HELLO! BOOT0 is starting!
boot0 version : 3.1.0
reg_addr 0x01f00100 =0x00000000
reg_addr 0x01f00104 =0x00000000
reg_addr 0x01f00108 =0x00000000
reg_addr 0x01f0010c =0x00000000
reg_addr 0x01f00110 =0x00000000
reg_addr 0x01f00114 =0x00000000
[DRAM]ver 1.06 clk = 408
cpu 1 pmu 1
dram size =1024
sum=0xc0352551
src_sum=0xc0352551
Ready to disable icache.
Jump to secend Boot.
[      0.207]

U-Boot 2011.09-rc1-00000-gfa2c354 (Sep 15 2014 - 09:28:49) Allwinner Technology

[      0.216]version: 1.1.0
[      0.229]pmbus:   ready
[      0.232]PMU: AXP221
[      0.234]PMU: AXP22x found
[      0.237]PMU: bat ratio = 100
[      0.240]PMU: dcdc3 1260
[      0.243]PMU: pll1 1008 Mhz
dcdc1_vol = 3000
dcdc2_vol = 1200
dcdc3_vol = 1260
dcdc4_vol = 1240
dcdc5_vol = 1500
aldo2_vol = 1800
aldo3_vol = 3000
eldo3_vol = 1200
find power_sply to end
fel key old mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
[      0.285]DRAM:  1 GiB
relocation Offset is: 15b12000
donn't initialize ther user_gpio (main_key:boot_init_gpio)
deu_mode1 not exist.
lcdgamma4iep for lcd1 not exist.
DRV_DISP_Init: opened
[      0.572]fetch script data boot_disp.output_type fail
[      0.577]fetch script data boot_disp.output_mode fail
[      0.582]fetch script data boot_disp.auto_hpd fail
[      0.587]lcd0_para.lcd_used=1
workmode = 0
[      0.926]NAND: NAND_UbootInit
NAND_UbootInit start
NB1 : enter NAND_LogicInit
uboot:physical version: 2 19 20140617 1840
nand : get id_number_ctl fail, 1
uboot:nand info: a714dead ffff4a42 31c0 40704 5
not burn nand partition table!
NB1 : nftl num: 2
 init nftl: 0
NB1 : NAND_LogicInit ok, result = 0x0
[      1.638]sunxi flash init ok
probe mmc0 if exist
[mmc]: mmc driver ver 2014-5-26 14:21:30
[mmc]: get sdc_odly_25M fail,use default dly 0
[mmc]: get sdc_sdly_25M fail,use default dly 5
[mmc]: get sdc_odly_50M fail,use default dly 3
[mmc]: get sdc_sdly_50M fail,use default dly 4
[mmc]: get sdc_f_max fail,use default sdc_f_max 52000000
[mmc]: SUNXI SD/MMC: 0
[mmc]: ************Try SD card 0************
[mmc]: MID 000003 PSN c3cc0e1c
[mmc]: PRV 8.0
[mmc]: MDT m-3 y-2017
[mmc]: ---------------mmc->clock 0-----------
[mmc]: ---------------mmc->bus_width 4--------------
[mmc]: SD/MMC Card: 4bit, capacity: 30436MB
[mmc]: boot0 capacity: 0KB,boot1 capacity: 0KB
[mmc]: ************SD/MMC 0 init OK!!!************
boot0 magic = eGON.BT0/©éÌ
set next system status
DRV_DISP_Exit: closed
sunxi_board_close_source
NAND_UbootExit
NB1 : NAND_LogicExit
reset cpu
HELLO! BOOT0 is starting!
boot0 version : 3.1.0
reg_addr 0x01f00100 =0x00007347
reg_addr 0x01f00104 =0x0000703b
reg_addr 0x01f00108 =0x00000000
reg_addr 0x01f0010c =0x000000ff
reg_addr 0x01f00110 =0x000000ff
reg_addr 0x01f00114 =0x000000ff
eraly jump fel

U-Boot SPL 2024.01-rc2-00070-g17e9db18f1 (Nov 26 2023 - 03:27:35 -0300)
DRAM: 1024 MiB
Trying to boot from MMC1


U-Boot 2024.01-rc2-00070-g17e9db18f1 (Nov 26 2023 - 03:27:35 -0300) Allwinner Technology

CPU:   Allwinner A31s (SUN6I)
Model: Yones TopTech BS1078 v2 Tablet
DRAM:  1 GiB
Core:  57 devices, 20 uclasses, devicetree: separate
WDT:   Not starting watchdog@1c20ca0
MMC:   mmc@1c0f000: 0
Loading Environment from FAT... Unable to use mmc 0:1...
EDID block 0: checksum error, retrying
EDID block 0: checksum error, retrying
EDID block 0: checksum error
Setting up a 1280x800 lcd console (overscan 0x0)
In:    serial
Out:   serial,vidconsole
Err:   serial,vidconsole
Net:   No ethernet found.
Hit any key to stop autoboot:  2  1  0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
580 bytes read in 3 ms (188.5 KiB/s)
## Executing script at 43100000
8094208 bytes read in 337 ms (22.9 MiB/s)
36648 bytes read in 26 ms (1.3 MiB/s)
7163492 bytes read in 299 ms (22.8 MiB/s)
Kernel image @ 0x42000000 [ 0x000000 - 0x7b8200 ]
## Flattened Device Tree blob at 43000000
   Booting using the fdt blob at 0x43000000
Working FDT set to 43000000
   Loading Ramdisk to 4992b000, end 49fffe64 ... OK
   Loading Device Tree to 4991f000, end 4992af27 ... OK
Working FDT set to 4991f000

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 6.2.1-1-ARCH (builduser@leming) (armv7l-unknown-linux-gnueabihf-gcc (GCC) 12.1.0, GNU ld (GNU Binutils) 2.38) #1 SMP PREEMPT Sat Feb 25 16:08:15 MST 2023
[    0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Yones TopTech BS1078 v2 Tablet
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 64 MiB at 0x7a000000
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000006fffffff]
[    0.000000]   Normal   empty
[    0.000000]   HighMem  [mem 0x0000000070000000-0x000000007dffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x000000007dffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007dffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: Using PSCI v0.1 Function IDs from DT
[    0.000000] percpu: Embedded 13 pages/cpu s23060 r8192 d21996 u53248
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 252224
[    0.000000] Kernel command line: console=ttyS0,115200 root=PARTUUID=38699229-01 rw rootwait
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000] Memory: 905092K/1015808K available (16384K kernel code, 1865K rwdata, 6312K rodata, 2048K init, 623K bss, 45180K reserved, 65536K cma-reserved, 163840K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000] 	Trampoline variant of Tasks RCU enabled.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000002] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000017] Switching to timer-based delay loop, resolution 41ns
[    0.001008] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.001466] Can't get timer clock
[    0.002994] Console: colour dummy device 80x30
[    0.003072] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.003094] pid_max: default: 32768 minimum: 301
[    0.003524] LSM: initializing lsm=capability,integrity,smack
[    0.003772] Smack:  Initializing.
[    0.003776] Smack:  IPv6 port labeling enabled.
[    0.004240] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.004264] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.005971] CPU: Testing write buffer coherency: ok
[    0.006635] /cpus/cpu@0 missing clock-frequency property
[    0.006673] /cpus/cpu@1 missing clock-frequency property
[    0.006699] /cpus/cpu@2 missing clock-frequency property
[    0.006725] /cpus/cpu@3 missing clock-frequency property
[    0.006742] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.007855] cblist_init_generic: Setting adjustable number of callback queues.
[    0.007871] cblist_init_generic: Setting shift to 2 and lim to 1.
[    0.008064] cblist_init_generic: Setting shift to 2 and lim to 1.
[    0.008247] Setting up static identity map for 0x40300000 - 0x403000ac
[    0.009366] rcu: Hierarchical SRCU implementation.
[    0.009373] rcu: 	Max phase no-delay instances is 1000.
[    0.010682] EFI services will not be available.
[    0.011251] smp: Bringing up secondary CPUs ...
[    0.022405] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.033495] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.044480] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.044593] smp: Brought up 1 node, 4 CPUs
[    0.044605] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[    0.044615] CPU: All CPU(s) started in HYP mode.
[    0.044619] CPU: Virtualization extensions available.
[    0.045588] devtmpfs: initialized
[    0.055618] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 3
[    0.056022] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.056088] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.059035] pinctrl core: initialized pinctrl subsystem
[    0.062466] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.070957] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.072180] audit: initializing netlink subsys (disabled)
[    0.072567] audit: type=2000 audit(0.048:1): state=initialized audit_enabled=0 res=1
[    0.074046] thermal_sys: Registered thermal governor 'fair_share'
[    0.074057] thermal_sys: Registered thermal governor 'bang_bang'
[    0.074062] thermal_sys: Registered thermal governor 'step_wise'
[    0.074067] thermal_sys: Registered thermal governor 'user_space'
[    0.074143] cpuidle: using governor menu
[    0.074418] No ATAGs?
[    0.074563] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.074574] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.075698] Serial: AMBA PL011 UART driver
[    0.087906] platform 1e40000.display-backend: Fixing up cyclic dependency with 1e20000.display-frontend
[    0.087992] platform 1e40000.display-backend: Fixing up cyclic dependency with 1e00000.display-frontend
[    0.088627] platform 1e50000.drc: Fixing up cyclic dependency with 1c0d000.lcd-controller
[    0.088752] platform 1e50000.drc: Fixing up cyclic dependency with 1c0c000.lcd-controller
[    0.088831] platform 1e50000.drc: Fixing up cyclic dependency with 1e40000.display-backend
[    0.089401] platform 1e60000.display-backend: Fixing up cyclic dependency with 1e20000.display-frontend
[    0.089484] platform 1e60000.display-backend: Fixing up cyclic dependency with 1e00000.display-frontend
[    0.090087] platform 1e70000.drc: Fixing up cyclic dependency with 1c0d000.lcd-controller
[    0.090189] platform 1e70000.drc: Fixing up cyclic dependency with 1c0c000.lcd-controller
[    0.090266] platform 1e70000.drc: Fixing up cyclic dependency with 1e60000.display-backend
[    0.093537] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
[    0.160914] raid6: neonx8   gen()   638 MB/s
[    0.229093] raid6: neonx4   gen()   906 MB/s
[    0.297239] raid6: neonx2   gen()   912 MB/s
[    0.365421] raid6: neonx1   gen()   747 MB/s
[    0.433596] raid6: int32x8  gen()   247 MB/s
[    0.501795] raid6: int32x4  gen()   256 MB/s
[    0.569918] raid6: int32x2  gen()   358 MB/s
[    0.638081] raid6: int32x1  gen()   317 MB/s
[    0.638089] raid6: using algorithm neonx2 gen() 912 MB/s
[    0.706213] raid6: .... xor() 679 MB/s, rmw enabled
[    0.706219] raid6: using neon recovery algorithm
[    0.711055] iommu: Default domain type: Translated
[    0.711064] iommu: DMA domain TLB invalidation policy: strict mode
[    0.712267] SCSI subsystem initialized
[    0.712875] usbcore: registered new interface driver usbfs
[    0.712917] usbcore: registered new interface driver hub
[    0.712964] usbcore: registered new device driver usb
[    0.713987] mc: Linux media interface: v0.10
[    0.714027] videodev: Linux video capture interface: v2.00
[    0.714147] pps_core: LinuxPPS API ver. 1 registered
[    0.714155] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[    0.714179] PTP clock support registered
[    0.714290] EDAC MC: Ver: 3.0.0
[    0.715800] Advanced Linux Sound Architecture Driver Initialized.
[    0.717015] NetLabel: Initializing
[    0.717022] NetLabel:  domain hash size = 128
[    0.717027] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.717132] NetLabel:  unlabeled traffic allowed by default
[    0.717535] vgaarb: loaded
[    0.718125] clocksource: Switched to clocksource arch_sys_counter
[    0.718998] VFS: Disk quotas dquot_6.6.0
[    0.719101] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.732076] NET: Registered PF_INET protocol family
[    0.732395] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.735408] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.735597] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.735640] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.735793] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    0.736179] TCP: Hash tables configured (established 8192 bind 8192)
[    0.736618] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear)
[    0.736769] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.736836] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.737130] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.737949] RPC: Registered named UNIX socket transport module.
[    0.737960] RPC: Registered udp transport module.
[    0.737966] RPC: Registered tcp transport module.
[    0.737970] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.737984] NET: Registered PF_XDP protocol family
[    0.738002] PCI: CLS 0 bytes, default 64
[    0.738864] Trying to unpack rootfs image as initramfs...
[    0.750889] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing.
[    0.751352] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.753586] Initialise system trusted keyrings
[    0.753963] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[    0.754249] zbud: loaded
[    0.756353] NFS: Registering the id_resolver key type
[    0.756397] Key type id_resolver registered
[    0.756404] Key type id_legacy registered
[    0.756510] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.756520] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    0.852453] xor: measuring software checksum speed
[    0.860226]    arm4regs        :  1300 MB/sec
[    0.871869]    8regs           :   846 MB/sec
[    0.883532]    32regs          :   844 MB/sec
[    0.890913]    neon            :  1344 MB/sec
[    0.890927] xor: using function: neon (1344 MB/sec)
[    0.890970] Key type asymmetric registered
[    0.890981] Asymmetric key parser 'x509' registered
[    0.891446] bounce: pool size: 64 pages
[    0.891729] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[    0.892197] io scheduler mq-deadline registered
[    0.892212] io scheduler kyber registered
[    0.892401] io scheduler bfq registered
[    0.921478] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled
[    0.925385] Serial: AMBA driver
[    0.944987] loop: module loaded
[    0.952833] Loading iSCSI transport class v2.0-870.
[    0.953507] iscsi: registered transport (tcp)
[    0.965543] usbcore: registered new interface driver uas
[    0.965603] usbcore: registered new interface driver usb-storage
[    0.965636] usbcore: registered new interface driver ums-cypress
[    0.965668] usbcore: registered new interface driver ums_eneub6250
[    0.965699] usbcore: registered new interface driver ums-freecom
[    0.965730] usbcore: registered new interface driver ums-isd200
[    0.965762] usbcore: registered new interface driver ums-usbat
[    0.971923] sun6i-rtc 1f00000.rtc: registered as rtc0
[    0.971972] sun6i-rtc 1f00000.rtc: setting system clock to 1970-01-01T00:00:27 UTC (27)
[    0.972115] sun6i-rtc 1f00000.rtc: RTC enabled
[    0.972718] i2c_dev: i2c /dev entries driver
[    0.981634] sdhci: Secure Digital Host Controller Interface driver
[    0.981657] sdhci: Copyright(c) Pierre Ossman
[    0.982654] Synopsys Designware Multimedia Card Interface Driver
[    0.983273] VUB300 Driver rom wait states = 1C irqpoll timeout = 0400
[    0.984051] usbcore: registered new interface driver vub300
[    0.984112] usbcore: registered new interface driver ushc
[    0.985073] sdhci-pltfm: SDHCI platform and OF driver helper
[    0.987212] ledtrig-cpu: registered to indicate activity on CPUs
[    0.988061] hid: raw HID events driver (C) Jiri Kosina
[    0.988572] usbcore: registered new interface driver usbhid
[    0.988588] usbhid: USB HID core driver
[    0.995142] NET: Registered PF_INET6 protocol family
[    1.211908] Freeing initrd memory: 6996K
[    1.264015] Segment Routing with IPv6
[    1.264142] In-situ OAM (IOAM) with IPv6
[    1.264271] mip6: Mobile IPv6
[    1.264305] NET: Registered PF_PACKET protocol family
[    1.264604] Key type dns_resolver registered
[    1.264810] ThumbEE CPU extension supported.
[    1.264823] Registering SWP/SWPB emulation handler
[    1.279695] registered taskstats version 1
[    1.279968] Loading compiled-in X.509 certificates
[    1.281202] zswap: loaded using pool lzo/zbud
[    1.292450] Key type .fscrypt registered
[    1.292466] Key type fscrypt-provisioning registered
[    1.299624] Btrfs loaded, crc32c=crc32c-generic, zoned=yes, fsverity=yes
[    1.324762] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[    1.330801] sun6i-a31-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[    1.331602] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[    1.334678] sun6i-a31-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver
[    1.335643] sun6i-a31-pinctrl 1c20800.pinctrl: supply vcc-ph not found, using dummy regulator
[    1.336498] printk: console [ttyS0] disabled
[    1.336600] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 235, base_baud = 1500000) is a 16550A
[    1.336741] printk: console [ttyS0] enabled
[    2.637450] sun6i-a31-r-pinctrl 1f02c00.pinctrl: supply vcc-pl not found, using dummy regulator
[    2.647497] axp20x-i2c 3-0068: AXP20x variant AXP221 found
[    2.662846] axp20x-gpio axp20x-gpio: DMA mask not set
[    2.669568] axp20x-gpio axp20x-gpio: AXP209 pinctrl and GPIO driver loaded
[    2.690724] vcc-wifi: Bringing 700000uV into 3300000-3300000uV
[    2.699549] vddio-csi: Bringing 700000uV into 2800000-2800000uV
[    2.710993] axp20x-i2c 3-0068: AXP20X driver loaded
[    2.718827] sun6i-a31-pinctrl 1c20800.pinctrl: supply vcc-pf not found, using dummy regulator
[    2.722964] ehci-platform 1c1a000.usb: EHCI Host Controller
[    2.726045] ALSA device list:
[    2.726057]   No soundcards found.
[    2.727593] ehci-platform 1c1b000.usb: EHCI Host Controller
[    2.729447] ohci-platform 1c1b400.usb: Generic Platform OHCI controller
[    2.729486] ohci-platform 1c1b400.usb: new USB bus registered, assigned bus number 1
[    2.730259] ohci-platform 1c1a400.usb: Generic Platform OHCI controller
[    2.730310] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2
[    2.733030] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 3
[    2.736008] ehci-platform 1c1b000.usb: new USB bus registered, assigned bus number 4
[    2.736533] ohci-platform 1c1b400.usb: irq 269, io mem 0x01c1b400
[    2.795449] ohci-platform 1c1a400.usb: irq 270, io mem 0x01c1a400
[    2.801840] sun6i-a31-pinctrl 1c20800.pinctrl: supply vcc-pa not found, using dummy regulator
[    2.803834] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.02
[    2.810573] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[    2.818648] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.830331] usb usb1: Product: Generic Platform OHCI controller
[    2.836269] usb usb1: Manufacturer: Linux 6.2.1-1-ARCH ohci_hcd
[    2.842209] usb usb1: SerialNumber: 1c1b400.usb
[    2.842336] ehci-platform 1c1a000.usb: irq 266, io mem 0x01c1a000
[    2.847655] hub 1-0:1.0: USB hub found
[    2.848747] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB
[    2.863675] hub 1-0:1.0: 1 port detected
[    2.863924] ehci-platform 1c1b000.usb: irq 267, io mem 0x01c1b000
[    2.868296] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.02
[    2.870134] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00
[    2.886137] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00
[    2.888105] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.901413] usb usb2: Product: Generic Platform OHCI controller
[    2.907404] usb usb2: Manufacturer: Linux 6.2.1-1-ARCH ohci_hcd
[    2.913359] usb usb2: SerialNumber: 1c1a400.usb
[    2.918639] hub 2-0:1.0: USB hub found
[    2.922440] hub 2-0:1.0: 1 port detected
[    2.926992] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.02
[    2.935317] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.942562] usb usb3: Product: EHCI Host Controller
[    2.947460] usb usb3: Manufacturer: Linux 6.2.1-1-ARCH ehci_hcd
[    2.953398] usb usb3: SerialNumber: 1c1a000.usb
[    2.958609] hub 3-0:1.0: USB hub found
[    2.962426] hub 3-0:1.0: 1 port detected
[    2.967038] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.02
[    2.971113] mmc0: host does not support reading read-only switch, assuming write-enable
[    2.975326] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.988094] mmc0: new high speed SDHC card at address aaaa
[    2.990542] usb usb4: Product: EHCI Host Controller
[    2.990550] usb usb4: Manufacturer: Linux 6.2.1-1-ARCH ehci_hcd
[    3.002689] mmcblk0: mmc0:aaaa AALCD 29.7 GiB
[    3.006852] usb usb4: SerialNumber: 1c1b000.usb
[    3.016686] hub 4-0:1.0: USB hub found
[    3.019761]  mmcblk0: p1
[    3.020530] hub 4-0:1.0: 1 port detected
[    3.030388] Freeing unused kernel image (initmem) memory: 2048K
[    3.036691] Run /init as init process
:: running early hook [udev]
Starting systemd-udevd version 253-1-arch
:: running hook [udev]
:: Triggering uevents...
[    3.226198] usb 3-1: new high-speed USB device number 2 using ehci-platform
[    3.387188] usb 3-1: New USB device found, idVendor=0bda, idProduct=0724, bcdDevice= 2.00
[    3.395427] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.402592] usb 3-1: Product: 802.11n WLAN Adapter
[    3.407408] usb 3-1: Manufacturer: Realtek
[    3.411526] usb 3-1: SerialNumber: 00e04c000001
:: running hook [keymap]
:: Loading keymap...kbd_mode: KDSKBMODE: Inappropriate ioctl for device
%@done.
:: performing fsck on '/dev/mmcblk0p1'
/dev/mmcblk0p1: recovering journal
/dev/mmcblk0p1: clean, 36717/1949696 files, 483839/7791488 blocks
:: mounting '/dev/mmcblk0p1' on real root
[    5.119466] EXT4-fs (mmcblk0p1): mounted filesystem 0152a639-8477-4714-9af6-521d8b8fb823 with ordered data mode. Quota mode: none.
:: running cleanup hook [udev]
[    5.765331] systemd[1]: System time before build time, advancing clock.
[    5.915166] systemd[1]: systemd 253-1-arch running in system mode (+PAM +AUDIT -SELINUX -APPARMOR -IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT -QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD +BPF_FRAMEWORK +XKBCOMMON +UTMP -SYSVINIT default-hierarchy=unified)
[    5.947512] systemd[1]: Detected architecture arm.

Welcome to Arch Linux ARM!

[    5.978776] systemd[1]: Hostname set to <alarm>.
[    6.491793] systemd[1]: bpf-lsm: BPF LSM hook not enabled in the kernel, BPF LSM not supported
[    7.417393] systemd[1]: Queued start job for default target Graphical Interface.
[    7.453936] systemd[1]: Created slice Slice /system/getty.
[  OK  ] Created slice Slice /system/getty.
[    7.477295] systemd[1]: Created slice Slice /system/modprobe.
[  OK  ] Created slice Slice /system/modprobe.
[    7.500957] systemd[1]: Created slice Slice /system/serial-getty.
[  OK  ] Created slice Slice /system/serial-getty.
[    7.524179] systemd[1]: Created slice User and Session Slice.
[  OK  ] Created slice User and Session Slice.
[    7.546823] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[  OK  ] Started Dispatch Password 
ts to Console Directory Watch.
[    7.574753] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[  OK  ] Started Forward Password R
uests to Wall Directory Watch.
[    7.599593] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[  OK  ] Set up automount Arbitrary
s File System Automount Point.
[    7.626575] systemd[1]: Reached target Local Encrypted Volumes.
[  OK  ] Reached target Local Encrypted Volumes.
[    7.650501] systemd[1]: Reached target Local Integrity Protected Volumes.
[  OK  ] Reached target Local Integrity Protected Volumes.
[    7.674638] systemd[1]: Reached target Path Units.
[  OK  ] Reached target Path Units.
[    7.694453] systemd[1]: Reached target Remote File Systems.
[  OK  ] Reached target Remote File Systems.
[    7.714341] systemd[1]: Reached target Slice Units.
[  OK  ] Reached target Slice Units.
[    7.734426] systemd[1]: Reached target Swaps.
[  OK  ] Reached target Swaps.
[    7.754421] systemd[1]: Reached target Local Verity Protected Volumes.
[  OK  ] Reached target Local Verity Protected Volumes.
[    7.779039] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[  OK  ] Listening on Device-mapper event daemon FIFOs.
[    7.819081] systemd[1]: Listening on Process Core Dump Socket.
[  OK  ] Listening on Process Core Dump Socket.
[    7.843465] systemd[1]: Listening on Journal Socket (/dev/log).
[  OK  ] Listening on Journal Socket (/dev/log).
[    7.867322] systemd[1]: Listening on Journal Socket.
[  OK  ] Listening on Journal Socket.
[    7.887460] systemd[1]: Listening on Network Service Netlink Socket.
[  OK  ] Listening on Network Service Netlink Socket.
[    7.911449] systemd[1]: Listening on udev Control Socket.
[  OK  ] Listening on udev Control Socket.
[    7.935089] systemd[1]: Listening on udev Kernel Socket.
[  OK  ] Listening on udev Kernel Socket.
[    7.959224] systemd[1]: Huge Pages File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/mm/hugepages).
[    7.998717] systemd[1]: Mounting POSIX Message Queue File System...
         Mounting POSIX Message Queue File System...
[    8.030088] systemd[1]: Mounting Kernel Debug File System...
         Mounting Kernel Debug File System...
[    8.051172] systemd[1]: Kernel Trace File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing).
[    8.090677] systemd[1]: Mounting Temporary Directory /tmp...
         Mounting Temporary Directory /tmp...
[    8.119409] systemd[1]: Starting Create List of Static Device Nodes...
         Starting Create List of Static Device Nodes...
[    8.151052] systemd[1]: Starting Load Kernel Module configfs...
         Starting Load Kernel Module configfs...
[    8.191289] systemd[1]: Starting Load Kernel Module dm_mod...
         Starting Load Kernel Module dm_mod...
[    8.219443] systemd[1]: Starting Load Kernel Module drm...
         Starting Load Kernel Module drm...
[    8.241196] device-mapper: uevent: version 1.0.3
[    8.246908] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: [email protected]
[    8.271171] systemd[1]: Starting Load Kernel Module fuse...
         Starting Load Kernel Module fuse...
[    8.299951] systemd[1]: Starting Load Kernel Module loop...
         Starting Load [    8.308028] fuse: init (API version 7.38)
Kernel Module loop...
[    8.367339] systemd[1]: Starting Journal Service...
         Starting Journal Service...
[    8.392604] systemd[1]: Load Kernel Modules was skipped because no trigger condition checks were met.
[    8.427535] systemd[1]: Starting Generate network units from Kernel command line...
         Starting Generate network 
ts from Kernel command line...
[    8.459926] systemd-journald[154]: Collecting audit messages is disabled.
[    8.464288] systemd[1]: Starting Remount Root and Kernel File Systems...
         Starting Remount Root and Kernel File Systems...
[    8.501277] systemd[1]: Starting Apply Kernel Variables...
         Starting Apply Kernel Variables...
[    8.549740] systemd[1]: Starting Coldplug All udev Devices...
         Starting Coldplug All udev Devices...
[    8.594725] systemd[1]: Mounted POSIX Message Queue File System.
[  OK  ] Mounted POSIX Message Queue File System.
[    8.620088] systemd[1]: Mounted Kernel Debug File System.
[  OK  ] Mounted Kernel Debug File System.
[    8.643808] systemd[1]: Mounted Temporary Directory /tmp.
[  OK  ] Mounted Temporary Directory /tmp.
[    8.668665] systemd[1]: Finished Create List of Static Device Nodes.
[  OK  ] Finished Create List of Static Device Nodes.
[    8.691944] systemd[1]: Started Journal Service.
[  OK  ] Started Journal Service.
[  OK  ] Finished Load Kernel Module configfs.
[  OK  ] Finished Load Kernel Module dm_mod.
[  OK  ] Finished Load Kernel Module drm.
[  OK  ] Finished Load Kernel Module fuse.
[  OK  ] Finished Load Kernel Module loop.
[  OK  ] Finished Generate network units from Kernel command line.
[  OK  ] Finished Remount Root and Kernel File Systems.
[  OK  ] Finished Apply Kernel Variables.
[  OK  ] Reached target Preparation for Network.
         Mounting FUSE Control File System...
         Mounting Kernel Configuration File System...
         Starting Flush Journal to Persistent Storage...
         Starting Load/Save OS Random Seed...
         Starting Creat[    9.032637] systemd-journald[154]: Received client request to flush runtime journal.
e Static Device Nodes in /dev...
[    9.066596] systemd-journald[154]: File /var/log/journal/dbd679b11803469e8526c76d2e3d84fc/system.journal corrupted or uncleanly shut down, renaming and replacing.
[  OK  ] Mounted FUSE Control File System.
[  OK  ] Mounted Kernel Configuration File System.
[  OK  ] Finished Flush Journal to Persistent Storage.
[  OK  ] Finished Create Static Device Nodes in /dev.
[  OK  ] Reached target Preparation for Local File Systems.
[  OK  ] Reached target Local File Systems.
         Starting Create Volatile Files and Directories...
         Starting Rule-based Manage
for Device Events and Files...
[  OK  ] Finished Coldplug All udev Devices.
[   10.066158] random: crng init done
[  OK  ] Finished Load/Save OS Random Seed.
[  OK  ] Started Rule-based Manager for Device Events and Files.
         Starting Network Configuration...
[  OK  ] Finished Create Volatile Files and Directories.
         Starting Network Name Resolution...
         Starting Network Time Synchronization...
         Starting Record System Boot/Shutdown in UTMP...
[  OK  ] Found device /dev/ttyS0.
[   10.584537] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   10.641212] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   10.668474] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[   10.686265] cfg80211: failed to load regulatory.db
[  OK  ] Finished Record System Boot/Shutdown in UTMP.
[  OK  ] Started Network Configuration.
[  OK  ] Started Network Time Synchronization.
[  OK  ] Reached target System Time Set.
[   11.557048] sun4i-ss 1c15000.crypto-engine: Die ID 5
[   11.676832] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=1)
[  OK  ] Started Network Name Resolution.
[  OK  ] Reached target Network.
[  OK  ] Reached target Host and Network Name Lookups.
[  OK  ] Reached target System Initialization.
[  OK  ] Started Refresh existing P
f archlinux-keyring regularly.
[  OK  ] Started Daily verification of password and group files.
[   11.834596] Bluetooth: Core ver 2.22
[  OK  ] Started Daily Cleanup of Temporary Directories.[   11.844360] NET: Registered PF_BLUETOOTH protocol family

[   11.854986] Bluetooth: HCI device and connection manager initialized
[  OK  ] Reached target Timer Units.
[   11.870221] Bluetooth: HCI socket layer initialized
[   11.875425] Bluetooth: L2CAP socket layer initialized
[  OK  ] Listening on D-Bus System Message Bus Socket.
[   11.892592] Bluetooth: SCO socket layer initialized
[  OK  ] Reached target Socket Units.
[  OK  ] Reached target Basic System.
[   11.943364] usb 3-1: This Realtek USB WiFi dongle (0x0bda:0x0724) is untested!
[   11.950975] usb 3-1: Please report results to [email protected]
         Starting D-Bus System Message Bus...
[   11.981013] input: axp20x-pek as /devices/platform/soc/1f03400.i2c/i2c-3/3-0068/axp221-pek/input/input0
[   12.009836] axp20x-adc axp22x-adc: DMA mask not set
[  OK  ] Started OpenSSH Daemon.
         Starting User Login Management...
         Starting Permit User Sessions...
[  OK  ] Finished Permit User Sessions.
[   12.209085] usb 3-1: Vendor: Realtek
[   12.213525] usb 3-1: Product: 802.11n WLAN Adapter
[   12.220308] usb 3-1: RTL8723AU rev B (UMC) 1T1R, TX queues 2, WiFi=1, BT=1, GPS=0, HI PA=0
[   12.229641] usb 3-1: RTL8723AU MAC: 8c:18:d9:94:e5:c0
[   12.234924] usb 3-1: rtl8xxxu: Loading firmware rtlwifi/rtl8723aufw_B_NoBT.bin
[  OK  ] Started Getty on tty1.
[   12.271432] usb 3-1: Firmware revision 31.0 (signature 0x2302)
[  OK  ] Started Serial Getty on ttyS0.
[  OK  ] Reached target Login Prompts.
[  OK  ] Started D-Bus System Message Bus.
[   12.413224] ------------[ cut here ]------------
[   12.420138] WARNING: CPU: 3 PID: 172 at drivers/base/platform.c:452 __platform_get_irq_byname+0xbc/0xcc
[   12.433482] 0 is an invalid IRQ number
[  OK  ] Listening on Load/Save RF 
itch Status /dev/rfkil[   12.445676] Modules linked in: evdev sun4i_gpadc_iio(+) axp20x_adc btusb(+) axp20x_pek btrtl rtl8xxxu(+) btbcm btintel btmtk mac80211 bluetooth libarc4 sun4i_ts sun4i_backend sun4i_frontend sun4i_gpadc ecdh_generic sun6i_drc drm_dma_helper ecc sunxi_wdt sun4i_ss sun4i_tcon sun8i_tcon_top cfg80211 rfkill uio_pdrv_genirq uio sch_fq_codel fuse dm_mod ip_tables x_tables
l Watch.
[   12.478537] CPU: 2 PID: 172 Comm: (udev-worker) Not tainted 6.2.1-1-ARCH #1
[   12.486525] Hardware name: Allwinner sun6i (A31) Family
[   12.491788]  unwind_backtrace from show_stack+0x10/0x14
[   12.497077]  show_stack from dump_stack_lvl+0x40/0x4c
[   12.497112]  dump_stack_lvl from __warn+0x84/0xc4
[   12.497128]  __warn from warn_slowpath_fmt+0x78/0xac
[   12.497142]  warn_slowpath_fmt from __platform_get_irq_byname+0xbc/0xcc
[   12.497164]  __platform_get_irq_byname from platform_get_irq_byname+0x10/0x30
[   12.497182]  platform_get_irq_byname from sun4i_irq_init+0x38/0xcc [sun4i_gpadc_iio]
[   12.497241]  sun4i_irq_init [sun4i_gpadc_iio] from sun4i_gpadc_probe+0x21c/0x304 [sun4i_gpadc_iio]
[   12.497281]  sun4i_gpadc_probe [sun4i_gpadc_iio] from platform_probe+0x5c/0xb0
[   12.497311]  platform_probe from really_probe+0xc8/0x2ec
[   12.497335]  really_probe from __driver_probe_device+0x84/0xe4
[   12.497359]  __driver_probe_device from driver_probe_device+0x30/0x104
[   12.497383]  driver_probe_device from __driver_attach+0x90/0x174
[   12.497407]  __driver_attach from bus_for_each_dev+0x74/0xc0
[   12.497432]  bus_for_each_dev from bus_add_driver+0x164/0x1f0
[   12.497454]  bus_add_driver from driver_register+0x88/0x11c
[   12.497472]  driver_register from do_one_initcall+0x48/0x230
[   12.497489]  do_one_initcall from do_init_module+0x44/0x1e8
[   12.497516]  do_init_module from sys_init_module+0x194/0x1bc
[   12.497539]  sys_init_module from __sys_trace_return+0x0/0x10
[   12.497559] Exception stack(0xf0db5fa8 to 0xf0db5ff0)
[   12.497572] 5fa0:                   00000000 b4fcf008 b4fcf008 00003e64 b6c13640 00000000
[   12.497584] 5fc0: 00000000 b4fcf008 b6c13640 00000080 024b32f8 024b3870 00000000 00000000
[   12.497593] 5fe0: b6c24f28 bead7738 b6c0a5c0 b6ad0100
[   12.497758] ---[ end trace 0000000000000000 ]---
[   12.497781] sun4i-gpadc-iio sun6i-a31-gpadc-iio.0: error -EINVAL: IRQ FIFO_DATA_PENDING not found
[   12.653730] sun4i-gpadc-iio: probe of sun6i-a31-gpadc-iio.0 failed with error -22
[  OK  ] Started User Login Management.
[  OK  ] Reached target Multi-User System.
[  OK  ] Reached target Graphical Interface.
[   12.915755] usbcore: registered new interface driver rtl8xxxu
[   12.926174] usbcore: registered new interface driver btusb
[   12.929155] Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=1200
[   12.940567] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723a_fw.bin
[   12.985526] rtl8xxxu 3-1:1.2 wlu1i2: renamed from wlan0
[   13.646088] Bluetooth: hci0: RTL: fw version 0x0e3da5b1



Arch Linux 6.2.1-1-ARCH (ttyS0)

alarm login: