GXBB:BL1:08dafd:0a8993;FEAT:EDFC318C;POC:3;RCY:0;EMMC:0;READ:0;CHK:F3;SD:0;READ:0;CHK:0;
TE: 250045
no sdio debug board detected

BL2 Built : 13:55:05, Jan 28 2016.
gxb g3625dd5 - xiaobo.gu@droid05

Board ID = 0
set vcck to 1100 mv
set vddee to 1000 mv
CPU clk: 1536MHz
DDR channel setting: DDR0 Rank0+1 diff
DDR0: 1024MB(auto) @ 912MHz(2T)-13
DDR1: 1024MB(auto) @ 912MHz(2T)-13
DataBus test pass!
AddrBus test pass!
Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from SD, src: 0x00010200, des: 0x01000000, size: 0x0000a9b0
Sending bl30...........................................OK.
Run bl30...
Load bl301 from SD, src: 0x0001c200, des: 0x01000000, size: 0x00001c30
Wait bl30...Done
Sending bl301........OK.
Run bl301...
rc: 0x00020200, des: 0x10100000, size: 0x00012130


--- UART initialized after reboot ---
[Reset cause: unknown]
[Image: unknown, amlogic_v1.1.3054-53e549c 2016-03-31 20:40:25 xing.xu@droid05]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: ef be ad de d f0 ad ba ef be aLoad bl33 from SD, src: 0x00034200, des: 0x01000000, size: 0x0009fc80
d de not ES chip
efuse init ops = 13
efuse init hdcp = c, cf9=7
[0.380734 Inits done]
secure task start!
high task start!
low task start!
NOTICE:  BL3-1: v1.0(debug):4c66217
NOTICE:  BL3-1: Built : 17:13:36, Jan 28 2016
INFO:    BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address = 0x1000000
INFO:    BL3-1: Next image spsr = 0x3c9


U-Boot 2015.01-ge699316 (Apr 21 2016 - 19:57:11)

DRAM:  2 GiB
Relocation Offset is: 76ed3000
register usb cfg[0][1] = 0000000077f62040
register usb cfg[0][2] = 0000000077f62060
register usb cfg[2][0] = 0000000077f62080
vpu detect type: 5
vpu clk_level = 7
set vpu clk: 666667000Hz, readback: 666660000Hz(0x300)
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=8, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC:   aml_priv->desc_buf = 0x0000000073ec3770
aml_priv->desc_buf = 0x0000000073ec5900
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
      Amlogic multi-dtb tool
      Cannot find legal dtb!
start dts,buffer=0000000073ec7ff0,dt_addr=0000000073ec7ff0
get_partition_from_dts: FDT_ERR_BADMAGIC
!!!!get dts FAILED
mmc get partition error!
get partition info failed !!
Using default environment

In:    serial
Out:   serial
Err:   serial
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
      Amlogic multi-dtb tool
      Cannot find legal dtb!
[store]Err:do_store_dtb_ops,L230:Fail in fdt check header
board_late_init(): [store dtb read $dtb_mem_addr] fail
load dtb to 1000000
[store]To run cmd[emmc dtb_read 1000000 0x40000]
read emmc dtb
      Amlogic multi-dtb tool
      Cannot find legal dtb!
[store]Err:do_store_dtb_ops,L230:Fail in fdt check header
board_late_init(): store dtb read 1000000 fail
ret = 1 .[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 41
OEM: 3432
Name: SD16G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 14.5 GiB
Bus Width: 4-bit
[MSG]ini sz 0x24bB
[fat]Filesize is 0x24bB[0M]
[fat]0x:leftSz 24b < BPS 2000, gotSz 24b

=========sdc_burn_paras=====>>>
[common]
erase_bootloader = 1
erase_flash      = 1
reboot           = 0x1
key_overwrite    = 0x0

[burn_ex]
package          = recovery.img
media            =

[burn_parts]
burn_num         = 0

<<<<=====sdc_burn_paras======

[fat]Filesize is 0x2c5baa94B[709M]
[fat]0x:leftSz c40 < BPS 2000, gotSz 6c40
[MSG]image version [0x00000002]
[fat]Seek 0x12b7c10 from 0x6c40
[MSG]itemSizeNotAligned 0x3f0
[MSG]align 4 mmc read...        [fat]0x:leftSz 1cef < BPS 2000, gotSz 80df
[MSG]Down(mem) part(dtb) sz(0x80df) fmt(normal)
[MSG]Burn Start...
[MSG]load dt.img to 0x0000000001000000, sz=0x80df
[MSG]Burn complete
Err imgread(L433):Logo header err.
Cannot find dev.
amlmmc cmd <NULL> failed

store - STORE sub-system

Usage:
store store init flag
store read name addr off|partition size
    read 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
    write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
        write uboot to the boot device
store erase boot/data:
        erase the area which is uboot or data
store erase dtb
store erase key
store rom_protect on/off
store scrub off|partition size
        scrub the area from offset and size
store dtb iread/read/write addr <size>
        read/write dtb, size is optional
store key read/write addr <size>
        read/write key, size is optional

cmd store failed
Err imgread(L246):Fail to read 0x100000B from part[logo] at offset 0
[MSG]Use upgrade res in pkg
[WRN]Can't find item [logo, aml_sdc_burn]
[MSG]logo for sdc UPGRADE[PARTITION]
[MSG]itemSizeNotAligned 0x1cc4
[MSG]align 4 mmc read...        [fat]0x:leftSz e4c < BPS 2000, gotSz 738b10
[MSG]echo video prepare for upgrade
hpd_state=0
[CANVAS]addr=0x3f800000 width=5760, height=2160

Not find '576cvbs' mapped VIC
[MSG]dw,dh[1920, 1080]
[MSG]w,h[4,14]
[MSG]Exit before re-init
command:        store  exit
      Amlogic multi-dtb tool
      Single dtb detected
start dts,buffer=0000000001000000,dt_addr=0000000001000000
parts: 11
00:      logo   0000000002000000 1
01:  recovery   0000000002000000 1
02:       rsv   0000000000800000 1
03:       tee   0000000000800000 1
04:     crypt   0000000002000000 1
05:      misc   0000000002000000 1
06: instaboot   0000000020000000 1
07:      boot   0000000002000000 1
08:    system   0000000080000000 1
09:     cache   0000000020000000 2
10:      data   ffffffffffffffff 4
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
        name                        offset              size              flag
===================================================================================
   0: bootloader                         0            400000                  0
   1: reserved                     2400000           4000000                  0
   2: cache                        6c00000          20000000                  2
   3: env                         27400000            800000                  0
   4: logo                        28400000           2000000                  1
   5: recovery                    2ac00000           2000000                  1
   6: rsv                         2d400000            800000                  1
   7: tee                         2e400000            800000                  1
   8: crypt                       2f400000           2000000                  1
   9: misc                        31c00000           2000000                  1
  10: instaboot                   34400000          20000000                  1
  11: boot                        54c00000           2000000                  1
  12: system                      57400000          80000000                  1
  13: data                        d7c00000          f6500000                  4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition ERROR!
mmc write lba=0x12000, blocks=0x2
mmc write lba=0x12002, blocks=0x2
mmc_write_partition_tbl: mmc write partition OK!
eMMC/TSD partition table have been checked OK!
switch to partitions #0, OK
mmc1(part 0) is current device
Device: SDIO Port C
Manufacturer ID: 65
OEM: 646f
Name: M MOR
Tran Speed: 25000000
Rd Block Len: 512
MMC version 4.41
High Capacity: Yes
Capacity: 7.2 GiB
Bus Width: 8-bit
[store]amlmmc erase 1emmckey_is_protected : protect
 start = 0,end = 57343


Caution! Your devices Erase group is 0x400
The erase range would be change to 0x36000~0xe707ff

start = 221184,end = 15140862
start erase dtb......
start = 81920,end = 82943
dev # 1,  , several blocks erased OK
[store]To run cmd[emmc dtb_write 0x0000000001000000 0x40000]
write emmc dtb
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
        name                        offset              size              flag
===================================================================================
   0: bootloader                         0            400000                  0
   1: reserved                     2400000           4000000                  0
   2: cache                        6c00000          20000000                  2
   3: env                         27400000            800000                  0
   4: logo                        28400000           2000000                  1
   5: recovery                    2ac00000           2000000                  1
   6: rsv                         2d400000            800000                  1
   7: tee                         2e400000            800000                  1
   8: crypt                       2f400000           2000000                  1
   9: misc                        31c00000           2000000                  1
  10: instaboot                   34400000          20000000                  1
  11: boot                        54c00000           2000000                  1
  12: system                      57400000          80000000                  1
  13: data                        d7c00000          f6500000                  4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition ERROR!
mmc write lba=0x12000, blocks=0x2
mmc write lba=0x12002, blocks=0x2
mmc_write_partition_tbl: mmc write partition OK!
 partition table success
      Amlogic multi-dtb tool
      Single dtb detected
[burn_parts]
burn_num         = 4
burn_part0       = boot
burn_part1       = logo
burn_part2       = recovery
burn_part3       = system


[MSG]=====>To burn part [boot]
[MSG]itemSizeNotAligned 0x1524
[MSG]flash LOGIC partCap 0x2000000B
[MSG]Down(store) part(boot) sz(0x8ef800) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 143
[MSG]itemSizeNotAligned 0x1524
[fat]0x:leftSz 2dc < BPS 2000, gotSz e2dc
[MSG]Burn Start...
[MSG]Burn complete
[MSG]Verify Start...
[MSG]To verify part boot in fmt normal
[MSG]Verify End
ERR(../drivers/usb/gadget/v2_burning/v2_common/optimus_download.c)L938:failed:Verify Failed with sha1sum, origin sum "ec8cff92d40f242f6372e0aefffad81e77ee54ce" != gen sum "1fdfc90abf10ba22d09d13b66d96631a11190af0"
ERR(../drivers/usb/gadget/v2_burning/v2_sdc_burn/optimus_sdc_burn.c)L112:Fail when verify
Fail in verify part(boot)
ERR(../drivers/usb/gadget/v2_burning/v2_sdc_burn/optimus_sdc_burn.c)L260:Fail in burn part boot
ERR(../drivers/usb/gadget/v2_burning/v2_sdc_burn/optimus_sdc_burn.c)L665:Fail when burn partitions
[MSG]to close image
[MSG]=====Burn Failed!!!!!
[MSG]PLS long-press power key to shut down