Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- root@OpenWrt:~# dmesg
- [ 0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42625) ) #3 Wed Oct 1 14:00:51 CEST 2014
- [ 0.000000] MyLoader: sysp=74f2f0f7, boardp=d6fff4ff, parts=40b0b0e0
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
- [ 0.000000] SoC: Atheros AR7240 rev 2
- [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 02000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x01ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
- [ 0.000000] On node 0 totalpages: 8192
- [ 0.000000] free_area_init_node: node 0, pgdat 80334b60, node_mem_map 81000000
- [ 0.000000] Normal zone: 64 pages used for memmap
- [ 0.000000] Normal zone: 0 pages reserved
- [ 0.000000] Normal zone: 8192 pages, LIFO batch:0
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
- [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
- [ 0.000000] pcpu-alloc: [0] 0
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
- [ 0.000000] Kernel command line: board=WNR612V2 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd
- [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
- [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Writing ErrCtl register=00000000
- [ 0.000000] Readback ErrCtl register=00000000
- [ 0.000000] Memory: 28588k/32768k available (2369k kernel code, 4180k reserved, 621k data, 272k init, 0k highmem)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:51
- [ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
- [ 0.080000] pid_max: default: 32768 minimum: 301
- [ 0.080000] Mount-cache hash table entries: 512
- [ 0.090000] NET: Registered protocol family 16
- [ 0.100000] MIPS: machine is NETGEAR WNR612 V2
- [ 0.100000] ar71xx: using random MAC address for eth0
- [ 0.300000] ar71xx: using random MAC address for eth1
- [ 0.500000] registering PCI controller with io_map_base unset
- [ 0.510000] bio: create slab <bio-0> at 0
- [ 0.520000] PCI host bridge to bus 0000:00
- [ 0.520000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
- [ 0.530000] pci_bus 0000:00: root bus resource [io 0x0000]
- [ 0.530000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 0.540000] pci 0000:00:00.0: [168c:ff1c] type 00 class 0x020000
- [ 0.540000] pci 0000:00:00.0: invalid calibration data
- [ 0.540000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0000ffff 64bit]
- [ 0.540000] pci 0000:00:00.0: supports D1
- [ 0.540000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
- [ 0.540000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
- [ 0.540000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
- [ 0.550000] pci 0000:00:00.0: using irq 40 for pin 1
- [ 0.550000] Switching to clocksource MIPS
- [ 0.560000] NET: Registered protocol family 2
- [ 0.560000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.570000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
- [ 0.580000] TCP: Hash tables configured (established 512 bind 512)
- [ 0.580000] TCP: reno registered
- [ 0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.600000] NET: Registered protocol family 1
- [ 0.600000] PCI: CLS 0 bytes, default 32
- [ 0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.630000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.640000] msgmni has been set to 55
- [ 0.650000] io scheduler noop registered
- [ 0.650000] io scheduler deadline registered (default)
- [ 0.660000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.690000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
- [ 0.700000] console [ttyS0] enabled, bootconsole disabled
- [ 0.710000] ath79-spi ath79-spi: master is unqueued, this is deprecated
- [ 0.720000] m25p80 spi0.0: found mx25l3205d, expected m25p80
- [ 0.720000] m25p80 spi0.0: mx25l3205d (4096 Kbytes)
- [ 0.730000] 4 cmdlinepart partitions found on MTD device spi0.0
- [ 0.740000] Creating 4 MTD partitions on "spi0.0":
- [ 0.740000] 0x000000000000-0x000000040000 : "u-boot"
- [ 0.750000] 0x000000040000-0x000000050000 : "u-boot-env"
- [ 0.750000] 0x000000050000-0x0000003f0000 : "firmware"
- [ 0.760000] 2 netgear-fw partitions found on MTD device firmware
- [ 0.770000] 0x000000050000-0x000000162440 : "kernel"
- [ 0.770000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
- [ 0.790000] 0x000000162440-0x0000003f0000 : "rootfs"
- [ 0.790000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
- [ 0.810000] mtd: device 4 (rootfs) set to be root filesystem
- [ 0.810000] 1 squashfs-split partitions found on MTD device rootfs
- [ 0.820000] 0x000000390000-0x0000003f0000 : "rootfs_data"
- [ 0.830000] 0x0000003f0000-0x000000400000 : "art"
- [ 0.940000] libphy: ag71xx_mdio: probed
- [ 1.520000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Generic PHY]
- [ 1.530000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
- [ 2.100000] ag71xx-mdio.0: Found an AR7240/AR9330 built-in switch
- [ 3.130000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
- [ 3.130000] TCP: cubic registered
- [ 3.140000] NET: Registered protocol family 17
- [ 3.140000] Bridge firewalling registered
- [ 3.150000] 8021q: 802.1Q VLAN Support v1.8
- [ 3.160000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
- [ 3.170000] Freeing unused kernel memory: 272K (8034c000 - 80390000)
- [ 6.060000] usbcore: registered new interface driver usbfs
- [ 6.070000] usbcore: registered new interface driver hub
- [ 6.070000] usbcore: registered new device driver usb
- [ 6.080000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 6.090000] ehci-platform: EHCI generic platform driver
- [ 6.100000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 10.890000] jffs2: notice: (318) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 16 of xref (0 dead, 2 orphan) found.
- [ 12.510000] NET: Registered protocol family 10
- [ 12.530000] nf_conntrack version 0.5.0 (450 buckets, 1800 max)
- [ 12.540000] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 12.560000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
- [ 12.560000] Backport generated by backports.git backports-20140320-37-g5c33da0
- [ 12.580000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 12.640000] xt_time: kernel timezone is -0000
- [ 12.670000] cfg80211: Calling CRDA to update world regulatory domain
- [ 12.670000] cfg80211: World regulatory domain updated:
- [ 12.680000] cfg80211: DFS Master region: unset
- [ 12.680000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
- [ 12.690000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- [ 12.700000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- [ 12.710000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
- [ 12.720000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
- [ 12.720000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
- [ 12.730000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
- [ 12.740000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
- [ 12.750000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
- [ 12.820000] PPP generic driver version 2.4.2
- [ 12.840000] NET: Registered protocol family 24
- [ 24.400000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
- [ 24.400000] device eth1 entered promiscuous mode
- [ 24.410000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
- [ 24.430000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- [ 69.000000] eth1: link up (1000Mbps/Full duplex)
- [ 69.000000] br-lan: port 1(eth1) entered forwarding state
- [ 69.010000] br-lan: port 1(eth1) entered forwarding state
- [ 69.010000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
- [ 69.020000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
- [ 71.010000] br-lan: port 1(eth1) entered forwarding state
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement