Guest User

Orange Pi One with lobotis' Ubuntu Mate

a guest
Feb 12th, 2016
301
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. HELLO! BOOT0 is starting!
  2. boot0 version : 4.0.0
  3. fel_flag = 0x00000000
  4. rtc[0] value = 0x00000000
  5. rtc[1] value = 0x00000000
  6. rtc[2] value = 0x00000000
  7. rtc[3] value = 0x00000000
  8. rtc[4] value = 0x00000000
  9. rtc[5] value = 0x00000000
  10. rtc[6] value = 0x00000000
  11. rtc[7] value = 0x00000000
  12. DRAM DRIVE INFO: V0.8
  13. DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
  14. DRAM CLK = 672 MHz
  15. DRAM zq value: 003b3bfb
  16. READ DQS LCDL = 0020201f
  17. DRAM SIZE =512 M
  18. odt delay
  19. dram size =512
  20. card boot number = 0
  21. card no is 0
  22. sdcard 0 line count 4
  23. [mmc]: mmc driver ver 2014-12-10 21:20:39
  24. [mmc]: ***Try SD card 0***
  25. [mmc]: SD/MMC Card: 4bit, capacity: 7580MB
  26. [mmc]: vendor: Man 00035344 Snr 437635a9
  27. [mmc]: product: SL08G
  28. [mmc]: revision: 8.0
  29. [mmc]: ***SD/MMC 0 init OK!!!***
  30. sdcard 0 init ok
  31. The size of uboot is 000dc000.
  32. sum=ede66ee7
  33. src_sum=ede66ee7
  34. Succeed in loading uboot from sdmmc flash.
  35. Ready to disable icache.
  36. Jump to secend Boot.
  37. SUNXI_NORMAL_MODE
  38. [ 0.366]e mode
  39.  
  40. U-Boot 2011.09-rc1 (Jun 21 2015 - 19:33:17) Allwinner Technology
  41.  
  42. [ 0.373]version: 1.1.0
  43. normal mode
  44. [ 0.381]pmbus: ready
  45. not set main pmu id
  46. axp_probe error
  47. sunxi_set_cpux_voltage_by_i2c error
  48. [ 0.399]PMU: pll1 1200 Mhz,PLL6=600 Mhz
  49. AXI=400 Mhz,AHB=200 Mhz, APB1=100 Mhz
  50. sid read already
  51. fel key new mode
  52. run key detect
  53. no key found
  54. no key input
  55. dram_para_set start
  56. dram_para_set end
  57. normal mode
  58. [ 0.429]DRAM: 512 MiB
  59. relocation Offset is: 15af9000
  60. [box standby] read rtc = 0x0
  61. [box_start_os] mag be start_type no use
  62. user_gpio config
  63. user_gpio ok
  64. gic: normal or no secure os mode
  65. workmode = 0
  66. MMC: 0
  67. [ 0.503][mmc]: mmc driver ver 2014-12-10 9:23:00
  68. [ 0.508][mmc]: get sdc_phy_wipe fail.
  69. [ 0.512][mmc]: get sdc0 sdc_erase fail.
  70. [ 0.516][mmc]: get sdc_f_max fail,use default 50000000Hz
  71. [ 0.521][mmc]: get sdc_ex_dly_used fail,use default dly
  72. [ 0.527][mmc]: SUNXI SD/MMC: 0
  73. [ 0.540][mmc]: *Try SD card 0*
  74. [ 0.589][mmc]: CID 0x3534453 0x4c303847 0x80437635 0xa900f78f
  75. [ 0.594][mmc]: mmc clk 50000000
  76. [ 0.598][mmc]: SD/MMC Card: 4bit, capacity: 7580MB
  77. [ 0.602][mmc]: boot0 capacity: 0KB,boot1 capacity: 0KB
  78. [ 0.608][mmc]: ***SD/MMC 0 init OK!!!***
  79. [ 0.612][mmc]: erase_grp_size:0x1WrBlk * 0x200 = 0x200 Byte
  80. [ 0.618][mmc]: secure_feature 0x0
  81. [ 0.621][mmc]: secure_removal_type 0x0
  82. [ 0.625]sunxi flash init ok
  83. script config pll_de to 864 Mhz
  84. Not Found clk pll_video1 in script
  85. script config pll_video to 297 Mhz
  86. [boot]disp_init_tv
  87. [DISP_TV] disp_init_tv enter g_tv_used
  88. screen 0 do not support TV TYPE!
  89. [BOOOT_DISP_TV] disp tv device_registered
  90. unable to find regulator vcc-hdmi-18 from [pmu1_regu] or [pmu2_regu]
  91. enable power vcc-hdmi-18, ret=-1
  92. DRV_DISP_Init end
  93. boot_disp.auto_hpd=1
  94. auto hpd check has 100 times!
