D-Link DNS-325 U-Boot

 ** MARVELL BOARD: DB-88F6281A-BP LE

U-Boot 1.1.4 (Jan 21 2011 - 09:42:39) Marvell version: 3.4.14.DNS-325.02

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CEE80

Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x100000, size 0x300000
load addr ....  =a00000

 3145728 bytes read: OK

NAND read: device 0 offset 0x600000, size 0x300000
load addr ....  =f00000

 3145728 bytes read: OK
## Booting image at 00a00000 ...
   Image Name:   Linux-2.6.31.8
   Created:      2012-06-26   3:38:43 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2565784 Bytes =  2.4 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00f00000 ...
   Image Name:   Ramdisk
   Created:      2014-01-21   4:33:41 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    1581012 Bytes =  1.5 MB
   Load Address: 00e00000
   Entry Point:  00e00000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux.............................................................
Linux version 2.6.31.8 (jack@swtest6) (gcc version 4.2.1) #8 Tue Jun 26 11:38:42
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 65024
Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 246528KB available (4828K code, 323K data, 136K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1186.20 BogoMIPS (lpj=5931008)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....base 10000000, size 256MB
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size   1MB
PEX1_MEM ....no such
PEX1_IO ....no such
INTER_REGS ....base f1000000, size   1MB
NFLASH_CS ....base fa000000, size   2MB
SPI_CS ....base f4000000, size  16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size   2MB

  Marvell Development Board (LSP Version KW_LSP_5.1.3_patch29)-- DB-88F6281A-BPE

 Detected Tclk 200000000 and SysClk 400000000
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c8040740
PEX0 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 1540K
rtc mv_rtc: rtc core: registered kw-rtc as rtc0
RTC registered
cpufreq: Init kirkwood cpufreq driver
XOR registered 4 channels
XOR 2nd invalidate WA enabled
cesadev_init(c000edb8)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
MV Buttons Driver Load
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
fuse init (API version 7.12)
msgmni has been set to 485
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for lzma (lzma-generic)
alg: No test for stdrng (krng)
alg: No test for hmac(digest_null) (hmac(digest_null-generic))
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered (default)
Initializing ths8200_init
Initializing dove_adi9889_init
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
Loading Marvell Ethernet Driver:
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o 2 Giga ports supported
  o Single RX Queue support - ETH_DEF_RXQ=0
  o Single TX Queue support - ETH_DEF_TXQ=0
  o TCP segmentation offload (TSO) supported
  o Large Receive offload (LRO) supported
  o Receive checksum offload supported
  o Transmit checksum offload supported
  o Network Fast Processing (Routing) supported - (Disabled)
  o Driver ERROR statistics enabled
  o Proc tool API enabled
  o SKB Reuse supported - (Disabled)
  o SKB Recycle supported - (Disabled)
  o Rx descripors: q0=128
  o Tx descripors: q0=532
  o Loading network interface(s):
     o register under mv88fx_eth platform
     o egiga0, ifindex = 2, GbE port = 0

Warning: Giga 1 is Powered Off

mvFpRuleDb (c8252000): 2048 entries, 8192 bytes
Counter=0, opIdx=6, overhead=16
Counter=1, opIdx=2, overhead=0
Counter=2, opIdx=1, overhead=18
Counter=3, opIdx=2, overhead=0
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-b)
Scanning device for bad blocks
Using static partition definition
Creating 6 MTD partitions on "nand_mtd":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000600000 : "uImage"
0x000000600000-0x000000b00000 : "ramdisk"
0x000000b00000-0x000007100000 : "image"
0x000007100000-0x000007b00000 : "mini firmware"
0x000007b00000-0x000008000000 : "config"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
rtc mv_rtc: setting system clock to 2017-04-21 16:30:05 UTC (1492792205)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
RAMDISK: gzip image found at block 0
usb 1-1: new high speed USB device using ehci_marvell and address 2
VFS: Mounted root (ext2 filesystem) on device 1:0.
Freeing init memory: 136K
init started: BusyBox v1.11.2 (2013-04-15 17:30:08 CST)
starting pid 526, tty '': '/etc/rc.sh'
** Mounting /etc/fstab
umount: proc: not mounted
umount: proc: not mounted
umount: /usr/local/modules: not mounted
usb 1-1: configuration #1 chosen from 1 choice
first good block is 0
image len = 36925440 , image checksum = 114ac32
umount: /usr/local/tmp: not mounted
dump image checksum=114ac32
mount cmd:mount -t squashfs -o loop /usr/local/tmp/image.cfs /usr/local/modules
ln: /usr/sbin/./system_init: File exists
hardware init
GbE port 0: TxEnable WA - Enabled, deep=1, tx_en_bk=1

mtd check v1.01.05292012
/usr/local/config free size is 4653056
** copy config files
usbcore: registered new interface driver usblp
** set loopback interface
old ver:20150519
new ver:20150519
first good block is 0
mac1 = FC:75:16:03:D4:66
lan0:ifconfig egiga0 hw ether FC:75:16:03:D4:66
egiga0: mac address changed
egiga0: started
DNS-325 function
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): egiga0: link is not ready
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
IPv4 over IPv4 tunneling driver
tunl0: Disabled Privacy Extensions
net.ipv6.conf.default.accept_dad = 2
net.ipv6.conf.egiga0.accept_dad = 2
net.ipv6.conf.default.dad_transmits = 1
net.ipv6.conf.egiga0.dad_transmits = 1
net.ipv6.conf.default.forwarding = 0
net.ipv6.conf.default.accept_redirects = 1
*** execute rc.init.sh
192.168.0.32
requested_ip=192.168.0.32
udhcpc (v1.11.2) started
Sending discover...
Sending discover...
Sending discover...
No lease, forking to background
hostname=[dlink-03D466]
*** set Time Zone ****
Fri Apr 21 20:31:01 MSK 2017
*** get Time from rtc and set it into system ****
rtc: RTC time = 2017/4/21 Fri 16:31:1
Fri Apr 21 20:31:01 MSK 2017
*** Do not adjust RTC time ***

Module IPC SERVER Version:(1.00.20090706)

hd verify v1.02.20110719
can not detect hd
** Get MAC Addr
SIOCGIFNETMASK: Cannot assign requested address
op_server v2.01.06012006
init socket fail!
Starting system message bus
created mail daemon thread 0
**LLTD UNDER VLAN DISABLE****
cp: cannot stat '/usr/local/config/ups_slave.dat': No such file or directory
sh: you need to specify whom to kill
sh: you need to specify whom to kill

Auto configuration for Linux client of no-ip.com.

error - gethostbyname: Host name lookup failure
error - gethostbyname
Can't gethostbyname for dynupdate.no-ip.com
Network must be operational to create configfile. Ending!
Can't locate configuration file /etc/no-ip2.conf. (Try -c). Ending!

mkdir: cannot create directory '/etc/hotplug': File exists
Error: Set IP_ADD_MEMBERSHIP fail!
Error: Set IP_ADD_MEMBERSHIP fail!
2017-04-21 20:31:13: (../../src/log.c.166) server started
system daemon v1.02.20120628
chk_io v1.02.20120118
support usb storage unmount
disk mode is            standard
mount normal
Setting up swapspace version 1, size = 18446744073709547520 bytes
mkswap: lseek(1024): Invalid argument
Unable to find swap-space signature
swapon: /dev/md0: Invalid argument

mfg_svr version 1.01(2015-05-19)


mfg_start version 1.00(2012-06-22)

Fri Apr 21 20:31:15 2017

local ip 0 (0.0.0.0)
netmask  0 (0.0.0.0)
Error JOIN multicast group: No such device

Please press Enter to activate this console. killall: set_pwm: no process killed
LED_POWER_ON
sata_hotplug v1.00.20100112
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi 2:0:0:0: Direct-Access     SanDisk  Ultra Fit        1.00 PQ: 0 ANSI: 6
sd 2:0:0:0: [sdc] 30031250 512-byte logical blocks: (15.3 GB/14.3 GiB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Assuming drive cache: write through
sd 2:0:0:0: [sdc] Assuming drive cache: write through
 sdc: sdc1
sd 2:0:0:0: Attached scsi generic sg0 type 0
sd 2:0:0:0: [sdc] Assuming drive cache: write through
sd 2:0:0:0: [sdc] Attached SCSI removable disk
NTFS driver 2.1.29 [Flags: R/O MODULE].
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will !
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sdc.
FAT: Unrecognized mount option "iocharset=utf8" or missing value
VFS: Can't find ext3 filesystem on dev sdc.
VFS: Can't find an ext2 filesystem on dev sdc.
EXT4-fs (sdc): VFS: Can't find ext4 filesystem
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will !
usb_dir </mnt/USB/HD_c1>
filename_mfg mfg_DNS_325
check /mnt/USB/HD_c1/mfg_DNS_325 file
open  /mnt/USB/HD_c1/mfg_DNS_325 file failed
2017-04-21 20:31:55: (../../src/server.c.1396) [note] graceful shutdown started
2017-04-21 20:31:55: (../../src/log.c.166) server started
2017-04-21 20:31:55: (../../src/server.c.1512) server stopped by UID = 0 PID =