Guest User

Untitled

a guest
Mar 25th, 2021
53
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. # For more options and information see
  2. # http://rpf.io/configtxt
  3. # Some settings may impact device functionality. See link above for details
  4.  
  5. # uncomment if you get no picture on HDMI for a default "safe" mode
  6. #hdmi_safe=1
  7.  
  8. # uncomment this if your display has a black border of unused pixels visible
  9. # and your display can output without overscan
  10. #disable_overscan=0
  11.  
  12. # uncomment the following to adjust overscan. Use positive numbers if console
  13. # goes off screen, and negative if there is too much border
  14. #overscan_left=16
  15. #overscan_right=16
  16. #overscan_top=16
  17. #overscan_bottom=16
  18.  
  19. # uncomment to force a console size. By default it will be display's size minus
  20. # overscan.
  21. #framebuffer_width=1280
  22. #framebuffer_height=720
  23.  
  24. # uncomment if hdmi display is not detected and composite is being output
  25. #hdmi_force_hotplug=1
  26.  
  27. # uncomment to force a specific HDMI mode (this will force VGA)
  28. hdmi_group=1
  29. #hdmi_mode=16 is 1024x768 60Hz 4:3
  30. hdmi_mode=16
  31. hdmi_ignore_cec=1
  32.  
  33. # uncomment to force a HDMI mode rather than DVI. This can make audio work in
  34. # DMT (computer monitor) modes
  35. #hdmi_drive=2
  36.  
  37. # uncomment to increase signal to HDMI, if you have interference, blanking, or
  38. # no display
  39. config_hdmi_boost=7
  40.  
  41. #enables ignoring of EDID/Display data
  42. hdmi_ignore_edid=0xa5000080
  43.  
  44. # uncomment for composite PAL
  45. #sdtv_mode=2
  46.  
  47. #uncomment to overclock the arm. 700 MHz is the default.
  48. arm_freq=800
  49.  
  50. # Uncomment some or all of these to enable the optional hardware interfaces
  51. #dtparam=i2c_arm=on
  52. #dtparam=i2s=on
  53. #dtparam=spi=on
  54.  
  55. # Uncomment this to enable infrared communication.
  56. #dtoverlay=gpio-ir,gpio_pin=17
  57. #dtoverlay=gpio-ir-tx,gpio_pin=18
  58.  
  59. # Additional overlays and parameters are documented /boot/overlays/README
  60.  
  61. # Enable audio (loads snd_bcm2835)
  62. dtparam=audio=on
  63.  
  64. [pi4]
  65. # Enable DRM VC4 V3D driver on top of the dispmanx display stack
  66. #dtoverlay=vc4-fkms-v3d
  67. max_framebuffers=2
  68.  
  69. [all]
  70. #dtoverlay=vc4-fkms-v3d
  71. gpu_mem_256=128
  72. gpu_mem_512=256
  73. gpu_mem_1024=256
  74. overscan_scale=1
  75. core_freq=250
  76. sdram_freq=400
  77. over_voltage=0
  78. [all]
  79. #dtoverlay=vc4-kms-v3d
  80.  
RAW Paste Data