[2019-11-18 10:22:00] [Output] :  [English] Dion Winters says: Let's start on this beast.
[2019-11-18 10:22:15] [Output] : ⭐ Dion Winters walks towards the desk then notices the packages near it.
[2019-11-18 10:22:33] [Output] : ⭐ Dion Winters extends right arm towards the injectors package then grabs it as he heads towards the evo.
[2019-11-18 10:22:56] [Output] : ⭐ Dion Winters places the package on the roof of the car in a safe location then reaches for his pocket.
[2019-11-18 10:23:16] [Output] : ⭐ Dion Winters would grab the evo x key then would twists it in the door lock to unlock it.
[2019-11-18 10:23:32] [Output] : ⭐ Dion Winters would extends right arm towards the door bar then would opens the door as he slides hisself-
[2019-11-18 10:23:54] [Output] : ⭐ -inside the car,then reaches for the hood releaser then releases the hood as he steps off-      ((Dion Winters))
[2019-11-18 10:24:59] [Output] : ⭐ -the car then heads towards the hood as he inserts right fingers under the hood-      ((Dion Winters))
[2019-11-18 10:25:16] [Output] : ⭐ -then pulls it open and stables it using the metal bar.      ((Dion Winters))
[2019-11-18 10:26:00] [Output] : ⭐ Engine bay would be visible now.      ((Dion Winters))
[2019-11-18 10:26:25] [Output] : ⭐ Dion Winters walks back towards the drive seat then reaches for the turnk releaser then presses it.
[2019-11-18 10:26:42] [Output] : ⭐ the trunk sound should be heared now, Dion would make his way towards it.      ((Dion Winters))
[2019-11-18 10:27:04] [Output] : ⭐ Dion Winters gently pulls the trunk up then starts inspecting the empty trunk.
[2019-11-18 10:27:11] [Output] : ⭐ 'there would be a black box'.      ((Dion Winters))
[2019-11-18 10:27:26] [Output] : ⭐ Dion Winters presses the two clips then removes the black cover, nowthe battery should be visible.
[2019-11-18 10:27:57] [Output] : ⭐ Dion Winters gently and carefully removes the red connector, now the battery should be disconnected.
[2019-11-18 10:28:22] [Output] : ⭐ Dion Would make his way towards the machanic tool kit then would wheels it towards-      ((Dion Winters))
[2019-11-18 10:29:36] [Output] : ⭐ -the hood, then would open the top shelf,then would grabs a 10mm socket and the impact gun.      ((Dion Winters))
[2019-11-18 10:30:11] [Output] : ⭐ Dion Winters leaves the impact gun on the tool kit then extends right arm towards the oil cap on the -
[2019-11-18 10:30:38] [Output] : ⭐ -engine then would turn it to the left several times so that it should be removed.      ((Dion Winters))
[2019-11-18 10:31:04] [Output] : ⭐ Dion Winters would then places it in a safe location then would use both arms to remove the enginecover.
[2019-11-18 10:31:25] [Output] : ⭐ Dion Winters then would reaches for a rag or a paper then places it on the oil cap to prevent anything -
[2019-11-18 10:31:35] [Output] : ⭐ -from falling inside.      ((Dion Winters))
[2019-11-18 10:32:16] [Output] : ⭐ Dion Winters grabs the 10mm impact gun then places itonto one of the 2 10mmbolts holding the crossover -
[2019-11-18 10:32:40] [Output] : ⭐ -tube to the fuel rail, then would start to unbolt them one by one.      ((Dion Winters))
[2019-11-18 10:33:04] [Output] : ⭐ Dion Winters would place the bolts in a safe location on the tool kit then would use the impact gun to -
[2019-11-18 10:33:18] [Output] : ⭐ -loosen the bolt holding it to the manifold.      ((Dion Winters))
[2019-11-18 10:35:26] [Output] : ⭐ Dion Winters would remove the bolt then would places it on the mechanic tool kit.
[2019-11-18 10:35:57] [Output] : ⭐ Dion Winters reaches for the pliers tool then uses it to loosen the hose clamp to unhook the breatherline
[2019-11-18 10:36:08] [Output] : ⭐ -from the valve cover.      ((Dion Winters))
[2019-11-18 10:36:26] [Output] : ⭐ Dion Winters reaches for the 12mm socket then begins to install it onto the impact gun then places the gu
[2019-11-18 10:36:50] [Output] : ⭐ -onto one of the 2 12mm bolts holding the fuel rail in place, then starts to loosen them.      ((Dion Winters))
[2019-11-18 10:37:15] [Output] : ⭐ Dion Winters would places the bolts in a safe location then carefully takes out the spacers and puts them
[2019-11-18 10:37:52] [Output] : ⭐ -in safe location, now Dion should be able to disconnect the injector wiring from each fuel-      ((Dion Winters))
[2019-11-18 10:38:19] [Output] : ⭐ -injector by pressing down on the realease tab and gently pulling on the connector to remove      ((Dion Winters))
[2019-11-18 10:39:01] [Output] : ⭐ it from the injector.      ((Dion Winters))
[2019-11-18 10:39:31] [Output] : ⭐ now with the injectors unplugged, Dion pulls up softly on the rail andd carefully pulls the-      ((Dion Winters))
[2019-11-18 10:39:51] [Output] : ⭐ -injectors out one at a time.      ((Dion Winters))
[2019-11-18 10:40:11] [Output] : ⭐ Dion Winters walks towards the roof then grabs the injector package then opens it and grabs the 4 -
[2019-11-18 10:40:43] [Output] : ⭐ -injectors as he heads back towards the hood, then begins to install them back into the rail      ((Dion Winters))
[2019-11-18 10:40:54] [Output] : ⭐ Dion Winters would make sure not to tear any of the orings.
[2019-11-18 10:41:18] [Output] : ⭐ once all the injectors arein place, Dion carefully pushues the fuel rail down to seat the      ((Dion Winters))
[2019-11-18 10:41:39] [Output] : ⭐ -injectors in the manfild, then makes surethey're all in place properly.      ((Dion Winters))
[2019-11-18 10:42:06] [Output] : ⭐ Dion Winters attaches the injector adapter harnesses then plugs in all the injectors one by one.
[2019-11-18 10:45:56] [Output] : ⭐ Dion Winters reaches for the 12mm bolts then grabs them as he starts to place them in place to hold the -
[2019-11-18 10:46:21] [Output] : ⭐ -fuel railin place then uses the impact gun to tighten them at the very end then hooks the-      ((Dion Winters))
[2019-11-18 10:46:49] [Output] : ⭐ -breather line from the valve cover using pliers to tighten the hose clamp.      ((Dion Winters))
[2019-11-18 10:47:08] [Output] : ⭐ Dion Winters then reaches  the 2 10mm bolts then starts placing them in place to hold the crossover-
[2019-11-18 10:47:41] [Output] : ⭐ -tube to the fuel rail and the additional bolt holding it to the manifold,would tighten it-      ((Dion Winters))
[2019-11-18 10:47:49] [Output] : ⭐ -using the impact gun with 10mm socket.      ((Dion Winters))
[2019-11-18 10:48:41] [Output] : ⭐ Dion Winters would reach for the oil  cap then would twist it in it location after removing the rag that-
[2019-11-18 10:48:56] [Output] : ⭐ -covers the oil area.      ((Dion Winters))
[2019-11-18 10:49:07] [Output] :  [English] Dion Winters says: Injectors done, let's start with the big boys now.
[2019-11-18 11:20:49] [Output] : ⭐ Dion Winters walks towards the lift remote, 'there would be a dashboard there', presses the up button-
[2019-11-18 11:21:28] [Output] : ⭐ -using right finger to fully lift the evo of the ground, then starts walking under it trying      ((Dion Winters))
[2019-11-18 11:21:49] [Output] : ⭐ -to locate the plastic engine corrpartment covers.      ((Dion Winters))
[2019-11-18 11:22:24] [Output] : ⭐ Dion Winters reaches for the plastic clips located in the mechanic tool kit then grabs them as he heads
[2019-11-18 11:22:49] [Output] : ⭐ -towards the evo, then uses them to remove the plastic clips using prying tool.      ((Dion Winters))
[2019-11-18 11:25:44] [Output] : ⭐ Dion Winters would pop out the center section of the clip then pulls it out by hand.
[2019-11-18 11:26:14] [Output] : ⭐ Dion Winters walks towards the passenger side front cover, then reaches for the 10mm impact gun-
[2019-11-18 11:26:30] [Output] : ⭐ -then starts to loosen the 2bolts there one by one then removes the 5plastic clips using-      ((Dion Winters))
[2019-11-18 11:26:49] [Output] : ⭐ -pry tool one by one, making sure they are all removed.      ((Dion Winters))
[2019-11-18 11:27:57] [Output] : ⭐ Dion Winters would remove the passenger side front cover, then would locate the drain valve.
[2019-11-18 11:30:18] [Output] : ⭐ Dion Winters reaches for a bucket lotaced in the bathroom then brings it as he places it under the drain*
[2019-11-18 11:30:53] [Output] : [Notification] Axel is now online!
[2019-11-18 11:31:05] [Output] : ⭐ -valve, then would use 10mm impact to loosen it, 'engine coolant should be filling the -      ((Dion Winters))
[2019-11-18 11:31:17] [Output] : ⭐ -bucket.      ((Dion Winters))
[2019-11-18 11:31:46] [Output] : ⭐ Dion Winters makes his way towards the lift dashboard then presses the down button, as he then-
[2019-11-18 11:32:04] [Output] : ⭐ -walks towards the hood.      ((Dion Winters))
[2019-11-18 11:32:22] [Output] : ⭐ 'there would be no engine cover because it was removed while replacing the injectors'.      ((Dion Winters))
[2019-11-18 11:32:56] [Output] : ⭐ Dion Winters removes the compressor outlet elbow hoses completely with adapter tube between them-
[2019-11-18 11:33:41] [Output] : ⭐ -by removing the 2 hose clamps one by one using the screwdriver.      ((Dion Winters))
[2019-11-18 11:34:00] [Output] : ⭐ Dion Winters would removes the compressor inlet hose, completely with rubber elbow and the bypass valve-
[2019-11-18 11:34:50] [Output] : ⭐ -by removing the, MAF sensor clamp, bypass valve clamp, bypass valve signal line clamp-      ((Dion Winters))
[2019-11-18 11:35:02] [Output] : ⭐ -then turbocharger inlet elbow clamp.      ((Dion Winters))
[2019-11-18 11:35:33] [Output] : ⭐ would try to do so using the philips screwdriver.      ((Dion Winters))
[2019-11-18 11:36:06] [Output] : ⭐ Dion Winters removes the strut tower brace bar using the 14mm impact gun to remove the 3nuts on each side
[2019-11-18 11:36:35] [Output] : ⭐ -then would remove the cowl heat shielf located on the firewall behind the cylinder head-      ((Dion Winters))
[2019-11-18 11:36:59] [Output] : ⭐ - and under the cowl overhang by removing the 3bolts one by one using the 10mm socket.      ((Dion Winters))
[2019-11-18 11:38:03] [Output] : ⭐ Dion Winters removes the heat shield covering the exhaust mainfold and downpipe, by removing the 5bolts-
[2019-11-18 11:38:11] [Output] : ⭐ -using 10mm socket.      ((Dion Winters))
[2019-11-18 11:39:22] [Output] : ⭐ Dion Winters removes the vaccum hose from the black metal compressor outlet elbow and from the wastegate-
[2019-11-18 11:39:55] [Output] : ⭐ -actuator, by removing the 2hose clamps using the screwdriver.      ((Dion Winters))
[2019-11-18 11:40:27] [Output] : ⭐ Dion Winters removes the black metal compressor outlet elbow and its gasket, by removing the 2bolts using
[2019-11-18 11:40:35] [Output] : ⭐ -12mm socket.      ((Dion Winters))
[2019-11-18 11:40:59] [Output] : ⭐ from the driver's side, reaches for the steel bracket then braces the compressor housing to-      ((Dion Winters))
[2019-11-18 11:41:20] [Output] : ⭐ -the engine block, then removes the bracket, by removing the 2 17mm bolts using the wrench.      ((Dion Winters))
[2019-11-18 11:42:02] [Output] : ⭐ Dion Winters  removes the cast aluminum inlet elbow from the compressor housing, along with its gasket,-
[2019-11-18 11:42:21] [Output] : ⭐ -would do so by removing the 3 12mm bolts using the 12mm wrench.      ((Dion Winters))
[2019-11-18 11:42:43] [Output] : ⭐ Dion Winters reaches for the hard steel water line that connects to the rear of the turbocharger's center
[2019-11-18 11:43:08] [Output] : ⭐ -housing then removes it along with its banjo bolt, cooper crush washers, and mounting bolt-      ((Dion Winters))
[2019-11-18 11:43:47] [Output] : ⭐ Dion Winters would disconnect the rubber hose, by removing the 1 clamp and 1banjo bolt and the 10mm -
[2019-11-18 11:43:59] [Output] : ⭐ -ratchet and 17mm ratchet.      ((Dion Winters))
[2019-11-18 11:44:18] [Output] : ⭐ Dion Winters locates the hard steel water line that connects to the front of the turbocharger's-
[2019-11-18 11:44:37] [Output] : ⭐ -center housing, then removes the rubber hose that connects to the hard line-      ((Dion Winters))
[2019-11-18 11:45:08] [Output] : ⭐ -and makes sure to leave the hard line attached to the turbocharger.      ((Dion Winters))
[2019-11-18 11:45:44] [Output] : ⭐ Dion Winters from underneath the vehicle, removes the front exhaust pipe by removing the 2 bolts using 14
[2019-11-18 11:46:13] [Output] : ⭐ -mm ratchet then removes the rear nuts using 19mm ratchet.      ((Dion Winters))
[2019-11-18 11:46:33] [Output] : ⭐ Dion Winters from underneath the vehicle, removes the black steel bracket that connects the turbine -
[2019-11-18 11:46:58] [Output] : ⭐ -outlet elbow to the engine block using 14mm ratchet to remove the 2 bolts.      ((Dion Winters))
[2019-11-18 11:48:16] [Output] : ⭐ Dion Winters from underneath the vehicle, removes the heat shield attached to the top side of the t-
[2019-11-18 11:48:48] [Output] : ⭐ -transfer case, behind and below the turbocharger, using 10mm ratchet to remove the 3bolts.      ((Dion Winters))
[2019-11-18 11:49:13] [Output] : ⭐ Dion Winters removes the heat shield above the passenger side inner drive shaft boot by removing the 2 bo
[2019-11-18 11:49:26] [Output] : ⭐ -bolts of 10mm ratchet.      ((Dion Winters))
[2019-11-18 11:50:25] [Output] : ⭐ Dion Winters from above the turbocharger, locates the large heat shielf that covers the downpipe-
[2019-11-18 11:50:52] [Output] : ⭐ -then removes the 3bolts to free both heat shields using 14mm ratchet.      ((Dion Winters))
[2019-11-18 11:51:23] [Output] : ⭐ Dion Winters removes the downpipe next, by removing the 4 bolts and the one nut securing it to the turbin
[2019-11-18 11:51:50] [Output] : ⭐ e- housing, using 14mm socket to remove the 4bolts one by one.      ((Dion Winters))
[2019-11-18 11:52:12] [Output] : ⭐ Dion Winters reaches for the small steel bracket that connects the turbine housing to the engine block,-
[2019-11-18 11:52:43] [Output] : ⭐ -then removes the bolt into the turbine housing, by removing the 1bolt using the 14mm ratche      ((Dion Winters))
[2019-11-18 11:53:30] [Output] : ⭐ t- then removes the oil feed line from the engine block, by removing the 2bolts using10mm -      ((Dion Winters))
[2019-11-18 11:53:38] [Output] : ⭐ -wrench.      ((Dion Winters))
[2019-11-18 11:54:38] [Output] : ⭐ Dion Winters locates the turbocharger oil drain line, then removes the single bolt securing clamp to -
[2019-11-18 11:55:00] [Output] : ⭐ -engine block, then pulls oil drain line out of block but leaves it attached to the turbo-      ((Dion Winters))
[2019-11-18 11:55:09] [Output] : [NEWS] The lottery was drawn! Number: 68. Jackpot: $42,188
[2019-11-18 11:55:10] [Output] : Payslip
[2019-11-18 11:55:10] [Output] :
[2019-11-18 11:55:10] [Output] :   Bank Interest: $442 (≈2.03%)
[2019-11-18 11:55:10] [Output] :   Property Expenses: $21
[2019-11-18 11:55:10] [Output] :   Gross Income: $421
[2019-11-18 11:55:10] [Output] :   Remark(s): Transferred to your bank account.
