tenda

Decompressing...done
Found ST compatible serial flash with 256 64KB blocks; total size 16MB


CFE version 9.10.178.27 (r584393) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: Wed Feb 15 04:19:27 EST 2017 (root@linux-tdxn)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 392 MHz
Info: DDR frequency set from clkfreq=900,*392*
bcm_robo_enable_switch: EEE is disabled
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 9.10.178.27 (r584393)
CPU type 0x0: 900MHz
Tot mem: 65536 KBytes

CFE mem:    0x00F00000 - 0x017A367C (9057916)
Data:       0x00F6BA24 - 0x00F6C05C (1592)
BSS:        0x00F6C068 - 0x00FA167C (218644)
Heap:       0x00FA167C - 0x017A167C (8388608)
Stack:      0x017A167C - 0x017A367C (8192)
Text:       0x00F00000 - 0x00F5F8EC (391404)
Boot:       0x017A4000 - 0x017E4000
Reloc:      I:00000000 - D:00000000

Mac:4-95-e6-28-4f-20
Device eth0:  hwaddr 04-95-E6-28-4F-20, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
upgrade wait time is 3s
**upgrade_wait over!
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .... 4133088 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
[    0.890000] console [ttyS0] enabled, bootconsole disabled
[    0.910000] brd: module loaded
[    0.920000] loop: module loaded
[    0.920000] pflash: found no supported devices
[    0.930000] bcmsflash: squash filesystem found at block 28
[    0.930000] Creating 7 MTD partitions on "bcmsflash":
[    0.940000] 0x000000000000-0x000001000000 : "All"
[    0.940000] 0x000000000000-0x000000040000 : "Bootloader"
[    0.950000] 0x000000040000-0x000000fd0000 : "KernelFS"
[    0.950000] 0x0000001ceb08-0x000000fd0000 : "rootfs"
[    0.960000] 0x000000fd0000-0x000000fe0000 : "CFM_BACKUP"
[    0.960000] 0x000000fe0000-0x000000ff0000 : "CFM"
[    0.970000] 0x000000ff0000-0x000001000000 : "nvram"
[    0.970000] nflash: found no supported devices
[    0.980000] PPP generic driver version 2.4.2
[    0.980000] PPP Deflate Compression module registered
[    0.990000] PPP BSD Compression module registered
[    0.990000] PPP MPPE Compression module registered
[    1.000000] NET: Registered protocol family 24
[    1.000000] Initializing USB Mass Storage driver...
[    1.010000] usbcore: registered new interface driver usb-storage
[    1.010000] USB Mass Storage support registered.
[    1.020000] u32 classifier
[    1.020000]     Actions configured
[    1.020000] Netfilter messages via NETLINK v0.30.
[    1.030000] nf_conntrack version 0.5.0 (939 buckets, 3756 max)
[    1.030000] [BM CORE     ]  INFO: online ip data hash table created, size = 199
[    1.040000] [BM CORE     ]  INFO: online_ip proc file created
[    1.040000] ctnetlink v0.93: registering with nfnetlink.
[    1.050000]  create /proc/behavior/emailbcc SUCCESSFULLY.
[    1.050000] netfilter smtp init successfully
[    1.060000] xt_time: kernel timezone is -0000
[    1.060000] Kernel:Init flow dev success.
[    1.060000] IPv4 over IPv4 tunneling driver
[    1.070000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.070000] TCP cubic registered
[    1.080000] NET: Registered protocol family 17
[    1.080000] L2TP core driver, V2.0
[    1.080000] PPPoL2TP kernel driver, V2.0
[    1.090000] L2TP IP encapsulation support (L2TPv3)
[    1.090000] L2TP netlink interface
[    1.090000] L2TP ethernet pseudowire support (L2TPv3)
[    1.100000] 802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
[    1.100000] All bugs added by David S. Miller <[email protected]>
[    1.150000] Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
[    1.160000] brcmnand: found no supported devices
[    1.170000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    1.180000] devtmpfs: mounted
[    1.190000] Freeing init memory: 192K
[    1.200000] Failed to execute /sbin/preinit.  Attempting defaults...
mkdir: can't create directory '/var/run': File exists
[    3.210000] [BM CORE     ]  INFO: bm_init success
[    3.210000] bm_debug_init_proc success!
[    3.210000] [U2K MODULE  ]  INFO: bm_u2k_info_init success
[    3.290000] [MAC FILTER  ]  INFO: bm_mac_filter init success
[    3.390000] [PRIVILEGE IP]  INFO: privilege ip init success
[    3.490000] qos qos_init 1627: qos module init success
[    3.570000] OS TYPE INIT FINISHED
[    3.570000] [URL FILTER  ]  INFO: url filter init success
[    3.690000] fastnatconf fastnat_conf_init 611: fastnat conf module init success
[    3.910000] udevd (371): /proc/371/oom_adj is deprecated, please use /proc/371/oom_score_adj instead.
init_core_dump 1816: rlim_cur = 0, rlim_max = -1
init_core_dump 1825: open core dump success
init_core_dump 1834: rlim_cur = 5242880, rlim_max = 5242880
func:InitCfm begin load_mib....
flash_read:ret = 65536
crc = cfa6c00e, newcrc = cfa6c00e
flash_read:ret = 65536
crc = 2be5f59, newcrc = 2be5f59

######## STARTING PROGRAM #########
flash_read:ret = 65536
crc = 2be5f59, newcrc = 2be5f59
spawn-fcgi: child spawned successfully: PID: 384
Give root password for system maintenance
(or type Control-D for normal startup):flash_to_file:open Policy failed.
going to rewrite flash...
open /etc/policy_bak.cfg failed.
rewrite flash ok...
failure to open policy source: /etc/policy.cfg
left wan[0]:0
left lan[0]:1
left lan[1]:2
left lan[2]:3
left lan[3]:4
vlan_array[0]: value 1  index_num 1 name eth1 cpu_port 5index[0] 0  index[1] 0  index[2] 0  index[3] 0  index[4] 0
vlan_array[1]: value 0  index_num 4 name eth0 cpu_port 8index[0] 1  index[1] 2  index[2] 3  index[3] 4  index[4] 0
vlan_array[2]: value -2  index_num 0 name  cpu_port 0index[0] 0  index[1] 0  index[2] 0  index[3] 0  index[4] 0
vlan_array[3]: value -2  index_num 0 name  cpu_port 0index[0] 0  index[1] 0  index[2] 0  index[3] 0  index[4] 0
vlan_array[4]: value -2  index_num 0 name  cpu_port 0index[0] 0  index[1] 0  index[2] 0  index[3] 0  index[4] 0
nvram unset vlan1ports
nvram unset vlan2ports
nvram unset vlan3ports
nvram unset vlan4ports
nvram unset vlan5ports
nvram set vlan2ports="0  5*"
nvram set vlan1ports="1  2  3  4  8*"
#IPTV STB VLAN I[    5.310000] zzj++:cmd:GPIO_IOC_REG_USB_LED
D mode is disable!#
main=>116:init server success.1..
No need to start gpio thread.
[    5.380000] et: module license 'Proprietary' taints kernel.
[    5.390000] Disabling lock debugging due to kernel taint
[    5.410000] et_module_init: passivemode set to 0x0
[    5.420000] et_module_init: txworkq set to 0x0
[    5.420000] et_module_init: et_txq_thresh set to 0xce4
[    5.430000] et_module_init: et_rxlazy_timeout set to 0x3e8
[    5.430000] et_module_init: et_rxlazy_framecnt set to 0x20
[    5.510000] stbport=4=wanport=0=
[    5.520000] bcm_robo_enable_switch: EEE is disabled
[    5.530000] eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 9.10.178.27 (r584393)
[    5.550000] eth1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 9.10.178.27 (r584393)
insmod: can't read '/lib/modules/2.6.36.4brcmarm/kernel/drivers/net/proxyarp/proxyarp.ko': No such file or directory
[    7.360000] wl_module_init: passivemode set to 0x0
[    7.370000] wl_module_init: txworkq set to 0x0
[    7.390000] External imprecise Data abort at addr=0x1f4fc, fsr=0x1c06, pc=0x7f169160 lr=0x801fdf6c ignored.
[    7.400000] External imprecise Data abort at addr=0x1f4fc, fsr=0x1c06, pc=0x7f0bc1f8 lr=0x801fdf6c ignored.
[    7.420000] eth2: Broadcom BCM43c8 802.11 Wireless Controller 9.10.178.27 (r584393 WLTEST)
[    7.430000] PCI: Enabling device 0001:01:00.0 (0140 -> 0142)
[    7.470000] eth3: Broadcom BCM43227 802.11 Wireless Controller 9.10.178.27 (r584393 WLTEST)
insmod: can't read '/lib/modules/2.6.36.4brcmarm/kernel/drivers/usb/core/usbcore.ko': No such file or directory
[    7.530000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.550000] ehci_hcd 0000:00:04.1: EHCI Host Controller
[    7.550000] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
[    7.590000] ehci_hcd 0000:00:04.1: irq 36, io mem 0x18004000
[    7.610000] ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
[    7.610000] hub 1-0:1.0: USB hub found
[    7.640000] hub 1-0:1.0: 2 ports detected
add
[    7.750000] hub 1-0:1.0: over-current change on port 1
add
[    7.800000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.810000] ohci_hcd 0000:00:04.0: OHCI Host Controller
[    7.820000] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
[    7.820000] ohci_hcd 0000:00:04.0: irq 36, io mem 0x1800d000
[    7.890000] hub 2-0:1.0: USB hub found
add
[    7.910000] hub 2-0:1.0: 2 ports detected
insmod: can't read '/lib/modules/2.6.36.4brcmarm/kernel/drivers/usb/storage/usb-storage.ko': No such file or directory
add
insmod: can't read '/lib/modules/2.6.36.4brcmarm/kernel/drivers/usb/class/usblp.ko': No such file or directory
insmod: can't read '/lib/modules/2.6.36.4brcmarm/kernel/drivers/usb/host/xhci-hcd.ko': No such file or directory
[    8.050000] Hello,This is the USB LED handling Driver
[    8.060000] >>si_gpioreserve : 0xffffffff
[    8.060000] >>si_gpiocontrol : 0x0
[    8.070000] >>si_gpioouten : 0x8546
[    8.070000] >>si_gpioout : 0x106
sh: can't create /proc/irq/163/smp_affinity: nonexistent directory
sh: can't create /proc/irq/169/smp_affinity: nonexistent directory
ifconfig: SIOCSIFHWADDR: No such device
ifconfig: SIOCGIFFLAGS: No such device
### set br0 mac [04:95:e6:28:4f:20]### [5]
##############add vlan devices [vconfig add eth1 2]
##############add vlan devices [vconfig add eth0 1]
[    8.370000] device eth1 entered promiscuous mode
ifconfig: SIOCSIFHWADDR: No such device
[    8.480000] device vlan1 entered promiscuous mode
[    8.480000] device eth0 entered promiscuous mode
[    8.500000] br0: topology change detected, propagating
[    8.510000] br0: port 1(vlan1) entering forwarding state
[    8.510000] br0: port 1(vlan1) entering forwarding state
[    8.530000] IPv4 FIB: Using LC-trie version 0.409
Sat Jan  1 00:00:00 UTC 2000
Loading dnrd...
killall: dnrd: no process killed
[compatibility:is_compatible:80] The software is compatible!
_eval 98: child process create success
_eval 98: child process create success
_start_time_check 202: time_check register success, register_pid = 526
_eval 94: child process status is 0
_start_httpd 219: httpd register success, register_pid = 527
_eval 94: child process status is 0
_start_multiwan 283: _start_multiwan register success, register_pid = 528
_eval 94: child process status is 0
_start_ucloud_v2 357: ucloud_v2 register success, register_pid = 529
_eval 94: child process status is 0
_start_buisness_proc 383: buisness_proc register success, register_pid = 530
_eval 94: child process status is 0
_start_auto_discover 237: _start_auto_discover register success, register_pid = 531
business_proc
ucloud_v2
httpd
multiWAN
netctrl
auto_discover
time_check
[TIMER_CHECK >>time_check_reboot_info_printf(51)]:               enable:1
[TIMER_CHECK >>time_check_reboot_info_printf(52)]:               type:1
[TIMER_CHECK >>time_check_reboot_info_printf(57)]:               wday_en:1;1;1;1;1;1;1
[TIMER_CHECK >>time_check_reboot_info_printf(58)]:               start_time:03:00
[TIMER_CHECK >>time_check_reboot_info_printf(59)]:               end_time:05:00
[TIMER_CHECK >>time_check_reboot_info_printf(60)]:               max_speed:3
[TIMER_CHECK >>time_check_reboot_info_printf(61)]:               check_speed=3000
[TIMER_CHECK >>time_check_reboot_info_printf(62)]:               wan_ifnames:vlan2
[TIMER_CHECK >>time_check_power_info_printf(50)]:                enable:0
[TIMER_CHECK >>time_check_power_info_printf(51)]:                type:1
[TIMER_CHECK >>time_check_power_info_printf(56)]:                wday_en:1;1;1;1;1;1;1
[TIMER_CHECK >>time_check_power_info_printf(57)]:                start_time:00:00
[TIMER_CHECK >>time_check_power_info_printf(58)]:                end_time:07:00
[TIMER_CHECK >>time_check_power_info_printf(59)]:                max_speed:3
[TIMER_CHECK >>time_check_power_info_printf(60)]:                check_speed=3000
wl2g_op:0 wl5g_op:0
fopen: No such file or directory
init_core_dump 1816: rlim_cur = 5242880, rlim_max = 5242880
init_core_dump 1825: open core dump success
init_core_dump 1834: rlim_cur = 5242880, rlim_max = 5242880
init_core_dump 1816: rlim_cur = 5242880, rlim_max = 5242880
init_core_dump 1825: open core dump success
init_core_dump 1834: rlim_cur = 5242880, rlim_max = 5242880
logserver.c check network 192.168.0.1 success
######## RECEIVING DATA #########
init_core_dump 1816: rlim_cur = 5242880, rlim_max = 5242880
init_core_dump 1825: open core dump success
init_core_dump 1834: rlim_cur = 5242880, rlim_max = 5242880


Yes:

      ****** WeLoveLinux******

 Welcome to ...
init_core_dump 1816: rlim_cur = 5242880, rlim_max = 5242880
init_core_dump 1825: open core dump success
init_core_dump 1834: rlim_cur = 5242880, rlim_max = 5242880
create socket  fail -1
[httpd][debug]----------------------------webs.c,157
httpd listen ip = 192.168.0.1 port = 80
webs: Listening for HTTP requests at address 192.168.0.1
RTNETLINK answers: Operation not supported
sh: can't create /proc/br0_ip: nonexistent directory
Register USB with RET: 0
[   11.890000] max_new_conntrack=4000
[   12.040000] fastnatconf fastnat_conf_proc_port_add 350: layer = 3, port = 443, protocol = 6
[   12.060000] fastnatconf fastnat_conf_add_port 136: add success port = 443, protocol = 6, layer = 3
[   12.070000] fastnatconf fastnat_conf_proc_port_add 350: layer = 2, port = 53, protocol = 17
[   12.090000] fastnatconf fastnat_conf_add_port 136: add success port = 53, protocol = 17, layer = 2
Debug->tpi_port.c: tpi_port_handle(61)--type = 0
Debug->tpi_port.c: tpi_port_mode_set(12)--wan_num=1
Debug->tpi_port.c: tpi_port_mode_set(14)--wan[0].portmode=0
sh: nkgw: not found
set port 0 to AUTO
[ DEBUG ] ******Sucessed to change lan config! ******
killall: dhttpd: no process killed
ifconfig: SIOCSIFFLAGS: Cannot assign requested address
ifconfig: SIOCSIFFLAGS: Cannot assign requested address
[mac_vendor_init : 141] mac vendor list init OK!
arp task satrt:
nbns task start:
iptables: No chain/target/match by that name.
[VENDOR_DEBUG _____check_vendor_network(125)______]:Get host error!
vendor_task[165]    check vendor network failed!
********************************
        goahead  3.3.0 start
********************************
goahead: 4: main----51

goahead: 4: initPlatform----398

goahead: 4: websOpen----233

iptables v1.4.12.2: Couldn't load target `dmz_forward_pre':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.12.2: Couldn't load target `vpnserver':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables v1.4.12.2: Couldn't load target `dmz_forward_post':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: Index of insertion too big.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.12.2: Couldn't load target `port_forward_pre':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.12.2: Couldn't load target `port_forward_post':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
[VENDOR_DEBUG _____make_packet(118)______]:new_mac is: 2c-4d-54-4c-b3-86
[VENDOR_DEBUG _____communication_with_cloud(84)______]:Get host error!
[VENDOR_DEBUG _____get_vendor_from_cloud(165)______]:Communication Failed
[VENDOR_DEBUG _____get_device_vendor(228)______]:Unlucky! No vendor info
[VENDOR_DEBUG _____make_packet(118)______]:new_mac is: fc-7c-02-d5-1a-cd
[VENDOR_DEBUG _____communication_with_cloud(84)______]:Get host error!
[VENDOR_DEBUG _____get_vendor_from_cloud(165)______]:Communication Failed
[VENDOR_DEBUG _____get_device_vendor(228)______]:Unlucky! No vendor info
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.12.2: Couldn't load target `icmp_drop':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
goahead: 0: Can't get host address for host Tenda: errno 97, use Local:127.0.0.1
cgi/main.c check network 172.18.166.182 success
dlan_ip:172.18.166.182
endpoint[http://172.18.166.182:80]
iptables: No chain/target/match by that name.
iptables v1.4.12.2: Couldn't load target `web_wanadmin':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.12.2: Couldn't load target `web_wanadmin':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.12.2: Couldn't load target `access_ctrl':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
killall: 3322ip: no process killed
iptables: No chain/target/match by that name.
killall: 88ip: no process killed
killall: gnway: no process killed
mdns task start:
killall: inadyn: no process killed
rm: can't remove '/etc/ddns_*': No such file or directory
[VENDOR_DEBUG _____make_packet(118)______]:new_mac is: b8-22-4f-3a-e4-a3
[VENDOR_DEBUG _____communication_with_cloud(84)______]:Get host error!
[VENDOR_DEBUG _____get_vendor_from_cloud(165)______]:Communication Failed
[VENDOR_DEBUG _____get_device_vendor(228)______]:Unlucky! No vendor info
iptables: No chain/target/match by that name.
iptables v1.4.12.2: Couldn't load target `MINIUPNPD':No such file or directory

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
miniupnpd.c,865,ver=1.0,osname=Wireless Router,osver=1.0,osurl=http://192.168.0.1,manuft=Tenda,descri=
###fd failed to recv packet!###
##### NO SERVER FOUND! #####
RTNETLINK answers: No such file or directory
dhcpsCfgToStruct 555: lan type is
dhcps_lan_dhcpc_configure 272: lan dhcp client not get ip
[url_filt[   19.900000] [URL FILTER  ]  INFO: g_uf_enable = disable
er:apply_url_filter_global_option:339] filter.url.en == 0
[url_filt[   19.940000] [URL FILTER  ]  INFO: g_uf_enable = disable
er:apply_url_filter_global_optio[   19.940000] [MAC FILTER  ]  INFO: g_mac_filter_enable = disable, mf_default_action = accept
n:339] filter.url.en == 0
[   19.950000] [MAC FILTER  ]  INFO: g_mac_filter_enable = disable, mf_default_action = accept

[mac_filter:load_mac_global_options:381] macfilter.mode == black
[mac_filter:load_mac_filter_cfg:442] macfilter.black.id count == 0
[mac_filter:load_parent_control_cfg:507] parent.control.id count ==[   19.980000] qos qos_rcv_msg 261: ------APPLY---
 0
[[   19.980000] qos qos_rule_apply 526: g_qos_enable = disable
mac_filter:refresh_mac_filter_to_kernel:573] l_mac_filter_changed: 1; l_mac_filter.enable[   19.990000] qos qos_rcv_msg 289: ------AUTO_APPLY---
: 0
[mac_filter:apply_mac_filter_global_option:558] enable:0; black_white: 0
[mac_filter:apply_mac_filter_global_option:558] enable:0; black_white: 0
[   20.020000] qos set_wan_if 1086: wanid=0 up_rate=1024000 down_rate=0
[   20.020000] qos set_wan_if 1086: wanid=1 up_rate=0 down_rate=0
[   20.040000] qos set_wan_if 1086: wanid=2 up_rate=0 down_rate=0
[   20.040000] qos set_wan_if 1086: wanid=3 up_rate=0 down_rate=0
[   20.100000] Init gsbmac dev success.
[   20.110000] The ARP attack defence is init v1 successful
killall: arpbrocast: no process killed
[   20.170000] Kernel:Init attack fence dev success.
[   20.180000] the ddos ip attack defnence init successful
[   20.190000] SET_LAN_PARAM_DATA k_data:
[   20.190000]  lan ip:3232235521
[   20.190000]  lan mask:4294967040
[   20.200000]  lan submask:3232235520
[   20.200000]  lan interface:br0
[   20.200000]  lan http port:80
icmp is 1,1500,u[   20.210000] set the proceee ture
dp is 1,1500,tcp[   20.210000] SET_IPOP_FENCE_ATTACK_DATA k_data:
_syn is 1,1500
[   20.220000]  ip options:32512
[   20.220000] SET_BAD_PKT_FENCE_ATTACK_DATA k_data:
[   20.220000]  bad pkt:248
[   20.230000] SET_DDOS_FENCE_ATTACK_DATA k_data:
[   20.230000]  status:7
[   20.230000]  tcp threshold:1500
[   20.240000]  udp threshold:1500
[   20.240000]  icmp threshold:1500
---------->>[ start_wifi, wl_rate=24 ]
65370728
[ ERROR ] invalid access mode:
CJ+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++set wl1 value = auto
killall: wps_monitor: no process killed
killall: nas: no process killed
killall: eapd: no process killed
[ DEBUG ] len=0,lan1_ifnames =
[ ERROR ] Do not exsit ifname of guest_network,do nothing!
killall: acsd: no process killed
[   21.160000] CJ++ init gpioouten in hw_init status 1
eth3: cmd=231: Invalid argument
eth3: WLC_SET_VAR(chanspec): Invalid argument
eth3: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth3: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth3: WLC_SET_VAR(ampdu_retry_limit_tid): O[   21.340000] CJ++ init gpioouten in hw_init status 1
peration not supported
eth3: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth3: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth3: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth3: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth3: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth3: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth[   21.380000] device eth3 entered promiscuous mode
3: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth3: WLC_SET_VAR(ampdu_rr_re[   21.390000] br0: topology change detected, propagating
try_limit_tid): [   21.400000] br0: port 2(eth3) entering forwarding state
Operation not su[   21.400000] br0: port 2(eth3) entering forwarding state
pported
eth3: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth3: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth3: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth3: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth3: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth3: WLC_SET_VAR(avg_dma_xfer_rate): Operation not supported
eth3: WLC_SET_VAR(taf): Operation not supported
Invalid instance identifier br0

[   21.570000] wisp or APC is close
eth2: WLC_GET_VAR(psta_if): Invalid argument
[ DEBUG ] len=0,lan1_ifnames =
[ ERROR ] Do not exsit ifname of guest_network,do nothing!
===name(eth2) unit(0)===
td_acs >>td_acs_init_dev_name(2976): ifname eth2: radio is on
td_acs >>td_acs_init_dev_name(2986): ifname eth2: auto channel is enable
===name(eth3) unit(1)===
td_acs >>td_acs_init_dev_name(2976): ifname eth3: radio is on
td_acs >>td_acs_init_dev_name(2986): ifname eth3: auto channel is enable
td_acs >>td_acs_init_cfg(594): set invalid ch:12
td_acs >>td_acs_init_cfg(594): set invalid ch:13
td_acs >>td_acs_init_cfg(610): noise_th=(-88, -65) busy_th=(20, 73) loop(1) cs_timer(900s)
eth2: WLC_GET_VAR(bw_cap): Invalid argument
td_acs >>td_acs_init_rsi(654): failed to get bw_capret code: -1
td_acs >>td_acs_info_init(735): dev(eth2) acs_init_rsi fail
====td_acs_exit====
---------->>[ start_wifi, wl_rate=5 ]
65370728
[ ERROR ] invalid access mode:
[ ERROR ] coutry_code=CN
CJ+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++set wl0 value = auto
[ DEBUG ] len=0,lan1_ifnames =
[ ERROR ] Do not exsit ifname of guest_network,do nothing!
killall: acsd: n[   23.030000] CJ++ init gpioouten in hw_init status 1
o process killed
eth2: cmd=231: Invalid argument
eth2: WLC_SET_VAR(chanspec): Invalid argument
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Oper[   23.160000] CJ++ init gpioouten in hw_init status 1
ation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_[   23.230000] device eth2 entered promiscuous mode
retry_limit_tid)[   23.240000] br0: topology change detected, propagating
: Operation not [   23.240000] br0: port 3(eth2) entering forwarding state
supported
eth2:[   23.250000] br0: port 3(eth2) entering forwarding state
 WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
eth2: WLC_SET_VAR(avg_dma_xfer_rate): Operation not supported
eth2: WLC_SET_VAR(taf): Operation not supported
eth2: cmd=64: Operation not supported
Invalid instance identifier br0

device br1 already exists; can't create bridge with the same name
[   23.340000] wisp or APC is close
[ DEBUG ] len=0,lan1_ifnames =
[ ERROR ] Do not exsit ifname of guest_network,do nothing!
===name(eth2) unit(0)===
td_acs >>td_acs_init_dev_name(2976): ifname eth2: radio is on
td_acs >>td_acs_init_dev_name(2986): ifname eth2: auto channel is enable
===name(eth3) unit(1)===
td_acs >>td_acs_init_dev_name(2976): ifname eth3: radio is on
td_acs >>td_acs_init_dev_name(2986): ifname eth3: auto channel is enable
td_acs >>td_acs_init_cfg(594): set invalid ch:12
td_acs >>td_acs_init_cfg(594): set invalid ch:13
td_acs >>td_acs_init_cfg(610): noise_th=(-88, -65) busy_th=(20, 73) loop(1) cs_timer(900s)
td_acs >>td_acs_init_rsi(662): band_type:1 bw_cap: 7 coex_enb:1
td_acs >>td_acs_init_width_level(712): Width level: 5g_80=40, 5g_40=73.
Interface eth2 scan channels: 36, 40, 44, 48, 149, 153, 157, 161, 165
===td_acs_scan_timer_func==(eth2)==
td_acs >>td_acs_scan_timer_func(2087): band_type:1 bw_cap: 7 coex_enb:1
td_acs_scan_prep: passive_time=250
td_acs >>td_acs_scan_prep(790): scan channel number: 13
td_acs >>td_acs_scan_prep(793): params size: 90
td_acs: (eth2) scan in progress ...
td_acs: (eth2) scan in progress ...
td_acs: (eth2) scan in progress ...
td_acs: (eth2) scan in progress ...
td_acs: (eth2) scan in progress ...
td_acs: (eth2) scan in progress ...
td_acs: (eth2) scan in progress ...
td_acs: (eth2) scan in progress ...
td_acs: (eth2) scan in progress ...
td_acs >>td_acs_get_scan(974): list->count: 0, list->buflen: 12
td_acs >>td_acs_adjust_second_chan(1727): ctrl_ch:40 middle: 0=38 1=42
td_acs >>td_acs_adjust_second_chan(1751): selected mid: 0=38
td_acs >>td_acs_adjust_second_chan(1762): Final selected chanspec: 0xd926
td_acs >>td_acs_run_scan_select(2019): [AUTO_CHANNEL] select chanspec d926(#40)
td_acs: [2000/01/01 00:00:17]: WiFi 5G(eth2) bandwidth change from 40MHz to 80MHz, reason busy=0
td_acs >>td_acs_adjust_bandwidth(1960): Last adjust bandwidth chanspec is 0xe12a(#40).
td_acs: selected_chspec=0xe12a
td_acs >>td_acs_init_cfg(594): set invalid ch:12
td_acs >>td_acs_init_cfg(594): set invalid ch:13
td_acs >>td_acs_init_cfg(610): noise_th=(-88, -65) busy_th=(20, 73) loop(1) cs_timer(900s)
td_acs >>td_acs_init_rsi(662): band_type:2 bw_cap: 3 coex_enb:1
td_acs >>td_acs_init_width_level(695): Width level: 2g_40=3, 2g_20=26.
Interface eth3 scan channels: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13
===td_acs_scan_timer_func==(eth3)==
td_acs >>td_acs_scan_timer_func(2087): band_type:2 bw_cap: 3 coex_enb:1
td_acs_scan_prep: passive_time=250
td_acs >>td_acs_scan_prep(790): scan channel number: 13
td_acs >>td_acs_scan_prep(793): params size: 90
td_acs: (eth3) scan in progress ...
td_acs: (eth3) scan in progress ...
td_acs: (eth3) scan in progress ...
td_acs: (eth3) scan in progress ...
td_acs: (eth3) scan in progress ...
td_acs: (eth3) scan in progress ...
td_acs: (eth3) scan in progress ...
td_acs: (eth3) scan in progress ...
td_acs: (eth3) scan in progress ...
td_acs: (eth3) scan in progress ...
td_acs: (eth3) scan in progress ...
td_acs: (eth3) scan in progress ...
td_acs: (eth3) scan in progress ...
td_acs >>td_acs_get_scan(974): list->count: 0, list->buflen: 12
td_acs >>td_acs_run_scan_select(2019): [AUTO_CHANNEL] select chanspec 1001(#1)
td_acs: [2000/01/01 00:00:21]: WiFi 2.4G(eth3) bandwidth change from 20MHz to 40MHz, reason busy=0
td_acs >>td_acs_adjust_bandwidth(1960): Last adjust bandwidth chanspec is 0x1803(#1).
td_acs: selected_chspec=0x1803
msg str: [cfm Post time_check 4?relate_module_id=19,string_info=first_time_start]
[TIMER_CHECK >>init_time_check_module_var(146)]:key = relate_module_id,value = 19
[TIMER_CHECK >>init_time_check_module_var(154)]:key = string_info,value = first_time_start
tpi_sntp_handle(99): start sntp...
tpi_set_user_policy,35: entry count:0
systime_server = 211.138.200.208
main,335,sntp_en =1,tz=20.00,checktime=86400
[ DEBUG ] lan dhcp not enable
cp: can't stat '/etc/smb.conf': No such file or directory
[2000/01/01 00:00:21] log_init:1707: warn: unknown level in debug string: (null), use default_log_level.
[ DEBUG ] *****netctrl init module entries ok.*****
create socket  fail -1
create socket  fail -1
create socket  fail -1
sh: u_yunsafe: not found
2G rxctl bug detected[1] ....
rxctl_detect reinit
2G rxctl bug detected[2] ....
rxctl_detect reinit
2G rxctl bug detected[3] ....
rxctl_detect reinit
2G rxctl bug detected[4] ....