Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- BL2 Built : 12:23:15, May 17 2019. gxl g3e531ea - luan.yuan@droid15-sz
- set vdd cpu_a to 1120 mv
- set vdd cpu_b to 1050 mv
- set vddee to 1000 mv
- Board ID = 6
- CPU clk: 1200MHz
- DQS-corr enabled
- DDR scramble enabled
- DDR3 chl: Rank0+1 @ 912MHz - FAIL
- DDR3 chl: Rank0 @ 912MHz - FAIL
- DDR3 chl: Rank0 16bit @ 912MHz - FAIL
- DDR4 chl: Rank0+1 @ 1008MHz
- bist_test rank: 0 15 0b 1f 28 18 39 13 08 1f 2a 1a 3b 19 10 22 23 13 34 17 10 1f 24 13 36 740 rank: 1 18 03 2d 29 18 3a 15 04 27 2a 1a 3a 1b 07 2f 25 13 37 1e 0b 31 24 13 36 740 - PASS
- Rank0: 2048MB(auto)-2T-18
- Rank1: 1024MB(auto)-2T-18
- AddrBus test pass!
- eMMC boot @ 0
- sw8 s
- emmc switch 3 ok
- Authentication key not yet programmed
- get rpmb counter error 0x00000007
- emmc switch 0 ok
- Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000, part: 0
- New fip structure!
- Load bl30 from eMMC, src: 0x00010200, des: 0x013c0000, size: 0x0000d600, part: 0
- Load bl31 from eMMC, src: 0x00020200, des: 0x05100000, size: 0x0002b400, part: 0
- Load bl33 from eMMC, src: 0x0004c200, des: 0x01000000, size: 0x00070200, part: 0
- NOTICE: BL3-1: v1.0(release):53f813e
- NOTICE: BL3-1: Built : 15:51:23, May 22 2019
- NOTICE: BL3-1: GXM normal boot!
- NOTICE: BL3-1: BL33 decompress pass
- mpu_config_enable:system pre init ok
- dmc sec lock
- [Image: gxl_v1.1.3386-3b31431 2019-05-21 10:41:39 luan.yuan@droid15-sz]
- OPS=0x82
- wdt: reset registers!
- 22 0b 82 00 05 a2 0b 0b 8b 72 a2 e6 83 5b fc 79
- [0.824496 Inits done]
- secure task start!
- high task start!
- low task start!
- ERROR: Error initializing runtime service opteed_fast
- U-Boot 2015.01-g6ab671a0b4-dirty (Dec 06 2019 - 11:47:30)
- DRAM: 3 GiB
- Relocation Offset is: b6e97000
- spi_post_bind(spifc): req_seq = 0
- register usb cfg[0][1] = 00000000b7f4cbc8
- [CANVAS]canvas init
- aml_i2c_init_port init regs for 2
- MMC: aml_priv->desc_buf = 0x00000000b3e97720
- aml_priv->desc_buf = 0x00000000b3e99a60
- SDIO Port B: 0, SDIO Port C: 1
- co-phase 0x2, tx-dly 0, clock 400000
- co-phase 0x2, tx-dly 0, clock 400000
- co-phase 0x2, tx-dly 0, clock 400000
- emmc/sd response timeout, cmd8, status=0x3ff2800
- emmc/sd response timeout, cmd55, status=0x3ff2800
- co-phase 0x2, tx-dly 0, clock 400000
- co-phase 0x2, tx-dly 0, clock 40000000
- [mmc_startup] mmc refix success
- init_part() 282: PART_TYPE_DOS
- [mmc_init] mmc init success
- start dts,buffer=00000000b3e9c2d0,dt_addr=00000000b3e9c2d0
- check_valid_dts: FDT_ERR_BADMAGIC
- get_partition_from_dts() 91: ret -9
- get_partition_from_dts() 94: ret -9
- get_ptbl_from_dtb()-272: get partition table from dts faild
- mmc_device_init()-1254: get partition table from dtb failed
- get_ptbl_rsv()-494: magic faild MPT,
- mmc_device_init()-1281: dtb&rsv are not exist, no LPT source
- get partition info failed !!
- Using default environment
- In: serial
- Out: serial
- Err: serial
- [i] uboot BOOTED from: 1 - emmc
- [i] KEYS PRW: MCU:
- reboot_mode=cold_boot
- [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
- _verify_dtb_checksum()-3406: calc 0, store 0
- update_dtb_info()-3514: cpy 1 is not valid
- _verify_dtb_checksum()-3406: calc 0, store 0
- update_dtb_info()-3514: cpy 0 is not valid
- dtb_read()-3623: total valid 0
- emmc - EMMC sub system
- Usage:
- emmc dtb_read addr size
- emmc dtb_write addr size
- emmc erase dtb
- emmc erase key
- emmc fastboot_read addr size
- emmc fastboot_write addr size
- vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
- vpu: clk_level = 7
- vpu: vpu_power_on
- vpu: set clk: 666667000Hz, readback: 666666667Hz(0x300)
- vpu: vpu_module_init_config
- vpp: vpp_init
- cvbs: cpuid:0x22
- hpd_state=0
- cvbs: outputmode[1080p60hz] is invalid
- vpp: vpp_matrix_update: 2
- set hdmitx VIC = 16
- config HPLL = 2970000
- HPLL: 0xc000027b
- config HPLL done
- j = 6 vid_clk_div = 1
- hdmitx: set enc for VIC: 16
- HDMITX-DWC addr=0x10004006 rd_data=0x40
- Error: HDMITX-DWC exp_data=0xff mask=0x9f
- rx version is 1.4 or below div=10
- hdmtix: set audio
- hdmitx phy setting done
- vpp: vpp_pq_load pq val error !!!
- Net: Phy 0 not found
- dwmac.c9410000[KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
- MACADDR:02:8b:0b:0b:a2:05(from chipid)
- Warning: dwmac.c9410000 MAC addresses don't match:
- Address in SROM is 86:82:85:d3:77:aa
- Address in environment is 02:8b:0b:0b:a2:05
- upgrade_step=0
- reboot_mode:::: cold_boot
- [KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
- [OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
- [OSD]fb_addr for logo: 0x3d800000
- [OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
- [OSD]fb_addr for logo: 0x3d800000
- [OSD]VPP_OFIFO_SIZE:0xfff00fff
- [CANVAS]addr=0x3d800000 width=3840, height=2160
- Cannot find dev.
- amlmmc cmd <NULL> failed
- store - STORE sub-system
- Usage:
- store init flag
- store read name addr off|partition size
- read 'size' bytes starting at offset 'off'
- to/from memory address 'addr', skipping bad blocks.
- store write name addr off|partition size
- write 'size' bytes starting at offset 'off'
- to/from memory address 'addr', skipping bad blocks.
- store rom_write add off size.
- write uboot to the boot device
- store erase boot/data:
- erase the area which is uboot or data
- store erase partition <partition_name>:
- erase the area which partition in u-boot
- store erase dtb
- store erase key
- store disprotect key
- store rom_protect on/off
- store scrub off|partition size
- scrub the area from offset and size
- store dtb iread/read/write addr <size>
- read/write dtb, size is optional
- store key read/write addr <size>
- read/write key, size is optional
- store ddr_parameter read/write addr <size>
- read/write ddr parameter, size is optional
- store mbr addr
- update mbr/partition table by dtb
- [burnup]Err:store_read_ops,L84:cmd failed, ret=1, [store read logo 0x1080000 0x0 0x2000]
- Err imgread(L537):Fail to read 0x2000B from part[logo] at offset 0
- Error: Bad gzipped data
- There is no valid bmp file at the given address
- [OSD]osd_hw.free_dst_data: 0,1919,0,1079
- [KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
- saradc - saradc sub-system
- Usage:
- saradc saradc open <channel> - open a SARADC channel
- saradc close - close the SARADC
- saradc getval - get the value in current channel
- saradc test - test the SARADC by channel-7
- saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
- gpio: pin GPIOAO_2 (gpio 102) value is 1
- saradc: 0x202, hw_ver: 0x22 (VIM2.V12)
- Product checking: pass! Hardware version: VIM2.V12
- reboot_mode=cold_boot
- ** Invalid partition 5 **
- [aml_i2c_xfer] error ret = -110 i2c master a current slave addr is 0x18
- i2c_read: i2c transfer failed
- Error reading the chip: -110
- [aml_i2c_xfer] error ret = -110 i2c master a current slave addr is 0x18
- i2c_read: i2c transfer failed
- Error reading the chip: -110
- state err
- [aml_i2c_xfer] error ret = -110 i2c master a current slave addr is 0x18
- i2c_read: i2c transfer failed
- Error reading the chip: -110
- boot wol: disable
- [KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
- Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
- kvim2#
- kvim2#
- kvim2#
- kvim2#
- kvim2#
- kvim2#
- kvim2#
- kvim2#
- kvim2#
- kvim2#version
- U-Boot 2015.01-g6ab671a0b4-dirty (Dec 06 2019 - 11:47:30)
- aarch64-none-elf-gcc (crosstool-NG linaro-1.13.1-4.8-2013.11 - Linaro GCC 2013.10) 4.8.3 20131111 (prerelease)
- GNU ld (crosstool-NG linaro-1.13.1-4.8-2013.11 - Linaro GCC 2013.10) 2.23.2.20130610 Linaro 2013.10-4
- kvim2#�GX�GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
- TE: 89224
- BL2 Built : 12:23:15, May 17 2019. gxl g3e531ea - luan.yuan@droid15-sz
- set vdd cpu_a to 1120 mv
- set vdd cpu_b to 1050 mv
- set vddee to 1000 mv
- Board ID = 6
- CPU clk: 1200MHz
- DQS-corr enabled
- DDR scramble enabled
- DDR3 chl: Rank0+1 @ 912MHz - FAIL
- DDR3 chl: Rank0 @ 912MHz - FAIL
- DDR3 chl: Rank0 16bit @ 912MHz - FAIL
- DDR4 chl: Rank0+1 @ 1008MHz
- bist_test rank: 0 14 0b 1e 28 17 3a 13 08 1f 2a 1a 3a 19 10 22 23 13 34 18 10 20 25 13 38 740 rank: 1 18 03 2d 27 16 39 17 05 29 29 19 39 1a 06 2f 24 13 36 1e 0c 31 24 13 36 740 - PASS
- Rank0: 2048MB(auto)-2T-18
- Rank1: 1024MB(auto)-2T-18
- AddrBus test pass!
- eMMC boot @ 0
- sw8 s
- emmc switch 3 ok
- Authentication key not yet programmed
- get rpmb counter error 0x00000007
- emmc switch 0 ok
- Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000, part: 0
- New fip structure!
- Load bl30 from eMMC, src: 0x00010200, des: 0x013c0000, size: 0x0000d600, part: 0
- Load bl31 from eMMC, src: 0x00020200, des: 0x05100000, size: 0x0002b400, part: 0
- Load bl33 from eMMC, src: 0x0004c200, des: 0x01000000, size: 0x00070200, part: 0
- NOTICE: BL3-1: v1.0(release):53f813e
- NOTICE: BL3-1: Built : 15:51:23, May 22 2019
- NOTICE: BL3-1: GXM normal boot!
- NOTICE: BL3-1: BL33 decompress pass
- mpu_config_enable:system pre init ok
- dmc sec lock
- [Image: gxl_v1.1.3386-3b31431 2019-05-21 10:41:39 luan.yuan@droid15-sz]
- OPS=0x82
- wdt: reset registers!
- 22 0b 82 00 05 a2 0b 0b 8b 72 a2 e6 83 5b fc 79
- [0.826168 Inits done]
- secure task start!
- high task start!
- low task start!
- ERROR: Error initializing runtime service opteed_fast
- U-Boot 2015.01-g6ab671a0b4-dirty (Dec 06 2019 - 11:47:30)
- DRAM: 3 GiB
- Relocation Offset is: b6e97000
- spi_post_bind(spifc): req_seq = 0
- register usb cfg[0][1] = 00000000b7f4cbc8
- [CANVAS]canvas init
- aml_i2c_init_port init regs for 2
- MMC: aml_priv->desc_buf = 0x00000000b3e97720
- aml_priv->desc_buf = 0x00000000b3e99a60
- SDIO Port B: 0, SDIO Port C: 1
- co-phase 0x2, tx-dly 0, clock 400000
- co-phase 0x2, tx-dly 0, clock 400000
- co-phase 0x2, tx-dly 0, clock 400000
- emmc/sd response timeout, cmd8, status=0x3ff2800
- emmc/sd response timeout, cmd55, status=0x3ff2800
- co-phase 0x2, tx-dly 0, clock 400000
- co-phase 0x2, tx-dly 0, clock 40000000
- [mmc_startup] mmc refix success
- init_part() 282: PART_TYPE_DOS
- [mmc_init] mmc init success
- start dts,buffer=00000000b3e9c2d0,dt_addr=00000000b3e9c2d0
- check_valid_dts: FDT_ERR_BADMAGIC
- get_partition_from_dts() 91: ret -9
- get_partition_from_dts() 94: ret -9
- get_ptbl_from_dtb()-272: get partition table from dts faild
- mmc_device_init()-1254: get partition table from dtb failed
- get_ptbl_rsv()-494: magic faild MPT,
- mmc_device_init()-1281: dtb&rsv are not exist, no LPT source
- get partition info failed !!
- Using default environment
- In: serial
- Out: serial
- Err: serial
- [i] uboot BOOTED from: 1 - emmc
- [i] KEYS PRW: 1 MCU:
- reboot_mode=cold_boot
- [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
- _verify_dtb_checksum()-3406: calc 0, store 0
- update_dtb_info()-3514: cpy 1 is not valid
- _verify_dtb_checksum()-3406: calc 0, store 0
- update_dtb_info()-3514: cpy 0 is not valid
- dtb_read()-3623: total valid 0
- emmc - EMMC sub system
- Usage:
- emmc dtb_read addr size
- emmc dtb_write addr size
- emmc erase dtb
- emmc erase key
- emmc fastboot_read addr size
- emmc fastboot_write addr size
- vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
- vpu: clk_level = 7
- vpu: vpu_power_on
- vpu: set clk: 666667000Hz, readback: 666666667Hz(0x300)
- vpu: vpu_module_init_config
- vpp: vpp_init
- cvbs: cpuid:0x22
- hpd_state=0
- cvbs: outputmode[1080p60hz] is invalid
- vpp: vpp_matrix_update: 2
- set hdmitx VIC = 16
- config HPLL = 2970000
- HPLL: 0xc000027b
- config HPLL done
- j = 6 vid_clk_div = 1
- hdmitx: set enc for VIC: 16
- HDMITX-DWC addr=0x10004006 rd_data=0x40
- Error: HDMITX-DWC exp_data=0xff mask=0x9f
- rx version is 1.4 or below div=10
- hdmtix: set audio
- hdmitx phy setting done
- vpp: vpp_pq_load pq val error !!!
- Net: Phy 0 not found
- dwmac.c9410000[KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
- MACADDR:02:8b:0b:0b:a2:05(from chipid)
- Warning: dwmac.c9410000 MAC addresses don't match:
- Address in SROM is a6:b7:6b:b2:e1:64
- Address in environment is 02:8b:0b:0b:a2:05
- upgrade_step=0
- reboot_mode:::: cold_boot
- [KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
- [OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
- [OSD]fb_addr for logo: 0x3d800000
- [OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
- [OSD]fb_addr for logo: 0x3d800000
- [OSD]VPP_OFIFO_SIZE:0xfff00fff
- [CANVAS]addr=0x3d800000 width=3840, height=2160
- Cannot find dev.
- amlmmc cmd <NULL> failed
- store - STORE sub-system
- Usage:
- store init flag
- store read name addr off|partition size
- read 'size' bytes starting at offset 'off'
- to/from memory address 'addr', skipping bad blocks.
- store write name addr off|partition size
- write 'size' bytes starting at offset 'off'
- to/from memory address 'addr', skipping bad blocks.
- store rom_write add off size.
- write uboot to the boot device
- store erase boot/data:
- erase the area which is uboot or data
- store erase partition <partition_name>:
- erase the area which partition in u-boot
- store erase dtb
- store erase key
- store disprotect key
- store rom_protect on/off
- store scrub off|partition size
- scrub the area from offset and size
- store dtb iread/read/write addr <size>
- read/write dtb, size is optional
- store key read/write addr <size>
- read/write key, size is optional
- store ddr_parameter read/write addr <size>
- read/write ddr parameter, size is optional
- store mbr addr
- update mbr/partition table by dtb
- [burnup]Err:store_read_ops,L84:cmd failed, ret=1, [store read logo 0x1080000 0x0 0x2000]
- Err imgread(L537):Fail to read 0x2000B from part[logo] at offset 0
- Error: Bad gzipped data
- There is no valid bmp file at the given address
- [OSD]osd_hw.free_dst_data: 0,1919,0,1079
- [KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
- saradc - saradc sub-system
- Usage:
- saradc saradc open <channel> - open a SARADC channel
- saradc close - close the SARADC
- saradc getval - get the value in current channel
- saradc test - test the SARADC by channel-7
- saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
- gpio: pin GPIOAO_2 (gpio 102) value is 1
- saradc: 0x201, hw_ver: 0x22 (VIM2.V12)
- Product checking: pass! Hardware version: VIM2.V12
- reboot_mode=cold_boot
- ** Invalid partition 5 **
- [aml_i2c_xfer] error ret = -110 i2c master a current slave addr is 0x18
- i2c_read: i2c transfer failed
- Error reading the chip: -110
- [aml_i2c_xfer] error ret = -110 i2c master a current slave addr is 0x18
- i2c_read: i2c transfer failed
- Error reading the chip: -110
- state err
- [aml_i2c_xfer] error ret = -110 i2c master a current slave addr is 0x18
- i2c_read: i2c transfer failed
- Error reading the chip: -110
- boot wol: disable
- [KM]Error:f[keymanage_dts_parse]L307:not a fdt at 0x0000000001000000
- Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
- [aml_i2c_xfer] error ret = -110 i2c master a current slave addr is 0x18
- i2c_write: i2c transfer failed
- Error writing the chip: -110
- [aml_i2c_xfer] error ret = -110 i2c master a current slave addr is 0x18
- i2c_read: i2c transfer failed
- Error reading the chip: -110
- [BL31]: tee size: 0
- mac address: 98:aa:fc:60:48:ce
- cfgload: start ...
- cfgload: reading /boot.ini from mmc 0:1 ...
- card in
- co-phase 0x2, tx-dly 0, clock 400000
- co-phase 0x2, tx-dly 0, clock 400000
- co-phase 0x2, tx-dly 0, clock 400000
- co-phase 0x2, tx-dly 0, clock 400000
- co-phase 0x2, tx-dly 0, clock 40000000
- [mmc_startup] mmc refix success
- init_part() 282: PART_TYPE_DOS
- [mmc_init] mmc init success
- reading /boot.ini
- 3644 bytes read in 4 ms (889.6 KiB/s)
- cfgload: applying boot.ini...
- [#] Script a:b3e88fc0 l:3613 c:0 s:0 - run
- reading openwrt.label
- 8 bytes read in 3 ms (2 KiB/s)
- [i] openwrt loaded load mmc 0:1
- load env
- load mmc 0:1 0x32000000 /boot/user.env
- reading /boot/user.env
- 153 bytes read in 4 ms (37.1 KiB/s)
- env import -t 0x32000000 99
- load dtb
- load mmc 0:1 0x1000000 /boot/krescue-vim2.dtb
- reading /boot/krescue-vim2.dtb
- 28350 bytes read in 7 ms (3.9 MiB/s)
- load logo
- load mmc 0:1 0x30000000 /boot/splash.bmp.gz
- reading /boot/splash.bmp.gz
- 20203 bytes read in 6 ms (3.2 MiB/s)
- load packed kernel
- load mmc 0:1 0x6000000 /boot/uImage.gzip
- reading /boot/uImage.gzip
- 6323619 bytes read in 347 ms (17.4 MiB/s)
- [i] bootargs: console=tty0 console=ttyAML0,115200n8 console=ttyS0,115200n8 no_console_suspend consoleblank=0 dtb=/boot/krescue-vim2.dtb booted=emmc hwver=VIM2.V12 root=/dev/mmcblk0p2 rootwait script=sd:*.sh rw panic=10 net.ifnames=0 loglevel=4 fbcon=font:TER16x32 video=HDMI-A-1:1920x1080@60e vt.default_utf8=1
- [i] bootcmd: run storeboot
- [i] sleep 2 sec Ctrl+C for break boot
- bootm 0x6000000 - 0x1000000
- CONFIG_AVB2:
- avb2: 0
- ee_gate_off ...
- avb2: 0
- ## Booting kernel from Legacy Image at 06000000 ...
- Image Name: kernel
- Image Type: AArch64 Linux Kernel Image (gzip compressed)
- Data Size: 6323555 Bytes = 6 MiB
- Load Address: 01080000
- Entry Point: 01080000
- Verifying Checksum ... OK
- Start read misc partition datas!
- Cannot find dev.
- amlmmc cmd <NULL> failed
- store - STORE sub-system
- Usage:
- store init flag
- store read name addr off|partition size
- read 'size' bytes starting at offset 'off'
- to/from memory address 'addr', skipping bad blocks.
- store write name addr off|partition size
- write 'size' bytes starting at offset 'off'
- to/from memory address 'addr', skipping bad blocks.
- store rom_write add off size.
- write uboot to the boot device
- store erase boot/data:
- erase the area which is uboot or data
- store erase partition <partition_name>:
- erase the area which partition in u-boot
- store erase dtb
- store erase key
- store disprotect key
- store rom_protect on/off
- store scrub off|partition size
- scrub the area from offset and size
- store dtb iread/read/write addr <size>
- read/write dtb, size is optional
- store key read/write addr <size>
- read/write key, size is optional
- store ddr_parameter read/write addr <size>
- read/write ddr parameter, size is optional
- store mbr addr
- update mbr/partition table by dtb
- [burnup]Err:store_read_ops,L84:cmd failed, ret=1, [store read misc 0xb3e85380 0x0 0x820]
- failed to store read misc.
- info->magic =
- info->version_major = 0
- info->version_minor = 0
- info->slots[0].priority = 0
- info->slots[0].tries_remaining = 0
- info->slots[0].successful_boot = 0
- info->slots[1].priority = 0
- info->slots[1].tries_remaining = 0
- info->slots[1].successful_boot = 0
- info->crc32 = 0
- Magic is incorrect.
- boot-info is invalid. Resetting.
- save boot-info
- info->magic =
- info->version_major = 1
- info->version_minor = 0
- info->slots[0].priority = 15
- info->slots[0].tries_remaining = 7
- info->slots[0].successful_boot = 0
- info->slots[1].priority = 14
- info->slots[1].tries_remaining = 7
- info->slots[1].successful_boot = 0
- info->crc32 = -1075449479
- Cannot find dev.
- amlmmc cmd <NULL> failed
- store - STORE sub-system
- Usage:
- store init flag
- store read name addr off|partition size
- read 'size' bytes starting at offset 'off'
- to/from memory address 'addr', skipping bad blocks.
- store write name addr off|partition size
- write 'size' bytes starting at offset 'off'
- to/from memory address 'addr', skipping bad blocks.
- store rom_write add off size.
- write uboot to the boot device
- store erase boot/data:
- erase the area which is uboot or data
- store erase partition <partition_name>:
- erase the area which partition in u-boot
- store erase dtb
- store erase key
- store disprotect key
- store rom_protect on/off
- store scrub off|partition size
- scrub the area from offset and size
- store dtb iread/read/write addr <size>
- read/write dtb, size is optional
- store key read/write addr <size>
- read/write key, size is optional
- store ddr_parameter read/write addr <size>
- read/write ddr parameter, size is optional
- store mbr addr
- update mbr/partition table by dtb
- [burnup]Err:store_write_ops,L148:cmd [store write misc 0xb3e85380 0x0 0x820] failed active slot = 0
- active_slot is normal
- get partition info failed !!
- amlmmc - AMLMMC sub system
- Usage:
- amlmmc read <partition_name> ram_addr addr_byte# cnt_byte
- amlmmc write <partition_name> ram_addr addr_byte# cnt_byte
- amlmmc erase <partition_name> addr_byte# cnt_byte
- amlmmc erase <partition_name>/<device num>
- amlmmc rescan <device_num>
- amlmmc part <device_num> - show partition infomation of mmc
- amlmmc list - lists available devices
- amlmmc env - display env partition offset
- amlmmc switch <device_num> <part name> - part name : boot0, boot1, user
- amlmmc status <device_num> - read sd/emmc device status
- amlmmc ext_csd <device_num> <byte> - read sd/emmc device EXT_CSD [byte]
- amlmmc ext_csd <device_num> <byte> <value> - write sd/emmc device EXT_CSD [byte] value
- amlmmc response <device_num> - read sd/emmc last command response
- amlmmc controller <device_num> - read sd/emmc controller register
- amlmmc write_protect <partition_name> <write_protect_type>
- - set write protect on partition through power_on or temporary
- amlmmc write_protect <addr_base16> <cnt_base10> <write_protect_type>
- - set write protect on specified address through power_on or temporary
- amlmmc send_wp_status <partition_name> send protect status of partition
- amlmmc send_wp_status <addr_base16> <cnt_base10> send protect status on specified address
- amlmmc send_wp_type <partition_name> send protect type of partition
- amlmmc send_wp_type <addr_base16> <cnt_base10> send protect type on specified address
- amlmmc clear_wp <partition_name> clear write protect of partition
- amlmmc clear_wp <addr_base16> <cnt_base10> clear write protect on specified addresst
- amlmmc ds <dev_num> <val> set driver strength
- amlmmc key - disprotect key partition
- amlmmc cmd <NULL> failed
- store - STORE sub-system
- Usage:
- store init flag
- store read name addr off|partition size
- read 'size' bytes starting at offset 'off'
- to/from memory address 'addr', skipping bad blocks.
- store write name addr off|partition size
- write 'size' bytes starting at offset 'off'
- to/from memory address 'addr', skipping bad blocks.
- store rom_write add off size.
- write uboot to the boot device
- store erase boot/data:
- erase the area which is uboot or data
- store erase partition <partition_name>:
- erase the area which partition in u-boot
- store erase dtb
- store erase key
- store disprotect key
- store rom_protect on/off
- store scrub off|partition size
- scrub the area from offset and size
- store dtb iread/read/write addr <size>
- read/write dtb, size is optional
- store key read/write addr <size>
- read/write key, size is optional
- store ddr_parameter read/write addr <size>
- read/write ddr parameter, size is optional
- store mbr addr
- update mbr/partition table by dtb
- No dtbo patitions found
- load dtb from 0x1000000 ......
- ## Flattened Device Tree blob at 01000000
- Booting using the fdt blob at 0x1000000
- No valid dtbo image found
- Uncompressing Kernel Image ... OK
- kernel loaded at 0x01080000, end = 0x01d8a008
- libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND
- [rsvmem] fdt get prop fail.
- Loading Device Tree to 000000001fff6000, end 000000001ffffebd ... OK
- fdt_instaboot: no instaboot image
- Starting kernel ...
- uboot time: 57533461 us
- [ 0.377875] meson8b-dwmac c9410000.ethernet: IRQ eth_wake_irq not found
- [ 0.378851] meson8b-dwmac c9410000.ethernet: IRQ eth_lpi not found
- [ 0.714579] dwc3 c9000000.usb: Failed to get clk 'ref': -2
- [ 0.716976] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
- domain-0 init dvfs: 4
- domain-1 init dvfs: 4
- [ 5.475389] blk_update_request: I/O error, dev loop0, sector 0 op 0x3:(DISCARD) flags 0x800 phys_seg 1 prio class 0
- BusyBox v1.28.4 () built-in shell (ash)
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- -----------------------------------------------------
- [i] BUILD: OPENWRT 18.06.4 v0.5 VIM2 Mon Jan 13 20:46:54 UTC 2020
- [i] POST_CONFIG: booted=emmc hwver=VIM2.V12 script=sd:*.sh
- [i] BOOTINFO: uptime: 7.21 sec, bootup: 7.21
- === WARNING! =====================================
- There is no root password defined on this device!
- Use the passwd command to set up a new password
- in order to prevent unauthorized SSH logins.
- --------------------------------------------------
- [i] LAN_IP: 172.23.0.1 WAN_IP: MDNS:
- WEB : http://172.23.0.1
- root@openwrt-vim:/#
Add Comment
Please, Sign In to add comment