# generated by Slic3r 1.3.0 on 2019-03-24 12:04:16
adaptive_slicing = 0
adaptive_slicing_quality = 75%
avoid_crossing_perimeters = 0
bed_shape = 0x0,300x0,300x300,0x300
bed_temperature = 65
before_layer_gcode = ; Layer [layer_num]\nM117 Layer [layer_num]
between_objects_gcode =
bottom_infill_pattern = rectilinear
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 0
brim_connections_width = 0
brim_width = 0
compatible_printers =
complete_objects = 0
cooling = 0
default_acceleration = 0
disable_fan_first_layers = 1
dont_support_bridges = 1
duplicate_distance = 6
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\nM107 ;turn off fan\nM140 S0;bed off
external_perimeter_extrusion_width = 0
external_perimeter_speed = 0
external_perimeters_first = 1
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #000000
filament_cost = 299
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 0
filament_notes = ""
filament_settings_id =
fill_angle = 45
fill_density = 10%
fill_gaps = 1
fill_pattern = 3dhoneycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 70
first_layer_extrusion_width = 120%
first_layer_height = 150%
first_layer_speed = 30
first_layer_temperature = 210
gap_fill_speed = 0
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
has_heatbed = 1
host_type = octoprint
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 53%
infill_speed = 0
interface_shells = 0
interior_brim_width = 0
layer_gcode =
layer_height = 0.3
match_horizontal_surfaces = 0
max_fan_speed = 100
max_layer_height = 0.3
max_print_speed = 70
max_volumetric_speed = 0
min_fan_speed = 100
min_layer_height = 0.15
min_print_speed = 10
min_skirt_length = 0
notes =
nozzle_diameter = 0.4
octoprint_apikey = E07EE726157944028BA5666FEBB74B89
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 0
perimeters = 3
post_process =
pressure_advance = 0
print_host = octopi.slagskepp.se
print_settings_id =
printer_notes =
printer_settings_id =
raft_layers = 0
regions_overlap = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 0
retract_length = 6
retract_length_toolchange = 10
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
seam_position = aligned
sequential_print_priority = 0
serial_port =
serial_speed = 250000
shortcuts = support_material
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 5
small_perimeter_speed = 0
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 0
spiral_vase = 0
standby_temperature_delta = -5
start_filament_gcode = "; Filament gcode\n"
start_gcode = ;------------Beginning of start gcode\nM107 ;turn off fan\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 X0 Y0 Z0 ; home X, Y and Z axis end-stops\nG29 L1  ; Load mesh in slot 1\nG29 J     ; Probe 3 points and tilt mesh\n; G0 X0 Y0 F9000 ; Go to front\n; 40mm from front of BP to avoid clips\nG0 Y40 F5000 ; Go to line first Y\nG0 X10 F5000 ; Go to line then X\nG0 Z0.20 ; Drop to bed (was 0.15, too tight)\nG92 E0 ; zero the extruded length\nG1 Y60 E15 F500 ; Extrude 15mm of filament in a 4cm line\nG92 E0 ; zero the extruded length\nG1 E-3 F500 ; Retract a little\nG1 Y80 F4000 ; Quickly wipe away from the filament line\nG1 Z2 ; Raise and begin printing.\n;------------------END of start-gcode
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 1
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_extrusion_width = 0
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_max_layers = 0
support_material_pattern = pillars
support_material_spacing = 3
support_material_speed = 0
support_material_threshold = 80%
temperature = 205
thin_walls = 1
threads = 8
toolchange_gcode =
top_infill_extrusion_width = 0
top_infill_pattern = rectilinear
top_solid_infill_speed = 0
top_solid_layers = 3
travel_speed = 200
use_firmware_retraction = 0
use_relative_e_distances = 0
use_set_and_wait_bed = 0
use_set_and_wait_extruder = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
xy_size_compensation = 0
z_offset = 0
z_steps_per_mm = 0