EnGenius ECB9500 bootlog

U-Boot 1.1.3 (Nov 20 2008 - 18:00:37)

Board: RT2880 DRAM:  32 MB
relocate_code Pointer at: 8bfa8000

 twe0 set to <NULL>

 toe0 set to <NULL>

 Default FLASH_CS1_CFG = 0511FFA1

 Ready Set Value = 0x0511FFA1

 Setup FLASH_CS1_CFG = 0511FFA1
 CAS 3 (D1835272)

 EN_ID_29LV640HCOMMA Size = 00800000 bytes

 Set info->start[0]=BC000000

 AMD Read ModeCOMMA flash resetCOMMAtriger at BC000000
flash_protect ON: from 0xBC400000 to 0xBC42522F
protect on 64
protect on 65
protect on 66

  monitor protection ON by defaultCOMMAmonitor_flash_len = 152112

 ENV protection ON by default !!
 flash_protect ON: from 0xBC430000 to 0xBC43FFFF
protect on 67
 D-CACHE set to 4 way
 I-CACHE set to 4 way

 ##### The CPU freq = 266 MHZ ####

 SDRAM bus set to 32 bit
 SDRAM size =32 Mbytes

 Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   5: Load ucos code to SDRAM via TFTP.

   You choosed 3

'8''8''8' 0

3: System Boot system code via Flash.
## Booting image at bc450000 ...
   Image Name:   Linux Kernel Image
   Created:      2010-07-19   1:48:39 UTC

 System Control Status = 0x02910084
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1030015 Bytes = 1005.9 kB
   Load Address: 8a000000
   Entry Point:  8a196040
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
   No initrd
## Transferring control to Linux (at address 8a196040) ...
## Giving linux memsize in MBCOMMA 32

Starting kernel ...


THIS IS ASIC - VERSION B
ramsize = 32 MBytes
rambase not setCOMMA set to default (0x08000000)
MEMORY DESCRIPTOR dump:
[0COMMA8a275ca0]: base<0a000000> size<02000000> type<Free RAM memory>
PROC INIT OK!
init started: BusyBox v1.7.5 (2010-07-19 09:47:32 CST)
starting pid 10COMMA tty '/dev/console': '/sbin/config_init'
Config Init version: 2.2.7.445 date: 2010/07/19
starting pid 55COMMA tty '/dev/ttyS1': '/sbin/config_term'
************************************************************************
*                                  ECB9500                             *
************************************************************************

KernelApp/Ramdisk Ver:2.2.7.445\t\t\t Date:2010/07/19
console> sh: cannot create /lib/modules/2.4.30/modules.dep: Read-only file system
ln: /sbin/./apps_init: File exists
ln: /sbin/./httpsd: File exists
sh: cannot create /proc/switch/power_status: nonexistent directory
sh: cannot create /proc/switch/power_status: nonexistent directory
sh: cannot create /proc/netpktconfig/config_interface: nonexistent directory
sh: cannot create /proc/netpktconfig/config_interface: nonexistent directory