U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:46:11 -0700)
ZyXEL NSA320 2-Bay Power Media Server

SoC:   Kirkwood 88F6281_A1
DRAM:  512 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot:  0
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found

Reset IDE: ide_preinit failed
Unknown command 'mmc' - try 'help'

Partition Map for USB device 0  --   Partition Type: DOS

Part    Start Sector    Num Sectors     UUID            Type
  1     2048            61339648        000b6a86-01     83

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **

no IDE devices available
Unknown command 'mmc' - try 'help'
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 692 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
3821592 bytes read in 916 ms (4 MiB/s)
loading uInitrd ...
7245696 bytes read in 943 ms (7.3 MiB/s)
loading DTB /boot/dts/kirkwood-pogo_e02.dtb ...
10444 bytes read in 3583 ms (2 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-4.12.1-kirkwood-tld-1
   Created:      2017-07-20   8:11:24 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3821528 Bytes = 3.6 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-4.12.1-kirkwood-tld-1
   Created:      2017-07-24   0:18:23 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7245632 Bytes = 6.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
   Booting using the fdt blob at 0x1c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 0f917000, end 0fffff40 ... OK
   Loading Device Tree to 0f911000, end 0f9168cb ... OK
Using machid 0x831 from environment

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:7
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] OF: fdt: Machine model: CloudEngines Pogoplug E02
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(r)
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 499276K/524288K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 25012K reserved, )
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xff800000   ( 496 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0900000   (9184 kB)
[    0.000000]       .init : 0xc0c00000 - 0xc0d00000   (1024 kB)
[    0.000000]       .data : 0xc0d00000 - 0xc0db3274   ( 717 kB)
[    0.000000]        .bss : 0xc0db9b9c - 0xc0e01e60   ( 289 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.000042] Switching to timer-based delay loop, resolution 5ns
[    0.000500] Console: colour dummy device 80x30
[    0.000532] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[    0.000555] pid_max: default: 32768 minimum: 301
[    0.000755] Security Framework initialized
[    0.000875] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000895] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001742] CPU: Testing write buffer coherency: ok
[    0.002732] Setting up static identity map for 0x100000 - 0x100058
[    0.002990] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[    0.006257] devtmpfs: initialized
[    0.010042] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.010131] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.010528] prandom: seed boundary self test passed
[    0.014265] prandom: 100 self tests passed
[    0.014278] pinctrl core: initialized pinctrl subsystem
[    0.015392] NET: Registered protocol family 16
[    0.015861] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.017424] cpuidle: using governor ladder
[    0.017496] cpuidle: using governor menu
[    0.017915] Feroceon L2: Enabling L2
[    0.017961] Feroceon L2: Cache support initialised.
[    0.018326] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[    0.022792] No ATAGs?
[    0.031790] vgaarb: loaded
[    0.032102] SCSI subsystem initialized
[    0.032571] usbcore: registered new interface driver usbfs
[    0.032646] usbcore: registered new interface driver hub
[    0.032728] usbcore: registered new device driver usb
[    0.033796] clocksource: Switched to clocksource orion_clocksource
[    0.122356] VFS: Disk quotas dquot_6.6.0
[    0.122434] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.132965] NET: Registered protocol family 2
[    0.133703] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.133764] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    0.133864] TCP: Hash tables configured (established 4096 bind 4096)
[    0.133956] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.133981] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.134154] NET: Registered protocol family 1
[    0.134553] RPC: Registered named UNIX socket transport module.
[    0.134566] RPC: Registered udp transport module.
[    0.134573] RPC: Registered tcp transport module.
[    0.134580] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.134814] Unpacking initramfs...
[    0.788985] Freeing initrd memory: 7076K
[    0.789121] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.790063] audit: initializing netlink subsys (disabled)
[    0.790536] Initialise system trusted keyrings
[    0.790594] Key type blacklist registered
[    0.790688] audit: type=2000 audit(0.786:1): state=initialized audit_enabled=0 res=1
[    0.790784] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[    0.790852] zbud: loaded
[    0.791814] NFS: Registering the id_resolver key type
[    0.791842] Key type id_resolver registered
[    0.791851] Key type id_legacy registered
[    0.791868] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.791878] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.792081] jffs2: version 2.2. (NAND) (SUMMARY)  �© 2001-2006 Red Hat, Inc.
[    0.792280] fuse init (API version 7.26)
[    0.792644] orangefs_debugfs_init: called with debug mask: :none: :0:
[    0.792900] orangefs_init: module version upstream loaded
[    0.792910] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[    2.553806] random: fast init done
[    6.637348] Key type asymmetric registered
[    6.637365] Asymmetric key parser 'x509' registered
[    6.637432] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    6.637443] io scheduler noop registered
[    6.637451] io scheduler deadline registered
[    6.637528] io scheduler cfq registered (default)
[    6.638827] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    6.640666] mv_xor f1060800.xor: Marvell shared XOR driver
[    6.694532] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr )
[    6.694746] mv_xor f1060900.xor: Marvell shared XOR driver
[    6.754530] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr )
[    6.754935] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    6.756158] console [ttyS0] disabled
[    6.756222] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A
[    7.356810] console [ttyS0] enabled
[    7.368726] loop: module loaded
[    7.372714] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[    7.379175] nand: Samsung NAND 128MiB 3,3V 8-bit
[    7.383846] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    7.391457] Scanning device for bad blocks
[    7.461572] Bad eraseblock 620 at 0x000004d80000
[    7.484029] Bad eraseblock 788 at 0x000006280000
[    7.493609] Bad eraseblock 835 at 0x000006860000
[    7.518287] 4 cmdlinepart partitions found on MTD device orion_nand
[    7.524598] Creating 4 MTD partitions on "orion_nand":
[    7.529762] 0x000000000000-0x000000100000 : "u-boot"
[    7.535940] 0x000000100000-0x000000500000 : "uImage"
[    7.542070] 0x000000500000-0x000002500000 : "rootfs"
[    7.548445] 0x000002500000-0x000008000000 : "data"
[    7.556179] libphy: Fixed MDIO Bus: probed
[    7.561112] libphy: orion_mdio_bus: probed
[    7.565644] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    7.573051] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.579691] ehci-pci: EHCI PCI platform driver
[    7.584263] ehci-orion: EHCI orion driver
[    7.588470] orion-ehci f1050000.ehci: EHCI Host Controller
[    7.594060] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    7.601908] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[    7.633829] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    7.640115] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    7.646969] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.654249] usb usb1: Product: EHCI Host Controller
[    7.659147] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd
[    7.665898] usb usb1: SerialNumber: f1050000.ehci
[    7.671365] hub 1-0:1.0: USB hub found
[    7.675235] hub 1-0:1.0: 1 port detected
[    7.679844] usbcore: registered new interface driver usb-storage
[    7.686298] mousedev: PS/2 mouse device common for all mice
[    7.692503] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[    7.699616] i2c /dev entries driver
[    7.704450] hidraw: raw HID events driver (C) Jiri Kosina
[    7.710209] drop_monitor: Initializing network drop monitor service
[    7.716794] NET: Registered protocol family 17
[    7.721331] Key type dns_resolver registered
[    7.726388] registered taskstats version 1
[    7.730501] Loading compiled-in X.509 certificates
[    7.735400] zswap: loaded using pool lzo/zbud
[    7.749820] Key type big_key registered
[    7.762996] Key type encrypted registered
[    7.768690] rtc-mv f1010300.rtc: setting system clock to 2000-01-01 00:27:13 UTC (946686433)
[    7.780567] Freeing unused kernel memory: 1024K
Loading, please wait...
starting version 232
[    8.033900] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    8.235814] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[    8.242575] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    8.262967] usb 1-1: Product: USB2.0 Hub
[    8.271531] hub 1-1:1.0: USB hub found
[    8.280571] hub 1-1:1.0: 4 ports detected
Begin: Loading essential drivers ... done.
[    8.603829] usb 1-1.3: new high-speed USB device number 3 using orion-ehci
[    8.754797] usb 1-1.3: New USB device found, idVendor=0781, idProduct=5571
[    8.761719] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    8.769102] usb 1-1.3: Product: Cruzer Fit
[    8.773214] usb 1-1.3: Manufacturer: SanDisk
[    8.777523] usb 1-1.3: SerialNumber: 4C530001160702120375
[    8.790071] usb-storage 1-1.3:1.0: USB Mass Storage device detected
[    8.806929] scsi host0: usb-storage 1-1.3:1.0
[    8.813288] usbcore: registered new interface driver uas
[    9.844891] scsi 0:0:0:0: Direct-Access     SanDisk  Cruzer Fit       1.00 PQ: 0 ANSI: 6
[    9.858725] sd 0:0:0:0: [sda] 61341696 512-byte logical blocks: (31.4 GB/29.3 GiB)
[    9.874481] sd 0:0:0:0: [sda] Write Protect is off
[    9.883630] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    9.906449]  sda: sda1
[    9.915225] sd 0:0:0:0: [sda] Attached SCSI removable disk
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Warning: fsck not present, so skipping root file system
[   18.567875] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[   18.587975] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Setting hostname to 'debian'...done.
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
. ok
[....] Synthesizing the initial hotplug events...done.
[....] Waiting for /dev to be fully populated...[   20.947966] marvell-cesa f1030000.crypto: CESA device successfully registered
[   21.011993] orion_wdt: Initial timeout 21 sec
[   21.059183] sd 0:0:0:0: Attached scsi generic sg0 type 0
done.
[....] Activating swap:. ok
[   22.086641] EXT4-fs (sda1): re-mounted. Opts: (null)
[....] Will now check root file system:fsck from util-linux 2.29.2
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1
e2fsck 1.43.4 (31-Jan-2017)
rootfs: clean, 14455/1916928 files, 284746/7667456 blocks
. ok
[   22.405929] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[....] Will now activate lvm and md swap:done.
[info] Will now check all file systems.
fsck from util-linux 2.29.2
Checking all file systems.
LABEL=rootfs is mounted
[....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. ok
[....] Cleaning up temporary files...[....] Cleaning /tmp...done.
 /tmp. ok
[....] Will now mount local file[   24.420868] random: crng init done
systems:. ok
[....] Will now activate swapfile swap:done.
[....] Checking minimum space in /tmp...done.
[....] Cleaning up temporary files.... ok
[....] Setting kernel variables...done.
[....] Initializing random number generator...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5
Copyright 2004-2016 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Cannot find device "eth0"
Failed to get interface index: No such device

If you think you have received this message due to a bug rather
than a configuration issue please read the section on submitting
bugs on either our web page at www.isc.org or in the README file
before submitting a bug.  These pages explain the proper
process and the information we find helpful for debugging..

exiting.
ifup: failed to bring up eth0
failed.
[   25.662547] NET: Registered protocol family 10
[   25.669482] Segment Routing with IPv6
[....] Starting RPC port mapper daemon: rpcbind. ok
[....] Starting NFS common utilities: statd idmapd. ok
[....] Cleaning up temporary files.... ok
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1283 (syslogd)
. ok
[....] Starting system message bus: dbus. ok
[....] Starting NFS common utilities: statd idmapd. ok
[....] Not starting NFS kernel daemon: no exports. ... (warning).
[....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. ok
[....] Starting NTP server: ntpd. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1281 (klogd)
. ok
[....] Starting OpenBSD Secure Shell server: sshd. ok
[....] Running local boot scripts (/etc/rc.local). ok

Debian GNU/Linux 9 debian ttyS0