[2019-11-18 11:55:10] [Output] :   Your employer did not pay you as you were off duty.
[2019-11-18 11:55:49] [Output] : ⭐ Dion Winters ensures the rubber o-rings is present and did not break and fall into oil pan.
[2019-11-18 11:56:06] [Output] : ⭐ Dion Winters from abovethe turbocharger, removesthe 2bolts and the 2nuts securing the turbine housing*
[2019-11-18 11:57:03] [Output] : Trial Admin Jack Staton has teleported to you.
[2019-11-18 11:57:07] [Output] : Jack Staton: (( oops ))
[2019-11-18 11:57:32] [Output] : ⭐ -to the exhaust manifold.      ((Dion Winters))
[2019-11-18 11:58:16] [Output] : ⭐ Dion Winters removes the 10nuts and washers securing the exhaust manifold to cylinder head then removes-
[2019-11-18 11:58:30] [Output] : ⭐ -exhaust manifold carefully as he places it onto the tool kit.      ((Dion Winters))
[2019-11-18 12:00:08] [Output] : ⭐ Dion Winters pulls the turbocharger up and out of the engine compartment from the top side-
[2019-11-18 12:00:17] [Output] : ⭐ -then places it near the wall.      ((Dion Winters))
[2019-11-18 12:01:17] [Output] : ⭐ Dion Winters walks towards the new turbo package located in the desk room then grabs it as he heads-
[2019-11-18 12:01:28] [Output] : ⭐ -back towards the hood then places it onto the ground.      ((Dion Winters))
[2019-11-18 12:01:51] [Output] : ⭐ Dion Winters opens the package then reaches for the full turbo kit mounted as he the places the exhaust-
[2019-11-18 12:02:23] [Output] : ⭐ -manifold with the turbo onto the cylinder head then secures it using the 5bolts on each sid      ((Dion Winters))
[2019-11-18 12:02:46] [Output] : ⭐ Dion Winters would tightens them using 14mm socket, then from above the turbocharger places the-
[2019-11-18 12:03:22] [Output] : ⭐ -2bolts and the 2nuts securing the turbing housing to the exuast manifold.      ((Dion Winters))
[2019-11-18 12:03:42] [Output] : ⭐ Dion Winters would places back the oil feed line from the engine block using the banjo bolt.
[2019-11-18 12:03:59] [Output] : [Notification] ikbenspy is now online!
[2019-11-18 12:04:01] [Output] : ⭐ Dion Winters reaches for the small stell bracket that connects the turbine housing to the engine block-
[2019-11-18 12:04:16] [Output] : ⭐ -then places the bolt into the turbine housing to places it back.      ((Dion Winters))
[2019-11-18 12:04:42] [Output] : ⭐ Dion Winters places the downpipe to it location using the 4bolts and the 1nut securing it to the turbine*
[2019-11-18 12:05:22] [Output] : ⭐ -housing, then from above the turbocharger, grabs the large heat shield then begins-      ((Dion Winters))
[2019-11-18 12:05:36] [Output] : ⭐ -to secures it using the 3bolts and the 14mm ratchet.      ((Dion Winters))
[2019-11-18 12:06:01] [Output] : ⭐ Dion Winters places the heatshield back above the passenger side inner driveshaft boot using
[2019-11-18 12:06:25] [Output] : ⭐ -2bolts and 10mm ratchet, then from underneath the vehicle places the heat shield back-      ((Dion Winters))
[2019-11-18 12:06:48] [Output] : ⭐ to attach to the top side of the transfer case, behind and below the turbocharger using      ((Dion Winters))
[2019-11-18 12:06:57] [Output] : ⭐ -3bolts and 10mm ratchet.      ((Dion Winters))
[2019-11-18 12:07:38] [Output] : ⭐ Dion Winters from underneath the vehicle places the lack steel bracket that connects the turbine outlet-
[2019-11-18 12:08:40] [Output] : ⭐ Dion Winters from underneath the vehicle places the front exhaust pipe using the 2bolts and the 14mm
[2019-11-18 12:09:04] [Output] : ⭐ -ratchet thenplaces the hard steel water line that connects to the rear of the turbocharger-      ((Dion Winters))
[2019-11-18 12:09:28] [Output] : ⭐ -center housing, along with is banjo bolt, copper crush washer, and mounting bolt.      ((Dion Winters))
[2019-11-18 12:09:54] [Output] : ⭐ Dion Winters places the cast aluminum inlet elbow from the compressor housing, along with its gasket usin
[2019-11-18 12:10:30] [Output] : ⭐ -3bolts and 12mm ratchet, then from the driver's side, places the steel bracket that braces-      ((Dion Winters))
[2019-11-18 12:10:50] [Output] : ⭐ -the compressor housing to the engine block, then places the black metal compressor outlet-      ((Dion Winters))
[2019-11-18 12:11:13] [Output] : ⭐ -elbow and its gasket, using 2bolts and 12mm ratchet.      ((Dion Winters))
[2019-11-18 12:11:34] [Output] : ⭐ Dion Winters places the vaccum hose from the black metal compressor outlet elbow and from the waste
[2019-11-18 12:12:11] [Output] : ⭐ -gate actuator using 2hose clamps then places the heat shield covering the exhaust-      ((Dion Winters))
[2019-11-18 12:12:24] [Output] : ⭐ -manifold and downpipe using the 5bolts and 10mm ratchet.      ((Dion Winters))
[2019-11-18 12:12:50] [Output] : ⭐ Dion Winters places the cowl heat shield back to the firewall behind the cylinder head and under the cowl
[2019-11-18 12:13:09] [Output] : ⭐ -overhang using the 3bolts and the10mm ratchet.      ((Dion Winters))
[2019-11-18 12:13:28] [Output] : ⭐ Dion Winters would place the strut tower brace bar back to it place using the 3nuts on each side-
[2019-11-18 12:13:54] [Output] : ⭐ -and the 14mm ratchet, then would connects the compressor inlet hose complete with rubber*      ((Dion Winters))
[2019-11-18 12:14:16] [Output] : ⭐ -elbow and bypass valve using the 4clamps of the maf sensor, bypass valve, bypass valve-      ((Dion Winters))
[2019-11-18 12:14:44] [Output] : ⭐ -signal line and turbocharger inlet elbow clamp then would places the compressor outlet elbo      ((Dion Winters))
[2019-11-18 12:15:14] [Output] : ⭐ -elbow hoses complete with the adapter tube between them by placing the2hose clamps.      ((Dion Winters))
[2019-11-18 12:15:28] [Output] : ⭐ Dion Winters sighs heavily.
[2019-11-18 12:15:31] [Output] :  [English] Dion Winters says: Damn budd.
[2019-11-18 12:15:35] [Output] :  [English] Dion Winters says: Looks dope.
[2019-11-18 12:15:43] [Output] :  [English] Dion Winters says: Still needs the intercooler fuck i forgot.
[2019-11-18 12:15:58] [Output] : ⭐ Dion Winters reaches down to his radio, grabbing it as he pushes the "PTT" button, speaking into it.
[2019-11-18 12:17:27] [Output] : ⭐ Dion Winters works towards the right vehicle fender wells then removes the 3push type-
[2019-11-18 12:17:51] [Output] : ⭐ retainers and the one m6 bolt from both front fenders wells.      ((Dion Winters))
[2019-11-18 12:18:23] [Output] : ⭐ Dion Winters leans under the car then removes the 18push type retainers one by one from lower valence -
[2019-11-18 12:18:52] [Output] : ⭐ -panel then stands up then heads towards the hood and removes the cold air intake and upper      ((Dion Winters))
[2019-11-18 12:19:13] [Output] : ⭐ -valance panel by removing the 4 m6 bolts and one push retainer from the front end.      ((Dion Winters))
[2019-11-18 12:19:32] [Output] : ⭐ Dion Winters unsaps front end from fender on both sides, then disconnects lighting harness and removes -
[2019-11-18 12:19:56] [Output] : ⭐ -front end, then loosen clamps holding factory couplers to factory I/C inlet and outlet port      ((Dion Winters))
[2019-11-18 12:20:23] [Output] : ⭐ Dion Winters removes the 2 m8 bolts from bottom of factory I/C mounts then removes the 4 M8 bolts holding
[2019-11-18 12:20:39] [Output] : ⭐ -left and right factory i/C mounts to bumper support.      ((Dion Winters))
[2019-11-18 12:21:06] [Output] : ⭐ Dion Winters removes the 1 M8 bolt holding factory I/C pipe to core support on driver's side.
[2019-11-18 12:21:27] [Output] : ⭐ Dion Winters removes factory I/C and removes mounts with grommets from factory.
[2019-11-18 12:21:53] [Output] : ⭐ Dion Winters removes the 1 M6 bolt from hood latch bracket then removes threaded dowel and the 2 grommets
[2019-11-18 12:22:04] [Output] : ⭐ -and spacers from factory I/C.      ((Dion Winters))
[2019-11-18 12:22:40] [Output] : ⭐ Dion Winters installs dowel, grommets and spacers onto the new I/C then slips the factory I/C side mounts
[2019-11-18 12:23:10] [Output] : ⭐ -and grommets onto the new I/C.      ((Dion Winters))
[2019-11-18 12:23:33] [Output] : ⭐ Dion Winters mounts the new I/C to bumper support loosely with 4 facotry M8 bolts and loosely conencts-
[2019-11-18 12:23:53] [Output] : ⭐ -factory couplers and clamps, then slides top I/C mount grommet and spacer so it slips-      ((Dion Winters))
[2019-11-18 12:24:21] [Output] : ⭐ -over factory nut on back side of the hood latch, support thread m6 bolt and m6 washer*t      ((Dion Winters))
[2019-11-18 12:24:36] [Output] : [Notification] Axel has gone offline!
[2019-11-18 12:24:42] [Output] : ⭐ -trough hood latch bracket and I/C grommet spacer and bracket, then secures loosely with-      ((Dion Winters))
[2019-11-18 12:24:52] [Output] : ⭐ - 32mm OD M6 washer and nut.      ((Dion Winters))

[2019-11-18 12:26:44] [Output] : ⭐ Dion Winters grabs the new intercooler as he starts placing it in place then places the 1 M6 bolt holding
[2019-11-18 12:26:52] [Output] : ⭐ -factory I/C pipe to core support on driver's side.      ((Dion Winters))
[2019-11-18 12:27:24] [Output] : ⭐ Dion Winters then places the 4 M8 bolts left & right factory I/C mounts to bumper support, then places
[2019-11-18 12:27:44] [Output] : ⭐ -the m8 bolts from bottom of factory I/C mounts then tighten the clamps holding factory -      ((Dion Winters))
[2019-11-18 12:28:05] [Output] : ⭐ -couplers to factory I/C inlet and outlet ports.      ((Dion Winters))
[2019-11-18 12:28:31] [Output] : ⭐ Dion Winters snaps the front end fender on both sides then connects the lighting harness and places the-
[2019-11-18 12:28:53] [Output] : ⭐ -front end then places the 4 M6 bolts and onepush type retainer from front end.      ((Dion Winters))
[2019-11-18 12:29:14] [Output] : ⭐ Dion Winters places the cold air intake then and upper valance panel then places the 18push type retainer
[2019-11-18 12:29:57] [Output] : ⭐ Dion Winters walks back towards the turnk then located the red connector then conencts it the the battery
[2019-11-18 12:30:10] [Output] : ⭐ -then slides the baterry cover to it original location.      ((Dion Winters))