Pteridium

Untitled

Nov 26th, 2013
82
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. CFE version 1.0.37-105.22-1 for BCM96368 (32bit,SP,BE)
  2. Build Date: Fri Mar 19 11:53:33 CST 2010 (jojopo@broadcom_v060.comtrend.com)
  3. Copyright (C) 2000-2009 Broadcom Corporation.
  4.  
  5. Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB
  6. Total Flash size: 8192K with 135 sectors
  7. Chip ID: BCM6368B2, MIPS: 400MHz
  8. Main Thread: TP0
  9. Total Memory: 67108864 bytes (64MB)
  10. Boot Address: 0xb8000000
  11.  
  12. Board IP address : 192.168.1.1:ffffff00
  13. Host IP address : 192.168.1.100
  14. Gateway IP address :
  15. Run from flash/host (f/h) : f
  16. Default host run file name : vmlinux
  17. Default host flash file name : bcm963xx_fs_kernel
  18. Boot delay (0-9 seconds) : 1
  19. Board Id (0-14) : 96368M-1341N
  20. Number of MAC Addresses (1-32) : 11
  21. Base MAC Address : 64:68:0c:
  22. PSI Size (1-64) KBytes : 24
  23. Enable Backup PSI [0|1] : 0
  24. System Log Size (0-256) KBytes : 0
  25. Main Thread Number [0|1] : 0
  26.  
  27. *** Press any key to stop auto run (1 seconds) ***
  28. Auto run second count down: 0
  29. Booting from only image (0xb8010000) ...
  30. Code Address: 0x80010000, Entry Address: 0x80010000
  31. LZMA: Prossible old LZMA format, trying to decompress..
  32. Decompression OK!
  33. Entry at 0x80010000
  34. Closing network.
  35. Disabling Switch ports.
  36. Flushing Receive Buffers...
  37. 0 buffers found.
  38. Closing DMA Channels.
  39. Starting program at 0x80010000
  40. [ 0.000000] Linux version 3.3.8 (taxodium@debian) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38917) ) #4 SMP Tue 3
  41. [ 0.000000] Detected Broadcom 0x6368 CPU revision b2
  42. [ 0.000000] CPU frequency is 400 MHz
  43. [ 0.000000] 64MB of RAM installed
  44. [ 0.000000] registering 38 GPIOs
  45. [ 0.000000] gpiochip_add: registered GPIOs 0 to 37 on device: bcm63xx-gpio
  46. [ 0.000000] board_bcm963xx: Boot address 0xb8000000
  47. [ 0.000000] board_bcm963xx: CFE version: 1.0.37-105.22
  48. [ 0.000000] bootconsole [early0] enabled
  49. [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
  50. [ 0.000000] board_bcm963xx: board name: 96368M-1341N
  51. [ 0.000000] Determined physical RAM map:
  52. [ 0.000000] memory: 04000000 @ 00000000 (usable)
  53. [ 0.000000] Initrd not found or empty - disabling initrd
  54. [ 0.000000] PERCPU: Embedded 7 pages/cpu @81083000 s4832 r8192 d15648 u32768
  55. [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
  56. [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
  57. [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  58. [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  59. [ 0.000000] Memory: 61324k/65536k available (2529k kernel code, 4212k reserved, 561k data, 144k init, 0k highmem)
  60. [ 0.000000] Hierarchical RCU implementation.
  61. [ 0.000000] NR_IRQS:128
  62. [ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
  63. [ 0.032000] pid_max: default: 32768 minimum: 301
  64. [ 0.036000] Mount-cache hash table entries: 512
  65. [ 0.040000] SMP: Booting CPU1...
  66. [ 0.044000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
  67. [ 0.080000] SMP: CPU1 is running
  68. [ 0.080000] Brought up 2 CPUs
  69. [ 0.092000] NET: Registered protocol family 16
  70. [ 0.104000] registering PCI controller with io_map_base unset
  71. [ 0.120000] bio: create slab <bio-0> at 0
  72. [ 0.128000] PCI host bridge to bus 0000:00
  73. [ 0.132000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
  74. [ 0.136000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
  75. [ 0.152000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
  76. [ 0.156000] Switching to clocksource MIPS
  77. [ 0.164000] NET: Registered protocol family 2
  78. [ 0.176000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  79. [ 0.180000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
  80. [ 0.188000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
  81. [ 0.196000] TCP: Hash tables configured (established 2048 bind 2048)
  82. [ 0.204000] TCP reno registered
  83. [ 0.204000] UDP hash table entries: 128 (order: 0, 4096 bytes)
  84. [ 0.212000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
  85. [ 0.220000] NET: Registered protocol family 1
  86. [ 0.228000] audit: initializing netlink socket (disabled)
  87. [ 0.232000] type=2000 audit(0.228:1): initialized
  88. [ 0.240000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  89. [ 0.244000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  90. [ 0.256000] msgmni has been set to 119
  91. [ 0.260000] io scheduler noop registered
  92. [ 0.264000] io scheduler deadline registered (default)
  93. ꊊ[ 0.276000] console [ttyS0] enabled, bootconsole disabled 10) is a bcm63xx_uart
  94. [ 0.276000] console [ttyS0] enabled, bootconsole disabled
  95. [ 0.292000] bcm63xx-rng bcm63xx-rng: registered RNG driver
  96. [ 0.300000] physmap platform flash device: 08000000 at 18000000
  97. [ 0.304000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
  98. [ 0.316000] Amd/Fujitsu Extended Query Table at 0x0040
  99. [ 0.320000] Amd/Fujitsu Extended Query version 1.1.
  100. [ 0.328000] number of CFI chips: 1
  101. [ 0.332000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1341N
  102. [ 0.340000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
  103. [ 0.344000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 11ff00
  104. [ 0.352000] bcm63xxpart: Partition 2 is rootfs offset 130000 and length 6c0000
  105. [ 0.360000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
  106. [ 0.368000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
  107. [ 0.376000] bcm63xxpart: Spare partition is offset 4b0004 and length 33fffc
  108. [ 0.384000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
  109. [ 0.388000] Creating 5 MTD partitions on "physmap-flash.0":
  110. [ 0.396000] 0x000000000000-0x000000010000 : "CFE"
  111. [ 0.404000] 0x000000010100-0x000000130000 : "kernel"
  112. [ 0.408000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- y
  113. [ 0.424000] 0x000000130000-0x0000007f0000 : "rootfs"
  114. [ 0.432000] mtd: partition "rootfs" set to be root filesystem
  115. [ 0.440000] mtd: partition "rootfs_data" created automatically, ofs=4B0000, len=340000
  116. [ 0.448000] 0x0000004b0000-0x0000007f0000 : "rootfs_data"
  117. [ 0.456000] 0x0000007f0000-0x000000800000 : "nvram"
  118. [ 0.464000] 0x000000010000-0x0000007f0000 : "linux"
  119. [ 0.472000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542) v0.1.2
  120. [ 0.516000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
  121. [ 0.528000] TCP cubic registered
  122. [ 0.532000] NET: Registered protocol family 17
  123. [ 0.536000] 8021q: 802.1Q VLAN Support v1.8
  124. [ 0.548000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  125. [ 0.556000] Freeing unused kernel memory: 144k freed
  126. procd: Console is alive
  127. procd: - watchdog -
  128. procd: - preinit -
  129. ifconfig: SIOCGIFFLAGS: No such device
  130. Press the [f] key and hit [enter] to enter failsafe mode
  131. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  132. [ 3.692000] usbcore: registered new interface driver usbfs
  133. [ 3.696000] usbcore: registered new interface driver hub
  134. [ 3.704000] usbcore: registered new device driver usb
  135. [ 3.776000] SCSI subsystem initialized
  136. [ 3.796000] Initializing USB Mass Storage driver...
  137. [ 3.800000] usbcore: registered new interface driver usb-storage
  138. [ 3.808000] USB Mass Storage support registered.
  139. kmod: ran 1 iterations
  140. [ 5.968000] JFFS2 notice: (211) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, .
  141. mount_root: jffs2 is ready
  142. [ 6.036000] JFFS2 notice: (208) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, .
  143. ifconfig: SIOCGIFFLAGS: No such device
  144. procd: - early -
  145. procd: - watchdog -
  146. procd: - ubus -
  147. procd: - init -
  148. Please press Enter to activate this console.
  149. [ 8.168000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093
  150. [ 8.176000] Backport generated by backports.git backports-20130802-0-gdb67a3f
  151. [ 8.192000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
  152. [ 8.224000] xt_time: kernel timezone is -0000
  153. [ 8.264000] cfg80211: Calling CRDA to update world regulatory domain
  154. [ 8.276000] cfg80211: World regulatory domain updated:
  155. [ 8.280000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  156. [ 8.292000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  157. [ 8.300000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  158. [ 8.300000] ip_tables: (C) 2000-2006 Netfilter Core Team
  159. [ 8.312000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  160. [ 8.320000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
  161. [ 8.328000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
  162. [ 8.336000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
  163. [ 10.032000] cfg80211: Calling CRDA for country: AW
  164. [ 10.036000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc0400000, irq=21
  165. [ 10.044000] cfg80211: Regulatory domain changed to country: AW
  166. [ 10.052000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  167. [ 10.060000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
  168. [ 10.068000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
  169. [ 10.076000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
  170. [ 10.084000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
  171. [ 14.236000] device eth0.1 entered promiscuous mode
  172. [ 14.240000] device eth0 entered promiscuous mode
  173. [ 14.256000] br-lan: port 1(eth0.1) entered forwarding state
  174. [ 14.264000] br-lan: port 1(eth0.1) entered forwarding state
  175. [ 16.268000] br-lan: port 1(eth0.1) entered forwarding state
  176. procd: - init complete -
  177.  
  178.  
  179.  
  180. BusyBox v1.19.4 (2013-11-26 20:58:33 CET) built-in shell (ash)
  181. Enter 'help' for a list of built-in commands.
  182.  
  183. _______ ________ __
  184. | |.-----.-----.-----.| | | |.----.| |_
  185. | - || _ | -__| || | | || _|| _|
  186. |_______|| __|_____|__|__||________||__| |____|
  187. |__| W I R E L E S S F R E E D O M
  188. ----------------�jjjjjjjjjjjjjjjjjjjjjjj��(*ԪRQ� BREAKER (Bleeding Edge, r38917)
  189. -----------------------------------------------------
  190. * 1/2 oz Galliano Pour all ingredients into
  191. * 4 oz cold Coffee an irish coffee mug filled
  192. * 1 1/2 oz Dark Rum with crushed ice. Stir.
  193. * 2 tsp. Creme de Cacao
  194. -----------------------------------------------------
  195. root@OpenWrt:/# cat /proc/cpuinfo
  196. system type : bcm63xx/96368M-1341N (0x6368/0x00B2)
  197. processor : 0
  198. cpu model : Broadcom BMIPS4350 V3.1
  199. BogoMIPS : 397.82
  200. wait instruction : yes
  201. microsecond timers : yes
  202. tlb_entries : 32
  203. extra interrupt vector : yes
  204. hardware watchpoint : no
  205. ASEs implemented :
  206. shadow register sets : 1
  207. kscratch registers : 0
  208. core : 0
  209. VCED exceptions : not available
  210. VCEI exceptions : not available
  211.  
  212. processor : 1
  213. cpu model : Broadcom BMIPS4350 V3.1
  214. BogoMIPS : 397.82
  215. wait instruction : yes
  216. microsecond timers : yes
  217. tlb_entries : 32
  218. extra interrupt vector : yes
  219. hardware watchpoint : no
  220. ASEs implemented :
  221. shadow register sets : 1
  222. kscratch registers : 0
  223. core : 0
  224. VCED exceptions : not available
  225. VCEI exceptions : not available
  226.  
  227. root@OpenWrt:/# ls -R /etc
  228. /etc:
  229. TZ hotplug.json rc.common
  230. banner init.d rc.d
  231. config inittab rc.local
  232. crontabs modules-boot.d resolv.conf
  233. diag.sh modules.d screenrc
  234. dnsmasq.conf mtab services
  235. dropbear openwrt_release shadow
  236. ethers openwrt_version shells
  237. firewall.user opkg.conf sysctl.conf
  238. fstab passwd sysupgrade.conf
  239. group preinit uci-defaults
  240. hosts profile udev
  241. hotplug-preinit.json protocols
  242. hotplug.d rc.button
  243.  
  244. /etc/config:
  245. dhcp firewall luci system uhttpd
  246. dropbear fstab network ucitrack wireless
  247.  
  248. /etc/crontabs:
  249. =================================================================================================
  250. /etc/dropbear:
  251. dropbear_dss_host_key opoparar_dssososkekey
  252. dropbear_rsa_host_key opopbearsasaososkekey
  253. =================================================================================================
  254. /etc/hotplug.d:
  255. block firmware iface net
  256.  
  257. /etc/hotplug.d/block:
  258. 10-mount
  259.  
  260. /etc/hotplug.d/firmware:
  261. 10-rt2x00-eeprom
  262.  
  263. /etc/hotplug.d/iface:
  264. 00-netstate 20-firewall
  265.  
  266. /etc/hotplug.d/net:
  267. 00-sysctl
  268.  
  269. /etc/init.d:
  270. boot firewall luci_fixtime telnet
  271. cron fstab network uhttpd
  272. dnsmasq led rngd umount
  273. done log sysctl
  274. dropbear luci_dhcp_migrate sysntpd
  275.  
  276. /etc/modules-boot.d:
  277. 02-crypto-hash 20-usb-core 30-fs-ext4 40-scsi-core usb-storage
  278.  
  279. /etc/modules.d:
  280. 02-crypto-hash 25-nls-iso8859-1 ipt-conntrack
  281. 09-crypto-aes 25-nls-iso8859-15 ipt-core
  282. 09-crypto-arc4 30-fs-ext4 ipt-nat
  283. 09-crypto-pcompress 30-fs-vfat lib-crc16
  284. 20-usb-core 40-fs-msdos usb-storage
  285. 25-nls-cp437 40-scsi-core
  286. 25-nls-cp850 ath9k
  287.  
  288. /etc/rc.button:
  289. failsafe reset rfkill wps
  290.  
  291. /etc/rc.d:
  292. K50dropbear S11sysctl S50uhttpd
  293. K89log S12log S59luci_dhcp_migrate
  294. K90network S19firewall S60dnsmasq
  295. K95luci_fixtime S20network S95done
  296. K98boot S40fstab S96led
  297. K99umount S50cron S98rngd
  298. S05luci_fixtime S50dropbear S98sysntpd
  299. S10boot S50telnet
  300.  
  301. /etc/uci-defaults:
  302.  
  303. /etc/udev:
  304. rules.d udev.conf
  305.  
  306. /etc/udev/rules.d:
  307. root@OpenWrt:/#
RAW Paste Data