API tools faq
paste
Advertisement
Guest User

Log serial port NAS Iconbit I-STOR IS608

a guest
Jan 5th, 2018
431
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 16.23 KB | None | 0 0
raw download clone embed print report
  1. U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12)
  2. Boot device: SATA
  3. Attempting to set PLLA to 800 MHz ...
  4. plla_ctrl0 : 0000030a
  5. plla_ctrl1 : 00400000
  6. plla_ctrl2 : 007f0068
  7. plla_ctrl3 : 00000193
  8.  
  9. PLLA Set
  10. Bus 0: OK
  11. Device 0:
  12. reading bootargs.bin
  13. reading u-boot.img
  14. reading u-boot.img
  15.  
  16.  
  17. U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS
  18.  
  19. DRAM: 128 MiB
  20. IDE: Bus 0: OK
  21. Device 0: Model: ST380815AS Firm: 3.AAC Ser#: 6QZ0M5Y2
  22. Type: Hard Disk
  23. Supports 48-bit addressing
  24. Capacity: 76318.0 MB = 74.5 GB (156299375 x 512)
  25. NAND: 256 MiB
  26. reading u-boot.env
  27. In: serial
  28. Out: serial
  29. Err: serial
  30. Net: mii0
  31. ## Error: "safeboot" not defined
  32. Hit any key to stop autoboot: 0
  33. 4488520 bytes read in 709 ms (6 MiB/s)
  34. 7033 bytes read in 26 ms (263.7 KiB/s)
  35. magic: 0xd00dfeed
  36. totalsize: 0x1b79 (7033)
  37. off_dt_struct: 0x38
  38. off_dt_strings: 0x18d4
  39. off_mem_rsvmap: 0x28
  40. version: 17
  41. last_comp_version: 16
  42. boot_cpuid_phys: 0x0
  43. size_dt_strings: 0x2a5
  44. size_dt_struct: 0x189c
  45. number mem_rsv: 0x0
  46.  
  47. ## Booting kernel from Legacy Image at 60000000 ...
  48. Image Name: Linux-4.1.0-oxnas-tld-1
  49. Image Type: ARM Linux Kernel Image (uncompressed)
  50. Data Size: 4488456 Bytes = 4.3 MiB
  51. Load Address: 60008000
  52. Entry Point: 60008000
  53. Verifying Checksum ... OK
  54. ## Flattened Device Tree blob at 61000000
  55. Booting using the fdt blob at 0x61000000
  56. Loading Kernel Image ... OK
  57. Loading Device Tree to 67e26000, end 67e2ab78 ... OK
  58.  
  59. Starting kernel ...
  60.  
  61. Uncompressing Linux... done, booting the kernel.
  62. [ 0.000000] Booting Linux on physical CPU 0x0
  63. [ 0.000000] Linux version 4.1.0-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #3 SMP PREEMPT Wed Jul 1 05:11:47 PDT 2015
  64. [ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
  65. [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  66. [ 0.000000] Machine model: Pogoplug Pro
  67. [ 0.000000] Memory policy: Data cache writealloc
  68. [ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
  69. [ 0.000000] Start Ox820 platform
  70. [ 0.000000] PERCPU: Embedded 11 pages/cpu @c7edc000 s15456 r8192 d21408 u45056
  71. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
  72. [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/sda2 rootfstype=ext4 ubi.mtd=data,512
  73. [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
  74. [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  75. [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  76. [ 0.000000] Memory: 120984K/131072K available (6235K kernel code, 275K rwdata, 1852K rodata, 200K init, 237K bss, 10088K reserved, 0K cma-reserved)
  77. [ 0.000000] Virtual kernel memory layout:
  78. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  79. [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
  80. [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
  81. [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
  82. [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
  83. [ 0.000000] .text : 0xc0008000 - 0xc07edec8 (8088 kB)
  84. [ 0.000000] .init : 0xc07ee000 - 0xc0820000 ( 200 kB)
  85. [ 0.000000] .data : 0xc0820000 - 0xc0864fa0 ( 276 kB)
  86. [ 0.000000] .bss : 0xc0864fa0 - 0xc08a06a0 ( 238 kB)
  87. [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  88. [ 0.000000] Preemptible hierarchical RCU implementation.
  89. [ 0.000000] NR_IRQS:160
  90. [ 0.000000] clocksource rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
  91. [ 0.000010] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
  92. [ 0.000176] Console: colour dummy device 80x30
  93. [ 0.000209] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440)
  94. [ 0.050032] pid_max: default: 32768 minimum: 301
  95. [ 0.050191] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  96. [ 0.050209] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  97. [ 0.051082] Initializing cgroup subsys net_cls
  98. [ 0.051148] CPU: Testing write buffer coherency: ok
  99. [ 0.051548] Setting up static identity map for 0x60008220 - 0x60008258
  100. [ 0.170145] Brought up 2 CPUs
  101. [ 0.170168] SMP: Total of 2 processors activated (638.97 BogoMIPS).
  102. [ 0.171151] devtmpfs: initialized
  103. [ 0.176826] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  104. [ 0.177062] prandom: seed boundary self test passed
  105. [ 0.181744] prandom: 100 self tests passed
  106. [ 0.181775] pinctrl core: initialized pinctrl subsystem
  107. [ 0.182668] NET: Registered protocol family 16
  108. [ 0.183242] DMA: preallocated 256 KiB pool for atomic coherent allocations
  109. [ 0.210009] cpuidle: using governor ladder
  110. [ 0.240005] cpuidle: using governor menu
  111. [ 0.245104] gpio-oxnas 44000000.gpio: at address c8848000
  112. [ 0.245445] gpio-oxnas 44100000.gpio: at address c884a000
  113. [ 0.246041] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
  114. [ 0.260183] vgaarb: loaded
  115. [ 0.260720] SCSI subsystem initialized
  116. [ 0.261591] usbcore: registered new interface driver usbfs
  117. [ 0.261703] usbcore: registered new interface driver hub
  118. [ 0.261857] usbcore: registered new device driver usb
  119. [ 0.262082] pps_core: LinuxPPS API ver. 1 registered
  120. [ 0.262095] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
  121. [ 0.262146] PTP clock support registered
  122. [ 0.263895] cfg80211: Calling CRDA to update world regulatory domain
  123. [ 0.264422] Switched to clocksource rps_clocksource_timer
  124. [ 0.283983] NET: Registered protocol family 2
  125. [ 0.284974] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  126. [ 0.285020] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
  127. [ 0.285061] TCP: Hash tables configured (established 1024 bind 1024)
  128. [ 0.285163] UDP hash table entries: 256 (order: 1, 8192 bytes)
  129. [ 0.285209] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  130. [ 0.285498] NET: Registered protocol family 1
  131. [ 0.286003] RPC: Registered named UNIX socket transport module.
  132. [ 0.286023] RPC: Registered udp transport module.
  133. [ 0.286036] RPC: Registered tcp transport module.
  134. [ 0.286046] RPC: Registered tcp NFSv4.1 backchannel transport module.
  135. [ 0.287856] futex hash table entries: 512 (order: 2, 16384 bytes)
  136. [ 0.287938] Initialise system trusted keyring
  137. [ 0.302192] zpool: loaded
  138. [ 0.302218] zbud: loaded
  139. [ 0.307663] NFS: Registering the id_resolver key type
  140. [ 0.307729] Key type id_resolver registered
  141. [ 0.307742] Key type id_legacy registered
  142. [ 0.307781] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
  143. [ 0.307804] Installing knfsd (copyright (C) 1996 [email protected]).
  144. [ 0.308751] fuse init (API version 7.23)
  145. [ 0.310571] Key type big_key registered
  146. [ 0.316482] alg: No test for stdrng (krng)
  147. [ 0.366873] Key type asymmetric registered
  148. [ 0.366906] Asymmetric key parser 'x509' registered
  149. [ 0.367047] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
  150. [ 0.367080] io scheduler noop registered
  151. [ 0.367104] io scheduler deadline registered
  152. [ 0.367493] io scheduler cfq registered (default)
  153. [ 0.368202] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  154. [ 0.369710] console [ttyS0] disabled
  155. [ 0.369802] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390625) is a 16550A
  156. [ 0.898398] console [ttyS0] enabled
  157. [ 0.912499] loop: module loaded
  158. [ 0.917557] scsi host0: sata_oxnas
  159. [ 0.921443] ata1: SATA max UDMA/133 irq 7
  160. [ 0.925706] ox820sata: reseting SATA core
  161. [ 0.926620] nand: Could not find valid ONFI parameter page; aborting
  162. [ 0.926663] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
  163. [ 0.926668] nand: Hynix NAND 256MiB 3,3V 8-bit
  164. [ 0.926676] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
  165. [ 0.926694] Scanning device for bad blocks
  166. [ 0.953830] Bad eraseblock 324 at 0x000002880000
  167. [ 0.953879] Bad eraseblock 325 at 0x0000028a0000
  168. [ 1.096760] 2 ofpart partitions found on MTD device 41000000.nand
  169. [ 1.102855] Creating 2 MTD partitions on "41000000.nand":
  170. [ 1.108234] 0x000000000000-0x000000e00000 : "boot"
  171. [ 1.114752] 0x000000e00000-0x000008000000 : "data"
  172. [ 1.122081] stmmaceth 40400000.ethernet: no reset control found
  173. [ 1.127982] stmmac - user ID: 0x12, Synopsys ID: 0x35
  174. [ 1.133038] Ring mode enabled
  175. [ 1.136079] DMA HW capability register supported
  176. [ 1.140602] Enhanced/Alternate descriptors
  177. [ 1.144931] Enabled extended descriptors
  178. [ 1.148915] RX Checksum Offload Engine supported (type 2)
  179. [ 1.154383] TX Checksum insertion supported
  180. [ 1.158625] Wake-Up On Lan supported
  181. [ 1.162280] Enable RX Mitigation via HW Watchdog Timer
  182. [ 1.171328] libphy: stmmac: probed
  183. [ 1.174727] eth0: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active
  184. [ 1.181068] eth0: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03)
  185. [ 1.186885] PPP generic driver version 2.4.2
  186. [ 1.191777] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  187. [ 1.198287] ehci-pci: EHCI PCI platform driver
  188. [ 1.203266] oxnas-ehci 40200100.ehci: EHCI Host Controller
  189. [ 1.208762] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
  190. [ 1.216634] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100
  191. [ 1.240576] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
  192. [ 1.246881] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
  193. [ 1.253675] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  194. [ 1.260884] usb usb1: Product: EHCI Host Controller
  195. [ 1.265735] usb usb1: Manufacturer: Linux 4.1.0-oxnas-tld-1 ehci_hcd
  196. [ 1.272071] usb usb1: SerialNumber: 40200100.ehci
  197. [ 1.277724] hub 1-0:1.0: USB hub found
  198. [ 1.281582] hub 1-0:1.0: 2 ports detected
  199. [ 1.286553] usbcore: registered new interface driver cdc_acm
  200. [ 1.292226] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  201. [ 1.300308] usbcore: registered new interface driver cdc_wdm
  202. [ 1.306140] usbcore: registered new interface driver usb-storage
  203. [ 1.312394] usbcore: registered new interface driver usbserial
  204. [ 1.318287] usbcore: registered new interface driver usbserial_generic
  205. [ 1.324881] usbserial: USB Serial support registered for generic
  206. [ 1.331302] mousedev: PS/2 mouse device common for all mice
  207. [ 1.337024] i2c /dev entries driver
  208. [ 1.341903] hidraw: raw HID events driver (C) Jiri Kosina
  209. [ 1.347527] usbcore: registered new interface driver usbhid
  210. [ 1.353111] usbhid: USB HID core driver
  211. [ 1.358878] NET: Registered protocol family 10
  212. [ 1.364951] sit: IPv6 over IPv4 tunneling driver
  213. [ 1.370780] NET: Registered protocol family 17
  214. [ 1.375390] Key type dns_resolver registered
  215. [ 1.381350] Loading compiled-in X.509 certificates
  216. [ 1.390453] Key type encrypted registered
  217. [ 1.395322] ubi0: attaching mtd1
  218. [ 1.480010] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
  219. [ 1.541562] ata1.00: HPA detected: current 156299375, native 156301488
  220. [ 1.548083] ata1.00: ATA-7: ST380815AS, 3.AAC, max UDMA/133
  221. [ 1.549772] ubi0: scanning is finished
  222. [ 1.549975] ubi0 error: ubi_read_volume_table: the layout volume was not found
  223. [ 1.550886] ubi0 error: ubi_attach_mtd_dev: failed to attach mtd1, error -22
  224. [ 1.571604] UBI error: cannot attach mtd1
  225. [ 1.571607] ata1.00: 156299375 sectors, multi 0: LBA48 NCQ (depth 0/32)
  226. [ 1.616542] ata1.00: configured for UDMA/133
  227. [ 1.640453] scsi 0:0:0:0: Direct-Access ATA ST380815AS C PQ: 0 ANSI: 5
  228. [ 1.649927] sd 0:0:0:0: [sda] 156299375 512-byte logical blocks: (80.0 GB/74.5 GiB)
  229. [ 1.658654] sd 0:0:0:0: [sda] Write Protect is off
  230. [ 1.663713] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
  231. [ 1.698472] sda: sda1 sda2 sda3
  232. [ 1.704348] sd 0:0:0:0: [sda] Attached SCSI disk
  233. [ 1.734382] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
  234. [ 1.742156] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
  235. [ 1.765342] devtmpfs: mounted
  236. [ 1.768634] Freeing unused kernel memory: 200K (c07ee000 - c0820000)
  237. INIT: version 2.88 booting
  238. [info] Using makefile-style concurrent boot in runlevel S.
  239. [....] Starting the hotplug events dispatcher: udevd[ 3.236339] udevd[187]: starting version 175
  240. . ok
  241. [ 3.472514] cfg80211: Calling CRDA to update world regulatory domain
  242. [ ok ] Synthesizing the initial hotplug events...done.
  243. [ ok ] Waiting for /dev to be fully populated...done.
  244. [ 5.355609] EXT4-fs (sda2): re-mounted. Opts: (null)
  245. [....] Checking root file system...fsck from util-linux 2.20.1
  246. rootfs: clean, 26997/262144 files, 281881/1048576 blocks
  247. done.
  248. [ 5.669125] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
  249. [ ok ] Cleaning up temporary files... /tmp /lib/init/rw.
  250. [ ok ] Loading kernel modules...done.
  251. [ 6.630318] cfg80211: Calling CRDA to update world regulatory domain
  252. [....] Activating lvm and md swap...[ 9.568325] Adding 524284k swap on /swapfile1. Priority:-1 extents:3 across:540668k FS
  253. done.
  254. [....] Checking file systems...fsck from util-linux 2.20.1
  255. [ 9.790108] cfg80211: Calling CRDA to update world regulatory domain
  256. home: clean, 11/4628480 files, 303741/18484493 blocks
  257. [ 9.873221] random: nonblocking pool is initialized
  258. done.
  259. [ ok ] Mounting local filesystems...done.
  260. [ ok ] Activating swapfile swap...done.
  261. [ ok ] Cleaning up temporary files....
  262. [ ok ] Setting kernel variables ...done.
  263. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.2.2
  264. Copyright 2004-2011 Internet Systems Consortium.
  265. All rights reserved.
  266. For info, please visit https://www.isc.org/software/dhcp/
  267.  
  268. Listening on LPF/eth0/74:f0:11:11:11:11
  269. Sending on LPF/eth0/74:f0:11:11:11:11
  270. Sending on Socket/fallback
  271. DHCPREQUEST on eth0 to 255.255.255.255 port 67
  272. [ 12.950018] cfg80211: Calling CRDA to update world regulatory domain
  273. [ 16.110005] cfg80211: Calling CRDA to update world regulatory domain
  274. [ 17.560727] stmmaceth 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
  275. DHCPREQUEST on eth0 to 255.255.255.255 port 67
  276. DHCPACK from 192.168.3.1
  277. [ 19.270056] cfg80211: Calling CRDA to update world regulatory domain
  278. bound to 192.168.3.179 -- renewal in 19909 seconds.
  279. done.
  280. [ ok ] Starting rpcbind daemon....
  281. [ ok ] Starting NFS common utilities: statd idmapd.
  282. [ ok ] Cleaning up temporary files....
  283. INIT: Entering runlevel: 2
  284. [info] Using makefile-style concurrent boot in runlevel 2.
  285. [ 22.440122] cfg80211: Calling CRDA to update world regulatory domain
  286. [ ok ] Starting NTP server: ntpd.
  287. [ ok ] Starting rpcbind daemon...[....] Already running..
  288. [ ok ] Starting system message bus: dbus.
  289. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
  290. 1692 (syslogd)
  291. . ok
  292. [ ok ] Starting NFS common utilities: statd idmapd.
  293. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
  294. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
  295. [warn] Not starting NFS kernel daemon: no exports. ... (warning).
  296. [ ok ] Starting OpenBSD Secure Shell server: sshd.
  297. 1695 (klogd)
  298. . ok
  299. [ 25.610012] cfg80211: Calling CRDA to update world regulatory domain
  300.  
  301. Debian GNU/Linux 7 debian ttyS0
  302.  
  303. debian login: [ 28.770012] cfg80211: Calling CRDA to update world regulatory domain
  304. [ 31.930009] cfg80211: Calling CRDA to update world regulatory domain
  305. [ 35.090017] cfg80211: Exceeded CRDA call max attempts. Not calling CRDA
  306.  
  307. Debian GNU/Linux 7 debian ttyS0
  308.  
  309. debian login: root
  310. Password:
  311. Last login: Wed Dec 31 16:00:40 PST 1969 on ttyS0
  312. Linux debian 4.1.0-oxnas-tld-1 #3 SMP PREEMPT Wed Jul 1 05:11:47 PDT 2015 armv6l
  313.  
  314. The programs included with the Debian GNU/Linux system are free software;
  315. the exact distribution terms for each program are described in the
  316. individual files in /usr/share/doc/*/copyright.
  317.  
  318. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
  319. permitted by applicable law.
  320. root@debian:~#
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!