WL700 serial boot fail 001

CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: | 12 29 20:36:58 CST 2005 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.

Initializing Arena
Initializing Devices.
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.23.0
rndis0: Broadcom USB RNDIS Network Adapter (P-t-P)
CPU type 0x29006: 264MHz
Total memory: 67108864 KBytes

Total memory used by CFE:  0x80800000 - 0x8089BA00 (637440)
Initialized Data:          0x80831B70 - 0x80834250 (9952)
BSS Area:                  0x80834250 - 0x80835A00 (6064)
Local Heap:                0x80835A00 - 0x80899A00 (409600)
Stack Area:                0x80899A00 - 0x8089BA00 (8192)
Text (code) segment:       0x80800000 - 0x80831B70 (203632)
Boot area (physical):      0x0089C000 - 0x008DC000
Relocation Factor:         I:00000000 - D:00000000

Device eth0:  hwaddr 00-1A-92-D9-02-CD, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Null Rescue Flag.
Null Restore Flag.
set pivot_wait = 0
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: ..... 2736128 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
CPU revision is: 00029006

Primary instruction cache 16kb, linesize 16 bytes (2 ways)

Primary data cache 16kb, linesize 16 bytes (2 ways)

RAC:  CR0:00000015  CR1:03ff0000

Linux version 2.4.20 (root@localhost.localdomain) (gcc version 3.0 20010422 (prerelease) with bcm4710a0 modifications) #40 T 6 27 21:33:12 CST 2007

BCM47XX ChipID = 0x4704, RevisionID = 8, Options = 0x2

Setting GPIO 3 to output of 1.
Setting GPIO 6 to output of 1.
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
CPU: BCM4704 rev 8 at 264 MHz
Calibrating delay loop... 263.78 BogoMIPS
Memory: 61884k/65536k available (2430k kernel code, 3652k reserved, 136k data, 84k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
mount init
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
do kern mount [rootfs]
do kern mount [bdev]
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
do kern mount [proc]
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Fixing up bus 1
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
do kern mount [sockfs]
Initializing RT netlink socket
Starting kswapd
do kern mount [tmpfs]
do kern mount [pipefs]
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
do kern mount [devfs]
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver v1.1.22 [Flags: R/O]
do kern mount [devpts]
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-bit.o: i2c bit algorithm module
i2c-proc.o version 2.6.1 (20010825)
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xb8000300 (irq = 3) is a 16550A
ttyS01 at 0xb8000400 (irq = 0) is a 16550A
Generic MIPS RTC Driver v1.0
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AEC6265: IDE controller on PCI bus 01 dev 10
PCI: Enabling device 01:02.0 (0000 -> 0003)
AEC6265: chipset revision 16
AEC6265: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AEC6265: ROM disabled at 0x00000000
    ide2: BM-DMA at 0x0180-0x0187, BIOS settings: hde:pio, hdf:pio
    ide3: BM-DMA at 0x0188-0x018f, BIOS settings: hdg:pio, hdh:pio

PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
 Amd/Fujitsu Extended Query Table v1.0 at 0x0040

Physically mapped flash: JEDEC Device ID is 0xC4. Assuming broken CFI table.
Physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
Flash device: 0x200000 at 0x1c000000
Physically mapped flash: cramfs filesystem found at block 1412
Creating 4 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x001f0000 : "linux"
0x00161360-0x001f0000 : "rootfs"
0x001f0000-0x00200000 : "nvram"

sflash: found no supported devices
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Enabling device 01:03.2 (0000 -> 0002)
ehci_hcd 01:03.2: PCI device 1106:3104
ehci_hcd 01:03.2: irq 2, pci mem c000d000
usb.c: new USB bus registered, assigned bus number 1

ECHI PCI device 31041106 found.
ECHI reg 0x49 = 80243420
ECHI reg 0x49 changed to = 80243400
ECHI reg 0x4b = 80243409
ECHI reg 0x4b changed to = 80243429
PCI: 01:03.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW, correcting to 32
ehci_hcd 01:03.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 4 ports detected
host/usb-uhci.c: $Revision: 1.275 $ time 21:34:18 Jun 27 2007
host/usb-uhci.c: High bandwidth mode enabled
PCI: Enabling device 01:03.0 (0000 -> 0001)
ECHI PCI device 30381106 found.
UCHI reg 0x41 = 10
UCHI reg 0x41 changed to = 0
host/usb-uhci.c: USB UHCI at I/O 0x200, IRQ 2
host/usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Enabling device 01:03.1 (0000 -> 0001)
ECHI PCI device 30381106 found.
UCHI reg 0x41 = 10
UCHI reg 0x41 changed to = 0
host/usb-uhci.c: USB UHCI at I/O 0x220, IRQ 2
host/usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
host/usb-ohci.c: USB OHCI at membase 0xb8003000, IRQ 6
host/usb-ohci.c: usb-00:03.0, PCI device 14e4:4715
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Skipping autodetection of RAID arrays.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
sys mount [dev:devfs][dir:/dev][type:devfs]
sys mount: type:devfs, data_page:0
mount type: devfs 0
do mount[dev:devfs][dir:/dev][type:devfs]
do add mount [T:devfs], [devfs]
do kern mount [devfs]
sys mount [dev:/dev/root][dir:/root][type:cramfs]
sys mount: type:cramfs, data_page:0
mount type: cramfs 0
do mount[dev:/dev/root][dir:/root][type:cramfs]
do add mount [T:cramfs], [/dev/root]
do kern mount [/dev/root]
VFS: Mounted root (cramfs filesystem) readonly.
sys mount [dev:.][dir:/][type:<NULL>]
sys mount: type:<NULL>, data_page:0
mount type: <NULL> 0
do mount[dev:.][dir:/][type:<NULL>]
do move mount [.]
do mount[dev:none][dir:/dev][type:devfs]
do add mount [T:devfs], [none]
do kern mount [none]
Mounted devfs on /dev
Freeing unused kernel memory: 84k freed
Algorithmics/MIPS FPU Emulator v1.5


### pivot_erasedisk check ###
sys mount [dev:proc][dir:/proc][type:proc]
sys mount: type:proc, data_page:0
mount type: proc 0
do mount[dev:proc][dir:/proc][type:proc]
do add mount [T:proc], [proc]
do kern mount [proc]

pivot_rc startinsys mount [dev:/dev/ide/host2/bus0/target0/lun0/part1][dir:/mnt][type:cramfs]
g...
pivot_rc psys mount: type:cramfs, data_page:0
roceeding to boomount type: cramfs 0
t from disk...
do mount[dev:/dev/ide/host2/bus0/target0/lun0/part1][dir:/mnt][type:cramfs]
do add mount [T:cramfs], [/dev/ide/host2/bus0/target0/lun0/part1]
do kern mount [/dev/ide/host2/bus0/target0/lun0/part1]
ERROR(a):mount_pivot_point failesys mount [dev:/dev/ide/host2/bus0/target0/lun0/part2][dir:/mnt][type:cramfs]
d to mount locatsys mount: type:cramfs, data_page:0
ion : /dev/ide/hmount type: cramfs 0
ost2/bus0/targetdo mount[dev:/dev/ide/host2/bus0/target0/lun0/part2][dir:/mnt][type:cramfs]
0/lun0/part1...
do add mount [T:cramfs], [/dev/ide/host2/bus0/target0/lun0/part2]

ERROR(b):mount_do kern mount [/dev/ide/host2/bus0/target0/lun0/part2]

pivot_point error : No such file or directory...
pivot_rc boot loop error for location 0...
ERROR(a):mount_pivot_point failed to mount location : /dev/ide/host2/bus0/target0/lun0/part2...
ERROR(b):mount_pivot_point error : No such file or directory...
pivot_rc boot loop error for location 1...
pivot_rc did not boot -> hang wait for network loading...
Using /lib/modules/2.4.20/kernel/drivers/net/et/et.o
Symbol version prefix ''
Warning: loading /lib/modules/2.4.20/kernel/drivers/net/et/et.o will taint the kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about tainted modules


 ## robo disable vlan ##

eth0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.39.0

Module et loaded, with warnings
vlan0: No such device
eth1: No such device
eth0: No such process
Waiting for new image on IP 192.168.1.1.
Waiting for announcement from download server...