API tools faq
paste
Advertisement
Guest User

Untitled

a guest
Jul 6th, 2022
648
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 31.47 KB | None | 0 0
raw download clone embed print report
  1. U-Boot 1.1.3 (Nov 11 2021 - 19:30:41)
  2.  
  3. Board: Ralink APSoC DRAM: 128 MB
  4. relocate_code Pointer at: 87f94000
  5.  
  6. Config XHCI 40M PLL
  7. ***************************
  8. hardware power up
  9. ***************************
  10. Allocate 16 byte aligned buffer: 87fc8530
  11. Enable NFI Clock
  12. # MTK NAND # : Use HW ECC
  13. NAND ID [01 F1 80 1D 01]
  14. Device found in MTK table, ID: 1f1, EXT_ID: 801d01
  15. Support this Device in MTK table! 1f1
  16. select_chip
  17. [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
  18. Signature matched and data read!
  19. load_fact_bbt success 1023
  20. load fact bbt success
  21. [mtk_nand] probe successfully!
  22. mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
  23. [U]: in env check
  24. ...============================================
  25. Ralink UBoot Version: 5.0.0.0
  26. --------------------------------------------
  27. ASIC MT7621A DualCore (MAC to MT7530 Mode)
  28. DRAM_CONF_FROM: Auto-Detection
  29. DRAM_TYPE: DDR3
  30. DRAM bus: 16 bit
  31. Xtal Mode=3 OCP Ratio=1/4
  32. Flash component: NAND Flash
  33. Date:Nov 11 2021 Time:19:30:41
  34. ============================================
  35. icache: sets:256, ways:4, linesz:32 ,total:32768
  36. dcache: sets:256, ways:4, linesz:32 ,total:32768
  37.  
  38. ##### The CPU freq = 880 MHZ ####
  39. estimate memory size =128 Mbytes
  40. #Reset_MT7530
  41. set LAN/WAN LLLLW
  42. [u]ofs = 0x00000000
  43. [u]size = 0x00000000
  44. REG: MEMO2 value = 0x00000000
  45.  
  46. Please choose the operation:
  47. 1: Load system code to SDRAM via TFTP.
  48. 2: Load system code then write to Flash via TFTP.
  49. 3: Boot system code via Flash (default).
  50. 4: Entr boot command line interface.
  51. 7: Load Boot Loader code then write to Flash via Serial.
  52. 9: Load Boot Loader code then write to Flash via TFTP.
  53. default: 3
  54.  
  55. You choosed 1
  56. 0
  57. skip detect restore key
  58. BootType = 1
  59.  
  60.  
  61. 1: System Load Linux to SDRAM via TFTP.
  62. Please Input new ones /or Ctrl-C to discard
  63. Input device IP (10.10.10.123) ==:10.10.10.123
  64. Input server IP (10.10.10.3) ==:10.10.10.3
  65. Input Linux Kernel filename () ==:kernel.bin
  66.  
  67. NetLoop,call eth_halt !
  68.  
  69. NetLoop,call eth_init !
  70. Trying Eth0 (10/100-M)
  71.  
  72. Waitting for RX_DMA_BUSY status Start... done
  73.  
  74.  
  75. ETH_STATE_ACTIVE!!
  76. TFTP from server 10.10.10.3; our IP address is 10.10.10.123
  77. Filename 'kernel.bin'.
  78.  
  79. TIMEOUT_COUNT=10,Load address: 0x84000000
  80. Loading: T T T T T T T checksum bad
  81. checksum bad
  82. T Got ARP REPLY, set server/gtwy eth addr (00:1c:25:70:7f:94)
  83. Got it
  84. Got ARP REQUEST, return our IP
  85. T T
  86. Retry count exceeded; starting again
  87. TFTP from server 10.10.10.3; our IP address is 10.10.10.123
  88. Filename 'kernel.bin'.
  89.  
  90. TIMEOUT_COUNT=10,Load address: 0x84000000
  91. Loading: Got ARP REPLY, set server/gtwy eth addr (00:1c:25:70:7f:94)
  92. Got it
  93. checksum bad
  94. T T T T checksum bad
  95. T Got ARP REQUEST, return our IP
  96. #################################################################
  97. #################################################################
  98. #################################################################
  99. #################################################checksum bad
  100. ################
  101. #################################################################
  102. #################################################################
  103. #################################################################
  104. #################################################################
  105. #################################################################
  106. #################################################################
  107. #################################################################
  108. #################################################################
  109. #################################################################
  110. #################################################################
  111. #################################################################
  112. #################################################################
  113. #################################################################
  114. #################################################################
  115. #################################################################
  116. #################################################################
  117. #################################################################
  118. ############################
  119. done
  120. Bytes transferred = 7128797 (6cc6dd hex)
  121. LoadAddr=84000000 NetBootFileXferSize= 006cc6dd
  122. ..Erasing NAND Flash...
  123. ranand_erase: start:80000, len:20000
  124. .Writing to NAND Flash...
  125. done
  126. Automatic boot of image at addr 0x84000000 ...
  127. ## Booting image at 84000000 ...
  128. Image Name: MIPS OpenWrt Linux-5.10.127
  129. Image Type: MIPS Linux Kernel Image (lzma compressed)
  130. Data Size: 7128733 Bytes = 6.8 MB
  131. Load Address: 80001000
  132. Entry Point: 80001000
  133. Verifying Checksum ... OK
  134. Uncompressing Kernel Image ... OK
  135. No initrd
  136. ## Transferring control to Linux (at address 80001000) ...
  137. ## Giving linux memsize in MB, 128
  138.  
  139. Starting kernel ...
  140.  
  141. [ 0.000000] Linux version 5.10.127 (ianp@t61) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r19989-24eee4b244) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sat Jul 2 14:59:38 2022
  142. [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
  143. [ 0.000000] printk: bootconsole [early0] enabled
  144. [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
  145. [ 0.000000] MIPS: machine is Notion R281
  146. [ 0.000000] Initrd not found or empty - disabling initrd
  147. [ 0.000000] VPE topology {2,2} total 4
  148. [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
  149. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  150. [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  151. [ 0.000000] Zone ranges:
  152. [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
  153. [ 0.000000] HighMem empty
  154. [ 0.000000] Movable zone start for each node
  155. [ 0.000000] Early memory node ranges
  156. [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
  157. [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
  158. [ 0.000000] percpu: Embedded 15 pages/cpu s30224 r8192 d23024 u61440
  159. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
  160. [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
  161. [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
  162. [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
  163. [ 0.000000] Writing ErrCtl register=00050481
  164. [ 0.000000] Readback ErrCtl register=00050481
  165. [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
  166. [ 0.000000] Memory: 115068K/131072K available (6716K kernel code, 621K rwdata, 1360K rodata, 5500K init, 235K bss, 16004K reserved, 0K cma-reserved, 0K highmem)
  167. [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  168. [ 0.000000] rcu: Hierarchical RCU implementation.
  169. [ 0.000000] Tracing variant of Tasks RCU enabled.
  170. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
  171. [ 0.000000] NR_IRQS: 256
  172. [ 0.000000] CPU Clock: 880MHz
  173. [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
  174. [ 0.000013] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
  175. [ 0.015847] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
  176. [ 0.033806] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
  177. [ 0.106133] pid_max: default: 32768 minimum: 301
  178. [ 0.115451] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
  179. [ 0.129855] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
  180. [ 0.148235] rcu: Hierarchical SRCU implementation.
  181. [ 0.158062] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
  182. [ 0.173652] smp: Bringing up secondary CPUs ...
  183. [ 0.183405] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
  184. [ 0.183416] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  185. [ 0.183429] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  186. [ 0.183509] CPU1 revision is: 0001992f (MIPS 1004Kc)
  187. [ 0.243469] Synchronize counters for CPU 1: done.
  188. [ 0.305565] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
  189. [ 0.305574] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  190. [ 0.305582] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  191. [ 0.305629] CPU2 revision is: 0001992f (MIPS 1004Kc)
  192. [ 0.364546] Synchronize counters for CPU 2: done.
  193. [ 0.424922] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
  194. [ 0.424930] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  195. [ 0.424938] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  196. [ 0.424989] CPU3 revision is: 0001992f (MIPS 1004Kc)
  197. [ 0.484129] Synchronize counters for CPU 3: done.
  198. [ 0.543746] smp: Brought up 1 node, 4 CPUs
  199. [ 0.556014] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  200. [ 0.575538] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
  201. [ 0.589373] pinctrl core: initialized pinctrl subsystem
  202. [ 0.602160] NET: Registered protocol family 16
  203. [ 0.613691] cpuidle: using governor teo
  204. [ 0.665368] clocksource: Switched to clocksource GIC
  205. [ 0.677277] NET: Registered protocol family 2
  206. [ 0.686305] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
  207. [ 0.701409] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
  208. [ 0.718008] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
  209. [ 0.733125] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
  210. [ 0.747120] TCP: Hash tables configured (established 1024 bind 1024)
  211. [ 0.759861] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
  212. [ 0.772748] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
  213. [ 0.786847] NET: Registered protocol family 1
  214. [ 0.795411] PCI: CLS 0 bytes, default 32
  215. [ 5.969347] workingset: timestamp_bits=14 max_order=15 bucket_order=1
  216. [ 5.986364] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  217. [ 5.997846] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  218. [ 6.019798] mt7621_gpio 1e000600.gpio: registering 32 gpios
  219. [ 6.031164] mt7621_gpio 1e000600.gpio: registering 32 gpios
  220. [ 6.042528] mt7621_gpio 1e000600.gpio: registering 32 gpios
  221. [ 6.054534] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
  222. [ 6.068933] printk: console [ttyS0] disabled
  223. [ 6.077463] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
  224. [ 6.095380] printk: console [ttyS0] enabled
  225. [ 6.095380] printk: console [ttyS0] enabled
  226. [ 6.111922] printk: bootconsole [early0] disabled
  227. [ 6.111922] printk: bootconsole [early0] disabled
  228. [ 6.133451] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
  229. [ 6.146205] nand: AMD/Spansion S34ML01G2
  230. [ 6.154001] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
  231. [ 6.169089] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
  232. [ 6.182191] 6 fixed-partitions partitions found on MTD device mt7621-nand
  233. [ 6.195711] Creating 6 MTD partitions on "mt7621-nand":
  234. [ 6.206124] 0x000000000000-0x000000080000 : "bootloader"
  235. [ 6.225964] 0x000000080000-0x0000000a0000 : "config"
  236. [ 6.239061] 0x000000100000-0x000000140000 : "factory"
  237. [ 6.254341] 0x000000140000-0x000000540000 : "kernel"
  238. [ 6.330808] 0x000000540000-0x000007f00000 : "ubi"
  239. [ 8.328643] 0x000007f00000-0x000007f80000 : "configbak"
  240. [ 8.396792] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
  241. [ 8.413610] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
  242. [ 8.431615] i2c /dev entries driver
  243. [ 8.441263] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
  244. [ 8.454674] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
  245. [ 8.472204] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
  246. [ 8.488527] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
  247. [ 8.504928] mt7621-pci 1e140000.pcie: Parsing DT failed
  248. [ 8.517463] NET: Registered protocol family 10
  249. [ 8.528095] Segment Routing with IPv6
  250. [ 8.535548] NET: Registered protocol family 17
  251. [ 8.544840] 8021q: 802.1Q VLAN Support v1.8
  252. [ 8.556777] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
  253. [ 8.671748] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=26)
  254. [ 8.693866] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=27)
  255. [ 8.716215] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=28)
  256. [ 8.738458] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=29)
  257. [ 8.761487] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
  258. [ 8.778338] DSA: tree 0 setup
  259. [ 8.784637] rt2880-pinmux pinctrl: pcie is already enabled
  260. [ 8.795676] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
  261. [ 8.809038] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
  262. [ 8.826566] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
  263. [ 8.842860] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
  264. [ 8.859264] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
  265. [ 8.874445] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
  266. [ 8.889512] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22
  267. [ 9.004100] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
  268. [ 9.015225] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
  269. [ 9.126482] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
  270. [ 9.140350] mt7621-pci 1e140000.pcie: PCIE0 enabled
  271. [ 9.150060] mt7621-pci 1e140000.pcie: PCIE1 enabled
  272. [ 9.159772] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
