Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- ;
- ; VCDS Label File
- ;
- ; Copyright © 2011 Ross-Tech, LLC
- ;
- ; Audi A4 (8D) / Audi A6 (4B) / VW Passat (3B)
- ;
- ; Component: J220 - Engine (#01) - ATQ
- ;
- ; P/N: 3B0-907-551-???
- ;
- ; includes measuring blocks, basic setting, readiness, coding, coding-II, adaptation and long coding
- ;
- ; This file is part of a label file package,
- ; make sure you have all of the following files.
- ;
- ; 3B-01.LBL
- ; 078-907-551-ATQ.LBL (2.8l MPI @ 193 HP - ATQ)
- ;
- ; created on 01/Jun/2011 by Sebastian Stange (Sebastian@Ross-Tech.com)
- ;
- ; last modificationon on 01/Jun/2011
- ;
- ; requires VCDS 10.6.4 or newer
- ;
- ;
- ;---------------------------------------------------
- ;
- ; measuring blocks & basic setting
- ;
- ;---------------------------------------------------
- ;
- ;
- 001,0,General
- 001,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 001,2,Coolant,Temperature (G62),Range: -48.0...+143.0 ∞C\nSpecification (Warm): 80.0...110.0 ∞C
- 001,3,Lambda Control,Bank 1,Range: -25.0...+25.0 %\nSpecification: -10.0...+10.0 %
- 001,4,Lambda Control,Bank 2,Range: -25.0...+25.0 %\nSpecification: -10.0...+10.0 %
- ;
- 002,0,General
- 002,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 002,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 002,3,Injection Timing,,Range: 0.0...20.0 ms\nSpecification (Idle): 1.0...4.0 ms
- 002,4,Mass Air Flow,Sensor (G70),Range: 0.0...200.0 g/s\nSpecification (Idle): 1.0...5.0 g/s\nSpecififcation (Load): min. 160.0 g/s
- ;
- 003,0,General
- 003,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 003,2,Mass Air Flow,Sensor (G70),Range: 0.0...200.0 g/s\nSpecification (Idle): 1.0...5.0 g/s\nSpecififcation (Load): min. 160.0 g/s
- 003,3,Throttle Valve Angle,,Range: 0.0...100.0 %\nSpecification (Idle): 0.2...4.0 %
- 003,4,Ignition,Timing Angle,Range: -20.0...+50.0 ∞BTDC\nSpecification (Idle): 9.0...21.0 ∞BTDC
- ;
- 004,0,General
- 004,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 004,2,Battery Voltage,(Terminal 30),Specification: 11.0...15.0 V
- 004,3,Coolant,Temperature (G62),Range: -40.5...+135.0 ∞C\nSpecification (Warm): 80.0...110.0 ∞C
- 004,4,Intake Air,Temperature (G42),Range: -48.0...+143.0 ∞C\nSpecification (Warm): < +80.0 ∞C (max. +115.0 ∞C)
- ;
- 005,0,General
- 005,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 005,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 005,3,Vehicle Speed,,Range: 0.0...300.0 km/h
- 005,4,Load Status,,Range: Idle/Partial Throttle/Wide Open Throttle (WOT)/Enrichment/Deceleration
- ;
- 006,0,General
- 006,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 006,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 006,3,Intake Air,Temperature (G42),Range: -48.0...+143.0 ∞C\nSpecification (Warm): < +80.0 ∞C (max. +115.0 ∞C)
- 006,4,Altitude,Correction Factor,Range: -50.0...+20.0 %\n\n0.0 % = 0 m\n-50.0 % = 5000 m\n+20.0 % = -2000 m
- ;
- 010,0,Ignition
- 010,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 010,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 010,3,Throttle Valve Angle,,Range: 0.0...100.0 %\nSpecification (Idle): 0.2...4.0 %
- 010,4,Ignition,Timing Angle,Range: -20.0...+50.0 ∞BTDC\nSpecification (Idle): 9.0...21.0 ∞BTDC
- ;
- 011,0,Iginition
- 011,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 011,2,Coolant,Temperature (G62),Range: -48.0...+143.0 ∞C\nSpecification (Warm): 80.0...115.0 ∞C
- 011,3,Intake Air,Temperature (G42),Range: -48.0...+143.0 ∞C\nSpecification (Warm): < +80.0 ∞C (max. +115.0 ∞C)
- 011,4,Ignition,Timing Angle,Range: -20.0...+50.0 ∞BTDC\nSpecification (Idle): 9.0...21.0 ∞BTDC
- ;
- 014,0,Ignition (Misfire Recognition - Total)
- 014,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 014,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 014,3,Misfire Counter,,Specification: 0
- 014,4,Misfire,Recognition,Range: Disabled/Enabled
- ;
- 015,0,Ignition (Misfire Recognition - Cylinder 1-3)
- 015,1,Misfire Counter,Cylinder 1,Specification: 0
- 015,2,Misfire Counter,Cylinder 2,Specification: 0
- 015,3,Misfire Counter,Cylinder 3,Specification: 0
- 015,4,Misfire,Recognition,Range: Active/Disabled
- ;
- 016,0,Ignition (Misfire Recognition - Cylinder 4-6)
- 016,1,Misfire Counter,Cylinder 4,Specification: 0
- 016,2,Misfire Counter,Cylinder 5,Specification: 0
- 016,3,Misfire Counter,Cylinder 6,Specification: 0
- 016,4,Misfire,Recognition,Range: Active/Disabled
- ;
- 018,0,Ignition (Misfire Recognition - RPM/Load Barriers)
- 018,1,Lower,RPM Barrier
- 018,2,Upper,RPM Barrier
- 018,3,Lower,Load Barrier,Range: 0.0...100.0 %
- 018,4,Upper,Load Barrier,Range: 0.0...100.0 %
- ;
- 020,0,Ignition (Timing Retardation Cylinder 1-4)
- 020,1,Timing Retardation,Cylinder 1
- 020,2,Timing Retardation,Cylinder 2
- 020,3,Timing Retardation,Cylinder 3
- 020,4,Timing Retardation,Cylinder 4
- ;
- 021,0,Ignition (Timing Retardation Cylinder 5-8)
- 021,1,Timing Retardation,Cylinder 5
- 021,2,Timing Retardation,Cylinder 6
- 021,3,Timing Retardation,Cylinder 7
- 021,4,Timing Retardation,Cylinder 8
- ;
- 022,0,Ignition (Timing Retardation Cylinder 1 && 2)
- 022,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 022,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 022,3,Timing Retardation,Cylinder 1
- 022,4,Timing Retardation,Cylinder 2
- ;
- 023,0,Ignition (Timing Retardation Cylinder 3 && 4)
- 023,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 023,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 023,3,Timing Retardation,Cylinder 3
- 023,4,Timing Retardation,Cylinder 4
- ;
- 024,0,Ignition (Timing Retardation Cylinder 5 && 6)
- 024,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 024,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 024,3,Timing Retardation,Cylinder 5,Specification: 0.0...12.0 ∞KW
- 024,4,Timing Retardation,Cylinder 6,Specification: 0.0...12.0 ∞KW
- ;
- 026,0,Ignition (Knock Control Cylinder 1-4)
- 026,1,Knock Sensor,Voltage Cylinder 1,Range: 0.0...40.0 V
- 026,2,Knock Sensor,Voltage Cylinder 2,Range: 0.0...40.0 V
- 026,3,Knock Sensor,Voltage Cylinder 3,Range: 0.0...40.0 V
- 026,4,Knock Sensor,Voltage Cylinder 4,Range: 0.0...40.0 V
- ;
- 027,0,Ignition (Knock Control Cylinder 5-8)
- 027,1,Knock Sensor,Voltage Cylinder 5,Range: 0.0...40.0 V
- 027,2,Knock Sensor,Voltage Cylinder 6,Range: 0.0...40.0 V
- 027,3,Knock Sensor,Voltage Cylinder 7,Range: 0.0...40.0 V
- 027,4,Knock Sensor,Voltage Cylinder 8,Range: 0.0...40.0 V
- ;
- 028,0,Ignition (Knock Sensor Test)
- 028,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 028,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 028,3,Coolant,Temperature (G62),Range: -48.0...+143.0 ∞C\nSpecification (Warm): 80.0...115.0 ∞C
- 028,4,Knock Sensor,Test Result,Range: Test ON/Test OFF/Sys. OK/Sys. not OK\nSpecification: Sys. OK
- ;
- B028,0,Ignition (Knock Sensor Test - Short Trip)
- ; Firmly press Brake Pedal and Throttle Pedal at once
- ; Engine Speed increases to 2000 RPM automatically > Field 4 = Test ON
- ; Wait until Field 4 shows "Sys. OK"
- B028,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM\nSpecification (Basic Setting): ~2200 RPM
- B028,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- B028,3,Coolant,Temperature (G62),Range: -48.0...+143.0 ∞C\nSpecification (Warm): 80.0...115.0 ∞C
- B028,4,Knock Sensor,Test Result,Range: Test ON/Test OFF/Sys. OK/Sys. not OK\nSpecification: Sys. OK
- ;
- 030,0,Lambda Control (Sensor Status)
- 030,1,Bank 1,Sensor 1,1xx = Lambda Sensor Heating on\nx1x = Lambda Sensor ready\nxx1 = Lambda Control active
- 030,2,Bank 1,Sensor 2,1xx = Lambda Sensor Heating on\nx1x = Lambda Sensor ready\nxx1 = Lambda Control active
- 030,3,Bank 2,Sensor 1,1xx = Lambda Sensor Heating on\nx1x = Lambda Sensor ready\nxx1 = Lambda Control active
- 030,4,Bank 2,Sensor 2,1xx = Lambda Sensor Heating on\nx1x = Lambda Sensor ready\nxx1 = Lambda Control active
- ;
- 031,0,Lambda Control (Lambda Sensor Voltages)
- 031,1,Lambda Control,Bank 1 (actual)
- 031,2,Lambda Control,Bank 1 (specified)
- 031,3,Lambda Control,Bank 2 (actual)
- 031,4,Lambda Control,Bank 2 (specified)
- ;
- 032,0,Lambda Control (Mixture Adaptation)
- 032,1,Adaptation (Idle),Bank 1 Sensor 1,Range: -25.0...+25.0 %\nSpecification: -10.0...+10.0 %
- 032,2,Adaptation (Partial),Bank 1 Sensor 1,Range: -25.0...+25.0 %\nSpecification: -10.0...+10.0 %
- 032,3,Adaptation (Idle),Bank 2 Sensor 1,Range: -25.0...+25.0 %\nSpecification: -10.0...+10.0 %
- 032,4,Adaptation (Partial),Bank 2 Sensor 1,Range: -25.0...+25.0 %\nSpecification: -10.0...+10.0 %
- ;
- 033,0,Lambda Control
- 033,1,Lambda Control,Bank 1 Sensor 1,Range: -25.0...+25.0 %\nSpecification: -10.0...+10.0 %
- 033,2,Sensor Voltage,Bank 1 Sensor 1,Range: 0.0...5.0 V
- 033,3,Lambda Control,Bank 2 Sensor 1,Range: -25.0...+25.0 %\nSpecification: -10.0...+10.0 %
- 033,4,Sensor Voltage,Bank 2 Sensor 1,Range: 0.0...5.0 V
- ;
- 034,0,Lambda Control (Aging Check: Bank 1 Sensor 1)
- 034,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 034,2,Catalytic Converter,Bank 1 Temp.,Specification: min. 300.0 ∞C
- 034,3,Periodic Time,Bank 1 Sensor 1,Specification: 0.1...1.8 s
- 034,4,Result,Lambda Aging,Range: Test ON/Test OFF/B1-S1 not OK/B1-S1 OK\nSpecification: Test OFF
- ;
- B034,0,Lambda Control (Aging Check: Bank 1 Sensor 1)
- ; "Activate" Basic Setting
- ; Firmly press Brake Pedal and Throttle Pedal at once
- ; Engine Speed increases automatically > Field 4 = Test ON
- ; Wait until Field 4 shows "B1-S1 OK"
- B034,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM\nSpecification (Basic Setting): ~2200 RPM
- B034,2,Catalytic Converter,Bank 1 Temp.,Specification: min. 300.0 ∞C
- B034,3,Periodic Time,Bank 1 Sensor 1,Specification: 0.1...1.8 s
- B034,4,Result,Lambda Aging,Range: Test ON/Test OFF/B1-S1 not OK/B1-S1 OK\nSpecification: B1-S1 OK
- ;
- 035,0,Lambda Control (Aging Check: Bank 2 Sensor 1)
- 035,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 035,2,Catalytic Converter,Bank 2 Temp.,Specification: min. 300.0 ∞C
- 035,3,Periodic Time,Bank 2 Sensor 1,Specification: 0.1...1.8 s
- 035,4,Result,Lambda Aging,Range: Test ON/Test OFF/B2-S1 not OK/B2-S1 OK\nSpecification: Test OFF
- ;
- B035,0,Lambda Control (Aging Check: Bank 2 Sensor 1)
- ; "Activate" Basic Setting
- ; Firmly press Brake Pedal and Throttle Pedal at once
- ; Engine Speed increases automatically > Field 4 = Test ON
- ; Wait until Field 4 shows "B2-S1 OK"
- B035,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM\nSpecification (Basic Setting): ~2200 RPM
- B035,2,Catalytic Converter,Bank 2 Temp.,Specification: min. 300.0 ∞C
- B035,3,Periodic Time,Bank 2 Sensor 1,Specification: 0.1...1.8 s
- B035,4,Result,Lambda Aging,Range: Test ON/Test OFF/B2-S1 not OK/B2-S1 OK\nSpecification: B2-S1 OK
- ;
- 036,0,Lambda Control (Sensor Readiness - After Catalyst)
- 036,1,Sensor Voltage,Bank 1 Sensor 2,Range: 0.0...1.0 V\nSpecification: 0.X00...0.X00 V
- 036,2,Result,Lambda Availability,Range: Test ON/Test OFF/B1-S2 not OK/B1-S2 OK\nSpecification: Test OFF
- 036,3,Sensor Voltage,Bank 2 Sensor 2,Range: 0.0...1.0 V\nSpecification: 0.X00...0.X00 V
- 036,4,Result,Lambda Availability,Range: Test ON/Test OFF/B2-S2 not OK/B2-S2 OK\nSpecification: Test OFF
- ;
- B036,0,Lambda Control (Sensor Readiness - After Catalyst)
- ; "Activate" Basic Setting
- ; Firmly press Brake Pedal and Throttle Pedal at once
- ; Engine Speed increases automatically > Field 4 = Test ON
- ; Wait until Field 4 shows "B1-S2 OK"
- B036,1,Sensor Voltage,Bank 1 Sensor 2,Range: 0.0...1.0 V\nSpecification: 0.X00...0.X00 V
- B036,2,Result,Lambda Availability,Range: Test ON/Test OFF/B1-S2 not OK/B1-S2 OK\nSpecification: B1-S2 OK
- B036,3,Sensor Voltage,Bank 2 Sensor 2,Range: 0.0...1.0 V\nSpecification: 0.X00...0.X00 V
- B036,4,Result,Lambda Availability,Range: Test ON/Test OFF/B2-S2 not OK/B2-S2 OK\nSpecification: B2-S2 OK
- ;
- 037,0,Lambda Control (Delta Lambda Bank 1)
- 037,1,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 037,2,Sensor Voltage,Bank 1 Sensor 2,Range: 0.0...1.0 V\nSpecification: 0.X00...0.X00 V
- 037,3,Adjustment,Bank 1 Sensor 2
- 037,4,Result,Delta Lambda B1,Range: Test ON/Test OFF/B1-S1 OK/B1-S1 n.OK\nSpecification: Test OFF
- ;
- B037,0,Lambda Control (Delta Lambda Bank 1)
- ; "Activate" Basic Setting
- ; Firmly press Brake Pedal and Throttle Pedal at once
- ; Engine Speed increases automatically > Field 4 = Test ON
- ; Wait until Field 4 shows "B1-S1 OK"
- B037,1,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- B037,2,Sensor Voltage,Bank 1 Sensor 2,Range: 0.0...1.0 V\nSpecification: 0.X00...0.X00 V
- B037,3,Adjustment,Bank 1 Sensor 2
- B037,4,Result,Delta Lambda B1,Range: Test ON/Test OFF/B1-S1 OK/B1-S1 n.OK\nSpecification: B1-S1 OK
- ;
- 038,0,Lambda Control (Delta Lambda Bank 2)
- 038,1,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 038,2,Sensor Voltage,Bank 2 Sensor 2,Range: 0.0...1.0 V\nSpecification: 0.X00...0.X00 V
- 038,3,Adjustment,Bank 2 Sensor 2
- 038,4,Result,Delta Lambda B2,Range: Test ON/Test OFF/B2-S1 OK/B2-S1 n.OK\nSpecification: Test OFF
- ;
- B038,0,Lambda Control (Delta Lambda Bank 2)
- ; "Activate" Basic Setting
- ; Firmly press Brake Pedal and Throttle Pedal at once
- ; Engine Speed increases automatically > Field 4 = Test ON
- ; Wait until Field 4 shows "B2-S1 OK"
- B038,1,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- B038,2,Sensor Voltage,Bank 2 Sensor 2,Range: 0.0...1.0 V\nSpecification: 0.X00...0.X00 V
- B038,3,Adjustment,Bank 2 Sensor 2
- B038,4,Result,Delta Lambda B2,Range: Test ON/Test OFF/B2-S1 OK/B2-S1 n.OK\nSpecification: B2-S1 OK
- ;
- 041,0,Lambda Control (Lambda Sensor Heating Bank 1)
- 041,1,Resistance,Bank 1 Sensor 1,Range: 0.0...0.9 kOhms
- 041,2,Heater Condition,Bank 1 Sensor 1,Range: Htg. S1 OFF/Htg. S1 ON
- 041,3,Resistance,Bank 1 Sensor 2,Range: 0.0...0.9 kOhms
- 041,4,Heater Condition,Bank 1 Sensor 2,Range: Htg. S2 OFF/Htg. S2 ON
- ;
- 042,0,Lambda Control (Lambda Sensor Heating Bank 2)
- 042,1,Resistance,Bank 2 Sensor 1,Range: 0.0...0.9 kOhms
- 042,2,Heater Condition,,Bank 1 Sensor 1,Range: Htg. S1 OFF/Htg. S1 ON
- 042,3,Resistance,Bank 2 Sensor 2,Range: 0.0...0.9 kOhms
- 042,4,Heater Condition,Bank 1 Sensor 2,Range: Htg. S2 OFF/Htg. S2 ON
- ;
- 043,0,Lambda Control (Aging Check: Bank 1 Sensor 2)
- 043,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 043,2,Catalytic Converter,Bank 1 Temp.,Specification: min. 300.0 ∞C
- 043,3,Lambda Voltage,Bank 1 Sensor 1,Range: 0.0...1.0 V\nSpecification: 0.000...1.000 V
- 043,4,Lambda Sensor,Aging Test B1S2,Range: Test ON/Test OFF/B1-S2 OK/B1-S2 n.OK\nSpecification: Test OFF
- ;
- B043,0,Lambda Control (Aging Check: Bank 1 Sensor 2)
- ; "Activate" Basic Setting
- ; Firmly press Brake Pedal and Throttle Pedal at once
- ; Engine Speed increases automatically > Field 4 = Test ON
- ; Wait until Field 4 shows "B1-S2 OK"
- B043,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM\nSpecification (Basic Setting): ~2200 RPM
- B043,2,Catalytic Converter,Bank 1 Temp.,Specification: min. 300.0 ∞C
- B043,3,Lambda Voltage,Bank 1 Sensor 2,Range: 0.0...1.0 V\nSpecification: 0.000...1.000 V
- B043,4,Lambda Sensor,Aging Test B1S2,Range: Test ON/Test OFF/B1-S2 OK/B1-S2 n.OK\nSpecification: B1-S2 OK
- ;
- 044,0,Lambda Control (Aging Check: Bank 2 Sensor 2)
- 044,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 044,2,Catalytic Converter,Bank 2 Temp.,Specification: min. 300.0 ∞C
- 044,3,Lambda Voltage,Bank 2 Sensor 1,Range: 0.0...1.0 V\nSpecification: 0.000...1.000 V
- 044,4,Lambda Sensor,Aging Test B2S2,Range: Test ON/Test OFF/B2-S2 OK/B2-S2 n.OK\nSpecification: B2-S2 OK
- ;
- B044,0,Lambda Control (Aging Check: Bank 2 Sensor 2)
- ; "Activate" Basic Setting
- ; Firmly press Brake Pedal and Throttle Pedal at once
- ; Engine Speed increases automatically > Field 4 = Test ON
- ; Wait until Field 4 shows "B2-S2 OK"
- B044,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM\nSpecification (Basic Setting): ~2200 RPM
- B044,2,Catalytic Converter,Bank 2 Temp.,Specification: min. 300.0 ∞C
- B044,3,Lambda Voltage,Bank 2 Sensor 2,Range: 0.0...1.0 V\nSpecification: 0.000...1.000 V
- B044,4,Lambda Sensor,Aging Test B2S2,Range: Test ON/Test OFF/B2-S2 OK/B2-S2 n.OK\nSpecification: B2-S2 OK
- ;
- 046,0,Lambda Control (Catalytic Conversion Test Bank 1)
- 046,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 046,2,Catalytic Converter,Bank 1 Temp.,Specification: min. 300.0 ∞C
- 046,3,Catalytic,Conversion Bank 1
- 046,4,Cat. Conversion,Test Bank 1,Range: Test ON/Test OFF/CatB1 OK/CatB1 n.OK\nSpecification: CatB1 OK
- ;
- B046,0,Lambda Control (Catalytic Conversion Test Bank 1)
- ; Short Trips 034/035/036/037/038/039/043/044 must be OK
- ; "Activate" Basic Setting
- ; Firmly press Brake Pedal and Throttle Pedal at once
- ; Engine Speed increases automatically > Field 4 = Test ON
- ; Wait until Field 4 shows "CatB1 OK"
- B046,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM\nSpecification (Basic Setting): ~2200 RPM
- B046,2,Catalytic Converter,Bank 1 Temp.,Specification: min. 300.0 ∞C
- B046,3,Catalytic,Conversion Bank 1
- B046,4,Cat. Conversion,Test Bank 1,Range: Test ON/Test OFF/CatB1 OK/CatB1 n.OK\nSpecification: CatB1 OK
- ;
- 047,0,Lambda Control (Catalytic Conversion Test Bank 2)
- 047,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 047,2,Catalytic Converter,Bank 2 Temp.,Specification: min. 300.0 ∞C
- 047,3,Catalytic,Conversion Bank 2
- 047,4,Cat. Conversion,Test Bank 2,Range: Test ON/Test OFF/CatB2 OK/CatB2 n.OK\nSpecification: CatB2 OK
- ;
- B047,0,Lambda Control (Catalytic Conversion Test Bank 2)
- ; Short Trips 034/035/036/037/038/039/043/044 must be OK
- ; "Activate" Basic Setting
- ; Firmly press Brake Pedal and Throttle Pedal at once
- ; Engine Speed increases automatically > Field 4 = Test ON
- ; Wait until Field 4 shows "CatB2 OK"
- B047,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM\nSpecification (Basic Setting): ~2200 RPM
- B047,2,Catalytic Converter,Bank 2 Temp.,Specification: min. 300.0 ∞C
- B047,3,Catalytic,Conversion Bank 2
- B047,4,Cat. Conversion,Test Bank 2,Range: Test ON/Test OFF/CatB2 OK/CatB2 n.OK\nSpecification: CatB2 OK
- ;
- 050,0,Idle Speed Stabilization
- 050,1,Engine Speed,(actual),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 050,2,Engine Speed,(specified),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 050,3,A/C Readiness,,Range: A/C-Low / A/C-High
- 050,4,A/C Compressor,,Range: Compr.OFF/Compr.ON
- ;
- 051,0,Idle Speed Stabilization (Gear shifts)
- 051,1,Engine Speed,(actual),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 051,2,Engine Speed,(specified),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 051,3,Selected Gear,,P or N = 0\nGear = 1 - 6\nR = 7
- 051,4,Battery Voltage,(Terminal 30),Specification: 11.0...15.0 V
- ;
- 053,0,Idle Speed Stabilization (Generator Load)
- 053,1,Engine Speed,(actual),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 053,2,Engine Speed,(specified),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 053,3,Battery Voltage,(Terminal 30),Specification: 11.0...15.0 V
- 053,4,Generator Load,,Range: 0.0...100.0 %
- ;
- 054,0,Idle Speed Stabilization
- 054,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 054,2,Load Status,,Range: Idle/Partial Throttle/Wide Open Throttle (WOT)/Enrichment/Deceleration
- 054,3,Accel. Pedal Pos.,Sensor 1 (G79),Range: 0.0...100.0 %
- 054,4,Throttle Valve Angle,,Range: 0.0...100.0 %\nSpecification (Idle): 0.2...4.0 %
- ;
- 055,0,Idle Speed Stabilization
- 055,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 055,2,Idle Regulator,,Specification: -5.0...+5.0 %
- 055,3,Idle Stabilization,Self-Adaptation,Specification: -5.0...+5.0 %
- 055,4,Operating,Condition,x0xxx? = A/C Compressor\nx0xx?x = Gear engaged\nx0x?xx = A/C Readiness\nx0?xxx = Rear Window Heater\n?0xxxx = Front Window Heater
- ;
- 056,0,Idle Speed Stabilization
- 056,1,Engine Speed,(actual),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 056,2,Engine Speed,(specified),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 056,3,Idle Regulator,,Specification: -5.0...+5.0 %
- 056,4,Operating,Condition,x0xxx? = A/C Compressor\nx0xx?x = Gear engaged\nx0x?xx = A/C Readiness\nx0?xxx = Rear Window Heater\n?0xxxx = Front Window Heater
- ;
- 057,0,Idle Speed Stabilization (Air Condition)
- 057,1,Engine Speed,(actual),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 057,2,Engine Speed,(specified),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 057,3,A/C Compressor,,Range: Compr.OFF/Compr.ON
- ;
- 060,0,Electronic Throttle (Throttle Body Alignment)
- 060,1,Throttle Valve,Sensor 1 (G187),Range: 0.0...100.0 %\nSpecification: 3.0...93.0 %\nSpecification (Idle): 3.0...93.0 %
- 060,2,Throttle Valve,Sensor 2 (G188),Range: 0.0...100.0 %\nSpecification: 97.0...3.0 %\nSpecification (Idle): 97.0...3.0 %
- 060,3,Throttle Valve,Steps Counter,Range: 0...8\nSpecification: 8
- 060,4,Throttle Body,Alignment Status,Range: ADP RUN/ADP. O.K./ADP ERROR\nSpecification: ADP. O.K.
- ;
- B060,0,Throttle Body Alignment
- ; "Activate" Basic Setting
- ; Wait until Field 4 shows "ADP OK"
- B060,1,Throttle Valve,Sensor 1 (G187),Range: 0.0...100.0 %\nSpecification: 3.0...93.0 %\nSpecification (Idle): 3.0...93.0 %
- B060,2,Throttle Valve,Sensor 2 (G188),Range: 0.0...100.0 %\nSpecification: 97.0...3.0 %\nSpecification (Idle): 97.0...3.0 %
- B060,3,Throttle Adaptation,Steps Counter,Range: 0...8\nSpecification: 8
- B060,4,Throttle Body,Alignment Status,Range: ADP RUN/ADP OK/ADP ERROR\nSpecification: ADP OK
- ;
- 061,0,Electronic Throttle
- 061,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 061,2,Battery Voltage,(Terminal 30),Specification: 12.0...15.0 V
- 061,3,Throttle Valve Angle,,Range: 0.0...100.0 %\nSpecification (Idle): 0.2...4.0 %
- 061,4,Operating,Condition,x0xxx? = A/C Compressor\nx0xx?x = Gear engaged\nx0x?xx = A/C Readiness\nx0?xxx = Rear Window Heater\n?0xxxx = Front Window Heater
- ;
- 062,0,Electronic Throttle (Sensor Values)
- 062,1,Throttle Valve,Sensor 1 (G187),Range: 0.0...100.0 %\nSpecification: 3.0...93.0 %
- 062,2,Throttle Valve,Sensor 2 (G188),Range: 0.0...100.0 %\nSpecification: 97.0...3.0 %
- 062,3,Accel. Pedal Pos.,Sensor 1 (G79),Range: 0.0...100.0 %\nSpecification: 12.0...97.0 %
- 062,4,Accel. Pedal Pos.,Sensor 2 (G185),Range: 0.0...100.0 %\nSpecification: 4.0...49.0 %
- ;
- 063,0,Electronic Throttle (Kick-Down Alignment)
- 063,1,Accel. Pedal Pos.,Sensor 1 (G79),Range: 0.0...100.0 %\nSpecification: 12.0...97.0 %\nSpecification (Kick-Down): 79.0...94.0 %
- 063,2,Kick-Down,Alignment Value,Range: 0.0...100.0 %\nSpecification: 79.0...94.0 %
- 063,3,Kick-Down,Switch,Range: Kick Down
- 063,4,Kick-Down,Alignment Status,Range: ADP RUN/ADP OK/ADP ERROR\nSpecification: ADP OK
- ;
- B063,0,Kick-Down Alignment (Automatic Transmission only)
- ; "Activate" Basic Setting
- ; Press the Accelerator Pedal down to the floor
- ; Wait until Field 4 shows "ADP OK"
- B063,1,Throttle Position,Sensor (G79),Range: 0.0...100.0 %\nSpecification: 12.0...97.0 %\nSpecification (Kick-Down): 79.0...94.0 %
- B063,2,Kick-Down,Alignment Value,Range: 0.0...100.0 %\nSpecification: 79.0...94.0 %
- B063,3,Kick-Down,Switch,Range: Kick Down
- B063,4,Kick-Down,Alignment Status,Range: ADP RUN/ADP OK/ADP ERROR\nSpecification: ADP OK
- ;
- 064,0,Electronic Throttle (Sensor Adaption Values)
- 064,1,Lower Adaptation,Sensor 1 (G187),Specification: 0.4...0.6 V
- 064,2,Lower Adaptation,Sensor 2 (G188),Specification: 4.0...5.0 V
- 064,3,Emergency Air Gap,Sensor 1 (G187),Specification: 0.5...1.0 V
- 064,4,Emergency Air Gap,Sensor 2 (G188),Specification: 4.0...5.0 V
- ;
- 066,0,Electronic Throttle (Cruise Control System)
- 066,1,Vehicle Speed,(current)
- 066,2,Switch Positions I,,xxx? = Brake Light Switch\nxx?x = Brake Pedal Switch\nx?xx = Clutch Pedal Switch\n?xxx = CCS (Cruise Control System) enabled
- 066,3,Vehicle Speed,(specified)
- 066,4,Switch Positions II,,xxx? = CCS ON (CAN)\nxx?x = SET (CCS ON)\nx?xx = Deceleration (-)\n?xxx = Acceleration (+)
- ;
- 067,0,Electronic Throttle (Cruise Control System)
- 067,1,Cruise Control,Shut-Off Crit. (rev.)
- 067,2,Switch Positions I,,xxxxxxx? = Brake Light Switch\nxxxxxx?x = Brake Pedal Switch\nxxxxx?xx = Clutch Pedal Switch\nxxxx?xxx = CCS (Cruise Control System) enabled\nxxx?xxxx = ACC (Adaptive Cruise Control) available\nxx?xxxxx = Main Switch engaged\n??xxxxxx = CCS Status
- 067,3,Cruise Control,Shut-Off Crit. (irrev.)
- ;
- 068,0,Transmission Status
- 068,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 068,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 068,3,Selected Gear,,P or N = 0\nGear = 1 - 6\nR = 7
- 068,4,Torque,Converter/Clutch,Range: TC Open/TC Closed/TC Control
- ;
- 070,0,Emission Reduction (EVAP Valve Test)
- 070,1,Evap. Emissions,Sol. Valve (Open),Range: 0.0...100.0 %
- 070,2,Lambda Control,,Range: -25.0...+25.0 %
- 070,3,Evap. Emissions,Sol. Valve (Flow)
- 070,4,EVAP Valve,Test,Range: Test ON/Test OFF/TEV OK/TEV not OK\nSpecification: Test OFF
- ;
- B070,0,Emission Reduction (EVAP Valve Test)
- ; "Activate" Basic Setting
- ; Wait until Field 4 shows "TEV OK"
- B070,1,Evap. Emissions,Sol. Valve (Open),Range: 0.0...100.0 %
- B070,2,Lambda Control,,Range: -25.0...+25.0 %
- B070,3,Evap. Emissions,Sol. Valve (Flow)
- B070,4,EVAP Valve,Test,Range: Test ON/Test OFF/TEV OK/TEV not OK\nSpecification: TEV OK
- ;
- 071,0,Emission Reduction (Leak Diagnostic System)
- 071,1,Reed Contact,Condition,Range: Reed Open/Reed Closed
- 071,2,Malfunction,Message,Range: Small Leak/Large Leak/Abort
- 071,3,Test Status,,Range: System Test/Meas. End
- 071,4,Leak Diagnostic,Test Status,Range: Test ON/Test OFF/Syst. OK/Syst. not OK\nSpecification: Test OFF
- ;
- B071,0,Emission Reduction (Leak Diagnostic Pump)
- ; "Activate" Basic Setting
- ; Wait until Field 4 shows "Syst. OK"
- B071,1,Reed Contact,Condition,Range: Reed Open/Reed Closed
- B071,2,Malfunction,Message,Range: Small Leak/Large Leak/Abort
- B071,3,Test Status,,Range: System Test/Meas. End
- B071,4,Leak Diagnostic,Test Status,Range: Test ON/Test OFF/Syst. OK/Syst. not OK\nSpecification: Syst. OK
- ;
- 077,0,Emission Reduction (Secondary Air Injection: Bank 1)
- 077,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 077,2,Mass Air Flow,Sensor (G70),Range: 0.0...200.0 g/s\nSpecification (Idle): 1.0...5.0 g/s\nSpecififcation (Load): min. 160.0 g/s
- 077,3,Air Mass from,Sec. Air Inj. Bank 1,Range: -100.0...+50.0 %
- 077,4,Secondary Air,Injection Test B1,Range: Test ON/Test OFF/Syst. OK/Syst. n.OK\nSpecification: Test OFF
- ;
- B077,0,Emission Reduction (Secondary Air Injection: Bank 1)
- ; "Activate" Basic Setting
- ; Firmly press Brake Pedal and Throttle Pedal at once
- ; Engine Speed increases automatically > Field 4 = Test ON
- ; Wait until Field 4 shows "Syst. OK"
- ; NOTE: Can only be performed once per engine start!
- B077,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM\nSpecification (Basic Setting): ~2200 RPM
- B077,2,Mass Air Flow,Sensor (G70),Range: 0.0...200.0 g/s\nSpecification (Idle): 1.0...5.0 g/s\nSpecififcation (Load): min. 160.0 g/s
- B077,3,Air Mass from,Sec. Air Inj. Bank 1,Range: -100.0...+50.0 %\nSpecification (Basic Setting): min. -XX.0 %
- B077,4,Secondary Air,Injection Test B1,Range: Test ON/Test OFF/Syst. OK/Syst. n.OK\nSpecification: Syst. OK
- ;
- 078,0,Emission Reduction (Secondary Air Injection: Bank 2)
- 078,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 078,2,Mass Air Flow,Sensor (G70),Range: 0.0...200.0 g/s\nSpecification (Idle): 1.0...5.0 g/s\nSpecififcation (Load): min. 160.0 g/s
- 078,3,Air Mass from,Sec. Air Inj. Bank 2,Range: -100.0...+50.0 %
- 078,4,Secondary Air,Injection Test B2,Range: Test ON/Test OFF/Syst. OK/Syst. n.OK\nSpecification: Test OFF
- ;
- B078,0,Emission Reduction (Secondary Air Injection: Bank 2)
- ; "Activate" Basic Setting
- ; Firmly press Brake Pedal and Throttle Pedal at once
- ; Engine Speed increases automatically > Field 4 = Test ON
- ; Wait until Field 4 shows "Syst. OK"
- ; NOTE: Can only be performed once per engine start!
- B078,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM\nSpecification (Basic Setting): ~2200 RPM
- B078,2,Mass Air Flow,Sensor (G70),Range: 0.0...200.0 g/s\nSpecification (Idle): 1.0...5.0 g/s\nSpecififcation (Load): min. 160.0 g/s
- B078,3,Air Mass from,Sec. Air Inj. Bank 2,Range: -100.0...+50.0 %\nSpecification (Basic Setting): min. -XX.0 %
- B078,4,Secondary Air,Injection Test B2,Range: Test ON/Test OFF/Syst. OK/Syst. n.OK\nSpecification: Syst. OK
- ;
- 086,0,Readiness Code I
- 086,1,Readiness Bits,,xxxxxxx? = Catalyst(s)\nxxxxxx?x = Catalyst Heating\nxxxxx?xx = EVAP System\nxxxx?xxx = Secondary Air Injection System\nxxx?xxxx = Climate Control\nxx?xxxxx = Oxygen Sensor(s)\nx?xxxxxx = Oxygen Sensor Heating\n?xxxxxxx = Exhaust Gas Recirculation (EGR)\n\n0 = completed\n1 = not completed
- 086,2,Cycle Flags I,,xxxxxxx? = Catalyst Bank 1\nxxxxxx?x = Catalyst Bank 2\nxxxxx?xx = Leak Diagnostic Pump\nxxxx?xxx = EVAP Valve\nxxx?xxxx = Oxygen Sensor Heater Bank 1 Sensor 1\nxx?xxxxx = Oxygen Sensor Heater Bank 1 Sensor 2\nx?xxxxxx = Oxygen Sensor Heater Bank 2 Sensor 1\n?xxxxxxx = Oxygen Sensor Heater Bank 2 Sensor 2\n\n0 = completed\n1 = not completed
- 086,3,Cycle Flags II,(Part 1),0xxxxxx? = Bank 1 Sensor 1 elec.\n0xxxxx?x = Bank 1 Sensor 2 elec.\n0xxxx?xx = Bank 1 Sensor 1 (Delta-Lambda Shift)\n0xxx?xxx = Bank 1 Sensor 2 (Sensor Aging)\n0xx?xxxx = Bank 1 Sensor 1 (Period Duration)\n0x?xxxxx = Secondary Air Injection Bank 1\n0?0xxxxx = Secondary Air Injection Bank 2\n\n0 = completed\n1 = not completed
- 086,4,Cycle Flags II,(Part 2),0xxxxxx? = Bank 2 Sensor 1 elec.\n0xxxxx?x = Bank 2 Sensor 2 elec.\n0xxxx?xx = Bank 2 Sensor 1 (Delta-Lambda Shift)\n0xxx?xxx = Bank 2 Sensor 2 (Sensor Aging)\n0xx?xxxx = Bank 2 Sensor 1 (Period Duration)\n0x?xxxxx = Secondary Air Injection Bank 1\n0?xxxxxx = Secondary Air Injection Bank 2\n\n0 = completed\n1 = not completed
- ;
- 087,0,Readiness and Error Bits
- 087,1,Readiness Bits,,xxxxxxx? = Catalyst(s)\nxxxxxx?x = Catalyst Heating\nxxxxx?xx = EVAP System\nxxxx?xxx = Secondary Air Injection System\nxxx?xxxx = Climate Control\nxx?xxxxx = Oxygen Sensor(s)\nx?xxxxxx = Oxygen Sensor Heating\n?xxxxxxx = Exhaust Gas Recirculation (EGR)\n\n0 = completed\n1 = not completed
- 087,2,Error Flags I,,xxxxxxx? = Catalyst Bank 1\nxxxxxx?x = Catalyst Bank 2\nxxxxx?xx = Leak Diagnostic Pump\nxxxx?xxx = EVAP Valve\nxxx?xxxx = Oxygen Sensor Heater Bank 1 Sensor 1\nxx?xxxxx = Oxygen Sensor Heater Bank 1 Sensor 2\nx?xxxxxx = Oxygen Sensor Heater Bank 2 Sensor 1\n?xxxxxxx = Oxygen Sensor Heater Bank 2 Sensor 2\n\n0 = completed\n1 = not completed
- 087,3,Error Flags II,(Part 1),0xxxxxx? = Bank 1 Sensor 1 elec.\n0xxxxx?x = Bank 1 Sensor 2 elec.\n0xxxx?xx = Bank 1 Sensor 1 (Delta-Lambda Shift)\n0xxx?xxx = Bank 1 Sensor 2 (Sensor Aging)\n0xx?xxxx = Bank 1 Sensor 1 (Period Duration)\n0x?xxxxx = Secondary Air Injection Bank 1\n0?0xxxxx = Secondary Air Injection Bank 2\n\n0 = completed\n1 = not completed
- 087,4,Error Flags II,(Part 2),0xxxxxx? = Bank 2 Sensor 1 elec.\n0xxxxx?x = Bank 2 Sensor 2 elec.\n0xxxx?xx = Bank 2 Sensor 1 (Delta-Lambda Shift)\n0xxx?xxx = Bank 2 Sensor 2 (Sensor Aging)\n0xx?xxxx = Bank 2 Sensor 1 (Period Duration)\n0x?xxxxx = Secondary Air Injection Bank 1\n0?xxxxxx = Secondary Air Injection Bank 2\n\n0 = completed\n1 = not completed
- ;
- 088,0,Cycle Flags
- 088,1,Cycle Flags I,,xxxxxxx? = Exhaust Camshaft Bank 2\nxxxxxx?x = Exhaust Camshaft Bank 1\nxxxxx?xx = Intake Camshaft Bank 2\nxxxx?xxx = Intake Camshaft Bank 1\nxxx?xxxx = Knock Sensor 4\nxx?xxxxx = Knock Sensor 3\nx?xxxxxx = Knock Sensor 2\n?xxxxxxx = Knock Sensor 1\n\n0 = completed\n1 = not completed
- 088,2,Cycle Flags II,,xxxxxxx? = Brake Light Switch\nxxxxxx?x = Clutch Pedal Switch\nxxxxx?xx = Idle Speed Control\nxxxx?xxx = Speed Signal\nxxx?xxxx = Idle Switch\nxx?xxxxx = Coolant Temperature Sensor\nx?xxxxxx = Throttle Valve Potentiometer\n?xxxxxxx = Mass Air Flow Sensor\n\n0 = completed\n1 = not completed
- 088,3,Cycle Flags III,,xxx0x?00 = Intake Air Temperature Sensor\nxxx0?x00 = Thermostat (only USA)\nxx?0xx00 = Cruise Control Lever\nx?x0xx00 = Oxygen Sensor Control - Adaptation Bank 2\n?xx0xx00 = Oxygen Sensor Control - Adaptation Bank 1\n\n0 = completed\n1 = not completed
- ;
- 089,0,On-Board-Diagnostics (OBD)
- 089,1,Distance Driven,with MIL on
- 089,2,Tank Condition,,Range: OK/too low
- ;
- 090,0,Camshaft Adjustment (Intake)
- 090,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 090,2,Cam. Adjustment,Intake Status,Range: Cam Ctrl. ON/Cam Ctrl. OFF
- 090,3,Cam. Adjustment,Intake B1 (act.)
- 090,4,Cam. Adjustment,Intake B2 (act.)
- ;
- 091,0,Camshaft Adjustment (Bank 1 Intake)
- 091,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 091,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 091,3,Cam. Adjustment,Intake Status,Range: Cam Ctrl. ON/Cam Ctrl. OFF
- 091,4,Cam. Adjustment,Intake B1 (act.),Range: -3.0...+25.0 ∞KW
- ;
- 092,0,Camshaft Adjustment (Bank 2 Intake)
- 092,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 092,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 092,3,Cam. Adjustment,Intake Status,Range: Cam Ctrl. ON/Cam Ctrl. OFF
- 092,4,Cam. Adjustment,Intake B2 (act.),Range: -3.0...+25.0 ∞KW
- ;
- 093,0,Camshaft Adjustment Adaptation
- 093,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 093,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 093,3,Phase Position,Bank 1 Intake
- 093,4,Phase Position,Bank 2 Intake
- ;
- 094,0,Camshaft Adjustment (Intake)
- 094,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 094,2,Cam. Adjustment,Intake Status,Range: Cam Ctrl. ON/Cam Ctrl. OFF
- 094,3,Cam. Adj. Test,Bank 1 Intake,Range: Test ON/Test OFF/Syst. OK/Syst. not OK\nSpecification: Syst. not OK
- 094,4,Cam. Adj. Test,Bank 2 Intake,Range: Test ON/Test OFF/Syst. OK/Syst. not OK\nSpecification: Syst. not OK
- ;
- B094,0,Camshaft Adjustment (Intake)
- B094,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM\nSpecification (Basic Setting): ~2200 RPM
- B094,2,Cam. Adjustment,Intake Status,Range: Cam Ctrl. ON/Cam Ctrl. OFF
- B094,3,Cam. Adj. Test,Bank 1 Intake,Range: Test ON/Test OFF/Syst. OK/Syst. not OK\nSpecification: Syst. not OK
- B094,4,Cam. Adj. Test,Bank 2 Intake,Range: Test ON/Test OFF/Syst. OK/Syst. not OK\nSpecification: Syst. not OK
- ;
- 095,0,Intake Manifold Change-Over
- 095,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 095,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 095,3,Coolant,Temperature (G62),Range: -40.5...+135.0 ∞C\nSpecification (Warm): 80.0...110.0 ∞C
- 095,4,Intake Manifold,Change-Over,Range: IMC-V OFF/IMC-V ON
- ;
- 099,0,Lambda Control Shut-Off
- 099,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 099,2,Coolant,Temperature (G62),Range: -40.5...+135.0 ∞C\nSpecification (Warm): 80.0...110.0 ∞C
- 099,3,Lambda Control,,Range: -25.0...+25.0 %\nSpecification: -10.0...+10.0 %
- 099,4,Lambda Control,Status,Range: O2-Reg.OFF/O2-Reg.ON
- ;
- B099,0,Lambda Control Shut-Off
- ; "Activate" Basic Setting
- ; Wait until Field 4 shows "O2-Reg.OFF"
- B099,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- B099,2,Coolant,Temperature (G62),Range: -40.5...+135.0 ∞C\nSpecification (Warm): 80.0...110.0 ∞C
- B099,3,Lambda Control,,Range: -25.0...+25.0 %
- B099,4,Lambda Control,Status,Range: O2-Reg.OFF/O2-Reg.ON
- ;
- 100,0,Readiness Code
- 100,1,Readiness Bits,,xxxxxxx? = Catalytic Converter\nxxxxxx?x = Catalytic Converter Heater\nxxxxx?xx = Activated Charcoal System\nxxxx?xxx = Secondary Air Injection (AIR) System\nxxx?xxxx = A/C System\nxx?xxxxx = Oxygen Sensors\nx?xxxxxx = Oxygen Sensor Heating\n?xxxxxxx = Exhaust Gas Recirculation (EGR)
- 100,2,Coolant,Temperature (G62),Range: -40.5...+135.0 ∞C\nSpecification (Warm): 80.0...110.0 ∞C
- 100,3,Time since,Engine Start
- 100,4,OBD-Status,,xxxx00x? = Warm-Up Cycle not possible\nxxxx00?x = Warm-Up Cycle ended\nxxx?00xx = Malfunction detected (min. 1 Fault)\nxx?x00xx = Trip complete\nx?xx00xx = Driving Cycle detected\n?xxx00xx = MIL ON
- ;
- 101,0,Fuel Injection
- 101,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 101,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 101,3,Injection Timing,,Range: 0.0...20.0 ms
- 101,4,Mass Air Flow,Sensor (G70),Range: 0.0...200.0 g/s\nSpecification (Idle): 1.0...5.0 g/s\nSpecififcation (Load): min. 160.0 g/s
- ;
- 102,0,Fuel Injection
- 102,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 102,2,Coolant,Temperature (G62),Range: -40.5...+135.0 ∞C\nSpecification (Warm): 80.0...110.0 ∞C
- 102,3,Intake Air,Temperature (G42),Range: -48.0...+143.0 ∞C\nSpecification (Warm): < +80.0 ∞C (max. +115.0 ∞C)
- 102,4,Injection Timing,,Range: 0.0...20.0 ms
- ;
- 104,0,Fuel Injection (Start Adaption Values)
- 104,1,Engine Start,Temperature,Range: -40.5...+135.0 ∞C
- 104,2,Temperature,Adaptation Factor 1
- 104,3,Temperature,Adaptation Factor 2
- 104,4,Temperature,Adaptation Factor 3
- ;
- 107,0,Fuel Injection (Fuel Supply System)
- 107,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 107,2,Lambda Control,Bank 1,Range: -25.0...+25.0 %
- 107,3,Lambda Control,Bank 2,Range: -25.0...+25.0 %
- 107,4,Result,Lambda Control,Range: Test ON/Test OFF/Syst. OK/Syst. n.OK\nSpecification: Test OFF
- ;
- B107,0,Fuel Injection (Fuel Supply System)
- ; "Activate" Basic Setting
- ; Wait until Field 4 shows "Syst. OK"
- B107,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- B107,2,Lambda Control,Bank 1,Range: -25.0...+25.0 %
- B107,3,Lambda Control,Bank 2,Range: -25.0...+25.0 %
- B107,4,Result,Lambda Control,Range: Test ON/Test OFF/Syst. OK/Syst. n.OK\nSpecification: Syst. OK
- ;
- 110,0,Load Registration (Load/Full Throttle Enrichment)
- 110,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 110,2,Coolant,Temperature (G62),Range: -40.5...+135.0 ∞C\nSpecification (Warm): 80.0...110.0 ∞C
- 110,3,Injection Timing,,Range: 0.0...20.0 ms
- 110,4,Throttle Valve Angle,,Range: 0.0...100.0 %\nSpecification (Idle): 0.2...4.0 %
- ;
- 113,0,Load Registration (Load/Full Throttle Enrichment)
- 113,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 113,2,Engine Load,,Range: 0.0...100.0 %\nSpecification (Idle): 12.0...26.0 %
- 113,3,Throttle Valve Angle,,Range: 0.0...100.0 %\nSpecification (Idle): 0.2...4.0 %
- 113,4,Athmospheric,Pressure,Range: 500.0...1200.0 mbar\nSpecification (Error): ~1020.0 mbar
- ;
- 120,0,Traction Control (ASR)
- 120,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 120,2,Torque specified,by ASR,Range: 0.0...350.0 Nm
- 120,3,Engine Torque,(actual),Range: 0.0...350.0 Nm
- 120,4,Traction Control,Status,Specification: ASR OFF/ASR ON
- ;
- 122,0,Transmission
- 122,1,Engine Speed,(G28),Range: 0...6800 RPM\nSpecification (Idle): 620...860 RPM
- 122,2,Torque specified,by ASR,Range: 0.0...350.0 Nm
- 122,3,Engine Torque,(actual),Range: 0.0...350.0 Nm
- 122,4,Transmission,Status,Range: Torque red./No tor.red.
- ;
- 125,0,CAN-Databus Communication (Powertrain)
- 125,1,Transmission,Electronics (J217),Range: Transm. 1/Transm. 0\nSpecification: Transm. 1
- 125,2,Brake Electronics,(J104),Range: ABS 1/ABS 0\nSpecification: ABS 1
- 125,3,Instrument Cluster,(J285),Range: Instruments 1/Instruments 0\nSpecification: Instruments 1
- 125,4,Heating/Air,Condition (J255),Range: A/C 1/A/C 0\nSpecification: A/C 1
- ;
- 126,0,CAN-Databus Communication (Powertrain)
- 126,2,Steering Angle,Sensor (G85),Range: Steer. ang. 1/Steer. ang. 0\nSpecification: Steer. ang. 1
- 126,3,Airbag,(J234),Range: Airbag 1/Airbag 0\nSpecification: Airbag 1
- 126,4,Central,Electronics (J519),Range: Cent Elec 1/Cent Elec 0\nSpecification: Cent Elec 1
- ;
- 127,0,CAN-Databus Communication (Powertrain)
- 127,3,Steering Wheel,Electronics (J527),Range: St. Wheel 1/St. Wheel 0\nSpecification: St. Wheel 1
- ;
- ;
- ;---------------------------------------------------
- ;
- ; coding
- ;
- ;---------------------------------------------------
- ;
- ;
- C00,Engine Control Unit (J220) Coding
- C01,??xxx: Country/Emission
- C02,07 = North America (LEV)
- C03,xx?xx: Drivetrain/Additional Functions
- C04,0 = Front-Wheel-Drive w/o Anti-Slip-Regulation (ASR)
- C05,2 = All-Wheel-Drive w/o Anti-Slip-Regulation (ASR)
- C06,5 = Front-Wheel-Drive with Anti-Slip-Regulation (ASR) and Databus
- C07,7 = All-Wheel-Drive with Anti-Slip-Regulation (ASR) and Databus
- C08,xxx?x: Transmission
- C09,0 = 5-Speed Manual Transmission
- C10,5 = Automatic Transmission (01V/09A)
- C11,xxxx?: Vehicle Type
- C12,1 = B-Class (Audi A4 / VW Passat)
- C13,2 = C-Class (Audi A6)
- ;
- ;
- ;---------------------------------------------------
- ;
- ; login/coding-ii
- ;
- ;---------------------------------------------------
- ;
- ;
- L00,Engine Control Unit (J220) Coding-2
- L01,11463 = Cruise Control System (CCS) Activation
- L02,16167 = Cruise Control System (CCS) Deactivation
- ;
- ;
- ;---------------------------------------------------
- ;
- ; adaptation
- ;
- ;---------------------------------------------------
- ;
- ;
- A000,0,Reset Learned Values
- A000,5,Reset Learned Values
- A000,6,To Reset the learned Values Save this Adaptation Channel.
- ;
- A001,0,Idle Speed Adjustment
- A001,1,Engine Speed,(actual)
- A001,2,Engine Speed,(specified)
- A001,3,A/C Readiness,,Range: A/C-Low / A/C-High
- A001,4,A/C Compressor,,Range: Compr.OFF/Compr.ON
- ;
- A050,0,Immobilizer (Vehicle Data learning)
- A050,1,Status
- A050,5,Immobilizer (Vehicle Data learning)
- A050,6,Please enter the Immobilizer PIN/SKC of the Instrument Cluster (OLD PIN/SKC).
- A050,7,After that the Learning Process is being initiated the new Engine Control
- A050,8,Module adopts the Vehicle-Identification-Number (VIN) and Immobilizer
- A050,9,Identification (IMMO-ID) of the Vehicle (from the OLD Instrument Cluster).
- A050,10,Once the Adaptation is done switch the Ignition OFF for about 2 Minutes.
- ;
- A091,0,Immobilizer Status
- A091,5,Immobilizer Status (Read Only)
- A091,6,0 = Immobilizer not matched (NEW)
- A091,7,1 = Immobilizer disabled
- A091,8,4 = Immobilizer matched (System OK)
- ;
- ;
- ;---------------------------------------------------
- ;
- ; readiness
- ;
- ;---------------------------------------------------
- ;
- ;
- O,078-907-551-ATQ
- ;
- SN,ME 7.1
- ;
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement