API tools faq
paste
Advertisement
pfeerick

pine_cube_card0 serial output

pfeerick
Jul 1st, 2021
347
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 34.87 KB | None | 0 0
raw download clone embed print report
  1. axp_set_power_supply_output ldo4_vol = 1800
  2. [ 2.466]DRAM: 128 MiB
  3. save config for small mem_size
  4. workmode = 16
  5. [debug_jaosn]:use the clock in sys_config
  6. OK
  7. spinor id is 0
  8. try nor successed
  9. sunxi sprite has installed spi function
  10. read flash error
  11. env_relocate_spec storage_type = 3
  12. In: serial
  13. Out: serial
  14. Err: serial
  15. mbr not exist
  16. [ 2.526]Hit any key to stop autoboot: 0
  17. work mode=0x10
  18. run usb efex
  19. delay time 2500
  20. usb init ok
  21. set address 0x6
  22. sunxi spinor is already inited
  23. flash size =16 M
  24. algin 512 byte fullimg_size 14155776
  25. FEX_CMD_fes_verify_status
  26. FEX_CMD_fes_verify last err=0
  27. before sunxi_sprite_setdata_finish
  28. spinor_datafinish
  29. spinor id = 0x0
  30. HELLO! BOOT0 is starting!
  31. get_ifm reg_val=0
  32. DRAM DRIVE INFO: V0.7
  33. DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
  34. DRAM CLK = 600 MHz
  35. DRAM zq value: 000039bb
  36. DRAM size = 128 MB
  37. Succeed in reading Boot1 file head.
  38. Jump to secend Boot.
  39. [ 0.070]
  40.  
  41. U-Boot 2011.09-rc1-00015-g2a49edf (Dec 21 2015 - 10:23:31) Allwinner Technology
  42.  
  43. [ 0.079]version: 1.1.0
  44. [ 0.084]pmbus:
  45. ===i2c gpio === 22777722
  46. ready
  47. [ 0.093]PMU: AXP20x found
  48. set power on vol to default
  49. axp_set_power_supply_output dcdc2_vol = 1250
  50. axp_set_power_supply_output dcdc3_vol = 3300
  51. axp_set_power_supply_output aldo2_vol = 2500
  52. axp_set_power_supply_output aldo3_vol = 3000
  53. axp_set_power_supply_output ldo1_vol = 3300
  54. axp_set_power_supply_output ldo2_vol = 3000
  55. axp_set_power_supply_output ldo3_vol = 2800
  56. axp_set_power_supply_output ldo4_vol = 1800
  57. [ 0.133]DRAM: 128 MiB
  58. [debug_jaosn]:use the clock in sys_config
  59. OK
  60. [ 0.152]sunxi flash init ok
  61. hello @flash_speed=1
  62. env_relocate_spec storage_type = 3
  63. In: serial
  64. Out: serial
  65. Err: serial
  66. WORK_MODE_BOOT
  67. read bootlogo partition successful,start_block=0x67a0,rblock=0x100 ,ret=256
  68. Use decode 2x2 sampling
  69. sunxi_read_bootlogo: jpg convert argb
  70. [ 0.259]Hit any key to stop autoboot: 0
  71. read boot or recovery all
  72. [ 1.541]sunxi flash read :offset 4000, 2884095 bytes OK
  73. [ 1.547]ready to boot
  74. [ 1.549]
  75. Starting kernel ...
  76.  
  77. [ 0.000000] Booting Linux on physical CPU 0
  78. [ 0.000000] Linux version 3.4.39 (given@Build001) (gcc version 4.6.3 20120201 (prerelease) (crosstool-NG linaro-1.13.1-2012.02-20120222 - Linaro GCC 2012.02) ) #32 Wed Jul 22 10:03:08 CST 2020
  79. [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
  80. [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  81. [ 0.000000] Machine: sun8i
  82. [ 0.000000] Initialized persistent memory from 41d00800-41d107ff
  83. [ 0.000000] Memory policy: ECC disabled, Data cache writeback
  84. [ 0.000000] On node 0 totalpages: 32768
  85. [ 0.000000] free_area_init_node: node 0, pgdat c04d3474, node_mem_map c056e000
  86. [ 0.000000] Normal zone: 256 pages used for memmap
  87. [ 0.000000] Normal zone: 0 pages reserved
  88. [ 0.000000] Normal zone: 32512 pages, LIFO batch:7
  89. [ 0.000000] script_init enter!
  90. [ 0.000000] script_init exit!
  91. [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
  92. [ 0.000000] pcpu-alloc: [0] 0
  93. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
  94. [ 0.000000] Kernel command line: console=ttyS2,115200 root=/dev/nor1 init=/init loglevel=8 partitions= mac_addr= uid=1234567890 kmemleak=on fb_base=0x41b00000 boot_type=3 sunxi_mbr=boot@[32:5632]system@[5664:19840]cfg@[25504:1024]boot_logo@[26528:256]shutdown_logo@[26784:256]env@[27040:128]private@[27168:128]UDISK@[27296:0] config_size=32420
  95. [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
  96. [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  97. [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  98. [ 0.000000] Memory: 128MB = 128MB total
  99. [ 0.000000] Memory: 36964k/36964k available, 94108k reserved, 0K highmem
  100. [ 0.000000] Virtual kernel memory layout:
  101. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  102. [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  103. [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
  104. [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
  105. [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
  106. [ 0.000000] .text : 0xc0008000 - 0xc046b000 (4492 kB)
  107. [ 0.000000] .init : 0xc046b000 - 0xc048e000 ( 140 kB)
  108. [ 0.000000] .data : 0xc048e000 - 0xc04d3b80 ( 279 kB)
  109. [ 0.000000] .bss : 0xc04d3ba4 - 0xc056d8e8 ( 616 kB)
  110. [ 0.000000] NR_IRQS:544
  111. [ 0.000000] 532 ahb1 set parent pll_periph0d2
  112. [ 0.000000] Architected local timer running at 24.00MHz.
  113. [ 0.000000] Switching to timer-based delay loop
  114. [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
  115. [ 0.000000] Console: colour dummy device 80x30
  116. [ 0.000122] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
  117. [ 0.000139] pid_max: default: 32768 minimum: 301
  118. [ 0.000244] Mount-cache hash table entries: 512
  119. [ 0.000640] CPU: Testing write buffer coherency: ok
  120. [ 0.000829] Setting up static identity map for 0x4034b278 - 0x4034b2d0
  121. [ 0.001317] devtmpfs: initialized
  122. [ 0.002729] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
  123. [ 0.002895] pinctrl core: initialized pinctrl subsystem
  124. [ 0.003267] NET: Registered protocol family 16
  125. [ 0.003593] DMA: preallocated 128 KiB pool for atomic coherent allocations
  126. [ 0.003636] script_sysfs_init success
  127. [ 0.003664] sunxi_dump_init success
  128. [ 0.004255] gpiochip_add: registered GPIOs 0 to 223 on device: sunxi-pinctrl
  129. [ 0.004957] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
  130. [ 0.005228] gpiochip_add: registered GPIOs 1024 to 1031 on device: axp-pinctrl
  131. [ 0.006154] persistent_ram: uncorrectable error in header
  132. [ 0.006167] persistent_ram: no valid data in buffer (sig = 0x00000003)
  133. [ 0.011677] console [ram-1] enabled
  134. [ 0.012022] [sunxi-module]: [sunxi-module.0] probe success
  135. [ 0.012181] axp driver uning configuration failed(741)
  136. [ 0.012338] axp driver uning configuration failed(747)
  137. [ 0.012433] axp driver uning configuration failed(803)
  138. [ 0.012587] axp driver uning configuration failed(810)
  139. [ 0.012672] axp driver uning configuration failed(817)
  140. [ 0.012827] axp driver uning configuration failed(824)
  141. [ 0.012912] axp driver uning configuration failed(831)
  142. [ 0.013068] axp driver uning configuration failed(838)
  143. [ 0.013153] axp driver uning configuration failed(844)
  144. [ 0.013402] script config pll_isp to 360 Mhz
  145. [ 0.013503] Not Found clk pll_video in script
  146. [ 0.013592] script config pll_ve to 360 Mhz
  147. [ 0.013755] Not Found clk pll_periph0 in script
  148. [ 0.013840] Not Found clk pll_de in script
  149. [ 0.013923] sunxi_default_clk_init
  150. [ 0.014076] try to set pll6ahb1 to 200000000
  151. [ 0.014162] Error not get clk pll6ahb1
  152. [ 0.014249] Error not get clk pll6ahb1try to set ahb1 to 200000000
  153. [ 0.014491] try to set apb1 to 100000000
  154. [ 0.014835] ===fe3o4==== sunxi_root_procfs_attach ret:0
  155. [ 0.017904] bio: create slab <bio-0> at 0
  156. [ 0.018195] pwm module init!
  157. [ 0.019937] SCSI subsystem initialized
  158. [ 0.020203] usbcore: registered new interface driver usbfs
  159. [ 0.020342] usbcore: registered new interface driver hub
  160. [ 0.020606] usbcore: registered new device driver usb
  161. [ 0.020796] twi_chan_cfg()341 - [twi0] has no twi_speed!
  162. [ 0.020955] twi_chan_cfg()352 - [twi0] has no twi_regulator.
  163. [ 0.021040] twi_chan_cfg()341 - [twi1] has no twi_speed!
  164. [ 0.021194] twi_chan_cfg()352 - [twi1] has no twi_regulator.
  165. [ 0.021900] axp20_board 0-0034: AXP (CHIP ID: 0x41) detected
  166. [ 0.021900] Linux video capture interface: v2.00
  167. [ 0.021900] gpiochip_add: gpios 1024..1028 (axp_pin) failed to register
  168. [ 0.021900] axp pinctrl used,skip
  169. [ 0.021900] Advanced Linux Sound Architecture Driver Version 1.0.25.
  170. [ 0.030830] cfg80211: Calling CRDA to update world regulatory domain
  171. [ 0.031313] Switching to clocksource arch_sys_counter
  172. [ 0.038702] NET: Registered protocol family 2
  173. [ 0.039066] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  174. [ 0.039453] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
  175. [ 0.039667] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
  176. [ 0.039851] TCP: Hash tables configured (established 4096 bind 4096)
  177. [ 0.039939] TCP: reno registered
  178. [ 0.039939] UDP hash table entries: 256 (order: 0, 4096 bytes)
  179. [ 0.039939] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  180. [ 0.039939] NET: Registered protocol family 1
  181. [ 0.039939] Unpacking initramfs...
  182. [ 0.051485] Freeing initrd memory: 224K
  183. [ 0.051848] [pm]aw_pm_init!
  184. [ 0.051937] standby_mode = 1.
  185. [ 0.052020] wakeup src cnt is : 3.
  186. [ 0.052109] pmu name: pmu1_para .
  187. [ 0.052266] pmu1_enable = 0x1.
  188. [ 0.052351] pmux_id = 0x1.
  189. [ 0.052435] pmu name: pmu2_para .
  190. [ 0.052519] config_pmux_para: script_parser_fetch err.
  191. [ 0.052673] pmu2_enable = 0x0.
  192. [ 0.052766] add_sys_pwr_dm: get ldo name failed
  193. [ 0.052922] add_sys_pwr_dm: get ldo name failed
  194. [ 0.053288] add_sys_pwr_dm: get ldo name failed
  195. [ 0.053382] add_sys_pwr_dm: get ldo name failed
  196. [ 0.053538] add_sys_pwr_dm: get ldo name failed
  197. [ 0.053624] add_sys_pwr_dm: get ldo name failed
  198. [ 0.054015] add_sys_pwr_dm: get ldo name failed
  199. [ 0.054332] after inited: sys_mask config = 0x4810.
  200. [ 0.054420] config_dynamic_standby: script_parser_fetch err.
  201. [ 0.054574] dynamic_standby enalbe = 0x0.
  202. [ 0.054703] sunxi_reg_init enter
  203. [ 0.056254] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  204. [ 0.056379] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
  205. [ 0.056683] msgmni has been set to 72
  206. [ 0.057467] io scheduler noop registered
  207. [ 0.057560] io scheduler deadline registered
  208. [ 0.057773] io scheduler cfq registered (default)
  209. [ 0.058190] [DISP]disp_module_init
  210. [ 0.058575] cmdline,disp=
  211. [ 0.059145] rotation_sw module is config as no used
  212. [ 0.059249] [DISP] disp_get_rotation_sw,line:128:disp 0 out of range? g_rot_sw=0
  213. [ 0.059418] [DISP] disp_init_connections,line:289:NULL pointer: 0, 0
  214. [ 0.070833] [DISP] disp_sys_power_enable,line:387:some error happen, fail to get regulator
  215. [ 0.071197] [DISP]disp_module_init finish
  216. [ 0.071504] sw_uart_get_devinfo()1503 - uart0 has no uart_regulator.
  217. [ 0.071673] sw_uart_get_devinfo()1503 - uart2 has no uart_regulator.
  218. [ 0.072154] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
  219. [ 0.072534] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI
  220. [ 0.072697] sw_uart_pm()890 - uart2 clk is already enable
  221. [ 0.072791] sw_console_setup()1233 - console setup baud 115200 parity n bits 8, flow n
  222. [ 0.266075] console [ttyS2] enabled
  223. [ 0.948931] sunxi_spi_chan_cfg()1376 - [spi-0] has no spi_regulator.
  224. [ 0.956667] spi spi0: master is unqueued, this is deprecated
  225. [ 0.963175] m25p_probe()966 - Use the Dual Mode Read.
  226. [ 0.968929] NorFlash ID: 0xb4018 - 0xb40
  227. [ 0.973464] m25p80 spi0.0: unrecognized JEDEC id 0b4018
  228. [ 0.980538] Failed to alloc md5
  229. [ 0.984205] eth0: Use random mac address
  230. [ 0.988674] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  231. [ 1.016104] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  232. [ 1.025205] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1
  233. [ 1.033846] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
  234. [ 1.060031] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
  235. [ 1.067329] hub 1-0:1.0: USB hub found
  236. [ 1.071614] hub 1-0:1.0: 1 port detected
  237. [ 1.076533] sunxi-ehci sunxi-ehci.1: remove, state 1
  238. [ 1.082151] usb usb1: USB disconnect, device number 1
  239. [ 1.372002] sunxi-ehci sunxi-ehci.1: USB bus 1 deregistered
  240. [ 1.388429] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  241. [ 1.415466] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
  242. [ 1.424150] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 1
  243. [ 1.432740] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400
  244. [ 1.494537] hub 1-0:1.0: USB hub found
  245. [ 1.498856] hub 1-0:1.0: 1 port detected
  246. [ 1.503647] sunxi-ohci sunxi-ohci.1: remove, state 1
  247. [ 1.509239] usb usb1: USB disconnect, device number 1
  248. [ 1.515468] sunxi-ohci sunxi-ohci.1: USB bus 1 deregistered
  249. [ 1.531841] Initializing USB Mass Storage driver...
  250. [ 1.537473] usbcore: registered new interface driver usb-storage
  251. [ 1.544227] USB Mass Storage support registered.
  252. [ 1.549532] usbcore: registered new interface driver libusual
  253. [ 1.556037] usbcore: registered new interface driver ums-alauda
  254. [ 1.562785] usbcore: registered new interface driver ums-cypress
  255. [ 1.569558] usbcore: registered new interface driver ums-datafab
  256. [ 1.576397] usbcore: registered new interface driver ums_eneub6250
  257. [ 1.583361] usbcore: registered new interface driver ums-freecom
  258. [ 1.590210] usbcore: registered new interface driver ums-isd200
  259. [ 1.596871] usbcore: registered new interface driver ums-jumpshot
  260. [ 1.603814] usbcore: registered new interface driver ums-karma
  261. [ 1.610459] usbcore: registered new interface driver ums-onetouch
  262. [ 1.617330] usbcore: registered new interface driver ums-realtek
  263. [ 1.624177] usbcore: registered new interface driver ums-sddr09
  264. [ 1.630857] usbcore: registered new interface driver ums-sddr55
  265. [ 1.637610] usbcore: registered new interface driver ums-usbat
  266. [ 1.644442] file system registered
  267. [ 1.649531] android_usb gadget: Mass Storage Function, version: 2009/09/11
  268. [ 1.657373] android_usb gadget: Number of LUNs=1
  269. [ 1.662583] lun0: LUN: removable file: (no medium)
  270. [ 1.668484] android_usb gadget: android_usb ready
  271. [ 1.673924] sunxikbd_script_init: key para not found, used default para.
  272. [ 1.682451] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0
  273. [ 1.690126] sunxi cedar version 0.1
  274. [ 1.694201] [cedar]: install start!!!
  275. [ 1.698543] [cedar]: install end!!!
  276. [ 1.709417] pmu_pekoff_time = 6000
  277. [ 1.713366] pmu_pekoff_en = 1
  278. [ 1.716726] pmu_peklong_time = 1500
  279. [ 1.720670] pmu_pekon_time = 1000
  280. [ 1.724501] pmu_pwrok_time = 64
  281. [ 1.728055] pmu_pwrnoe_time = 2000
  282. [ 1.731903] pmu_hot_shutdown = 1
  283. [ 1.736383] POWER20_PEK_SET:2234-->0x9d
  284. [ 1.741205] POWER20_PEK_SET:2245-->0x9d
  285. [ 1.745942] POWER20_PEK_SET:2254-->0x9d
  286. [ 1.750689] POWER20_PEK_SET:2265-->0x9d
  287. [ 1.755498] POWER20_PEK_SET:2277-->0x9d
  288. [ 1.760244] POWER20_HOTOVER_CTL:2286-->0x25
  289. [ 1.772156] sunxi_wdt_init_module: sunxi WatchDog Timer Driver v1.0
  290. [ 1.779450] sunxi_wdt_probe: devm_ioremap return wdt_reg 0xf1c20ca0, res->start 0x01c20ca0, res->end 0x01c20cbf
  291. [ 1.790814] sunxi_wdt_probe: initialized (g_timeout=16s, g_nowayout=0)
  292. [ 1.798479] wdt_enable, write reg 0xf1c20cb8 val 0x00000000
  293. [ 1.804760] wdt_set_tmout, write 0x000000b0 to mode reg 0xf1c20cb8, actual timeout 16 sec
  294. [ 1.814116] [cpu_freq] ERR:get cpu extremity frequency from sysconfig failed, use max_freq
  295. [ 1.823654] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.114 2015-6-2 10:21) Compiled in Jun 30 2020 at 14:13:52
  296. [ 1.835145] [mmc]: get mmc0's sdc_power failed
  297. [ 1.840240] [mmc]: get mmc1's sdc_power failed
  298. [ 1.845252] [mmc]: MMC host used card: 0x3, boot card: 0x2, io_card 2
  299. [ 1.853221] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  300. [ 1.864276] [mmc]: sdc1 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  301. [ 1.874466] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  302. [ 1.884415] [mmc]: sdc1 power_supply is null
  303. [ 1.893184] sunxi_leds_fetch_sysconfig_para leds is not used in config
  304. [ 1.900600] =========script_get_err============
  305. [ 1.905889] usbcore: registered new interface driver usbhid
  306. [ 1.912257] usbhid: USB HID core driver
  307. [ 1.916602] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  308. [ 1.927388] ashmem: initialized
  309. [ 1.931107] logger: created 256K log 'log_main'
  310. [ 1.936370] logger: created 32K log 'log_events'
  311. [ 2.940010] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  312. [ 3.940008] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  313. [ 4.940007] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  314. [ 4.949483] logger: created 32K log 'log_radio'
  315. [ 4.954833] logger: created 32K log 'log_system'
  316. [ 4.960082] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  317. [ 4.976656] [audiocodec] mic1_mic3_used type err!
  318. [ 4.982886] asoc: sndcodec <-> sunxi-codec mapping ok
  319. [ 5.980012] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  320. [ 6.980008] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  321. [ 7.980007] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  322. [ 7.990913] TCP: cubic registered
  323. [ 7.994702] NET: Registered protocol family 17
  324. [ 7.999998] ThumbEE CPU extension supported.
  325. [ 8.004857] Registering SWP/SWPB emulation handler
  326. [ 8.012767] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  327. [ 9.020012] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  328. [ 10.020009] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  329. [ 11.020007] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  330. [ 11.030062] *******************Try sdio*******************
  331. [ 11.036292] *******************Try sd *******************
  332. [ 11.042363] *******************Try mmc*******************
  333. [ 11.048494] [mmc]: sdc1 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  334. [ 12.050009] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  335. [ 13.050007] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  336. [ 14.050007] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  337. [ 14.059116] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  338. [ 14.068966] sunxi_i2c_do_xfer()990 - [i2c0] xfer timeout (dev addr:0x34)
  339. [ 14.076566] axp20_board 0-0034: failed reading from 0x03
  340. [ 14.083301] [mmc]: sdc1 power_supply is null
  341. [ 14.089616] sunxi-rtc sunxi-rtc: setting system clock to 1970-01-01 00:00:16 UTC (16)
  342. [ 14.099599] [mmc]: sdc1 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  343. [ 14.111813] ****************Set_Rset_Cap=100***********
  344. [ 14.118007] [rf_pm]: Did not config module_power0 in sys_config
  345. [ 14.124681] [rf_pm]: Did not config module_power1 in sys_config
  346. [ 14.131412] [rf_pm]: Did not config module_power2 in sys_config
  347. [ 14.138048] [rf_pm]: Did not config module_power3 in sys_config
  348. [ 14.144762] [rf_pm]: mod has no chip_en gpio
  349. [ 14.149566] [rf_pm]: failed to fetch lpo_use_apclk
  350. [ 14.155023] [rf_pm]: regulator on.
  351. [ 14.158998] [mmc]: sdc1 power_supply is null
  352. [ 14.165740]
  353. [ 14.165745] ===========Capacity calibration finished============
  354. [ 14.174488]
  355. [ 14.174491] ============ Battery capacity = 0 ============
  356. [ 14.183128] Division by zero in kernel.
  357. [ 14.187449] Backtrace:
  358. [ 14.190342] [<c0013490>] (dump_backtrace+0x0/0x110) from [<c03454b8>] (dump_stack+0x18/0x1c)
  359. [ 14.199846] r6:c2659000 r5:00000064 r4:c26591cc r3:c049a780
  360. [ 14.206614] [<c03454a0>] (dump_stack+0x0/0x1c) from [<c00135b8>] (__div0+0x18/0x20)
  361. [ 14.215199] [<c00135a0>] (__div0+0x0/0x20) from [<c011ff90>] (Ldiv0+0x8/0x10)
  362. [ 14.223281] [<c025b5d4>] (axp_charging_monitor+0x0/0x12bc) from [<c004238c>] (process_one_work+0x1e0/0x338)
  363. [ 14.234243] [<c00421ac>] (process_one_work+0x0/0x338) from [<c004316c>] (worker_thread+0x1c0/0x2c8)
  364. [ 14.244439] [<c0042fac>] (worker_thread+0x0/0x2c8) from [<c0046a1c>] (kthread+0x94/0xa0)
  365. [ 14.253499] [<c0046988>] (kthread+0x0/0xa0) from [<c0031d20>] (do_exit+0x0/0x660)
  366. [ 14.261945] r6:c0031d20 r5:c0046988 r4:c2427ed0
  367. [ 14.267401] [mmc]: sdc1 set ios: clk 300000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  368. [ 14.282740] [wifi_pm]: wifi gpio init is OK !!
  369. [ 14.287891] [rfkill]: init no bt used in configuration
  370. [ 14.293683] ALSA device list:
  371. [ 14.297055] #0: audiocodec
  372. [ 14.300570] ****************Set_Rset_Cap=100***********
  373. [ 14.306916] Freeing init memory: 140K
  374. [ 14.312597] init: skipping insecure file '/default.prop'
  375. [ 14.318772] init: skipping insecure file '/init.rc'
  376. [ 14.324624] init: /init.rc: 134: invalid option 'root'
  377. [ 14.330643] init: skipping insecure file '/init.sun8i.rc'
  378. [ 14.336806] init: /init.sun8i.rc: 57: invalid option 'root'
  379. [ 14.343222] init: /init.sun8i.rc: 72: invalid option 'root'
  380. [ 14.349507] init: /init.sun8i.rc: 77: invalid option 'root'
  381. [ 14.355877] init: skipping insecure file 'init.sun8i.usb.rc'
  382. [ 14.362697] init: command 'loglevel' r=0
  383. [ 14.367194] init: command 'export' r=0
  384. [ 14.372604] init: skipping insecure file '/ueventd.rc'
  385. [ 14.378558] init: skipping insecure file '/ueventd.sun8i.rc'
  386. [ 14.385115] init: command 'export' r=0
  387. [ 14.389356] init: command 'export' r=0
  388. [ 14.398105] init: command 'export' r=0
  389. [ 14.410248] init: command 'export' r=0
  390. [ 14.414509] init: command 'export' r=0
  391. [ 14.418770] init: command 'export' r=0
  392. [ 15.420012] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  393. [ 16.420008] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  394. [ 17.420007] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  395. [ 17.440270] [mmc]: sdc1 set ios: clk 300000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  396. [ 17.450687] init: command 'symlink' r=0
  397. [ 17.455045] init: command 'symlink' r=0
  398. [ 17.459422] init: command 'symlink' r=0
  399. [ 18.470013] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  400. [ 19.470009] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  401. [ 20.470008] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  402. [ 20.483521] init: command 'mkdir' r=0
  403. [ 20.487721] init: command 'mkdir' r=0
  404. [ 20.491969] init: command 'mkdir' r=0
  405. [ 20.496192] init: command 'mkdir' r=-2
  406. [ 20.500482] init: processing action 0x47ac48 (init)
  407. [ 20.506062] init: command 'write' r=0
  408. [ 20.510353] init: command 'write' r=0
  409. [ 20.514523] init: command 'write' r=0
  410. [ 20.518704] init: command 'write' r=0
  411. [ 20.522952] init: command 'export' r=0
  412. [ 20.527188] init: processing action 0x4790d0 (early-fs)
  413. [ 20.533193] init: command 'mkdir' r=0
  414. [ 20.537359] init: command 'mkdir' r=0
  415. [ 20.541550] init: command 'mkdir' r=0
  416. [ 20.545691] init: processing action 0x47c098 (console_init)
  417. [ 20.552237] init: command 'console_init' r=0
  418. [ 20.557063] init: processing action 0x479450 (fs)
  419. [ 20.565053] [mmc]: sdc1 set ios: clk 300000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  420. [ 21.570012] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  421. [ 22.570008] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  422. [ 23.570007] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  423. [ 23.585035] *******************Try sdio*******************
  424. [ 23.591349] *******************Try sd *******************
  425. [ 23.597486] *******************Try mmc*******************
  426. [ 23.603568] [mmc]: sdc1 set ios: clk 300000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  427. [ 24.610010] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  428. [ 25.610007] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  429. [ 26.610007] [mmc]: *** sunxi_mci_update_clk(L492): update clock timeout, fatal error!!!
  430. [ 26.619374] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  431. [ 26.629413] [mmc]: sdc1 power_supply is null
  432. [ 26.634289] init: command 'wait' r=-1
  433. [ 26.639575] [mmc]: sdc1 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  434. [ 26.649823] init: command 'setupfs' r=1
  435. [ 26.654340] init: out of loopback devices source = /dev/block/mmcblk0p5
  436. [ 26.661772] [mmc]: sdc1 power_supply is null
  437. [ 26.667884] init: out of loopback devices target = /system
  438. [ 26.674062] init: out of loopback devices system = squashfs
  439. [ 26.680399] [mmc]: sdc1 set ios: clk 200000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  440. [ 26.690626] init: out of loopback devices options = (null)
  441. [ 26.697039] init: do_mount errno=2
  442. [ 26.701135] init: command 'mount' r=-1
  443. [ 26.705717] ****************Set_Rset_Cap=100***********
  444. [ 26.721635] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 52, RTO !!
  445. [ 26.731592] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 52, RTO !!
  446. [ 26.739880] [mmc]: sdc1 set ios: clk 200000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  447. [ 26.753075] [mmc]: sdc1 set ios: clk 200000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  448. [ 26.766142] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 1 err, cmd 8, RTO !!
  449. [ 26.774428] *******************Try sdio*******************
  450. [ 26.781243] [mmc]: sdc1 set ios: clk 200000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  451. [ 26.810305] [mmc]: sdc1 set ios: clk 200000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
  452. [ 26.820686] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
  453. [ 26.831163] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B
  454. [ 26.842243] mmc0: new high speed SDIO card at address 0001
  455. [ 26.848845] *******************sdio init ok*******************
  456. [ 29.723047] Division by zero in kernel.
  457. [ 29.727467] Backtrace:
  458. [ 29.730365] [<c0013490>] (dump_backtrace+0x0/0x110) from [<c03454b8>] (dump_stack+0x18/0x1c)
  459. [ 29.739868] r6:c2659000 r5:00000064 r4:c26591cc r3:c049a780
  460. [ 29.746570] [<c03454a0>] (dump_stack+0x0/0x1c) from [<c00135b8>] (__div0+0x18/0x20)
  461. [ 29.755225] [<c00135a0>] (__div0+0x0/0x20) from [<c011ff90>] (Ldiv0+0x8/0x10)
  462. [ 29.763234] [<c025b5d4>] (axp_charging_monitor+0x0/0x12bc) from [<c004238c>] (process_one_work+0x1e0/0x338)
  463. [ 29.774195] [<c00421ac>] (process_one_work+0x0/0x338) from [<c004316c>] (worker_thread+0x1c0/0x2c8)
  464. [ 29.784394] [<c0042fac>] (worker_thread+0x0/0x2c8) from [<c0046a1c>] (kthread+0x94/0xa0)
  465. [ 29.793534] [<c0046988>] (kthread+0x0/0xa0) from [<c0031d20>] (do_exit+0x0/0x660)
  466. [ 29.801918] r6:c0031d20 r5:c0046988 r4:c2427ed0
  467. [ 31.008419] init: command 'wait' r=-1
  468. [ 31.012595] init: out of loopback devices source = /dev/block/mmcblk0p6
  469. [ 31.020090] init: out of loopback devices target = /data
  470. [ 31.026054] init: out of loopback devices system = jffs2
  471. [ 31.032092] init: out of loopback devices options = (null)
  472. [ 31.038333] init: do_mount errno=2
  473. [ 31.042415] init: command 'mount' r=-1
  474. [ 31.046660] init: out of loopback devices source = none
  475. [ 31.052568] init: out of loopback devices target = /sys/kernel/debug/
  476. [ 31.059855] init: out of loopback devices system = debugfs
  477. [ 31.066022] init: out of loopback devices options = (null)
  478. [ 31.072341] init: command 'mount' r=0
  479. [ 31.076518] init: processing action 0x479558 (post-fs)
  480. [ 31.087427] init: out of loopback devices source = rootfs
  481. [ 31.093510] init: out of loopback devices target = /
  482. [ 31.099158] init: out of loopback devices system = rootfs
  483. [ 31.105231] init: out of loopback devices options = (null)
  484. [ 31.111430] init: command 'mount' r=0
  485. [ 31.115670] init: processing action 0x4795b8 (post-fs-data)
  486. [ 31.122028] init: command 'chown' r=0
  487. [ 31.126267] init: command 'chmod' r=0
  488. [ 31.130447] init: command 'chmod' r=0
  489. [ 31.134635] init: command 'mkdir' r=0
  490. [ 31.138858] init: command 'restorecon' r=0
  491. [ 31.143547] init: command 'mkdir' r=0
  492. [ 31.147712] init: command 'mkdir' r=0
  493. [ 31.151959] init: command 'mkdir' r=0
  494. [ 31.156128] init: command 'mkdir' r=0
  495. [ 31.160300] init: command 'chown' r=0
  496. [ 31.164527] init: command 'mkdir' r=0
  497. [ 31.168664] init: processing action 0x47a938 (post-fs-data)
  498. [ 31.174954] init: command 'insmod' r=-1
  499. [ 31.179362] init: command 'insmod' r=-1
  500. [ 31.183711] init: command 'insmod' r=-1
  501. [ 31.188056] init: command 'insmod' r=-1
  502. [ 31.192471] init: command 'insmod' r=-1
  503. [ 31.196806] init: command 'insmod' r=-1
  504. [ 31.201150] init: command 'insmod' r=-1
  505. [ 31.205562] init: command 'insmod' r=-1
  506. [ 31.209904] init: command 'insmod' r=-1
  507. [ 31.214251] init: command 'insmod' r=-1
  508. [ 31.218656] init: command 'insmod' r=-1
  509. [ 31.223000] init: processing action 0x47c0e0 (property_service_init)
  510. [ 31.230379] init: Created socket '/dev/socket/property_service' with mode '666', user '0', group '0'
  511. [ 31.240640] init: command 'property_service_init' r=0
  512. [ 31.246400] init: processing action 0x47c128 (signal_init)
  513. [ 31.252612] init: command 'signal_init' r=0
  514. [ 31.257416] init: processing action 0x47c170 (check_startup)
  515. [ 31.263816] init: command 'check_startup' r=0
  516. [ 31.268798] init: processing action 0x4797c8 (boot)
  517. [ 31.274632] init: command 'ifup' r=0
  518. [ 31.278768] init: command 'hostname' r=0
  519. [ 31.283342] init: command 'domainname' r=0
  520. [ 31.288085] init: command 'setrlimit' r=0
  521. [ 31.292713] init: command 'chown' r=0
  522. [ 31.296948] init: cannot find '/system/bin/servicemanager', disabling 'servicemanager'
  523. [ 31.305846] init: cannot find '/system/bin/vold', disabling 'vold'
  524. [ 31.312867] init: cannot find '/system/bin/startup_music', disabling 'startupSound'
  525. [ 31.321514] init: cannot find '/system/bin/dragonboard', disabling 'dragonboard'
  526. [ 31.329798] init: command 'class_start' r=0
  527. [ 31.334603] init: cannot find '/system/bin/debuggerd', disabling 'debuggerd'
  528. [ 31.342513] init: cannot find '/system/bin/mediaserver', disabling 'media'
  529. [ 31.350307] init: starting 'adbd'
  530. [ 31.354364] init: cannot find '/system/bin/dhcpcd', disabling 'dhcpcd_eth0'
  531. [ 31.362618] init: Created socket '/dev/socket/adbd' with mode '660', user '1000', group '1000'
  532. [ 31.372427] init: cannot find '/system/bin/dnsmasq', disabling 'dnsmasq_eth0'
  533. [ 31.386695] adb_open
  534. [ 31.389671] init: command 'class_start' r=0
  535. [ 31.394564] init: processing action 0x47aac8 (boot)
  536. [ 31.400091] init: command 'setprop' r=0
  537. [ 31.404499] init: processing action 0x47c1b8 (queue_property_triggers)
  538. [ 31.411864] init: command 'queue_property_triggers' r=0
  539. [ 31.417810] init: processing action 0x479aa8 (property:ro.debuggable=1)
  540. [ 31.425278] init: cannot find '/system/bin/sh', disabling 'console'
  541. [ 31.432386] init: command 'start' r=0
  542. [ 32.813052] Division by zero in kernel.
  543. [ 32.817395] Backtrace:
  544. [ 32.820361] [<c0013490>] (dump_backtrace+0x0/0x110) from [<c03454b8>] (dump_stack+0x18/0x1c)
  545. [ 32.829796] r6:c2659000 r5:00000064 r4:c26591cc r3:c049a780
  546. [ 32.836567] [<c03454a0>] (dump_stack+0x0/0x1c) from [<c00135b8>] (__div0+0x18/0x20)
  547. [ 32.845218] [<c00135a0>] (__div0+0x0/0x20) from [<c011ff90>] (Ldiv0+0x8/0x10)
  548. [ 32.853230] [<c025b5d4>] (axp_charging_monitor+0x0/0x12bc) from [<c004238c>] (process_one_work+0x1e0/0x338)
  549. [ 32.864197] [<c00421ac>] (process_one_work+0x0/0x338) from [<c004316c>] (worker_thread+0x1c0/0x2c8)
  550. [ 32.874402] [<c0042fac>] (worker_thread+0x0/0x2c8) from [<c0046a1c>] (kthread+0x94/0xa0)
  551. [ 32.888541] [<c0046988>] (kthread+0x0/0xa0) from [<c0031d20>] (do_exit+0x0/0x660)
  552. [ 32.896918] r6:c0031d20 r5:c0046988 r4:c2427ed0
  553. [ 35.913040] Division by zero in kernel.
  554. [ 35.917375] Backtrace:
  555. [ 35.920268] [<c0013490>] (dump_backtrace+0x0/0x110) from [<c03454b8>] (dump_stack+0x18/0x1c)
  556. [ 35.929780] r6:c2659000 r5:00000064 r4:c26591cc r3:c049a780
  557. [ 35.936476] [<c03454a0>] (dump_stack+0x0/0x1c) from [<c00135b8>] (__div0+0x18/0x20)
  558. [ 35.945134] [<c00135a0>] (__div0+0x0/0x20) from [<c011ff90>] (Ldiv0+0x8/0x10)
  559. [ 35.953214] [<c025b5d4>] (axp_charging_monitor+0x0/0x12bc) from [<c004238c>] (process_one_work+0x1e0/0x338)
  560. [ 35.964179] [<c00421ac>] (process_one_work+0x0/0x338) from [<c004316c>] (worker_thread+0x1c0/0x2c8)
  561. [ 35.974301] [<c0042fac>] (worker_thread+0x0/0x2c8) from [<c0046a1c>] (kthread+0x94/0xa0)
  562. [ 35.983429] [<c0046988>] (kthread+0x0/0xa0) from [<c0031d20>] (do_exit+0x0/0x660)
  563. [ 35.991873] r6:c0031d20 r5:c0046988 r4:c2427ed0
  564. [ 39.003046] Division by zero in kernel.
  565. [ 39.007449] Backtrace:
  566. [ 39.010340] [<c0013490>] (dump_backtrace+0x0/0x110) from [<c03454b8>] (dump_stack+0x18/0x1c)
  567. [ 39.019776] r6:c2659000 r5:00000064 r4:c26591cc r3:c049a780
  568. [ 39.026538] [<c03454a0>] (dump_stack+0x0/0x1c) from [<c00135b8>] (__div0+0x18/0x20)
  569. [ 39.035191] [<c00135a0>] (__div0+0x0/0x20) from [<c011ff90>] (Ldiv0+0x8/0x10)
  570. [ 39.043205] [<c025b5d4>] (axp_charging_monitor+0x0/0x12bc) from [<c004238c>] (process_one_work+0x1e0/0x338)
  571. [ 39.054173] [<c00421ac>] (process_one_work+0x0/0x338) from [<c004316c>] (worker_thread+0x1c0/0x2c8)
  572. [ 39.064370] [<c0042fac>] (worker_thread+0x0/0x2c8) from [<c0046a1c>] (kthread+0x94/0xa0)
  573. [ 39.073504] [<c0046988>] (kthread+0x0/0xa0) from [<c0031d20>] (do_exit+0x0/0x660)
  574. [ 39.081880] r6:c0031d20 r5:c0046988 r4:c2427ed0
  575. [ 42.093043] Division by zero in kernel.
  576. [ 42.097381] Backtrace:
  577. [ 42.100265] [<c0013490>] (dump_backtrace+0x0/0x110) from [<c03454b8>] (dump_stack+0x18/0x1c)
  578. [ 42.109767] r6:c2659000 r5:00000064 r4:c26591cc r3:c049a780
  579. [ 42.116539] [<c03454a0>] (dump_stack+0x0/0x1c) from [<c00135b8>] (__div0+0x18/0x20)
  580. [ 42.125123] [<c00135a0>] (__div0+0x0/0x20) from [<c011ff90>] (Ldiv0+0x8/0x10)
  581. [ 42.133205] [<c025b5d4>] (axp_charging_monitor+0x0/0x12bc) from [<c004238c>] (process_one_work+0x1e0/0x338)
  582. [ 42.144179] [<c00421ac>] (process_one_work+0x0/0x338) from [<c004316c>] (worker_thread+0x1c0/0x2c8)
  583. [ 42.154387] [<c0042fac>] (worker_thread+0x0/0x2c8) from [<c0046a1c>] (kthread+0x94/0xa0)
  584. [ 42.163455] [<c0046988>] (kthread+0x0/0xa0) from [<c0031d20>] (do_exit+0x0/0x660)
  585. [ 42.171903] r6:c0031d20 r5:c0046988 r4:c2427ed0
  586. [ 45.188067] Division by zero in kernel.
  587. [ 45.192490] Backtrace:
  588. [ 45.195370] [<c0013490>] (dump_backtrace+0x0/0x110) from [<c03454b8>] (dump_stack+0x18/0x1c)
  589. [ 45.204904] r6:c2659000 r5:00000064 r4:c26591cc r3:c049a780
  590. [ 45.211597] [<c03454a0>] (dump_stack+0x0/0x1c) from [<c00135b8>] (__div0+0x18/0x20)
  591. [ 45.220263] [<c00135a0>] (__div0+0x0/0x20) from [<c011ff90>] (Ldiv0+0x8/0x10)
  592. [ 45.228275] [<c025b5d4>] (axp_charging_monitor+0x0/0x12bc) from [<c004238c>] (process_one_work+0x1e0/0x338)
  593. [ 45.239254] [<c00421ac>] (process_one_work+0x0/0x338) from [<c004316c>] (worker_thread+0x1c0/0x2c8)
  594. [ 45.249460] [<c0042fac>] (worker_thread+0x0/0x2c8) from [<c0046a1c>] (kthread+0x94/0xa0)
  595. [ 45.258604] [<c0046988>] (kthread+0x0/0xa0) from [<c0031d20>] (do_exit+0x0/0x660)
  596. [ 45.266992] r6:c0031d20 r5:c0046988 r4:c2427ed0
  597. [
  598.  
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!