[wip:20190130] OpenBSD-current on pcDuino (Allwinner A10)

OpenBSD 6.4-current (GENERIC) #4: Wed Jan 30 09:24:32 JST 2019
    [email protected]:/usr/src/sys/arch/armv7/compile/GENERIC
real mem  = 981217280 (935MB)
avail mem = 951930880 (907MB)
mainbus0 at root: LinkSprite pcDuino
cpu0 at mainbus0: ARM Cortex-A8 r3p2 (ARMv7)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(64b/l,4way) I-cache, 32KB(64b/l,4way) wr-back D-cache
sxiccmu0 at mainbus0
simplebus0 at mainbus0: "soc"
sxiccmu1 at simplebus0
sxipio0 at simplebus0: 175 pins
sxitimer0 at simplebus0: cntrtimer @ 24000KHz
"sram-controller" at simplebus0 not configured
"dma-controller" at simplebus0 not configured
sxie0 at simplebus0, address 02:96:07:40:b2:42
rlphy0 at sxie0 phy 1: IP101 10/100 PHY, rev. 4
"mdio" at simplebus0 not configured
"lcd-controller" at simplebus0 not configured
"lcd-controller" at simplebus0 not configured
sximmc0 at simplebus0
sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
"usb" at simplebus0 not configured
"phy" at simplebus0 not configured
ehci0 at simplebus0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1
ohci0 at simplebus0splassert: ohci_fdt_attach: want 5 have 0
: version 1.0
"crypto-engine" at simplebus0 not configured
ehci1 at simplebus0
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1
ohci1 at simplebus0: version 1.0
"clock" at simplebus0 not configured
sxiintc0 at simplebus0
"pinctrl" at simplebus0 not configured
"timer" at simplebus0 not configured
sxidog0 at simplebus0
sxirtc0 at simplebus0
"eeprom" at simplebus0 not configured
sxits0 at simplebus0
com0 at simplebus0: ns16550, no working fifo
com0: console
sxitwi0 at simplebus0
iic0 at sxitwi0
axppmic0 at iic0 addr 0x34: AXP209
"display-frontend" at simplebus0 not configured
"display-frontend" at simplebus0 not configured
"display-backend" at simplebus0 not configured
"display-backend" at simplebus0 not configured
gpio0 at sxipio0: 32 pins
gpio1 at sxipio0: 32 pins
gpio2 at sxipio0: 32 pins
gpio3 at sxipio0: 32 pins
gpio4 at sxipio0: 32 pins
gpio5 at sxipio0: 32 pins
gpio6 at sxipio0: 32 pins
gpio7 at sxipio0: 32 pins
gpio8 at sxipio0: 32 pins
usb2 at ohci0: USB revision 1.0
uhub2 at usb2 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci1: USB revision 1.0
uhub3 at usb3 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, 00000, 0010> SCSI2 0/direct removable
sd0: 7588MB, 512 bytes/sector, 15540224 sectors
run0 at uhub1 port 1 configuration 1 interface 0 "Ralink 802.11 n WLAN" rev 2.00/1.01 addr 2
run0: MAC/BBP RT3070 (rev 0x0201), RF RT3020 (MIMO 1T1R), address 00:01:8e:cb:a3:ef
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on sd0a (f885e57b6161d89e.a) swap on sd0b dump on sd0b
WARNING: preposterous clock chip time
WARNING: CHECK AND RESET THE DATE!