05 23:44:28 =~=~=~=~=~=~=~=~=~=~=~=
- T T
- Abort
- Erase linux kernel block !!
- From 0xBF050000 To 0xBF04FFFF
- Error: start and/or end address not on sector boundary
- Copy linux image[0 byte] to Flash[0xBF050000]....
- Zero length ???
- ## Booting image at bf050000 ...
- Bad Magic Number,FFFFFFFF
- U-Boot 1.1.3 (Feb 9 2010 - 10:44:20)
- Board: Ralink APSoC DRAM: 32 MB
- relocate_code Pointer at: 81fb0000
- flash_protect ON: from 0xBF000000 to 0xBF01D3F3
- flash_protect ON: from 0xBF030000 to 0xBF030FFF
- ============================================
- Ralink UBoot Version: 3.3
- --------------------------------------------
- ASIC 3052_MP2 (Port5<->None)
- DRAM component: 128 Mbits SDR
- DRAM bus: 32 bit
- Total memory: 32 MBytes
- Flash component: NOR Flash
- Date:Feb 9 2010 Time:10:44:20
- ============================================
- icache: sets:256, ways:4, linesz:32 ,total:32768
- dcache: sets:128, ways:4, linesz:32 ,total:16384
- ##### The CPU freq = 384 MHZ ####
- SDRAM bus set to 32 bit
- SDRAM size =32 Mbytes
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 9: Load Boot Loader code then write to Flash via TFTP.
- You choosed 2
- 0
- 2: System Load Linux Kernel then write to Flash via TFTP.
- Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
- Please Input new ones /or Ctrl-C to discard
- Input device IP (`! ) ==:`! 192.168.1.1
- Input server IP (`! ) ==:`! 192.168.1.2
- Input Linux Kernel filename () ==:2T2R.bin
- netboot_common, argc= 3
- NetTxPacket = 0x81FE5600
- KSEG1ADDR(NetTxPacket) = 0xA1FE5600
- NetLoop,call eth_halt !
- NetLoop,call eth_init !
- Trying Eth0 (10/100-M)
- Waitting for RX_DMA_BUSY status Start... done
- Header Payload scatter function is Disable !!
- ETH_STATE_ACTIVE!!
- Using Eth0 (10/100-M) device
- TFTP from server 192.168.1.2; our IP address is 192.168.1.1
- Filename '2T2R.bin'.
- TIMEOUT_COUNT=10,Load address: 0x80100000
- Loading: *Got ARP REPLY, set server/gtwy eth addr (00:50:8d:b7:fb:f8)
- Got it
- T #
- first block received
- ################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- ############################################################
- done
- Bytes transferred = 3631873 (376b01 hex)
- NetBootFileXferSize= 00376b01
- Erase linux kernel block !!
- From 0xBF050000 To 0xBF3CFFFF
- b_end =BF7FFFFF
- Erase Flash from 0xbf050000 to 0xbf3cffff in Bank # 1
- erase sector = 12
- sect = 12,s_last = 67,erase poll = 1077855
- erase sector = 13
- *sect = 13,s_last = 67,erase poll = 1067479
- erase sector = 14
- sect = 14,s_last = 67,erase poll = 1067544
- erase sector = 15
- *sect = 15,s_last = 67,erase poll = 1111626
- erase sector = 16
- sect = 16,s_last = 67,erase poll = 1066740
- erase sector = 17
- *sect = 17,s_last = 67,erase poll = 1065863
- erase sector = 18
- sect = 18,s_last = 67,erase poll = 1066165
- erase sector = 19
- *sect = 19,s_last = 67,erase poll = 1086888
- erase sector = 20
- sect = 20,s_last = 67,erase poll = 1111277
- erase sector = 21
- *sect = 21,s_last = 67,erase poll = 1103219
- erase sector = 22
- sect = 22,s_last = 67,erase poll = 1076384
- erase sector = 23
- *sect = 23,s_last = 67,erase poll = 1100999
- erase sector = 24
- sect = 24,s_last = 67,erase poll = 1098234
- erase sector = 25
- *sect = 25,s_last = 67,erase poll = 1069213
- erase sector = 26
- sect = 26,s_last = 67,erase poll = 1070900
- erase sector = 27
- *sect = 27,s_last = 67,erase poll = 1070018
- erase sector = 28
- sect = 28,s_last = 67,erase poll = 1081227
- erase sector = 29
- *sect = 29,s_last = 67,erase poll = 1071244
- erase sector = 30
- sect = 30,s_last = 67,erase poll = 1089584
- erase sector = 31
- *sect = 31,s_last = 67,erase poll = 1054111
- erase sector = 32
- sect = 32,s_last = 67,erase poll = 1109569
- erase sector = 33
- *sect = 33,s_last = 67,erase poll = 1104865
- erase sector = 34
- sect = 34,s_last = 67,erase poll = 1093890
- erase sector = 35
- *sect = 35,s_last = 67,erase poll = 1115290
- erase sector = 36
- *sect = 36,s_last = 67,erase poll = 1098637
- erase sector = 37
- sect = 37,s_last = 67,erase poll = 1071722
- erase sector = 38
- *sect = 38,s_last = 67,erase poll = 1055207
- erase sector = 39
- sect = 39,s_last = 67,erase poll = 1066849
- erase sector = 40
- *sect = 40,s_last = 67,erase poll = 1102497
- erase sector = 41
- sect = 41,s_last = 67,erase poll = 1111108
- erase sector = 42
- *sect = 42,s_last = 67,erase poll = 1078642
- erase sector = 43
- sect = 43,s_last = 67,erase poll = 1079673
- erase sector = 44
- *sect = 44,s_last = 67,erase poll = 1078145
- erase sector = 45
- sect = 45,s_last = 67,erase poll = 1066905
- erase sector = 46
- *sect = 46,s_last = 67,erase poll = 1078247
- erase sector = 47
- sect = 47,s_last = 67,erase poll = 1071114
- erase sector = 48
- *sect = 48,s_last = 67,erase poll = 1067124
- erase sector = 49
- sect = 49,s_last = 67,erase poll = 1086730
- erase sector = 50
- *sect = 50,s_last = 67,erase poll = 1074066
- erase sector = 51
- sect = 51,s_last = 67,erase poll = 1087626
- erase sector = 52
- *sect = 52,s_last = 67,erase poll = 1091076
- erase sector = 53
- sect = 53,s_last = 67,erase poll = 1071979
- erase sector = 54
- *sect = 54,s_last = 67,erase poll = 1224445
- erase sector = 55
- sect = 55,s_last = 67,erase poll = 1080073
- erase sector = 56
- *sect = 56,s_last = 67,erase poll = 1087723
- erase sector = 57
- sect = 57,s_last = 67,erase poll = 1053379
- erase sector = 58
- *sect = 58,s_last = 67,erase poll = 1111108
- erase sector = 59
- *sect = 59,s_last = 67,erase poll = 1091041
- erase sector = 60
- sect = 60,s_last = 67,erase poll = 1086417
- erase sector = 61
- *sect = 61,s_last = 67,erase poll = 1053369
- erase sector = 62
- sect = 62,s_last = 67,erase poll = 1104821
- erase sector = 63
- *sect = 63,s_last = 67,erase poll = 1068437
- erase sector = 64
- sect = 64,s_last = 67,erase poll = 1111952
- erase sector = 65
- *sect = 65,s_last = 67,erase poll = 1081454
- erase sector = 66
- sect = 66,s_last = 67,erase poll = 1073351
- erase sector = 67
- *sect = 67,s_last = 67,erase poll = 1068003
- done
- Erased 56 sectors
- Copy linux image[3631873 byte] to Flash[0xBF050000]....
- Copy to Flash...
- Copy 3631873 byte to Flash...
- addr = 0xBF0A3A6E ,cnt=3289235
- addr = 0xBF0F74F6 ,cnt=2946571
- addr = 0xBF14AF68 ,cnt=2603929
- addr = 0xBF19E9D2 ,cnt=2261295
- addr = 0xBF1F2438 ,cnt=1918665
- addr = 0xBF245EA4 ,cnt=1576029
- addr = 0xBF299916 ,cnt=1233387
- addr = 0xBF2ED386 ,cnt=890747
- addr = 0xBF340DF2 ,cnt=548111
- addr = 0xBF394862 ,cnt=205471 done
- ## Booting image at bf050000 ...
- Image Name: RT-NL
- Created: 2011-02-03 17:15:01 UTC
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 3631809 Bytes = 3.5 MB
- Load Address: 80000000
- Entry Point: 80220000
- Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80220000) ...
- ## Giving linux memsize in MB, 32
- Starting kernel ...
- Linux version 2.6.21.7 (sfstudio_at_mail.ru@wive-ng.sf.net or sadnet.ru) (gcc version 4.5.2 (GCC) ) #0 Thu Feb 3 23:09:40 OMST 2011
- ASIC mode LINUX started...
- The CPU frequency set to 384 MHz
- CPU revision is: 0001964c
- DetectRAMsequence
- MAX memory:[64]
- RAM after first pass:[67108864]
- RAM after second pass:[33554432]
- FullviewRAM:[33554432]
- Determined physical RAM map:
- memory: 02000000 @ 00000000 (usable)
- Built 1 zonelists. Total pages: 8128
- Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 ro
- start_kernel(): bug: interrupts were enabled *very* early, fixing it
- Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
- Primary data cache 16kB, 4-way, linesize 32 bytes.
- Synthesized clear page handler (25 instructions).
- Synthesized copy page handler (44 instructions).
- Synthesized TLB refill handler (20 instructions).
- Synthesized TLB load handler fastpath (32 instructions).
- Synthesized TLB store handler fastpath (32 instructions).
- Synthesized TLB modify handler fastpath (31 instructions).
- Cache parity protection disabled
- cause = c0808040, status = 11000000
- PID hash table entries: 128 (order: 7, 512 bytes)
- calculating r4koff... 0005dc00(384000)
- CPU frequency 384.00 MHz
- Using 192.000 MHz high precision timer.
- Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- Memory: 30140k/32768k available (1727k kernel code, 2628k reserved, 248k data, 292k init, 0k highmem)
- Mount-cache hash table entries: 512
- set cpu_wait to r4k_wait
- softirq RT prio: 24.
- NET: Registered protocol family 16
- Time: MIPS clocksource has been installed.
- NET: Registered protocol family 2
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 1024 (order: 1, 8192 bytes)
- TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- TCP: Hash tables configured (established 1024 bind 1024)
- TCP reno registered
- ralink flash device: 0x400000 at 0x1f000000
- Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
- NOR chip too large to fit in mapping. Attempting to cope...
- Amd/Fujitsu Extended Query Table at 0x0040
- number of CFI chips: 1
- Reducing visibility of 8192KiB chip to 4096KiB
- Creating 7 MTD partitions on "Ralink SoC physically mapped flash":
- 0x00000000-0x00030000 : "Bootloader"
- 0x00030000-0x00040000 : "Config"
- 0x00040000-0x00050000 : "Factory"
- 0x00050000-0x00101b01 : "Kernel_stub"
- 0x00101b01-0x003e0000 : "RootFS_stub"
- 0x003e0000-0x00400000 : "RW-FS"
- 0x00050000-0x003e0000 : "Kernel_RootFS"
- deice id : 0 0 0 0 0 (0)
- Warning: un-recognized chip ID, please update SPI driver!
- MX25L25635E(c2 2019c220) (32768 Kbytes)
- mtd .name = raspi, .size = 0x02000000 (32M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
- ralink_spi: No flash detected
- squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
- squashfs: LZMA suppport for slax.org by jro
- io scheduler noop registered (default)
- Ralink gpio driver initialized
- Number of GPIO=52
- Generic RTC Driver v1.07
- Ralink APSoC Hardware Watchdog Timer
- Serial: 8250/16550 driver $Revision: 1.6 $ 2 ports, IRQ sharing disabled
- serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
- serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
- Ralink APSoC Ethernet Driver Initilization. v2.0 512 rx/tx descriptors allocated, mtu = 1500!
- NAPI enable, weight = 64, Tx Ring = 512, Rx Ring = 512
- PROC INIT OK!
- block2mtd: version $Revision: 1.1.1.1 $
- nf_conntrack version 0.5.0 (16384 buckets, 2048 max)
- TCP cubic registered
- ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Fully Cone
- BCM fast NAT: INIT
- NET: Registered protocol family 1
- NET: Registered protocol family 17
- 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
- All bugs added by David S. Miller <davem@redhat.com>
- VFS: Mounted root (squashfs filesystem) readonly.
- Freeing unused kernel memory: 292k freed
- mount /proc file system ok!
- mount /sys file system ok!
- mount /dev file system ok!
- mount /var file system ok!
- Algorithmics/MIPS FPU Emulator v1.5
- INIT: Prepare start init!
- INIT: Init DEV particion
- INIT: Init RW particion
- zcat: invalid magic
- INIT: File system is clear or poor.
- INIT: Restored. Save after full boot and configure.
- INIT: Start init now.
- ~ # PRECONFIG: Preconfigure...
- PRECONFIG: Delete old config
- PRECONFIG: Mount all filesystems
- PRECONFIG: Create some folders
- PRECONFIG: Restore time to build time or save time
- Thu Feb 3 23:09:00 UTC 2011
- PRECONFIG: Copy web pages to tmpfs
- Check firmware update or clean boot.
- CHECKCONF: >>>> RESTORE NVRAM <<<<
- CHECKCONF: >>>> CLEAN MODE <<<<
- CHECKCONF: Burn RF template to flash
- Configure part at wifi factory.
- mtd write val = 128 11
- Flash RF defaults.
- 1+0 records in
- 1+0 records out
- CHECKCONF: Clear and load defaults to nvram !!!
- Load user defaults.
- Commit crc = cdb57fa8
- Commit crc = 94555289
- CHECKCONF: Get new variables...
- CHECKCONF: Reset OK... boot...
- CHECKCONF: First start MAC generate
- CHECKCONF: Set new mac!
- Commit crc = bc3b9d25
- Commit crc = a23483b9
- Commit crc = fc8b770e
- MODULES: Start modules.dep generate...
- ##### restore to dump switch #####
- switch reg write offset=14, value=5555
- switch reg write offset=40, value=1001
- switch reg write offset=44, value=1001
- switch reg write offset=48, value=1001
- switch reg write offset=4c, value=1
- switch reg write offset=50, value=2001
- switch reg write offset=70, value=ffffffff
- switch reg write offset=98, value=7f7f
- switch reg write offset=e4, value=7f
- switch reg write offset=e4, value=0
- ##### config vlan partition (LLLLW) #####
- switch reg write offset=14, value=405555
- switch reg write offset=50, value=2001
- switch reg write offset=98, value=7f3f
- switch reg write offset=e4, value=3f
- switch reg write offset=40, value=1002
- switch reg write offset=44, value=1001
- switch reg write offset=48, value=1001
- switch reg write offset=70, value=ffff417e
- ######## clear switch mac table ########
- done.
- MODULES: Reinit power mode for all switch ports
- Set: phy[0].reg[0] = 0800
- Set: phy[1].reg[0] = 0800
- Set: phy[2].reg[0] = 0800
- Set: phy[3].reg[0] = 0800
- Set: phy[4].reg[0] = 0800
- Set: phy[0].reg[0] = 9000
- Set: phy[1].reg[0] = 9000
- Set: phy[2].reg[0] = 9000
- Set: phy[3].reg[0] = 9000
- Set: phy[4].reg[0] = 9000
- Reset all phy port
- Set: phy[1].reg[0] = 3900
- Set: phy[2].reg[0] = 3900
- Set: phy[3].reg[0] = 3900
- Set: phy[4].reg[0] = 3900
- Set: phy[1].reg[0] = 3100
- Set: phy[2].reg[0] = 3100
- Set: phy[3].reg[0] = 3100
- Set: phy[4].reg[0] = 3100
- SYSLOG: Start klogd
- SYSLOG: Start syslogd
- PASSWD: Set current password
- Password for 'Admin' changed
- GENKEY: Generate host key for first start
- GENKEY: If no DSS key and generate new key
- GENKEY: Generate UUID for miniupnpd
- Will output 1024 bit dss secret key to '/etc/dropbear/dropbear_dss_host_key'
- Generating key, this may take a while...
- Public key portion is:
- ssh-dss 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 Admin@(none)
- Fingerprint: md5 26:18:33:b7:f0:bf:63:be:98:2d:aa:e5:64:e2:73:d7
- GENKEY: UPNP UUID is d32027b3-4f369f133-007d-42fd68ec3b5d , serial is 0
- RESOLVE: Generate resolve:
- LOOPBACK: Start loopback interface...
- LAN: Start network interfaces...
- LAN: -==Add bridge in the system==-
- LAN: -==BR0_MACADDR 00:0B:2B:15:15:2c==-
- LAN: -==Up bridge interface==-
- LAN: -==ETH2_MACADDR 0GDMA1_MAC_ADRH -- : 0x0000000b
- GDMA1_MAC_ADRL -- : 0x2b15152c
- 0:0B:2B:15:15:2c==-
- LAN: -==Up vlan root interf
- phy_tx_ring = 0x015aa000, tx_ring = 0xa15aa000
- phy_rx_ring = 0x015ac000, rx_ring = 0xa15ac000
- RT305x_ESW: Link Status Changed
- CDMA_CSG_CFG = 81000007
- GDMA1_FWD_CFG = 710000
- ace==-
- LAN: -==Add vlans and config==-
- LAN: -==ETH2.1_MACADDR 00:0B:2B:eth2.1: Setting MAC address to 00 0b 2b 15 15 2c.
- VLAN (eth2.1): Underlying device (eth2) has same MAC, not checking promiscious mode.
- 15:15:2c==-
- LAN: -==ETH2.2_MACADDR 00:0B:2B:eth2.2: Setting MAC address to 00 0b 2b 15 15 22.
- device eth2 entered promiscuous mode
- VLAN (eth2.2): Setting underlying device (eth2) to promiscious mode.
- 15:15:22==-
- LAN: Add LAN1 iface
- LAN: >>>>> Mode is 1, wan iface eth2.2, lan iface br0, adress 192.168.1.1 <<<<<
- BRSTP: Config br-stp:
- DNSSERVER: Starting DNSMASQ:
- INETD: Starting inetd:
- SYSCTL: Tune with sysctl:
- SYSCTL: Tune network stack and memory usadge fo small memory devices
- net.core.rmem_max = 4136960
- net.core.wmem_max = 4136960
- vm.min_free_kbytes = 2304
- net.netfilter.nf_conntrack_max = 4096
- net.nf_conntrack_max = 4096
- net.general_conntrack_max = 3696
- net.ipv4.netfilter.ip_conntrack_max = 4096
- net.ipv4.route.max_size = 32768
- net.ipv4.ip_local_port_range = 3072 11264
- SYSCTL: ##conntrack max:##hashsize:##route max:##route max:##portrange:
- SYSCTL: ##4096##2048##32768##3072 11264
- SYSCTL: Tune with proc
- WATCHDOG: Start watchdog
- GOAHEADWEBSERVER: Start goahead
- rm -f /etc/portforward
- rm -f /etc/macipfilter
- rm -f /etc/websfilter
- Content filter disabled.
- internet.sh
- Clear connection track table
- MODULES: link wifi down first
- MODULES: Unload wifi module...
- MODULES: Prepare wifi config...
- Commit crc = fc8b770e
- MODULES: AP/STA Normal mode. MAC: 00:0B:2B:15:15:c2
- MODULES: Load wifi module...
- MODULES: Link wifi up...
- 0x1300 = 00064380
- >>>>> RECONFIGURE WIFI <<<<<<<<<<
- LAN: Stop network interfaces...
- LAN: Start network interfaces...
- LAN: -==Add bridge in the system==-
- LAN: -==BR0_MACADDR 00:0B:2B:15:15:2c==-
- LAN: -==Up bridge interface==-
- LAN: -==Add vlans and config==-
- LAN: -==ETH2.1_MACADDR 00:0B:2B:eth2.1: Setting MAC address to 00 0b 2b 15 15 2c.
- VLAN (eth2.1): Underlying device (eth2) has same MAC, not checking promiscious mode.
- 15:15:2c==-
- LAN: -==ETH2.2_MACADDR 00:0B:2B:eth2.2: Setting MAC address to 00 0b 2b 15 15 22.
- 15:15:22==-
- LAN: Add LAN1 iface
- LAN: >>>>> Mode is 1, wan iface eth2.2, lan iface br0, adress 192.168.1.1 <<<<<
- WAN: Start wan config
- WAN: Configure WAN.
- net.ipv4.send_sigusr_dhcpc = 4
- WAN: Start DHCP pppoe_pass: Disabled.
- client.
- ipv6_pass: Disabled
- net.ipv4.netfilter.ip_conntrack_fastnat = 1
- net.ipv4.bridge_fastpath = 1
- DHCPSERVER: Stop dhcpserver
- PPPOERELAY: Stopping pppoe-relay:
- BRSTP: Disable stp on br0
- UDPXY: UDPXY stop
- IGMPPROXY: Stopping IGMPPROXY:
- LLD2D: Stopping LLD2D:
- IPTABLES: Stopping IPTABLES:
- IPTABLES: Starting IPTABLES:
- ipcalc: bad IP address:
- ipcalc: bad IP address:
- IPTABLES: Set default filters
- IPTABLES: Service limit set
- IPTABLES: web limit
- IPTABLES: ssh limit
- IPTABLES: udpxy limit
- IPTABLES: samba
- IPTABLES: icmp limit
- IPTABLES: Allow ping from wan eth2.2
- IPTABLES: Set forward rules
- net.ipv4.ip_forward = 1
- IPTABLES: Add masqrade rules
- IPTABLES: Iptables rules add OK...
- SHAPER: Stopping SHAPER:
- eth2
- ra0
- br0
- DHCPSERVER: Start dhcpserver
- BRSTP: Config br-stp:
- LLD2D: Starting LLD2D:
- lld2d: warning: line ignored - var does not match a known string
- net.ipv4.igmp_max_memberships = 5
- RIPD: Stopping RIPD:
- ZEBRA: Stopping ZEBRA:
- DNSSERVER: Stopping DNSMASQ:
- DNSSERVER: Starting DNSMASQ:
- UPNPD: Stop upnp
- NTP: Stopping NTPD:
- NTP: Set timezone:
- 23:09:45
- DYNDNS: Stopping DynDns:
- DYNDNS: Some parametrs needed...
- killall -q rt2860apd
- killall -q -9 rt2860apd
- ip route del 239.255.255.250 1>/dev/null 2>&1
- service wscd stop &
- iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
- service zebra restart &
- service ripd restart &
- service shaper restart &
- webs: Listening for HTTP requests at address 192.168.1.1
- WSCD: Stopping WPS:
- RIPD: Stopping RIPD:
- ZEBRA: Stopping ZEBRA:
- SHAPER: Stopping SHAPER:
- eth2
- ra0
- br0
- Clear connection track table
- Clear connection track table
- Store settings to backup file....
- crc = fc8b770e
- Save curent date and current time to rwfs
- Compress config files
- tar: removing leading '/' from member names
- Write configs to flash
- Config saved. OK.
- Clear connection track table
- Clear connection track table
- crc = fc8b770e
- tar: removing leading '/' from member names
- Clear connection track table
- The system is going down NOW!
- Sent SIGTERM to all processes
- Sent SIGKILL toRestarting system.
- U-Boot 1.1.3 (Feb 9 2010 - 10:44:20)
- Board: Ralink APSoC DRAM: 32 MB
- relocate_code Pointer at: 81fb0000
- flash_protect ON: from 0xBF000000 to 0xBF01D3F3
- flash_protect ON: from 0xBF030000 to 0xBF030FFF
- ============================================
- Ralink UBoot Version: 3.3
- --------------------------------------------
- ASIC 3052_MP2 (Port5<->None)
- DRAM component: 128 Mbits SDR
- DRAM bus: 32 bit
- Total memory: 32 MBytes
- Flash component: NOR Flash
- Date:Feb 9 2010 Time:10:44:20
- ============================================
- icache: sets:256, ways:4, linesz:32 ,total:32768
- dcache: sets:128, ways:4, linesz:32 ,total:16384
- ##### The CPU freq = 384 MHZ ####
- SDRAM bus set to 32 bit
- SDRAM size =32 Mbytes
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 9: Load Boot Loader code then write to Flash via TFTP.
- 4 3 2 1 0
- 3: System Boot system code via Flash.
- ## Booting image at bf050000 ...
- Image Name: RT-NL
- Created: 2011-02-03 17:15:01 UTC
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 3631809 Bytes = 3.5 MB
- Load Address: 80000000
- Entry Point: 80220000
- Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80220000) ...
- ## Giving linux memsize in MB, 32
- Starting kernel ...
- Linux version 2.6.21.7 (sfstudio_at_mail.ru@wive-ng.sf.net or sadnet.ru) (gcc version 4.5.2 (GCC) ) #0 Thu Feb 3 23:09:40 OMST 2011
- ASIC mode LINUX started...
- The CPU frequency set to 384 MHz
- CPU revision is: 0001964c
- DetectRAMsequence
- MAX memory:[64]
- RAM after first pass:[67108864]
- RAM after second pass:[33554432]
- FullviewRAM:[33554432]
- Determined physical RAM map:
- memory: 02000000 @ 00000000 (usable)
- Built 1 zonelists. Total pages: 8128
- Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 ro
- start_kernel(): bug: interrupts were enabled *very* early, fixing it
- Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
- Primary data cache 16kB, 4-way, linesize 32 bytes.
- Synthesized clear page handler (25 instructions).
- Synthesized copy page handler (44 instructions).
- Synthesized TLB refill handler (20 instructions).
- Synthesized TLB load handler fastpath (32 instructions).
- Synthesized TLB store handler fastpath (32 instructions).
- Synthesized TLB modify handler fastpath (31 instructions).
- Cache parity protection disabled
- cause = 50808000, status = 11000000
- PID hash table entries: 128 (order: 7, 512 bytes)
- calculating r4koff... 0005dc00(384000)
- CPU frequency 384.00 MHz
- Using 192.000 MHz high precision timer.
- Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- Memory: 30140k/32768k available (1727k kernel code, 2628k reserved, 248k data, 292k init, 0k highmem)
- Mount-cache hash table entries: 512
- set cpu_wait to r4k_wait
- softirq RT prio: 24.
- NET: Registered protocol family 16
- Time: MIPS clocksource has been installed.
- NET: Registered protocol family 2
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 1024 (order: 1, 8192 bytes)
- TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- TCP: Hash tables configured (established 1024 bind 1024)
- TCP reno registered
- ralink flash device: 0x400000 at 0x1f000000
- Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
- NOR chip too large to fit in mapping. Attempting to cope...
- Amd/Fujitsu Extended Query Table at 0x0040
- number of CFI chips: 1
- Reducing visibility of 8192KiB chip to 4096KiB
- Creating 7 MTD partitions on "Ralink SoC physically mapped flash":
- 0x00000000-0x00030000 : "Bootloader"
- 0x00030000-0x00040000 : "Config"
- 0x00040000-0x00050000 : "Factory"
- 0x00050000-0x00101b01 : "Kernel_stub"
- 0x00101b01-0x003e0000 : "RootFS_stub"
- 0x003e0000-0x00400000 : "RW-FS"
- 0x00050000-0x003e0000 : "Kernel_RootFS"
- deice id : 0 0 0 0 0 (0)
- Warning: un-recognized chip ID, please update SPI driver!
- MX25L25635E(c2 2019c220) (32768 Kbytes)
- mtd .name = raspi, .size = 0x02000000 (32M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
- ralink_spi: No flash detected
- squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
- squashfs: LZMA suppport for slax.org by jro
- io scheduler noop registered (default)
- Ralink gpio driver initialized
- Number of GPIO=52
- Generic RTC Driver v1.07
- Ralink APSoC Hardware Watchdog Timer
- Serial: 8250/16550 driver $Revision: 1.6 $ 2 ports, IRQ sharing disabled
- serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
- Љserial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
- Ralink APSoC Ethernet Driver Initilization. v2.0 512 rx/tx descriptors allocated, mtu = 1500!
- NAPI enable, weight = 64, Tx Ring = 512, Rx Ring = 512
- PROC INIT OK!
- block2mtd: version $Revision: 1.1.1.1 $
- nf_conntrack version 0.5.0 (16384 buckets, 2048 max)
- TCP cubic registered
- ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Fully Cone
- BCM fast NAT: INIT
- NET: Registered protocol family 1
- NET: Registered protocol family 17
- 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
- All bugs added by David S. Miller <davem@redhat.com>
- VFS: Mounted root (squashfs filesystem) readonly.
- Freeing unused kernel memory: 292k freed
- mount /proc file system ok!
- mount /sys file system ok!
- mount /dev file system ok!
- mount /var file system ok!
- Algorithmics/MIPS FPU Emulator v1.5
- INIT: Prepare start init!
- INIT: Init DEV particion
- INIT: Init RW particion
- INIT: RW File system is ok - preparing ...
- INIT: Start init now.
- ~ # PRECONFIG: Preconfigure...
- PRECONFIG: Delete old config
- PRECONFIG: Mount all filesystems
- PRECONFIG: Create some folders
- PRECONFIG: Restore time to build time or save time
- Fri Feb 4 23:12:00 GMT 2011
- PRECONFIG: Copy web pages to tmpfs
- Check firmware update or clean boot.
- CHECKCONF: >>>> NORMAL BOOT <<<<
- ##### restore to dump switch #####
- switch reg write offset=14, value=5555
- switch reg write offset=40, value=1001
- switch reg write offset=44, value=1001
- switch reg write offset=48, value=1001
- switch reg write offset=4c, value=1
- switch reg write offset=50, value=2001
- switch reg write offset=70, value=ffffffff
- switch reg write offset=98, value=7f7f
- switch reg write offset=e4, value=7f
- switch reg write offset=e4, value=0
- ##### config vlan partition (LLLLW) #####
- switch reg write offset=14, value=405555
- switch reg write offset=50, value=2001
- switch reg write offset=98, value=7f3f
- switch reg write offset=e4, value=3f
- switch reg write offset=40, value=1002
- switch reg write offset=44, value=1001
- switch reg write offset=48, value=1001
- switch reg write offset=70, value=ffff417e
- ######## clear switch mac table ########
- done.
- MODULES: Reinit power mode for all switch ports
- Set: phy[0].reg[0] = 0800
- Set: phy[1].reg[0] = 0800
- Set: phy[2].reg[0] = 0800
- Set: phy[3].reg[0] = 0800
- Set: phy[4].reg[0] = 0800
- Set: phy[0].reg[0] = 9000
- Set: phy[1].reg[0] = 9000
- Set: phy[2].reg[0] = 9000
- Set: phy[3].reg[0] = 9000
- Set: phy[4].reg[0] = 9000
- Reset all phy port
- Set: phy[1].reg[0] = 3900
- Set: phy[2].reg[0] = 3900
- Set: phy[3].reg[0] = 3900
- Set: phy[4].reg[0] = 3900
- Set: phy[1].reg[0] = 3100
- Set: phy[2].reg[0] = 3100
- Set: phy[3].reg[0] = 3100
- Set: phy[4].reg[0] = 3100
- SYSLOG: Start klogd
- SYSLOG: Start syslogd
- PASSWD: Set current password
- Password for 'Admin' changed
- GENKEY: DSS file exist
- GENKEY: Use exist UUID file
- RESOLVE: Generate resolve:
- LOOPBACK: Start loopback interface...
- LAN: Start network interfaces...
- LAN: -==Add bridge in the system==-
- LAN: -==BR0_MACADDR 00:0B:2B:15:15:2c==-
- LAN: -==Up bridge interface==-
- LAN: -==ETH2_MACADDR 0GDMA1_MAC_ADRH -- : 0x0000000b
- GDMA1_MAC_ADRL -- : 0x2b15152c
- 0:0B:2B:15:15:2c==-
- LAN: -==Up vlan root interf
- phy_tx_ring = 0x018e0000, tx_ring = 0xa18e0000
- phy_rx_ring = 0x018e2000, rx_ring = 0xa18e2000
- RT305x_ESW: Link Status Changed
- CDMA_CSG_CFG = 81000007
- GDMA1_FWD_CFG = 710000
- ace==-
- LAN: -==Add vlans and config==-
- LAN: -==ETH2.1_MACADDR 00:0B:2B:eth2.1: Setting MAC address to 00 0b 2b 15 15 2c.
- VLAN (eth2.1): Underlying device (eth2) has same MAC, not checking promiscious mode.
- 15:15:2c==-
- LAN: -==ETH2.2_MACADDR 00:0B:2B:eth2.2: Setting MAC address to 00 0b 2b 15 15 22.
- device eth2 entered promiscuous mode
- VLAN (eth2.2): Setting underlying device (eth2) to promiscious mode.
- 15:15:22==-
- LAN: Add LAN1 iface
- LAN: >>>>> Mode is 1, wan iface eth2.2, lan iface br0, adress 192.168.1.1 <<<<<
- BRSTP: Config br-stp:
- DNSSERVER: Starting DNSMASQ:
- INETD: Starting inetd:
- SYSCTL: Tune with sysctl:
- SYSCTL: Tune network stack and memory usadge fo small memory devices
- net.core.rmem_max = 4946944
- net.core.wmem_max = 4946944
- vm.min_free_kbytes = 2304
- net.netfilter.nf_conntrack_max = 4096
- net.nf_conntrack_max = 4096
- net.general_conntrack_max = 3696
- net.ipv4.netfilter.ip_conntrack_max = 4096
- net.ipv4.route.max_size = 32768
- net.ipv4.ip_local_port_range = 3072 11264
- SYSCTL: ##conntrack max:##hashsize:##route max:##route max:##portrange:
- SYSCTL: ##4096##2048##32768##3072 11264
- SYSCTL: Tune with proc
- WATCHDOG: Start watchdog
- GOAHEADWEBSERVER: Start goahead
- rm -f /etc/portforward
- rm -f /etc/macipfilter
- rm -f /etc/websfilter
- Content filter disabled.
- internet.sh
- MODULES: link wifi down first
- MODULES: Unload wifi module...
- MODULES: Prepare wifi config...
- Commit crc = fc8b770e
- Clear connection track table
- MODULES: AP/STA Normal mode. MAC: 00:0B:2B:15:15:c2
- MODULES: Load wifi module...
- MODULES: Link wifi up...
- 0x1300 = 00064380
- >>>>> RECONFIGURE WIFI <<<<<<<<<<
- LAN: Stop network interfaces...
- LAN: Start network interfaces...
- LAN: -==Add bridge in the system==-
- LAN: -==BR0_MACADDR 00:0B:2B:15:15:2c==-
- LAN: -==Up bridge interface==-
- LAN: -==Add vlans and config==-
- LAN: -==ETH2.1_MACADDR 00:0B:2B:eth2.1: Setting MAC address to 00 0b 2b 15 15 2c.
- VLAN (eth2.1): Underlying device (eth2) has same MAC, not checking promiscious mode.
- 15:15:2c==-
- LAN: -==ETH2.2_MACADDR 00:0B:2B:eth2.2: Setting MAC address to 00 0b 2b 15 15 22.
- 15:15:22==-
- LAN: Add LAN1 iface
- LAN: >>>>> Mode is 1, wan iface eth2.2, lan iface br0, adress 192.168.1.1 <<<<<
- WAN: Start wan config
- WAN: Configure WAN.
- net.ipv4.send_sigusr_dhcpc = 4
- WAN: Start DHCP pppoe_pass: Disabled.
- client.
- ipv6_pass: Disabled
- net.ipv4.netfilter.ip_conntrack_fastnat = 1
- net.ipv4.bridge_fastpath = 1
- DHCPSERVER: Stop dhcpserver
- PPPOERELAY: Stopping pppoe-relay:
- BRSTP: Disable stp on br0
- UDPXY: UDPXY stop
- IGMPPROXY: Stopping IGMPPROXY:
- LLD2D: Stopping LLD2D:
- IPTABLES: Stopping IPTABLES:
- IPTABLES: Starting IPTABLES:
- ipcalc: bad IP address:
- ipcalc: bad IP address:
- IPTABLES: Set default filters
- IPTABLES: Service limit set
- IPTABLES: web limit
- IPTABLES: ssh limit
- IPTABLES: udpxy limit
- IPTABLES: samba
- IPTABLES: icmp limit
- IPTABLES: Allow ping from wan eth2.2
- IPTABLES: Set forward rules
- net.ipv4.ip_forward = 1
- IPTABLES: Add masqrade rules
- IPTABLES: Iptables rules add OK...
- SHAPER: Stopping SHAPER:
- eth2
- ra0
- br0
- DHCPSERVER: Start dhcpserver
- BRSTP: Config br-stp:
- LLD2D: Starting LLD2D:
- lld2d: warning: line ignored - var does not match a known string
- net.ipv4.igmp_max_memberships = 5
- RIPD: Stopping RIPD:
- ZEBRA: Stopping ZEBRA:
- DNSSERVER: Stopping DNSMASQ:
- DNSSERVER: Starting DNSMASQ:
- UPNPD: Stop upnp
- NTP: Stopping NTPD:
- NTP: Set timezone:
- 23:12:23
- DYNDNS: Stopping DynDns:
- DYNDNS: Some parametrs needed...
- killall -q rt2860apd
- killall -q -9 rt2860apd
- ip route del 239.255.255.250 1>/dev/null 2>&1
- service wscd stop &
- iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
- service zebra restart &
- service ripd restart &
- service shaper restart &
- webs: Listening for HTTP requests at address 192.168.1.1
- WSCD: Stopping WPS:
- RIPD: Stopping RIPD:
- ZEBRA: Stopping ZEBRA:
- SHAPER: Stopping SHAPER:
- eth2
- ra0
- br0
- Clear connection track table
- Clear connection track table
- Store settings to backup file....
- crc = fc8b770e
- Save curent date and current time to rwfs
- Compress config files
- tar: removing leading '/' from member names
- Write configs to flash
- Config saved. OK.
- Clear connection track table
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement