2018-09-19 10:30:04  ★ Vincent DeLuca sets his toolbox down on the ground, taking a knee to open it.

2018-09-19 10:30:39  ★ Vincent DeLuca takes out a screwdriver and pushes himself up and unscrews the bike's seat in order

2018-09-19 10:30:45  ★ to reveal the battery.      ((Vincent DeLuca))

2018-09-19 10:30:54  ★ Vincent DeLuca unscrews the clamps on the terminals.

2018-09-19 10:31:08  ★ Vincent DeLuca disconnects the negative terminal and waits around thirty seconds

2018-09-19 10:31:17  ★ Vincent DeLuca removes the positive terminal afterwards.

2018-09-19 10:31:33  ★ Vincent DeLuca pulls the battery out of its place, putting it on the ground.

2018-09-19 10:32:09  ★ Vincent DeLuca takes out a socket wrench.

2018-09-19 10:32:12  ★ Vincent DeLuca loosens the two Allen head, pinch bolts that hold the upper triple tree to the front forks.

2018-09-19 10:33:23  ★ Vincent DeLuca unscrews the bolts that hold the steering damper up on the upper triple tree, -..

2018-09-19 10:33:38  ★ leaving the opposite end of the steering damper attached to the frame.      ((Vincent DeLuca))

2018-09-19 10:34:00  ★ Vincent DeLuca uses his ratchet to remove the 32 mm nut and washer that hold the upper triple tree to the

2018-09-19 10:34:11  ★ -.. steering stem, and then pulls the upper triple tree and off the stem and fork.      ((Vincent DeLuca))

2018-09-19 10:34:37  ★ Vincent DeLuca traces the original wiring until he locates the connector in your motorcycle.

2018-09-19 10:34:46  ★ Vincent DeLuca disconnects the connector by separating the ignition from its wiring harness.

2018-09-19 10:35:12  ★ Vincent DeLuca removes the entire upper triple tree and ignition switch from your motorcycle and lays it down

2018-09-19 10:35:15  ★ on the floor.      ((Vincent DeLuca))

2018-09-19 10:35:41  ★ Vincent DeLuca set ignition switch facing down and locate the two bolts that hold it to the underside of the

2018-09-19 10:35:45  ★ triple tree.      ((Vincent DeLuca))

2018-09-19 10:36:01  Vincent DeLuca: (( locates* ))

2018-09-19 10:36:21  ★ Vincent DeLuca removes the ignition switch from the upper triple clamp.

2018-09-19 10:36:34  ★ Vincent DeLuca takes a box out of his bag, with new ignition swich in it.

2018-09-19 10:36:56  ★ Vincent DeLuca opens the box and takes out the ignition switch before putting it in the upper tripple clamp.

2018-09-19 10:37:13  ★ Vincent DeLuca secures it with the two bolts that hold it to the underside of the triple tree.

2018-09-19 10:37:47  ★ Vincent DeLuca carries the upper triple tree and inserts it back in its original place within the motorcycle.

2018-09-19 10:38:13  ★ Vincent DeLuca plugs the connector of the wiring harness into the ignition.

2018-09-19 10:38:43  ★ Vincent DeLuca secures the 32 mm nut that hold the upper triple tree to the steering stem

2018-09-19 10:39:03  ★ Vincent DeLuca after putting the upper triple treein the stem and fork.

2018-09-19 10:39:25  ★ Vincent DeLuca screws the bolts that hold up the steering damper up on the upper triple tree.

2018-09-19 10:39:46  ★ Vincent DeLuca secures the two allen head pinch bolts that hold the upper triple tree to the front forks.

2018-09-19 10:40:03  ★ Vincent DeLuca picks up the battery and inserts it into place before connecting the positive terminal and

2018-09-19 10:40:08  ★ securing the clamp on it.      ((Vincent DeLuca))

2018-09-19 10:40:25  ★ Vincent DeLuca connects the negative terminal afterwards, securing it as well.

2018-09-19 10:40:41  ★ Vincent DeLuca places the seat back on the motorcycle and binds it with the screws.

2018-09-19 10:40:56  ★ Vincent DeLuca takes out the keys from the box, trying them.