  273. [ 9.178494] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
  274. [ 9.191183] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
  275. [ 9.204881] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
  276. [ 9.218581] pci_bus 0000:00: root bus resource [bus 00-ff]
  277. [ 9.229510] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff])
  278. [ 9.249836] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
  279. [ 9.261819] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
  280. [ 9.274302] pci 0000:00:00.0: reg 0x14: initial BAR value 0x00000000 invalid
  281. [ 9.288342] pci 0000:00:00.0: reg 0x14: [mem size 0x00010000]
  282. [ 9.299868] pci 0000:00:00.0: supports D1
  283. [ 9.307864] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
  284. [ 9.319826] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
  285. [ 9.331838] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
  286. [ 9.344324] pci 0000:00:01.0: reg 0x14: initial BAR value 0x00000000 invalid
  287. [ 9.358365] pci 0000:00:01.0: reg 0x14: [mem size 0x00010000]
  288. [ 9.369885] pci 0000:00:01.0: supports D1
  289. [ 9.377869] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
  290. [ 9.390679] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  291. [ 9.406648] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  292. [ 9.422869] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000
  293. [ 9.434893] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
  294. [ 9.448943] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000]
  295. [ 9.460521] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
  296. [ 9.474001] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
  297. [ 9.484436] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
  298. [ 9.496593] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
  299. [ 9.510112] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff pref]
  300. [ 9.524493] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
  301. [ 9.537966] pci 0000:02:00.0: [14c3:7663] type 00 class 0x000280
  302. [ 9.549993] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid
  303. [ 9.564044] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000 64bit pref]
  304. [ 9.577410] pci 0000:02:00.0: reg 0x18: initial BAR value 0x00000000 invalid
  305. [ 9.591443] pci 0000:02:00.0: reg 0x18: [mem size 0x00004000 64bit pref]
  306. [ 9.604795] pci 0000:02:00.0: reg 0x20: initial BAR value 0x00000000 invalid
  307. [ 9.618840] pci 0000:02:00.0: reg 0x20: [mem size 0x00001000 64bit pref]
  308. [ 9.632303] pci 0000:02:00.0: supports D1 D2
  309. [ 9.640810] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
  310. [ 9.654018] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
  311. [ 9.684971] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
  312. [ 9.695412] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
  313. [ 9.707548] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff]
  314. [ 9.721068] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff pref]
  315. [ 9.735465] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
  316. [ 9.748693] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
  317. [ 9.761863] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
  318. [ 9.775736] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
  319. [ 9.788905] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
  320. [ 9.802777] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
  321. [ 9.816303] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
  322. [ 9.830685] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
  323. [ 9.844209] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x604fffff pref]
  324. [ 9.858602] pci 0000:00:00.0: BAR 1: assigned [mem 0x60500000-0x6050ffff]
  325. [ 9.872130] pci 0000:00:01.0: BAR 1: assigned [mem 0x60510000-0x6051ffff]
  326. [ 9.885653] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
  327. [ 9.899176] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
  328. [ 9.912702] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
  329. [ 9.926238] pci 0000:00:00.0: PCI bridge to [bus 01]
  330. [ 9.936127] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
  331. [ 9.949643] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
  332. [ 9.963163] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
  333. [ 9.977558] pci 0000:02:00.0: BAR 0: assigned [mem 0x60300000-0x603fffff 64bit pref]
  334. [ 9.993004] pci 0000:02:00.0: BAR 2: assigned [mem 0x60400000-0x60403fff 64bit pref]
  335. [ 10.008438] pci 0000:02:00.0: BAR 4: assigned [mem 0x60404000-0x60404fff 64bit pref]
  336. [ 10.023870] pci 0000:00:01.0: PCI bridge to [bus 02]
  337. [ 10.033758] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
  338. [ 10.047291] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
  339. [ 10.060808] pci 0000:00:01.0: bridge window [mem 0x60300000-0x604fffff pref]
  340. [ 10.079866] UBI error: no valid UBI magic found inside mtd4
  341. [ 10.091730] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
  342. [ 10.129019] Freeing unused kernel memory: 5500K
  343. [ 10.138083] This architecture does not have kernel memory protection.
  344. [ 10.150924] Run /init as init process
  345. [ 10.703275] init: Console is alive
  346. [ 10.710466] init: - watchdog -
  347. [ 10.734157] kmodloader: loading kernel modules from /etc/modules-boot.d/*
  348. [ 10.761744] usbcore: registered new interface driver usbfs
  349. [ 10.772873] usbcore: registered new interface driver hub
  350. [ 10.783669] usbcore: registered new device driver usb
  351. [ 10.803692] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator
  352. [ 10.818724] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator
  353. [ 10.834078] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
  354. [ 10.844720] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
  355. [ 10.865296] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010
  356. [ 10.883646] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
  357. [ 10.896539] hub 1-0:1.0: USB hub found
  358. [ 10.904169] hub 1-0:1.0: 2 ports detected
  359. [ 10.912959] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
  360. [ 10.923620] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
  361. [ 10.938591] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
  362. [ 10.951524] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
  363. [ 10.968720] hub 2-0:1.0: USB hub found
  364. [ 10.976387] hub 2-0:1.0: 1 port detected
  365. [ 10.992012] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
  366. [ 11.015575] init: - preinit -
  367. [ 11.221198] random: jshn: uninitialized urandom read (4 bytes read)
  368. [ 11.305771] random: jshn: uninitialized urandom read (4 bytes read)
  369. [ 11.352639] random: jshn: uninitialized urandom read (4 bytes read)
  370. [ 11.615298] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
  371. [ 11.632095] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
  372. [ 11.632106] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
  373. [ 11.662505] 8021q: adding VLAN 0 to HW filter on device lan1
  374. [ 11.676455] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  375. Press the [f] key and hit [enter] to enter failsafe mode
  376. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  377. [ 13.835717] procd: - early -
  378. [ 13.841699] procd: - watchdog -
  379. [ 14.405396] procd: - watchdog -
  380. [ 14.412593] procd: - ubus -
  381. [ 14.425857] random: ubusd: uninitialized urandom read (4 bytes read)
  382. [ 14.475909] random: ubusd: uninitialized urandom read (4 bytes read)
  383. [ 14.489199] random: ubusd: uninitialized urandom read (4 bytes read)
  384. [ 14.505966] procd: - init -
  385. Please press Enter to activate this console.
  386. [ 14.894634] kmodloader: loading kernel modules from /etc/modules.d/*
  387. [ 15.082020] urngd: v1.0.2 started.
  388. [ 15.097791] usbcore: registered new interface driver cdc_acm
  389. [ 15.109134] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  390. [ 15.126836] usbcore: registered new interface driver cdc_wdm
  391. [ 15.139278] Loading modules backported from Linux version v5.15.33-0-g06f50ca83ace
  392. [ 15.154393] Backport generated by backports.git v5.15.33-1-0-g183c4ab2
  393. [ 15.188937] usbcore: registered new interface driver usbserial_generic
  394. [ 15.202294] usbserial: USB Serial support registered for generic
  395. [ 15.216175] usbcore: registered new interface driver cdc_ether
  396. [ 15.230272] usbcore: registered new interface driver cdc_ncm
  397. [ 15.259977] usbcore: registered new interface driver huawei_cdc_ncm
  398. [ 15.294919] random: crng init done
  399. [ 15.301892] random: 32 urandom warning(s) missed due to ratelimiting
  400. [ 15.326261] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=22
  401. [ 15.337106] pci 0000:00:00.0: enabling device (0004 -> 0007)
  402. [ 15.348399] mt7603e 0000:01:00.0: enabling device (0000 -> 0002)
  403. [ 15.360550] mt7603e 0000:01:00.0: ASIC revision: 76030010
  404. [ 16.396103] mt7603e 0000:01:00.0: Firmware Version: ap_pcie
  405. [ 16.407280] mt7603e 0000:01:00.0: Build Time: 20160107100755
  406. [ 16.455133] mt7603e 0000:01:00.0: firmware init done
  407. [ 16.629192] ------------[ cut here ]------------
  408. [ 16.638534] WARNING: CPU: 1 PID: 701 at backports-5.15.33-1/net/wireless/core.c:882 wiphy_register+0xd08/0xd10 [cfg80211]
  409. [ 16.660346] Modules linked in: mt7603e(+) mt76_connac_lib mt76 mac80211 huawei_cdc_ncm cfg80211 cdc_ncm cdc_ether usbserial usbnet slhc nfnetlink nf_reject_ipv6 nf_reject_ipv4 nf_log_ipv6 nf_log_ipv4 nf_log_common nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c hwmon crc_ccitt compat cdc_wdm cdc_acm sha256_generic libsha256 seqiv jitterentropy_rng drbg hmac cmac leds_gpio xhci_plat_hcd xhci_pci xhci_mtk xhci_hcd gpio_button_hotplug usbcore nls_base usb_common mii crc32c_generic
  410. [ 16.743404] CPU: 1 PID: 701 Comm: kmodloader Not tainted 5.10.127 #0
  411. [ 16.756038] Stack : 80e00000 00000001 00000005 80083414 80870000 80764ffc 00000000 00000000
  412. [ 16.772682] 82f63a3c 80de0000 807339d0 81cf32c8 807fae27 00000001 82f639e0 55c9ec8a
  413. [ 16.789325] 00000000 00000000 807339d0 82f63880 ffffefff 00000000 ffffffea 00000000
  414. [ 16.805968] 82f6388c 00000116 80800820 ffffffff 80000000 00000001 00000000 80730000
  415. [ 16.822610] 00000009 8217a834 8217a838 00000001 00000018 803f34f0 00000004 80de0004
  416. [ 16.839252] ...
  417. [ 16.844113] Call Trace:
  418. [ 16.848994] [<800080e0>] show_stack+0x30/0x100
  419. [ 16.857859] [<80371a44>] dump_stack+0x9c/0xcc
  420. [ 16.866546] [<8002ff28>] __warn+0xc0/0x12c
  421. [ 16.874687] [<8002fff0>] warn_slowpath_fmt+0x5c/0xac
  422. [ 16.884587] [<81e812dc>] wiphy_register+0xd08/0xd10 [cfg80211]
  423. [ 16.896343] [<82101508>] ieee80211_register_hw+0x9ac/0xd74 [mac80211]
  424. [ 16.909208] [<81ee41f8>] mt76_register_device+0x320/0x618 [mt76]
  425. [ 16.921195] [<82b02920>] mt7603_register_device+0x9c4/0xb98 [mt7603e]
  426. [ 16.934026] [<82b00168>] init_module+0xc36168/0xc373a0 [mt7603e]
  427. [ 16.945980]
  428. [ 16.949048] ---[ end trace 9e9562d7d174d492 ]---
  429. [ 16.959776] mt7603e: probe of 0000:01:00.0 failed with error -22
  430. [ 16.979186] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=23
  431. [ 16.990020] pci 0000:00:01.0: enabling device (0004 -> 0007)
  432. [ 17.001312] mt7615e 0000:02:00.0: enabling device (0000 -> 0002)
  433. [ 38.025075] rcu: INFO: rcu_sched self-detected stall on CPU
  434. [ 38.036202] rcu: 1-....: (1 GPs behind) idle=fa2/1/0x40000002 softirq=592/593 fqs=1050
  435. [ 38.052293] (t=2102 jiffies g=-531 q=25)
  436. [ 38.060263] NMI backtrace for cpu 1
  437. [ 38.067200] CPU: 1 PID: 701 Comm: kmodloader Tainted: G W 5.10.127 #0
  438. [ 38.082598] Stack : 80e00000 807f82f8 80800000 80083414 80870000 80764ffc 00000000 00000000
  439. [ 38.099245] 8140dd1c 80de0000 807339d0 81cf32c8 807fae27 00000001 8140dcc0 55c9ec8a
  440. [ 38.115888] 00000000 00000000 807339d0 8140db60 ffffefff 00000000 ffffffea 00000000
  441. [ 38.132530] 8140db6c 00000131 80800820 ffffffff 80000000 00000000 00000000 80730000
  442. [ 38.149173] 00000000 80800000 80800000 807f82f8 00000018 803f34f0 00000004 80de0004
  443. [ 38.165815] ...
