Jobs2k Reactor

local term = require("term")
local component = require("component")

-------------------------------------------------
-------These can be configured as you need-------

-- The percentage of steam you wish to hold in the tank.
-- Range 1 - 99
steamTarget = 70

-- The amount of time the program rests before begining again.
-- Lower than 0.2 is not advised.
loopSleep = 0.2

-- How many seconds before the turbine is checked for required adjustments.
turbineTimer = 10

-- The amount of steam the turbine should allow at the start.
-- Range: 0 - 2000.
flowStart = 0

-- The amount the reactor rods are inserted at the start. Higher values equal less steam.
-- Range 0 - 100.
rodStart = 100

-- The increase or decrease of steam flowing into the turbine.
-- A higher value increase response to energy draw, but is harder to stabalise.
flowUpDown = 1

-- The percentage of the turbine buffer that will trigger activation/deactivation.
-- Going lower than 30 (or outside the range) is not advised.
-- Range 1 - 99
tBuffer = 50

-----Changing the rest can break the program-----
-------------------------------------------------

reactor = component.br_reactor
turbine = component.br_turbine

reactor.setActive(true)
turbine.setActive(true)
turbine.setFluidFlowRateMax(flowStart)
reactor.setAllControlRodLevels(rodStart)

function turbineCheck ()
    if turbine.getEnergyStored() >= (tBuffer * 10000) then
        turbine.setActive(false)
        if turbine.getRotorSpeed() < 1901 then
            turbine.setFluidFlowRateMax(turbine.getFluidFlowRateMax()-flowUpDown)
        elseif turbine.getRotorSpeed() >= 1901 then
            turbine.setFluidFlowRateMax(turbine.getFluidFlowRateMax()-flowUpDown)
        end
    elseif turbine.getEnergyStored() < (tBuffer * 10000) then
        turbine.setActive(true)
        if turbine.getRotorSpeed() < 1901 then
            if turbine.getFluidFlowRateMax() <= (turbine.getFluidFlowRateMaxMax()-flowUpDown) then
                turbine.setFluidFlowRateMax(turbine.getFluidFlowRateMax()+flowUpDown)
            else
                turbine.setFluidFlowRateMax(2000)
            end
        elseif turbine.getRotorSpeed() > 1901 then
            turbine.setActive(false)
        end
    end
end

function reactorCheck ()
    if reactor.getHotFluidAmount() < 7000 then
        if reactor.getControlRodLevel(0) <= 100 then
            reactor.setAllControlRodLevels(reactor.getControlRodLevel(0)-1)
            reactor.setActive(true)
        end
    elseif reactor.getHotFluidAmount() > 7000 then
        if reactor.getControlRodLevel(0) >= 0 then
            reactor.setAllControlRodLevels(reactor.getControlRodLevel(0)+1)
            reactor.setActive(false)
        end
    end
end

i = 1

while true do

    if math.ceil(i) == 0 then
        turbineCheck()
        reactorCheck()
        i = turbineTimer
    elseif i < turbineTimer then
        reactorCheck()
    end
    term.clear()
    print("Turbine Output: "..math.ceil(turbine.getEnergyProducedLastTick()))
    print("Turbine Buffer: "..turbine.getEnergyStored())
    print("Reactor Rods at "..reactor.getControlRodLevel(0))
    steamTank = math.ceil(reactor.getHotFluidAmount() / (reactor.getHotFluidAmountMax() / 100))
    print("Steam tank "..steamTank.."% full")
    i = i - loopSleep
    if math.ceil(i) <= 0 then
        print("Turbine check in: 0")
    else
        print("Turbine check in: "..math.ceil(i))
    end
    print("Reactor Producing: "..reactor.getHotFluidProducedLastTick())
    print("Turbine Accepting: "..turbine.getFluidFlowRateMax())
    os.sleep(loopSleep)
end