  95. auto check no any connected, the output_type is 4
  96. [disk_read_fs] no the partition
  97. error: open disp_rsl.fex, maybe it is not exist
  98. not support this mode[4], use inline mode[4]
  99. attched ok, mgr0<-->device0, type=4, mode=4----
  100. ready to set mode
  101. [ 2.005]finally, output_type=0x4, output_mode=0x4, screen_id=0x0, disp_para=0x0
  102. fail to find part named env
  103. Using default environment
  104.  
  105. In: serial
  106. Out: serial
  107. Err: serial
  108. --------fastboot partitions--------
  109. mbr not exist
  110. base bootcmd=run setargs_mmc boot_normal
  111. bootcmd set setargs_mmc
  112. key 0
  113. cant find rcvy value
  114. cant find fstbt value
  115. no misc partition is found
  116. to be run cmd=run setargs_mmc boot_normal
  117. [ 2.042][mmc]: MMC Device 2 not found
  118. [ 2.046][mmc]: Can not find mmc dev
  119. [ 2.049][mmc]: read first backup failed in fun sdmmc_secure_storage_read line 1849
  120. sunxi_secstorage_read fail
  121. get secure storage map err
  122. the private part isn't exist
  123. WORK_MODE_BOOT
  124. adver not need show
  125. sunxi_bmp_logo_display
  126. [disk_read_fs] no the partition
  127. error: open bootlogo.bmp, maybe it is not exist
  128. sunxi bmp info error : unable to open logo file bootlogo.bmp
  129. [ 2.082]Hit any key to stop autoboot: 0
  130. [ 5.341][mmc]: blkcnt should not be 0
  131. [ 5.812][mmc]: blkcnt should not be 0
  132. ## Booting kernel from Legacy Image at 40007800 ...
  133. Image Name: Linux-3.4.39-01-lobo
  134. Image Type: ARM Linux Kernel Image (uncompressed)
  135. Data Size: 10917536 Bytes = 10.4 MiB
  136. Load Address: 40008000
  137. Entry Point: 40008000
  138. Verifying Checksum ... OK
  139. Loading Kernel Image ... OK
  140. OK
  141. [ 6.005][mmc]: MMC Device 2 not found
  142. [ 6.008][mmc]: mmc not find,so not exit
  143. [ 6.012]
  144. Starting kernel ...
  145.  
  146. [sun8i_fixup]: From boot, get meminfo:
  147. Start: 0x40000000
  148. Size: 512MB
  149. ion_carveout reserve: 160m@0 256m@0 130m@1 200m@1
  150. ion_reserve_common: ion reserve: [0x56000000, 0x60000000]!
  151. [ 0.000000] Booting Linux on physical CPU 0
  152. [ 0.000000] Initializing cgroup subsys cpu
  153. [ 0.000000] Linux version 3.4.39-01-lobo (boris@UbuntuMate) (gcc version 4.6.3 20120201 (prerelease) (crosstool-NG linaro-1.13.1-2012.02-20120222 - L
  154. inaro GCC 2012.02) ) #1 SMP PREEMPT Sun Oct 25 14:46:41 CET 2015
  155. [ 0.000000] Ignoring tag cmdline (using the default kernel command line)
  156. [ 0.000000] bootconsole [earlycon0] enabled
  157. [ 0.000000] cma: CMA: reserved 160 MiB at 56000000
  158. [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
  159. [ 0.000000] On node 0 totalpages: 131072
  160. [ 0.000000] free_area_init_node: node 0, pgdat c1000cc0, node_mem_map c10dd000
  161. [ 0.000000] Normal zone: 1152 pages used for memmap
  162. [ 0.000000] Normal zone: 0 pages reserved
  163. [ 0.000000] Normal zone: 129920 pages, LIFO batch:31
  164. [ 0.000000] script_init enter!
  165. [ 0.000000] script_init exit!
  166. [ 0.000000] PERCPU: Embedded 8 pages/cpu @c156f000 s11840 r8192 d12736 u32768
  167. [ 0.000000] pcpu-alloc: s11840 r8192 d12736 u32768 alloc=8*4096
  168. [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
  169. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920
  170. [ 0.000000] Kernel command line: earlyprintk=ttyS0,115200 loglevel=8 initcall_debug=0 console=ttyS0,115200 console=tty0 init=/init
  171. [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
  172. [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
  173. [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
  174. [ 0.000000] Memory: 512MB = 512MB total
  175. [ 0.000000] Memory: 337392k/337392k available, 186896k reserved, 0K highmem
  176. [ 0.000000] Virtual kernel memory layout:
  177. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  178. [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  179. [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
  180. [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
  181. [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  182. [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  183. [ 0.000000] .text : 0xc0008000 - 0xc09873b4 (9725 kB)
  184. [ 0.000000] .init : 0xc0988000 - 0xc0f87e40 (6144 kB)
  185. [ 0.000000] .data : 0xc0f88000 - 0xc1003738 ( 494 kB)
  186. [ 0.000000] .bss : 0xc1003eec - 0xc10dc400 ( 866 kB)
  187. [ 0.000000] Preemptible hierarchical RCU implementation.
  188. [ 0.000000] Additional per-CPU info printed with stalls.
  189. [ 0.000000] NR_IRQS:544
  190. [ 0.000000] Architected local timer running at 24.00MHz.
  191. [ 0.000000] Switching to timer-based delay loop
  192. [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
  193. [ 0.000000] Console: colour dummy device 80x30
  194. [ 0.000000] console [tty0] enabled, bootconsole disabled
  195. [ 0.000000] Booting Linux on physical CPU 0
  196. [ 0.000000] Initializing cgroup subsys cpu
  197. [ 0.000000] Linux version 3.4.39-01-lobo (boris@UbuntuMate) (gcc version 4.6.3 20120201 (prerelease) (crosstool-NG linaro-1.13.1-2012.02-20120222 - L
  198. inaro GCC 2012.02) ) #1 SMP PREEMPT Sun Oct 25 14:46:41 CET 2015
  199. [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
  200. [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  201. [ 0.000000] Machine: sun8i
  202. [ 0.000000] Ignoring tag cmdline (using the default kernel command line)
  203. [ 0.000000] bootconsole [earlycon0] enabled
  204. [ 0.000000] cma: CMA: reserved 160 MiB at 56000000
  205. [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
  206. [ 0.000000] On node 0 totalpages: 131072
  207. [ 0.000000] free_area_init_node: node 0, pgdat c1000cc0, node_mem_map c10dd000
  208. [ 0.000000] Normal zone: 1152 pages used for memmap
  209. [ 0.000000] Normal zone: 0 pages reserved
  210. <7>[ 0.000000] Normal zone: 129920 pages, LIFO batch:31
  211. [ 0.000000] script_init enter!
  212. [ 0.000000] script_init exit!
  213. [ 0.000000] PERCPU: Embedded 8 pages/cpu @c156f000 s11840 r8192 d12736 u32768
  214. [ 0.000000] pcpu-alloc: s11840 r8192 d12736 u32768 alloc=8*4096
  215. [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
  216. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920
  217. [ 0.000000] Kernel command line: earlyprintk=ttyS0,115200 loglevel=8 initcall_debug=0 console=ttyS0,115200 console=tty0 init=/init
  218. [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
  219. [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
  220. [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
  221. [ 0.000000] Memory: 512MB = 512MB total
  222. [ 0.000000] Memory: 337392k/337392k available, 186896k reserved, 0K highmem
  223. [ 0.000000] Virtual kernel memory layout:
  224. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  225. [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  226. [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
  227. [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
  228. [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  229. [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  230. [ 0.000000] .text : 0xc0008000 - 0xc09873b4 (9725 kB)
  231. [ 0.000000] .init : 0xc0988000 - 0xc0f87e40 (6144 kB)
  232. [ 0.000000] .data : 0xc0f88000 - 0xc1003738 ( 494 kB)
  233. [ 0.000000] .bss : 0xc1003eec - 0xc10dc400 ( 866 kB)
  234. [ 0.000000] Preemptible hierarchical RCU implementation.
  235. [ 0.000000] Additional per-CPU info printed with stalls.
  236. [ 0.000000] NR_IRQS:544
  237. [ 0.000000] Architected local timer running at 24.00MHz.
  238. [ 0.000000] Switching to timer-based delay loop
  239. [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
  240. [ 0.000000] Console: colour dummy device 80x30
  241. [ 0.000000] console [tty0] enabled, bootconsole disabled
  242. [ 0.019903] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
  243. [ 0.019957] pid_max: default: 32768 minimum: 301
  244. [ 0.020232] Mount-cache hash table entries: 512
  245. [ 0.021110] Initializing cgroup subsys cpuacct
  246. [ 0.021137] Initializing cgroup subsys freezer
  247. [ 0.021181] CPU: Testing write buffer coherency: ok
  248. [ 0.021242] ftrace: allocating 26206 entries in 77 pages
  249. [ 0.050264] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
  250. [ 0.050298] [sunxi_smp_prepare_cpus] enter
  251. [ 0.050339] Setting up static identity map for 0x406d3b90 - 0x406d3be8
  252. [ 0.051174] CPU1: Booted secondary processor
  253. [ 0.051174] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
  254. [ 0.051303] CPU2: Booted secondary processor
  255. [ 0.051303] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
  256. [ 0.051303] CPU3: Booted secondary processor
  257. [ 0.051303] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
  258. [ 0.060172] Brought up 4 CPUs
  259. [ 0.060254] SMP: Total of 4 processors activated (19200.00 BogoMIPS).
  260. [ 0.060835] devtmpfs: initialized
  261. [ 0.063149] wakeup src cnt is : 1.
  262. [ 0.063168] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800000
  263. [ 0.063191] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x0
  264. [ 0.063215] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x40
  265. [ 0.063240] sunxi pm init
  266. [ 0.063362] pinctrl core: initialized pinctrl subsystem
  267. [ 0.070758] NET: Registered protocol family 16
  268. [ 0.071391] DMA: preallocated 2048 KiB pool for atomic coherent allocations
  269. [ 0.071391] script_sysfs_init success
  270. [ 0.071391] sunxi_dump_init success
  271. [ 0.072141] gpiochip_add: registered GPIOs 0 to 383 on device: sunxi-pinctrl
  272. [ 0.072141] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
  273. [ 0.072141] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
  274. [ 0.072141] hw-breakpoint: maximum watchpoint size is 8 bytes.
  275. [ 0.072141] script config pll_video to 297 Mhz
  276. [ 0.072141] script config pll_de to 864 Mhz
  277. [ 0.072141] script config pll_ve to 402 Mhz
  278. [ 0.072141] sunxi_default_clk_init
  279. [ 0.072141] try to set pll6ahb1 to 200000000
  280. [ 0.072141] try to set ahb clk source to pll6ahb1
  281. [ 0.072141] set ahb clk source to pll6ahb1
  282. [ 0.072141] try to set ahb1 to 200000000
  283. [ 0.072141] try to set apb1 to 100000000
  284. [ 0.072141] ===fe3o4==== sunxi_root_procfs_attach ret:0
  285. [ 0.080217] bio: create slab <bio-0> at 0
  286. [ 0.080366] [ARISC] :sunxi-arisc driver v1.04
  287. [ 0.091531] [ARISC] :arisc version: [v0.1.34]
  288. [ 0.173914] [ARISC] :sunxi-arisc driver v1.04 startup succeeded
  289. [ 0.180383] SCSI subsystem initialized
  290. [ 0.180569] usbcore: registered new interface driver usbfs
  291. [ 0.180649] usbcore: registered new interface driver hub
  292. [ 0.180692] usbcore: registered new device driver usb
  293. [ 0.180692] twi_chan_cfg()335 - [twi0] has no twi_regulator.
  294. [ 0.180692] twi_chan_cfg()335 - [twi1] has no twi_regulator.
  295. [ 0.180692] twi_chan_cfg()335 - [twi2] has no twi_regulator.
  296. [ 0.180692] Linux video capture interface: v2.00
  297. [ 0.180700] Advanced Linux Sound Architecture Driver Version 1.0.25.
  298. [ 0.181169] Bluetooth: Core ver 2.16
  299. [ 0.181215] NET: Registered protocol family 31
  300. [ 0.181236] Bluetooth: HCI device and connection manager initialized
  301. [ 0.181262] Bluetooth: HCI socket layer initialized
  302. [ 0.181282] Bluetooth: L2CAP socket layer initialized
  303. [ 0.181321] Bluetooth: SCO socket layer initialized
  304. [ 0.181530] cfg80211: Calling CRDA to update world regulatory domain
  305. [ 0.181610] Switching to clocksource arch_sys_counter
  306. [ 0.191898] FS-Cache: Loaded
  307. [ 0.192173] CacheFiles: Loaded
  308. [ 0.201747] NET: Registered protocol family 2
  309. [ 0.202012] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
  310. [ 0.202495] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
  311. [ 0.202738] TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
  312. [ 0.202957] TCP: Hash tables configured (established 16384 bind 16384)
  313. [ 0.202981] TCP: reno registered
  314. [ 0.203000] UDP hash table entries: 256 (order: 1, 8192 bytes)
  315. [ 0.203034] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  316. [ 0.203309] NET: Registered protocol family 1
  317. [ 0.203649] RPC: Registered named UNIX socket transport module.
  318. [ 0.203676] RPC: Registered udp transport module.
  319. [ 0.203694] RPC: Registered tcp transport module.
  320. [ 0.203712] RPC: Registered tcp NFSv4.1 backchannel transport module.
  321. [ 0.539266] hw perfevents: enabled with ARMv7 Cortex_A7 PMU driver, 5 counters available
  322. [ 0.539411] sunxi_reg_init enter
  323. [ 0.540200] audit: initializing netlink socket (disabled)
  324. [ 0.540257] type=2000 audit(0.540:1): initialized
  325. [ 0.541923] NFS: Registering the id_resolver key type
  326. [ 0.542263] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
  327. [ 0.542906] NTFS driver 2.1.30 [Flags: R/W].
  328. [ 0.543041] fuse init (API version 7.18)
  329. [ 0.543724] Btrfs loaded
  330. [ 0.543756] msgmni has been set to 978
  331. [ 0.544769] io scheduler noop registered
  332. [ 0.544793] io scheduler deadline registered
  333. [ 0.544875] io scheduler cfq registered (default)
  334. [ 0.545294] [DISP]disp_module_init
  335. [ 0.545598] cmdline,disp=
  336. [ 0.551863] [DISP] Fb_map_kernel_logo,line:925:Fb_map_kernel_logo failed!
  337. [ 0.564603] Console: switching to colour frame buffer device 160x45
  338. [ 0.578234] [DISP]disp_module_init finish
  339. [ 0.578522] sw_uart_get_devinfo()1503 - uart0 has no uart_regulator.
  340. [ 0.578929] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
  341. [ 0.579071] sw_uart_pm()890 - uart0 clk is already enable
  342. [ 0.579200] sw_console_setup()1233 - console setup baud 115200 parity n bits 8, flow n
  343. [ 0.675455] console [ttyS0] enabled
  344. [ 1.273432] sunxi_cmatest_init enter
  345. [ 1.436183] sunxi_cmatest_init success
  346. [ 1.591965] loop: module loaded
  347. [ 1.741372] sunxi_spi_chan_cfg()1355 - [spi-0] has no spi_regulator.
  348. [ 1.902021] sunxi_spi_chan_cfg()1355 - [spi-1] has no spi_regulator.
  349. [ 1.965038] tun: Universal TUN/TAP device driver, 1.6
  350. [ 1.974456] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  351. [ 1.985976] PPP generic driver version 2.4.2
  352. [ 1.994772] PPP BSD Compression module registered
  353. [ 2.003883] PPP Deflate Compression module registered
  354. [ 2.015439] PPP MPPE Compression module registered
  355. [ 2.024617] NET: Registered protocol family 24
  356. [ 2.033349] PPTP driver version 0.8.5
  357. [ 2.041418] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  358. [ 2.072562] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  359. [ 2.085338] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1
  360. [ 2.098137] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
  361. [ 2.120029] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
  362. [ 2.130981] hub 1-0:1.0: USB hub found
  363. [ 2.138927] hub 1-0:1.0: 1 port detected
  364. [ 2.167419] sunxi-ehci sunxi-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  365. [ 2.180277] sunxi-ehci sunxi-ehci.2: new USB bus registered, assigned bus number 2
  366. [ 2.193017] sunxi-ehci sunxi-ehci.2: irq 106, io mem 0xf1c1b000
  367. [ 2.220035] sunxi-ehci sunxi-ehci.2: USB 0.0 started, EHCI 1.00
  368. [ 2.230860] hub 2-0:1.0: USB hub found
  369. [ 2.238771] hub 2-0:1.0: 1 port detected
  370. [ 2.247206] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  371. [ 2.277869] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
  372. [ 2.290198] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 3
  373. [ 2.302461] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400
  374. [ 2.374479] hub 3-0:1.0: USB hub found
  375. [ 2.382492] hub 3-0:1.0: 1 port detected
  376. [ 2.410982] sunxi-ohci sunxi-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
  377. [ 2.423488] sunxi-ohci sunxi-ohci.2: new USB bus registered, assigned bus number 4
  378. [ 2.435928] sunxi-ohci sunxi-ohci.2: irq 107, io mem 0xf1c1b400
  379. [ 2.504492] hub 4-0:1.0: USB hub found
  380. [ 2.512667] hub 4-0:1.0: 1 port detected
  381. [ 2.521273] Initializing USB Mass Storage driver...
  382. [ 2.530730] usbcore: registered new interface driver usb-storage
  383. [ 2.541322] USB Mass Storage support registered.
  384. [ 2.550381] usbcore: registered new interface driver ums-alauda
  385. [ 2.560902] usbcore: registered new interface driver ums-cypress
  386. [ 2.571453] usbcore: registered new interface driver ums-datafab
  387. [ 2.581902] usbcore: registered new interface driver ums_eneub6250
  388. [ 2.592446] usbcore: registered new interface driver ums-freecom
  389. [ 2.602776] usbcore: registered new interface driver ums-isd200
  390. [ 2.612997] usbcore: registered new interface driver ums-jumpshot
  391. [ 2.623433] usbcore: registered new interface driver ums-karma
  392. [ 2.633459] usbcore: registered new interface driver ums-onetouch
  393. [ 2.643779] usbcore: registered new interface driver ums-realtek
  394. [ 2.653922] usbcore: registered new interface driver ums-sddr09
  395. [ 2.663895] usbcore: registered new interface driver ums-sddr55
  396. [ 2.673783] usbcore: registered new interface driver ums-usbat
  397. [ 2.683612] usbcore: registered new interface driver usbserial
  398. [ 2.693277] usbserial: USB Serial Driver core
  399. [ 2.701324] usbcore: registered new interface driver option
  400. [ 2.710740] USB Serial support registered for GSM modem (1-port)
  401. [ 2.721083] file system registered
  402. [ 2.729483] android_usb gadget: Mass Storage Function, version: 2009/09/11
  403. [ 2.740368] android_usb gadget: Number of LUNs=3
  404. [ 2.748636] lun0: LUN: removable file: (no medium)
  405. [ 2.757205] lun1: LUN: removable file: (no medium)
  406. [ 2.765724] lun2: LUN: removable file: (no medium)
  407. [ 2.774473] android_usb gadget: android_usb ready
  408. [ 2.782974] uinput result 0 , vmouse_init
  409. [ 2.791139] mousedev: PS/2 mouse device common for all mice
  410. [ 2.800574] sunxikbd_init failed.
  411. [ 2.807332] ls_fetch_sysconfig_para: type err device_used = 0.
  412. [ 2.817074] =========script_get_err============
  413. [ 2.825147] ltr_init: ls_fetch_sysconfig_para err.
  414. [ 2.834013] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0
  415. [ 2.844543] i2c /dev entries driver
  416. [ 2.851695] IR RC5(x) protocol handler initialized
  417. [ 2.860161] sunxi tsc version 0.1
  418. [ 2.866979] tscdev_init: tsc driver is disabled
  419. [ 2.875124] sunxi cedar version 0.1
  420. [ 2.882157] [cedar]: install start!!!
  421. [ 2.889350] [cedar]: install end!!!
  422. [ 2.896152] sunxi_wdt_init_module: sunxi WatchDog Timer Driver v1.0
  423. [ 2.906211] sunxi_wdt_probe: devm_ioremap return wdt_reg 0xf1c20ca0, res->start 0x01c20ca0, res->end 0x01c20cbf
  424. [ 2.917598] sunxi_wdt_probe: initialized (g_timeout=16s, g_nowayout=0)
  425. [ 2.931108] wdt_enable, write reg 0xf1c20cb8 val 0x00000000
  426. [ 2.940458] timeout_to_interv, line 167
  427. [ 2.947818] interv_to_timeout, line 189
  428. [ 2.955135] wdt_set_tmout, write 0x000000b0 to mode reg 0xf1c20cb8, actual timeout 16 sec
  429. [ 2.967749] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
  430. [ 2.980516] Bluetooth: HCI UART driver ver 2.2
  431. [ 2.988834] [cpu_freq] ERR:get cpu extremity frequency from sysconfig failed, use max_freq
  432. [ 3.001794] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.109 2014-12-4 20:51) Compiled in Oct 25 2015 at 14:44:42
  433. [ 3.016945] [mmc]: get mmc0's sdc_power is null!
  434. [ 3.025842] [mmc]: get mmc1's sdc_power is null!
  435. [ 3.034707] [mmc]: get mmc1's 2xmode ok, val = 1
  436. [ 3.043595] [mmc]: get mmc1's ddrmode ok, val = 1
  437. [ 3.052611] [mmc]: MMC host used card: 0x3, boot card: 0x0, io_card 2
  438. [ 3.064584] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  439. [ 3.081687] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  440. [ 3.098294] no blue_led, ignore it!
  441. [ 3.106411] Registered led device: red_led
  442. [ 3.115196] Registered led device: green_led
  443. [ 3.125416] usbcore: registered new interface driver usbhid
  444. [ 3.135704] usbhid: USB HID core driver
  445. [ 3.147405] asoc: sndcodec <-> sunxi-codec mapping ok
  446. [ 3.160122] asoc: sndhdmi <-> sunxi-hdmiaudio.0 mapping ok
  447. [ 3.171066] oprofile: using arm/armv7-ca7
  448. [ 3.179658] u32 classifier
  449. [ 3.186618] Actions configured
  450. [ 3.194393] Netfilter messages via NETLINK v0.30.
  451. [ 3.203762] nf_conntrack version 0.5.0 (7831 buckets, 31324 max)
  452. [ 3.214918] ctnetlink v0.93: registering with nfnetlink.
  453. [ 3.225009] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
  454. [ 3.236937] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
  455. [ 3.247913] xt_time: kernel timezone is -0000
  456. [ 3.257069] IPv4 over IPv4 tunneling driver
  457. [ 3.266251] gre: GRE over IPv4 demultiplexor driver
  458. [ 3.275813] ip_gre: GRE over IPv4 tunneling driver
  459. [ 3.285839] ip_tables: (C) 2000-2006 Netfilter Core Team
  460. [ 3.296023] arp_tables: (C) 2002 David S. Miller
  461. [ 3.305306] TCP: cubic registered
  462. [ 3.313037] Initializing XFRM netlink socket
  463. [ 3.322032] NET: Registered protocol family 10
  464. [ 3.332121] Mobile IPv6
  465. [ 3.338909] ip6_tables: (C) 2000-2006 Netfilter Core Team
  466. [ 3.349251] IPv6 over IPv4 tunneling driver
  467. [ 3.359048] NET: Registered protocol family 17
  468. [ 3.368071] NET: Registered protocol family 15
  469. [ 3.377129] Bluetooth: RFCOMM TTY layer initialized
  470. [ 3.386444] Bluetooth: RFCOMM socket layer initialized
  471. [ 3.395998] Bluetooth: RFCOMM ver 1.11
  472. [ 3.403989] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  473. [ 3.413680] Bluetooth: BNEP filters: protocol multicast
  474. [ 3.423201] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  475. [ 3.433539] L2TP core driver, V2.0
  476. [ 3.440889] PPPoL2TP kernel driver, V2.0
  477. [ 3.448672] L2TP IP encapsulation support (L2TPv3)
  478. [ 3.457433] L2TP netlink interface
  479. [ 3.464635] L2TP ethernet pseudowire support (L2TPv3)
  480. [ 3.473717] Registering the dns_resolver key type
  481. [ 3.482624] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
  482. [ 3.494724] ThumbEE CPU extension supported.
  483. [ 3.502973] Registering SWP/SWPB emulation handler
  484. [ 3.512736] cmdline,disp=
  485. [ 3.519128] [HDMI] power vcc-hdmi-18
  486. [ 3.557340] sunxi-rtc sunxi-rtc: setting system clock to 1970-01-01 02:08:35 UTC (7715)
  487. [ 3.569923] ths_fetch_sysconfig_para: type err device_used = 1.
  488. [ 3.581668] CPU Budget:Register notifier
  489. [ 3.589658] CPU Budget:register Success
  490. [ 3.597507] sunxi-budget-cooling sunxi-budget-cooling: Cooling device registered: thermal-budget-0
  491. [ 3.613946] [rf_pm]: select module num is 7
  492. [ 3.622381] [rf_pm]: module power0 name vcc-wifi-33
  493. [ 3.631564] [rf_pm]: failed to fetch module_power1
  494. [ 3.640640] [rf_pm]: mod has no chip_en gpio
  495. [ 3.649098] [rf_pm]: failed to fetch lpo_use_apclk
  496. [ 3.658116] [rf_pm]: regulator on.
  497. [ 3.665530] [wifi_pm]: no wifi used in configuration
  498. [ 3.674671] ALSA device list:
  499. [ 3.681585] #0: audiocodec
  500. [ 3.688340] #1: sndhdmi
  501. [ 3.694784] Warning: unable to open an initial console.
  502. [ 3.709272] Freeing init memory: 6140K
  503. [ 4.065063] [mmc]: mmc 0 detect change, present 1
  504. [ 4.160082] [DISP] disp_device_attached_and_enable,line:159:attched ok, mgr0<-->device0, type=4, mode=4
  505. [ 4.570108] [mmc]: sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  506. [ 4.588489] [mmc]: sdc0 power_supply is null
  507. [ 4.620072] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  508. [ 4.652397] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
  509. [ 4.668769] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
  510. [ 4.678746] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  511. [ 4.704504] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  512. [ 4.723531] *******************Try sdio*******************
  513. [ 4.735556] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
  514. [ 4.749248] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
  515. [ 4.763044] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
  516. [ 4.776666] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
  517. [ 4.788986] *******************Try sd *******************
  518. [ 4.799912] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  519. [ 4.814642] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  520. [ 4.831655] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  521. [ 4.901534] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
  522. [ 4.922050] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
  523. [ 4.936357] [mmc]: sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
  524. [ 4.950648] [mmc]: sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B
  525. [ 4.964830] mmc0: new high speed SDHC card at address aaaa
  526. [ 4.975194] mmcblk0: mmc0:aaaa SL08G 7.40 GiB
  527. [ 4.985270] mmcblk0: p1 p2
  528. [ 4.992744] *******************sd init ok*******************
  529. [ 10.111346] systemd-udevd[106]: starting version 215
  530. [ 11.262712] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
  531. [ 11.904343] systemd[1]: Failed to insert module 'autofs4'
  532. [ 12.210293] systemd[1]: systemd 219 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT -GNUTL
  533. S +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN)
  534. [ 12.246319] systemd[1]: Detected architecture arm.
  535. [ 12.284803] systemd[1]: Set hostname to <OrangePI>.
  536. [ 12.605089] systemd[1]: Reached target Remote File Systems (Pre).
  537. [ 12.616101] systemd[1]: Starting Remote File Systems (Pre).
  538. [ 12.631127] systemd[1]: Created slice Root Slice.
  539. [ 12.640614] systemd[1]: Starting Root Slice.
  540. [ 12.654386] systemd[1]: Listening on Journal Socket (/dev/log).
  541. [ 12.665293] systemd[1]: Starting Journal Socket (/dev/log).
  542. [ 12.680508] systemd[1]: Listening on Delayed Shutdown Socket.
  543. [ 12.691134] systemd[1]: Starting Delayed Shutdown Socket.
  544. [ 12.705817] systemd[1]: Listening on udev Control Socket.
  545. [ 12.715930] systemd[1]: Starting udev Control Socket.
  546. [ 12.730474] systemd[1]: Listening on Journal Audit Socket.
  547. [ 12.740766] systemd[1]: Starting Journal Audit Socket.
  548. [ 12.755086] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
  549. [ 12.767065] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
  550. [ 12.783569] systemd[1]: Created slice User and Session Slice.
  551. [ 12.794369] systemd[1]: Starting User and Session Slice.
  552. [ 12.809224] systemd[1]: Reached target Swap.
  553. [ 12.818410] systemd[1]: Starting Swap.
  554. [ 12.827129] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
  555. [ 12.840054] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
  556. [ 12.858204] systemd[1]: Listening on fsck to fsckd communication Socket.
  557. [ 12.870322] systemd[1]: Starting fsck to fsckd communication Socket.
  558. [ 12.882091] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
  559. [ 12.902408] systemd[1]: Reached target Encrypted Volumes.
  560. [ 12.913204] systemd[1]: Starting Encrypted Volumes.
  561. [ 12.928444] systemd[1]: Listening on Journal Socket.
  562. [ 12.938526] systemd[1]: Starting Journal Socket.
  563. [ 12.952806] systemd[1]: Created slice System Slice.
  564. [ 12.962588] systemd[1]: Starting System Slice.
  565. [ 12.976780] systemd[1]: Created slice system-serial\x2dgetty.slice.
  566. [ 12.988199] systemd[1]: Starting system-serial\x2dgetty.slice.
  567. [ 13.003993] systemd[1]: Created slice system-getty.slice.
  568. [ 13.014441] systemd[1]: Starting system-getty.slice.
  569. [ 13.120732] systemd[1]: Starting Setup Virtual Console...
  570. [ 13.144490] systemd[1]: Mounted Huge Pages File System.
  571. [ 13.240291] systemd[1]: Mounting Debug File System...
  572. [ 13.320590] systemd[1]: Starting Journal Service...
  573. [ 13.450370] systemd[1]: Starting LSB: Set keymap...
  574. [ 13.474022] systemd[1]: Reached target Slices.
  575. [ 13.484202] systemd[1]: Starting Slices.
  576. [ 13.590526] systemd[1]: Starting Create list of required static device nodes for the current kernel...
  577. [ 13.670540] systemd[1]: Starting Load Kernel Modules...
  578. [ 13.750735] systemd[1]: Starting File System Check on Root Device...
  579. [ 13.777861] systemd[1]: Started Set Up Additional Binary Formats.
  580. [ 13.793334] systemd[1]: Mounted POSIX Message Queue File System.
  581. [ 13.817830] systemd[1]: Listening on udev Kernel Socket.
  582. [ 13.836060] systemd[1]: Starting udev Kernel Socket.
  583. [ 13.920530] systemd[1]: Starting udev Coldplug all Devices...
  584. [ 13.946506] systemd[1]: Mounted Debug File System.
  585. [ 13.963490] systemd[1]: Started Journal Service.
  586. [ 14.631394] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
  587.  
  588. Ubuntu 15.04 OrangePI ttyS0
  589.  
  590. OrangePI login:
RAW Paste Data

Adblocker detected! Please consider disabling it...

We've detected AdBlock Plus or some other adblocking software preventing Pastebin.com from fully loading.

We don't have any obnoxious sound, or popup ads, we actively block these annoying types of ads!

Please add Pastebin.com to your ad blocker whitelist or disable your adblocking software.

×