milomak

smartctl mythtv sdc

Oct 8th, 2014
233
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-4-amd64] (local build)
  2. Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
  3.  
  4. === START OF INFORMATION SECTION ===
  5. Device Model: WDC WD30EZRX-00DC0B0
  6. Serial Number: WD-WMC1T0697215
  7. LU WWN Device Id: 5 0014ee 6582907e6
  8. Firmware Version: 80.00A80
  9. User Capacity: 3,000,592,982,016 bytes [3.00 TB]
  10. Sector Sizes: 512 bytes logical, 4096 bytes physical
  11. Device is: Not in smartctl database [for details use: -P showall]
  12. ATA Version is: 9
  13. ATA Standard is: Exact ATA specification draft version not indicated
  14. Local Time is: Wed Oct 8 20:24:48 2014 SAST
  15. SMART support is: Available - device has SMART capability.
  16. SMART support is: Enabled
  17.  
  18. === START OF READ SMART DATA SECTION ===
  19. SMART overall-health self-assessment test result: PASSED
  20.  
  21. General SMART Values:
  22. Offline data collection status: (0x82) Offline data collection activity
  23. was completed without error.
  24. Auto Offline Data Collection: Enabled.
  25. Self-test execution status: ( 0) The previous self-test routine completed
  26. without error or no self-test has ever
  27. been run.
  28. Total time to complete Offline
  29. data collection: (41520) seconds.
  30. Offline data collection
  31. capabilities: (0x7b) SMART execute Offline immediate.
  32. Auto Offline data collection on/off support.
  33. Suspend Offline collection upon new
  34. command.
  35. Offline surface scan supported.
  36. Self-test supported.
  37. Conveyance Self-test supported.
  38. Selective Self-test supported.
  39. SMART capabilities: (0x0003) Saves SMART data before entering
  40. power-saving mode.
  41. Supports SMART auto save timer.
  42. Error logging capability: (0x01) Error logging supported.
  43. General Purpose Logging supported.
  44. Short self-test routine
  45. recommended polling time: ( 2) minutes.
  46. Extended self-test routine
  47. recommended polling time: ( 255) minutes.
  48. Conveyance self-test routine
  49. recommended polling time: ( 5) minutes.
  50. SCT capabilities: (0x70b5) SCT Status supported.
  51. SCT Feature Control supported.
  52. SCT Data Table supported.
  53.  
  54. SMART Attributes Data Structure revision number: 16
  55. Vendor Specific SMART Attributes with Thresholds:
  56. ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
  57. 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
  58. 3 Spin_Up_Time 0x0027 195 177 021 Pre-fail Always - 5216
  59. 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 168
  60. 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
  61. 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
  62. 9 Power_On_Hours 0x0032 082 082 000 Old_age Always - 13224
  63. 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
  64. 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
  65. 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 167
  66. 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 152
  67. 193 Load_Cycle_Count 0x0032 157 157 000 Old_age Always - 130217
  68. 194 Temperature_Celsius 0x0022 110 102 000 Old_age Always - 40
  69. 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
  70. 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
  71. 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
  72. 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
  73. 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
  74.  
  75. SMART Error Log Version: 1
  76. Warning: ATA error count 27630 inconsistent with error log pointer 3
  77.  
  78. ATA Error Count: 27630 (device log contains only the most recent five errors)
  79. CR = Command Register [HEX]
  80. FR = Features Register [HEX]
  81. SC = Sector Count Register [HEX]
  82. SN = Sector Number Register [HEX]
  83. CL = Cylinder Low Register [HEX]
  84. CH = Cylinder High Register [HEX]
  85. DH = Device/Head Register [HEX]
  86. DC = Device Command Register [HEX]
  87. ER = Error register [HEX]
  88. ST = Status register [HEX]
  89. Powered_Up_Time is measured from power on, and printed as
  90. DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
  91. SS=sec, and sss=millisec. It "wraps" after 49.710 days.
  92.  
  93. Error 27630 occurred at disk power-on lifetime: 13175 hours (548 days + 23 hours)
  94. When the command that caused the error occurred, the device was active or idle.
  95.  
  96. After command completion occurred, registers were:
  97. ER ST SC SN CL CH DH
  98. -- -- -- -- -- -- --
  99. 04 61 46 00 00 00 a0 Device Fault; Error: ABRT
  100.  
  101. Commands leading to the command that caused the error were:
  102. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  103. -- -- -- -- -- -- -- -- ---------------- --------------------
  104. ef 03 46 00 00 00 a0 00 21:38:30.991 SET FEATURES [Set transfer mode]
  105. ec 00 00 00 00 00 a0 00 21:38:30.991 IDENTIFY DEVICE
  106. ec 00 00 00 00 00 a0 00 21:38:30.990 IDENTIFY DEVICE
  107. ef 03 46 00 00 00 a0 00 21:38:30.990 SET FEATURES [Set transfer mode]
  108.  
  109. Error 27629 occurred at disk power-on lifetime: 13175 hours (548 days + 23 hours)
  110. When the command that caused the error occurred, the device was active or idle.
  111.  
  112. After command completion occurred, registers were:
  113. ER ST SC SN CL CH DH
  114. -- -- -- -- -- -- --
  115. 04 61 46 00 00 00 a0 Device Fault; Error: ABRT
  116.  
  117. Commands leading to the command that caused the error were:
  118. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  119. -- -- -- -- -- -- -- -- ---------------- --------------------
  120. ef 03 46 00 00 00 a0 00 21:38:30.990 SET FEATURES [Set transfer mode]
  121. ec 00 00 00 00 00 a0 00 21:38:30.988 IDENTIFY DEVICE
  122. ec 00 00 00 00 00 a0 00 21:38:30.987 IDENTIFY DEVICE
  123. ef 03 46 00 00 00 a0 00 21:38:30.987 SET FEATURES [Set transfer mode]
  124.  
  125. Error 27628 occurred at disk power-on lifetime: 13175 hours (548 days + 23 hours)
  126. When the command that caused the error occurred, the device was active or idle.
  127.  
  128. After command completion occurred, registers were:
  129. ER ST SC SN CL CH DH
  130. -- -- -- -- -- -- --
  131. 04 61 46 00 00 00 a0 Device Fault; Error: ABRT
  132.  
  133. Commands leading to the command that caused the error were:
  134. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  135. -- -- -- -- -- -- -- -- ---------------- --------------------
  136. ef 03 46 00 00 00 a0 00 21:38:30.987 SET FEATURES [Set transfer mode]
  137. ec 00 00 00 00 00 a0 00 21:38:30.987 IDENTIFY DEVICE
  138. ec 00 00 00 00 00 a0 00 21:38:28.628 IDENTIFY DEVICE
  139. ef 03 46 00 00 00 a0 00 21:38:28.627 SET FEATURES [Set transfer mode]
  140.  
  141. Error 27627 occurred at disk power-on lifetime: 13175 hours (548 days + 23 hours)
  142. When the command that caused the error occurred, the device was active or idle.
  143.  
  144. After command completion occurred, registers were:
  145. ER ST SC SN CL CH DH
  146. -- -- -- -- -- -- --
  147. 04 61 46 00 00 00 a0 Device Fault; Error: ABRT
  148.  
  149. Commands leading to the command that caused the error were:
  150. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  151. -- -- -- -- -- -- -- -- ---------------- --------------------
  152. ef 03 46 00 00 00 a0 00 21:38:28.627 SET FEATURES [Set transfer mode]
  153. ec 00 00 00 00 00 a0 00 21:38:28.627 IDENTIFY DEVICE
  154. ca 00 08 00 10 00 e0 00 21:38:28.626 WRITE DMA
  155. ec 00 00 00 00 00 a0 00 21:38:28.626 IDENTIFY DEVICE
  156. ef 03 46 00 00 00 a0 00 21:38:28.626 SET FEATURES [Set transfer mode]
  157.  
  158. Error 27626 occurred at disk power-on lifetime: 13175 hours (548 days + 23 hours)
  159. When the command that caused the error occurred, the device was active or idle.
  160.  
  161. After command completion occurred, registers were:
  162. ER ST SC SN CL CH DH
  163. -- -- -- -- -- -- --
  164. 04 61 08 00 10 00 e0 Device Fault; Error: ABRT at LBA = 0x00001000 = 4096
  165.  
  166. Commands leading to the command that caused the error were:
  167. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  168. -- -- -- -- -- -- -- -- ---------------- --------------------
  169. ca 00 08 00 10 00 e0 00 21:38:28.626 WRITE DMA
  170. ec 00 00 00 00 00 a0 00 21:38:28.626 IDENTIFY DEVICE
  171. ef 03 46 00 00 00 a0 00 21:38:28.626 SET FEATURES [Set transfer mode]
  172. ec 00 00 00 00 00 a0 00 21:38:28.626 IDENTIFY DEVICE
  173. ca 00 08 00 10 00 e0 00 21:38:28.625 WRITE DMA
  174.  
  175. SMART Self-test log structure revision number 1
  176. No self-tests have been logged. [To run self-tests, use: smartctl -t]
  177.  
  178.  
  179. SMART Selective self-test log data structure revision number 1
  180. SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
  181. 1 0 0 Not_testing
  182. 2 0 0 Not_testing
  183. 3 0 0 Not_testing
  184. 4 0 0 Not_testing
  185. 5 0 0 Not_testing
  186. Selective self-test flags (0x0):
  187. After scanning selected spans, do NOT read-scan remainder of disk.
  188. If Selective self-test is pending on power-up, resume after 0 minute delay.
RAW Paste Data