  444. [ 38.170676] Call Trace:
  445. [ 38.175560] [<800080e0>] show_stack+0x30/0x100
  446. [ 38.184419] [<80371a44>] dump_stack+0x9c/0xcc
  447. [ 38.193093] [<80378554>] nmi_cpu_backtrace+0x104/0x164
  448. [ 38.203313] [<80378708>] nmi_trigger_cpumask_backtrace+0x154/0x184
  449. [ 38.215614] [<8009628c>] rcu_dump_cpu_stacks+0x128/0x17c
  450. [ 38.226187] [<8009c640>] rcu_sched_clock_irq+0x7bc/0x9a4
  451. [ 38.236752] [<800a28c8>] update_process_times+0x78/0xc4
  452. [ 38.247153] [<800b7130>] tick_handle_periodic+0x34/0xd0
  453. [ 38.257550] [<804a800c>] gic_compare_interrupt+0x7c/0x9c
  454. [ 38.268126] [<8008c2bc>] handle_percpu_devid_irq+0xbc/0x19c
  455. [ 38.279234] [<80085d18>] generic_handle_irq+0x44/0x5c
  456. [ 38.289291] [<8038d780>] gic_handle_local_int+0x94/0x118
  457. [ 38.299857] [<8038d814>] gic_irq_dispatch+0x10/0x20
  458. [ 38.309559] [<80085d18>] generic_handle_irq+0x44/0x5c
  459. [ 38.319609] [<8068ef8c>] do_IRQ+0x1c/0x2c
  460. [ 38.327582] [<8038cfb4>] plat_irq_dispatch+0x68/0xf0
  461. [ 38.337459] [<80003508>] except_vec_vi_end+0xb8/0xc4
  462. [ 38.347354] [<8068cdd4>] down_write+0x1c/0x54
  463. [ 38.356046] [<804a6560>] led_trigger_register+0x108/0x1c0
  464. [ 38.366930] [<8215bab4>] ieee80211_led_init+0x3c/0x180 [mac80211]
  465. [ 38.379107] [<821011d8>] ieee80211_register_hw+0x67c/0xd74 [mac80211]
  466. [ 38.391970] [<81ee41f8>] mt76_register_device+0x320/0x618 [mt76]
  467. [ 38.403941] [<821b855c>] mt7615_register_device+0x158/0x230 [mt7615e]
  468. [ 38.416762] [<821ba4d4>] mt7615_mmio_probe+0x208/0x244 [mt7615e]
  469. [ 38.428727] [<803b3728>] pci_device_probe+0xbc/0x150
  470. [ 38.438609] [<80403e68>] really_probe+0x108/0x4d8
  471. [ 38.447966] [<80404990>] device_driver_attach+0x124/0x134
  472. [ 38.458705] [<80404a1c>] __driver_attach+0x7c/0x13c
  473. [ 38.468406] [<80401898>] bus_for_each_dev+0x68/0xa4
  474. [ 38.478107] [<804030ac>] bus_add_driver+0x150/0x238
  475. [ 38.487810] [<80405208>] driver_register+0x98/0x154
  476. [ 38.497513] [<80001644>] do_one_initcall+0x50/0x1a8
  477. [ 38.507216] [<800c37c8>] do_init_module+0x48/0x1f4
  478. [ 38.516745] [<800c606c>] sys_init_module+0x150/0x18c
  479. [ 38.526630] [<80014578>] syscall_common+0x34/0x58
  480. [ 38.535985]
  481. [ 101.055069] rcu: INFO: rcu_sched self-detected stall on CPU
  482. [ 101.066192] rcu: 1-....: (1 GPs behind) idle=fa2/1/0x40000002 softirq=592/593 fqs=4178
  483. [ 101.082285] (t=8405 jiffies g=-531 q=225)
  484. [ 101.090429] NMI backtrace for cpu 1
  485. [ 101.097367] CPU: 1 PID: 701 Comm: kmodloader Tainted: G W 5.10.127 #0
  486. [ 101.112765] Stack : 80e00000 807f82f8 80800000 80083414 80870000 80764ffc 00000000 00000000
  487. [ 101.129412] 8140dd1c 80de0000 807339d0 81cf32c8 807fae27 00000001 8140dcc0 55c9ec8a
  488. [ 101.146055] 00000000 00000000 807339d0 8140db60 ffffefff 00000000 ffffffea 00000000
  489. [ 101.162696] 8140db6c 00000161 80800820 ffffffff 80000000 00000000 00000000 80730000
  490. [ 101.179338] 00000000 80800000 80800000 807f82f8 00000018 803f34f0 00000004 80de0004
  491. [ 101.195981] ...
  492. [ 101.200843] Call Trace:
  493. [ 101.205727] [<800080e0>] show_stack+0x30/0x100
  494. [ 101.214586] [<80371a44>] dump_stack+0x9c/0xcc
  495. [ 101.223260] [<80378554>] nmi_cpu_backtrace+0x104/0x164
  496. [ 101.233480] [<80378708>] nmi_trigger_cpumask_backtrace+0x154/0x184
  497. [ 101.245778] [<8009628c>] rcu_dump_cpu_stacks+0x128/0x17c
  498. [ 101.256353] [<8009c640>] rcu_sched_clock_irq+0x7bc/0x9a4
  499. [ 101.266920] [<800a28c8>] update_process_times+0x78/0xc4
  500. [ 101.277322] [<800b7130>] tick_handle_periodic+0x34/0xd0
  501. [ 101.287719] [<804a800c>] gic_compare_interrupt+0x7c/0x9c
  502. [ 101.298307] [<8008c2bc>] handle_percpu_devid_irq+0xbc/0x19c
  503. [ 101.309431] [<80085d18>] generic_handle_irq+0x44/0x5c
  504. [ 101.319490] [<8038d780>] gic_handle_local_int+0x94/0x118
  505. [ 101.330056] [<8038d814>] gic_irq_dispatch+0x10/0x20
  506. [ 101.339769] [<80085d18>] generic_handle_irq+0x44/0x5c
  507. [ 101.349972] [<8068ef8c>] do_IRQ+0x1c/0x2c
  508. [ 101.357947] [<8038cfb4>] plat_irq_dispatch+0x68/0xf0
  509. [ 101.367823] [<80003508>] except_vec_vi_end+0xb8/0xc4
  510. [ 101.377698] [<8007c8c8>] up_write+0x28/0xb8
  511. [ 101.386164] [<8215bab4>] ieee80211_led_init+0x3c/0x180 [mac80211]
  512. [ 101.398341] [<821011d8>] ieee80211_register_hw+0x67c/0xd74 [mac80211]
  513. [ 101.411204] [<81ee41f8>] mt76_register_device+0x320/0x618 [mt76]
  514. [ 101.423174] [<821b855c>] mt7615_register_device+0x158/0x230 [mt7615e]
  515. [ 101.435994] [<821ba4d4>] mt7615_mmio_probe+0x208/0x244 [mt7615e]
  516. [ 101.447961] [<803b3728>] pci_device_probe+0xbc/0x150
  517. [ 101.457842] [<80403e68>] really_probe+0x108/0x4d8
  518. [ 101.467200] [<80404990>] device_driver_attach+0x124/0x134
  519. [ 101.477937] [<80404a1c>] __driver_attach+0x7c/0x13c
  520. [ 101.487640] [<80401898>] bus_for_each_dev+0x68/0xa4
  521. [ 101.497341] [<804030ac>] bus_add_driver+0x150/0x238
  522. [ 101.507043] [<80405208>] driver_register+0x98/0x154
  523. [ 101.516746] [<80001644>] do_one_initcall+0x50/0x1a8
  524. [ 101.526451] [<800c37c8>] do_init_module+0x48/0x1f4
  525. [ 101.535980] [<800c606c>] sys_init_module+0x150/0x18c
  526. [ 101.545864] [<80014578>] syscall_common+0x34/0x58
  527. [ 101.555219]
  528.  
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!