Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- BUFFALO CFE Version 1.00 [DDRCLK:333]
- decompressing
- Decompressing...done
- Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
- et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)
- DDR clock change and Calibrate... [333->533]
- BUFFALO CFE Version 1.00 [DDRCLK:533]
- Memory Test start(0x07E00000) end(0x08000000) size(2097152)
- Data line test start:0x07e00000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x07e00000 len:0x200000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- decompressing
- Decompressing...done
- Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
- CFE version 6.30.163.18 (r377098) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
- Build Date: Fri Jan 18 16:22:36 JST 2013 (root@fc17.localdomain)
- Copyright (C) 2000-2008 Broadcom Corporation.
- Memory Test start(0x00000000) end(0x07E00000) size(132120576)
- Data line test start:0x00000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x00000000 len:0x7e00000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- Memory Test start(0x88000000) end(0xA0000000) size(402653184)
- Data line test start:0x88000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x88000000 len:0x18000000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- Init Arena
- Init Devs.
- Boot partition size = 262144(0x40000)
- Found a Esmt NAND flash:
- Total size: 128MB
- Block size: 128KB
- Page Size: 2048B
- OOB Size: 64B
- Sector size: 512B
- Spare size: 16B
- ECC level: 8-bit
- Device ID: 0x92 0xf1 0x80 0x95 0x40
- DDR Clock: 533 MHz
- Warning: using legacy sdram_ncdl parameter to set DDR frequency. Equivalent setting in clkfreq=800,*0* will be ignored.
- et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)
- CPU type 0x0: 800MHz
- Tot mem: 524288 KBytes
- CFE mem: 0x07E00000 - 0x07F9A984 (1681796)
- Data: 0x07E53480 - 0x07E53948 (1224)
- BSS: 0x07E53958 - 0x07E98984 (282668)
- Heap: 0x07E98984 - 0x07F98984 (1048576)
- Stack: 0x07F98984 - 0x07F9A984 (8192)
- Text: 0x07E00000 - 0x07E488F0 (297200)
- Boot: 0x07F9B000 - 0x07FDB000
- Reloc: I:00000000 - D:00000000
- Device eth0: hwaddr B2-C7-45-XX-XX-XX, ipaddr 192.168.1.1, mask 255.255.255.0
- gateway not set, nameserver not set
- Startup canceled
- CFE> flash -noheader 192.168.1.2:buffalo-wzr-1750dhp-webflash.bin nflash1.trx
- Reading 192.168.1.2:buffalo-wzr-1750dhp-webflash.bin: Done. 25952256 bytes read
- Programming...done. 25952256 bytes written
- *** command status = 0
- CFE> nvram erase
- *** command status = 0
- CFE> reboot
- BUFFALO CFE Version 1.00 [DDRCLK:333]
- decompressing
- Decompressing...done
- Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
- Corrupt NVRAM found, trying embedded NVRAM next.
- CFE version 6.30.163.18 (r377098) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
- Build Date: Fri Jan 18 16:22:36 JST 2013 (root@fc17.localdomain)
- Copyright (C) 2000-2008 Broadcom Corporation.
- Memory Test start(0x00000000) end(0x07E00000) size(132120576)
- Data line test start:0x00000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x00000000 len:0x7e00000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- Memory Test start(0x88000000) end(0xA0000000) size(402653184)
- Data line test start:0x88000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x88000000 len:0x18000000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- Init Arena
- Init Devs.
- Boot partition size = 262144(0x40000)
- Found a Esmt NAND flash:
- Total size: 128MB
- Block size: 128KB
- Page Size: 2048B
- OOB Size: 64B
- Sector size: 512B
- Spare size: 16B
- ECC level: 8-bit
- Device ID: 0x92 0xf1 0x80 0x95 0x40
- DDR Clock: 333 MHz
- Warning: using legacy sdram_ncdl parameter to set DDR frequency. Equivalent setting in clkfreq=800,*0* will be ignored.
- Warning: invalid DDR setting of 533 MHz ignored. DDR frequency will be set to 333 MHz.
- et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)
- CPU type 0x0: 800MHz
- Tot mem: 524288 KBytes
- CFE mem: 0x07E00000 - 0x07F9A984 (1681796)
- Data: 0x07E53480 - 0x07E53948 (1224)
- BSS: 0x07E53958 - 0x07E98984 (282668)
- Heap: 0x07E98984 - 0x07F98984 (1048576)
- Stack: 0x07F98984 - 0x07F9A984 (8192)
- Text: 0x07E00000 - 0x07E488F0 (297200)
- Boot: 0x07F9B000 - 0x07FDB000
- Reloc: I:00000000 - D:00000000
- initializing nvram...Corrupt NVRAM found, trying embedded NVRAM next.
- done
- commiting nvram...done
- now rebooting
- BUFFALO CFE Version 1.00 [DDRCLK:333]
- decompressing
- Decompressing...done
- Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
- et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)
- DDR clock change and Calibrate... [333->533]
- BUFFALO CFE Version 1.00 [DDRCLK:533]
- Memory Test start(0x07E00000) end(0x08000000) size(2097152)
- Data line test start:0x07e00000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x07e00000 len:0x200000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- decompressing
- Decompressing...done
- Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
- CFE version 6.30.163.18 (r377098) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
- Build Date: Fri Jan 18 16:22:36 JST 2013 (root@fc17.localdomain)
- Copyright (C) 2000-2008 Broadcom Corporation.
- Memory Test start(0x00000000) end(0x07E00000) size(132120576)
- Data line test start:0x00000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x00000000 len:0x7e00000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- Memory Test start(0x88000000) end(0xA0000000) size(402653184)
- Data line test start:0x88000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
- Address line test start:0x88000000 len:0x18000000 pattern 0xAAAAAAAA 0x55555555
- Fill test patnum:2
- fill Pattern 5555AAAA Writing... Reading...
- fill Pattern AAAA5555 Writing... Reading...
- Init Arena
- Init Devs.
- Boot partition size = 262144(0x40000)
- Found a Esmt NAND flash:
- Total size: 128MB
- Block size: 128KB
- Page Size: 2048B
- OOB Size: 64B
- Sector size: 512B
- Spare size: 16B
- ECC level: 8-bit
- Device ID: 0x92 0xf1 0x80 0x95 0x40
- DDR Clock: 533 MHz
- Warning: using legacy sdram_ncdl parameter to set DDR frequency. Equivalent setting in clkfreq=800,*0* will be ignored.
- et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)
- CPU type 0x0: 800MHz
- Tot mem: 524288 KBytes
- CFE mem: 0x07E00000 - 0x07F9A984 (1681796)
- Data: 0x07E53480 - 0x07E53948 (1224)
- BSS: 0x07E53958 - 0x07E98984 (282668)
- Heap: 0x07E98984 - 0x07F98984 (1048576)
- Stack: 0x07F98984 - 0x07F9A984 (8192)
- Text: 0x07E00000 - 0x07E488F0 (297200)
- Boot: 0x07F9B000 - 0x07FDB000
- Reloc: I:00000000 - D:00000000
- Committing NVRAM...done
- Device eth0: hwaddr B2-C7-45-XX-XX-XX, ipaddr 192.168.11.1, mask 255.255.255.0
- gateway not set, nameserver not set
- check_trx: start nflash1.trx
- check_trx: exit nflash1.trx
- Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
- Loading: .. 1652488 bytes read
- Entry at 0x00008000
- Closing network.
- Starting program at 0x00008000
- Uncompressing Linux... done, booting the kernel.
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130816
- Kernel command line: console=ttyS0,115200 panic=10 root=/dev/mtdblock3 earlyprintk=1 rootfstype=squashfs,jffs2 noinitrd init=/bin/sh
- PID hash table entries: 512 (order: -1, 2048 bytes)
- Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
- Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
- Memory: 514324K/524288K available (3446K kernel code, 195K rwdata, 1212K rodata, 348K init, 371K bss, 9964K reserved, 0K cma-reserved, 393216K highmem)
- Virtual kernel memory layout:
- vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
- vmalloc : 0x88800000 - 0xff800000 (1904 MB)
- lowmem : 0x80000000 - 0x88000000 ( 128 MB)
- pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
- modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
- .text : 0x80008000 - 0x80494e1c (4660 kB)
- .init : 0x80495000 - 0x804ec000 ( 348 kB)
- .data : 0x804ec000 - 0x8051cd34 ( 196 kB)
- .bss : 0x8051f000 - 0x8057be0c ( 372 kB)
- Hierarchical RCU implementation.
- CONFIG_RCU_FANOUT set to non-default value of 2
- Build-time adjustment of leaf fanout to 2.
- NR_IRQS:256
- MPCORE GIC init
- soc_dmu_init
- add clk lookups
- MPCORE Global Timer Clock 400000000Hz on IRQ 27
- sched_clock: 32 bits at 400MHz, resolution 2ns, wraps every 5368709118ns
- clocksource: mpcore_gtimer: mask: 0xffffffffffffffff max_cycles: 0x5c4093a7d1, max_idle_ns: 440795210635 ns
- register local timer
- smp_twd: clock not found -2
- Calibrating local timer... 399.68MHz.
- Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- CPU: Testing write buffer coherency: ok
- CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
- 2 cores has been found
- Setting up static identity map for 0x85e0 - 0x8614
- L2C: platform provided aux values permit register corruption.
- L2C: DT/platform modifies aux control register: 0x0a130000 -> 0x7a530000
- L2C-310 erratum 769419 enabled
- L2C-310 enabling early BRESP for Cortex-A9
- L2C-310 full line of zeros enabled for Cortex-A9
- L2C-310 dynamic clock gating enabled, standby mode enabled
- L2C-310 cache controller enabled, 16 ways, 256 kB
- L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x4e530001
- CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
- Brought up 2 CPUs
- SMP: Total of 2 processors activated (3188.32 BogoMIPS).
- clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- futex hash table entries: 512 (order: 3, 32768 bytes)
- NET: Registered protocol family 16
- DMA: preallocated 256 KiB pool for atomic coherent allocations
- coherence_win_size = 10000000
- coherence_flag = FFFFFFF8
- ddr_phys_offset_va =FFFFFFFF
- ddr_phys_offset2_va =A8000000
- Found a ST compatible (Marconix) serial flash with 16 64KB blocks; total size 1MB
- found cfe nvram on sflash
- CCA UART Clock Config: Sel=1 Ovr=1 Div=48
- CCA UART Clock rate 100000000Hz CCB UART Clock rate 100000000Hz
- clocksource: Switched to clocksource mpcore_gtimer
- NET: Registered protocol family 2
- TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
- TCP: Hash tables configured (established 1024 bind 1024)
- UDP hash table entries: 256 (order: 1, 8192 bytes)
- UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- NET: Registered protocol family 1
- init gpio code
- Buffalo WZR-1750DHP
- PCI: no core
- PCI: no core
- PCI: scanning bus 0
- PCI host bridge to bus 0000:00
- pci_bus 0000:00: root bus resource [io 0x0000-0xffffffff]
- pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
- pci_bus 0000:00: root bus resource [bus 00-ff]
- pci 0000:00:0f.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
- PCI: Fixing up bus 0 domain 0
- PCIE1 link=1
- PCIE1 switching to GEN2
- PCIE1 link=1
- PCI host bridge to bus 0001:00
- pci_bus 0001:00: root bus resource [mem 0x08000000-0x0fffffff]
- pci_bus 0001:00: No busn resource found for root bus, will use [bus 00-ff]
- PCI: Fixing up bus 0 domain 1
- PCI: bus0: Fast back to back transfers disabled
- pci 0001:01:00.0: Max Payload Size set to 512 (was 128, max 512)
- PCI: Fixing up bus 1 domain 1
- PCI: bus1: Fast back to back transfers disabled
- pci 0001:00:00.0: BAR 8: assigned [mem 0x08000000-0x080fffff]
- pci 0001:01:00.0: BAR 0: assigned [mem 0x08000000-0x08007fff 64bit]
- pci 0001:00:00.0: PCI bridge to [bus 01]
- pci 0001:00:00.0: bridge window [mem 0x08000000-0x080fffff]
- PCIE2 link=1
- PCIE2 switching to GEN2
- PCIE2 link=1
- PCI host bridge to bus 0002:00
- pci_bus 0002:00: root bus resource [mem 0x40000000-0x47ffffff]
- pci_bus 0002:00: No busn resource found for root bus, will use [bus 00-ff]
- PCI: Fixing up bus 0 domain 2
- PCI: bus0: Fast back to back transfers disabled
- pci 0002:01:00.0: can't set Max Payload Size to 512; if necessary, use "pci=pcie_bus_safe" and report a bug
- PCI: Fixing up bus 1 domain 2
- PCI: bus1: Fast back to back transfers disabled
- pci 0002:00:00.0: BAR 8: assigned [mem 0x40000000-0x400fffff]
- pci 0002:01:00.0: BAR 0: assigned [mem 0x40000000-0x40003fff 64bit]
- pci 0002:00:00.0: PCI bridge to [bus 01]
- pci 0002:00:00.0: bridge window [mem 0x40000000-0x400fffff]
- PCIE3 link=0
- squashfs: version 4.0 (2009/01/31) Phillip Lougher
- io scheduler noop registered (default)
- io scheduler cfq registered
- serial8250_init
- Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
- console [ttyS0] disabled
- serial8250.0: ttyS0 at MMIO 0x18000300 (irq = 117, base_baud = 6250000) is a 16550
- console [ttyS0] enabled
- serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117, base_baud = 6250000) is a 16550
- brd: module loaded
- loop: module loaded
- Creating 5 MTD partitions on "bcmsflash":
- 0x000000000000-0x000000100000 : "boot"
- 0x000000000000-0x0000000f0000 : "linux"
- 0x000000100000-0x000000100000 : "rootfs"
- mtd: partition "rootfs" is out of reach -- disabled
- 0x0000000f0000-0x000000100000 : "nvram_cfe"
- 0x0000000e0000-0x0000000f0000 : "nvram"
- Found a Esmt NAND flash:
- Total size: 128MB
- Block size: 128KB
- Page Size: 2048B
- OOB Size: 64B
- Sector size: 512B
- Spare size: 16B
- ECC level: 8 (8-bit)
- Device ID: 0x92 0xf1 0x80 0x95 0x40 0x7f
- Creating 1 MTD partitions on "nflash":
- 0x000000000000-0x000008000000 : "nand"
- PPP generic driver version 2.4.2
- PPP BSD Compression module registered
- PPP Deflate Compression module registered
- PPP MPPE Compression module registered
- NET: Registered protocol family 24
- GACT probability NOT on
- Mirror/redirect action on
- Simple TC action Loaded
- netem: version 1.3
- u32 classifier
- Performance counters on
- input device check on
- Actions configured
- Netfilter messages via NETLINK v0.30.
- nf_conntrack version 0.5.0 (8036 buckets, 32144 max)
- nf_conntrack_rtsp v0.7 loading
- xt_time: kernel timezone is -0000
- ip_set: protocol 6
- gre: GRE over IPv4 demultiplexor driver
- nf_nat_rtsp v0.7 loading
- ip_tables: (C) 2000-2006 Netfilter Core Team
- NET: Registered protocol family 17
- bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- Bridge firewalling registered
- 8021q: 802.1Q VLAN Support v1.8
- Registering SWP/SWPB emulation handler
- found cfe nvram
- check if nvram copy is required CFE Size is 65536
- nvram copy magic is 48534C46
- max nvram space = 131072
- read 65536 bytes to offset 0
- Key type encrypted registered
- Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
- nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1
- nand: Eon NAND 128MiB 3,3V 8-bit
- nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
- Spare area=64 eccbytes 56, ecc bytes located at:
- 2 3 4 5 6 7 8 9 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 50 51 52 53 54 55 56 57 58 59 60 61 62 63
- Available 7 bytes at (off,len):
- (1,1) (16,2) (32,2) (48,2) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0)
- Scanning device for bad blocks
- Options: NO_SUBPAGE_WRITE,
- Creating 1 MTD partitions on "brcmnand":
- 0x000000000000-0x000008000000 : "ddwrt"
- blk_update_request: I/O error, dev mtdblock2, sector 0
- SQUASHFS error: squashfs_read_data failed to read block 0x0
- squashfs: SQUASHFS error: unable to read squashfs_super_block
- VFS: Cannot open root device "1f02" or unknown-block(31,2): error -5
- Please append a correct "root=" boot option; here are the available partitions:
- 0100 4096 ram0 (driver?)
- 0101 4096 ram1 (driver?)
- 0102 4096 ram2 (driver?)
- 0103 4096 ram3 (driver?)
- 0104 4096 ram4 (driver?)
- 0105 4096 ram5 (driver?)
- 0106 4096 ram6 (driver?)
- 0107 4096 ram7 (driver?)
- 0108 4096 ram8 (driver?)
- 0109 4096 ram9 (driver?)
- 010a 4096 ram10 (driver?)
- 010b 4096 ram11 (driver?)
- 010c 4096 ram12 (driver?)
- 010d 4096 ram13 (driver?)
- 010e 4096 ram14 (driver?)
- 010f 4096 ram15 (driver?)
- 1f00 1024 mtdblock0 (driver?)
- 1f01 960 mtdblock1 (driver?)
- 1f03 64 mtdblock3 (driver?)
- 1f04 64 mtdblock4 (driver?)
- 1f05 131072 mtdblock5 (driver?)
- 1f06 131072 mtdblock6 (driver?)
- Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)
- CPU0: stopping
- CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.159 #4001
- Hardware name: Northstar Prototype
- Backtrace:
- [<8001b99c>] (dump_backtrace) from [<8001bc24>] (show_stack+0x18/0x1c)
- r7:00000000 r6:60000193 r5:00000000 r4:8050cda0
- [<8001bc0c>] (show_stack) from [<80164688>] (dump_stack+0x90/0xa4)
- [<801645f8>] (dump_stack) from [<8001d788>] (handle_IPI+0x110/0x1a8)
- r7:00000000 r6:00000000 r5:804edf20 r4:8051f1a0
- [<8001d678>] (handle_IPI) from [<80009398>] (gic_handle_irq+0x78/0x7c)
- r7:b0100100 r6:804edf20 r5:b010010c r4:804fbb18
- [<80009320>] (gic_handle_irq) from [<80009ea0>] (__irq_svc+0x40/0x54)
- Exception stack(0x804edf20 to 0x804edf68)
- df20: 86bd4240 00000000 000005ec 8000a980 ffffe000 804fb8e0 804e7220 8042f054
- df40: 8051f01c 804be8c8 00000000 804edf7c 804edf80 804edf70 80019598 8001959c
- df60: 60000013 ffffffff
- r9:804be8c8 r8:8051f01c r7:804edf54 r6:ffffffff r5:60000013 r4:8001959c
- [<80019560>] (arch_cpu_idle) from [<8006c6f8>] (default_idle_call+0x30/0x34)
- [<8006c6c8>] (default_idle_call) from [<8006c81c>] (cpu_startup_entry+0x120/0x15c)
- [<8006c6fc>] (cpu_startup_entry) from [<80012a48>] (rest_init+0x80/0x84)
- r7:8051f020 r4:00000000
- [<800129c8>] (rest_init) from [<80495ca8>] (start_kernel+0x318/0x324)
- [<80495990>] (start_kernel) from [<0000807c>] (0x807c)
- r9:413fc090 r8:0000406a r7:80501d94 r6:804be8c4 r5:804fb860 r4:8051f090
- Rebooting in 10 seconds..
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement