Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-54-generic] (local build)
- Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Model Family: Western Digital RE Serial ATA
- Device Model: WDC WD2500YS-01SHB1
- Serial Number: WD-WCANY4199326
- LU WWN Device Id: 5 0014ee 1ab7accff
- Firmware Version: 20.06C06
- User Capacity: 251.000.193.024 bytes [251 GB]
- Sector Size: 512 bytes logical/physical
- Device is: In smartctl database [for details use: -P show]
- ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
- Local Time is: Sun Apr 26 05:47:54 2020 CEST
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: FAILED!
- Drive failure expected in less than 24 hours. SAVE ALL DATA.
- See vendor-specific Attribute list for failed Attributes.
- General SMART Values:
- Offline data collection status: (0x84) Offline data collection activity
- was suspended by an interrupting command from host.
- Auto Offline Data Collection: Enabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 8400) seconds.
- Offline data collection
- capabilities: (0x7b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: ( 98) minutes.
- Conveyance self-test routine
- recommended polling time: ( 6) minutes.
- SCT capabilities: (0x103f) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 4
- 3 Spin_Up_Time 0x0003 186 184 021 Pre-fail Always - 5675
- 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1233
- 5 Reallocated_Sector_Ct 0x0033 104 104 140 Pre-fail Always FAILING_NOW 764
- 7 Seek_Error_Rate 0x000f 194 192 051 Pre-fail Always - 252
- 9 Power_On_Hours 0x0032 074 074 000 Old_age Always - 19085
- 10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
- 11 Calibration_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
- 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1233
- 194 Temperature_Celsius 0x0022 127 100 000 Old_age Always - 23
- 196 Reallocated_Event_Count 0x0032 110 110 000 Old_age Always - 90
- 197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
- 198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
- 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 1
- 200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0
- SMART Error Log Version: 1
- ATA Error Count: 6 (device log contains only the most recent five errors)
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 6 occurred at disk power-on lifetime: 19081 hours (795 days + 1 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 04 61 f0 70 0b 6b e0 Device Fault; Error: ABRT 240 sectors at LBA = 0x006b0b70 = 7015280
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 35 00 f0 70 0b 6b 19 00 03:41:57.980 WRITE DMA EXT
- e5 00 00 00 00 00 00 00 03:41:50.567 CHECK POWER MODE
- e5 00 00 00 00 00 00 00 03:41:42.397 CHECK POWER MODE
- e5 00 00 00 00 00 00 00 03:41:34.226 CHECK POWER MODE
- 35 00 f0 70 0b 6b 19 00 03:41:26.311 WRITE DMA EXT
- Error 5 occurred at disk power-on lifetime: 19081 hours (795 days + 1 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 04 61 f0 70 0b 6b e0 Device Fault; Error: ABRT 240 sectors at LBA = 0x006b0b70 = 7015280
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 35 00 f0 70 0b 6b 19 00 03:41:26.311 WRITE DMA EXT
- 35 00 f0 80 0a 6b 19 00 03:41:14.536 WRITE DMA EXT
- 35 00 f0 90 09 6b 19 00 03:41:14.532 WRITE DMA EXT
- e5 00 00 00 00 00 00 00 03:41:14.532 CHECK POWER MODE
- 35 00 f0 a0 08 6b 19 00 03:41:02.693 WRITE DMA EXT
- Error 4 occurred at disk power-on lifetime: 19077 hours (794 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 80 60 f0 66 e0 Error: UNC 128 sectors at LBA = 0x0066f060 = 6746208
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 80 60 f0 66 00 00 00:14:00.230 READ DMA EXT
- 25 00 80 e0 ef 66 00 00 00:14:00.227 READ DMA EXT
- 25 00 80 60 ef 66 00 00 00:14:00.224 READ DMA EXT
- 25 00 80 e0 ee 66 00 00 00:14:00.222 READ DMA EXT
- 25 00 80 60 ee 66 00 00 00:14:00.219 READ DMA EXT
- Error 3 occurred at disk power-on lifetime: 19077 hours (794 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 80 60 f0 66 e0 Error: UNC 128 sectors at LBA = 0x0066f060 = 6746208
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 80 60 f0 66 00 00 00:13:44.396 READ DMA EXT
- e5 00 00 00 00 00 00 00 00:13:42.549 CHECK POWER MODE
- e5 00 00 00 00 00 00 00 00:13:34.379 CHECK POWER MODE
- e5 00 00 00 00 00 00 00 00:13:26.208 CHECK POWER MODE
- e5 00 00 00 00 00 00 00 00:13:18.038 CHECK POWER MODE
- Error 2 occurred at disk power-on lifetime: 19077 hours (794 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 51 80 60 f0 66 e0 Error: UNC 128 sectors at LBA = 0x0066f060 = 6746208
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 25 00 80 60 f0 66 00 00 00:09:27.598 READ DMA EXT
- 25 00 80 e0 ef 66 00 00 00:09:27.596 READ DMA EXT
- 25 00 80 60 ef 66 00 00 00:09:27.593 READ DMA EXT
- 25 00 80 e0 ee 66 00 00 00:09:27.590 READ DMA EXT
- 25 00 80 60 ee 66 00 00 00:09:27.588 READ DMA EXT
- SMART Self-test log structure revision number 1
- Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
- # 1 Short offline Completed: read failure 90% 19078 6746210
- # 2 Extended offline Completed: read failure 90% 19078 6746210
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement