V380 camera V380E2_C2 Boot Logs

U-Boot 2013.10.0-AK_V2.0.04 (Apr 14 2020 - 11:47:31)

DRAM:  64 MiB
set  pin:32 i:5
set  pin:34 i:8
8 MiB
Create flash partition table init OK!
ANYKA SDHC/MMC4.0: 0
Load Env CRC OK!
In:    serial
Out:   serial
Err:   serial
Net:   AKEthernet-0

Hit any key to stop autoboot:  3
 2  1  0

SF: 1307448 bytes @ 0x37000 Read: OK
## Booting kernel from Legacy Image at 81808000 ...
   Image Name:   Linux-3.4.35
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1307384 Bytes = 1.2 MiB
   Load Address: 81808000
   Entry Point:  81808040
   Verifying Checksum ... OK
   XIP Kernel Image ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Anyka Linux Kernel Version: 2.5.02
Booting Linux on physical CPU 0
Linux version 3.4.35 (ma@ma-PC) (gcc version 4.8.5 (anyka (gcc-4.8.5 + binutils-2.24 + ulcibc-0.9.33.2)(20170223)) ) #5 Wed Sep 18 15:36:19 CST 2019
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Cloud39E_AK3918E+H42_V1.0.2
Memory policy: ECC disabled, Data cache writeback
ANYKA CPU AK3918 (ID 0x20150200)
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 10160
Kernel command line: console=ttySAK0,115200n8 root=/dev/mtdblock4 rootfstype=squashfs init=/sbin/init mem=64M memsize=64M
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 40MB = 40MB total
Memory: 36768k/36768k available, 4192k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xc3000000 - 0xff000000   ( 960 MB)
    lowmem  : 0xc0000000 - 0xc2800000   (  40 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .text : 0xc0008000 - 0xc0355000   (3380 kB)
      .init : 0xc0355000 - 0xc036e000   ( 100 kB)
      .data : 0xc036e000 - 0xc0391058   ( 141 kB)
       .bss : 0xc039107c - 0xc03aea18   ( 119 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:95
sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
AK39 console driver initial
console [ttySAK0] enabled
Calibrating delay loop... 199.06 BogoMIPS (lpj=995328)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x81a97438 - 0x81a97490
devtmpfs: initialized
NET: Registered protocol family 16
On-chip L2 memory initialized
AK39 clocks: CPU 400MHz, MEM 200MHz, ASIC 100MHz
Anyka platform share gpio locks initialize.
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-ak39 i2c-ak39: i2c-0: AK39 I2C adapter
Linux video capture interface: v2.00
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
exFAT: Version 1.2.9
jffs2: version 2.2. © 2001-2006 Red Hat, Inc.
msgmni has been set to 71
io scheduler noop registered
io scheduler cfq registered (default)
AK39xx uart driver init, (c) 2013 ANYKA
ak39-uart.0: ttySAK0 at MMIO 0x20130000 (irq = 10) is a AK39
ion: failed to create debug files.
brd: module loaded
loop: module loaded
AK Motor Driver (c) 2013 ANYKA
akgpio driver initialize.
@@@ [akpcm_init]: enter @@@
@@@ [akpcm_probe]: enter @@@
akpcmL0->ak39_codec_probe enter...
akpcm probe: mic on
ak39_set_hp_power 1,soft_de_pipa=1
Headphone driver will power on.
akpcm_probe: OK

akisp_init
Start to init Anyka SPI Flash...
Start to init Anyka partition table...
AK SPI Driver, (c) 2012 ANYKA
akpi regs: SPICON:00000152, SPISTA:00000015, SPIINT:00000000.
ak-spi ak-spi: master is unqueued, this is deprecated
ak_spi setup the master.
pre-scaler=2 (wanted 20Mhz, got 16Mhz)
ak spiflash probe enter.
pre-scaler=2 (wanted 20Mhz, got 16Mhz)
ak_spi_setupxfer,con:00000252.
akspi flash ID: 0x00c22017
ak-spiflash spi0.0: mx25l6405d (8192 Kbytes)
FHA:partition lib version: V1.0.11

FHA:boot block num offset:427
FHA:Sflash_Get_Partition_Startpage g_boot_len:848
mtd_part[0]:
name = KERNEL
size = 0x180000
offset = 0x37000
mask_flags = 0x1

mtd_part[1]:
name = MAC
size = 0x1000
offset = 0x1b7000
mask_flags = 0x1

mtd_part[2]:
name = ENV
size = 0x1000
offset = 0x1b8000
mask_flags = 0x1

mtd_part[3]:
name = A
size = 0x180000
offset = 0x1b9000
mask_flags = 0x1

mtd_part[4]:
name = B
size = 0x199000
offset = 0x339000
mask_flags = 0x1

mtd_part[5]:
name = C
size = 0x133000
offset = 0x4d2000
mask_flags = 0x1

mtd_part[6]:
name = D
size = 0x73000
offset = 0x605000
mask_flags = 0x1

mtd_part[7]:
name = E
size = 0x180000
offset = 0x678000
mask_flags = 0x1

Creating 8 MTD partitions on "spi0.0":
0x000000037000-0x0000001b7000 : "KERNEL"
0x0000001b7000-0x0000001b8000 : "MAC"
0x0000001b8000-0x0000001b9000 : "ENV"
0x0000001b9000-0x000000339000 : "A"
0x000000339000-0x0000004d2000 : "B"
0x0000004d2000-0x000000605000 : "C"
0x000000605000-0x000000678000 : "D"
0x000000678000-0x0000007f8000 : "E"
Init AK SPI Flash finish.
akspi master initialize success, use for DMA mode.
AK39E_MAC Ethernet Driver, V1.0
ak-rtc ak-rtc: rtc core: registered ak-rtc as rtc0
i2c /dev entries driver
AK MCI Driver (c) 2010 ANYKA
akmci ak_sdio: pdev->name:ak_sdio request gpio irq ret = 0, irq=78
akmci ak_sdio: Mci Interface driver.mmc0. using l2dma, hw IRQ. detect mode:GPIO detect.
TCP: cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
ak-rtc ak-rtc: hctosys: invalid date/time
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
devtmpfs: mounted
Freeing init memory: 100K
mount all file system...
starting mdev...
**************************
    Love Linux ! ! !
**************************
SQUASHFS error: Xattrs in filesystem, these will be ignored
SQUASHFS error: unable to read xattr id index table
200+0 records in
200+0 records out
102400 bytes (100.0KB) copied, 0.016345 seconds, 6.0MB/s


V380E login: